Construction of 1 No. of INS, 4 Nos. of SI, and 27 Nos. of PC/HC Quarters with development works at Kambainallur in Dharmapuri District

E0001) Earth work excavation for foundation in all soils (including refilling) a) 0 to 2 mt.

E0005) Earth work excavation for Open foundation (excluding refilling) a) 0 to 2 mt.

WS0278) Supply and delivery of clear water vertical wet type 3 phase 5 HP - Submersible pumpset with ISI mark suitable for 150mm dia borewell o. 50 lpm x 175 m

E0006) Earth work excavation for Open foundation for drains (excluding refilling) width upto 1.25 m a) 0 to 2 mt.

RE0006) Providing Pre-Constructional Antitermite treatment

WS0022) Supply and laying of following dia G.I pipes Below ground level a) 50mm dia GI Pipe

F0006) Supplying and filling with 40mm size Hard broken stone jelly in foundation and basement

F0007) Supplying and filling with 20mm size Hard broken stone jelly in foundation and basement

F0026) Filling in foundation and basement and other similar works with Excavated earth

F0013) Supply and filling in foundation and basement with gravel

CSMP0002) Plain cement concrete 1:5:10 (One of cement, five of crushed stone sand and ten of hard broken stone Jelly including Mortar Plasticizer (Liquid) at 200ml per bag) for foundation and basement using 40 mm gauge hard broken stone jelly

CSMP0003) Plain cement concrete 1:2:4 (One of cement two of crushed stone sand and four of Hard Broken Stone jelly) (including Mortar Plasticizer (Liquid) at 200ml per bag) using 20mm gauge hard broken stone jelly

CSMP0004) Plain cement concrete 1:8:16 (One of cement, eight of crushed stone sand and sixteen of broken brick jelly including Mortar Plasticizer (Liquid) at 200ml per bag) for foundation and other similar works using 20mm gauge broken Brick Jelly

CSMP0005) Plain cement concrete 1:3:6 (one of cement, three of crushed stone sand and six of hard broken stone jelly including Mortar Plasticizer (Liquid) at 200ml per bag) for foundation and other similar works using 20mm gauge hard broken stone jelly

CS0037) Supplying and fixing of precast cement concrete slab for cupboard / ward robes, shelves, cover slab for chambers baffle walls etc., and other similar works 20mm thick using standardised concrete mix M20 I. 20mm thick a) In Stilt / Ground Floor

b) In First Floor

c) In Second Floor

b) 2 to 3 mt.

d) In Third Floor

excavation, refilling, compacting providing 2' dia/ 450 x 450mm 9" thick brick masonry, GI funnel, salt and char coal, hinged cover thick brick masonry, GI funnel, salt and char coal, hinged cover fabricated out of angle iron frame and 7mm thick chequered plate etc., a) With 600 x 600 x 3mm Copper plate electrode

b) In Stilt / Ground Floor

c) In First Floor

C0049) Precast cement concrete Jally ventilator using standardised concrete mix M20 without vibrating charges 50mm thick a) In Ground Floor

b) In First Floor

C0065) Providing and laying in position, Standardised Concrete Mix M-20 Grade (Using crushed stone sand) a) In Foundation and Basement

b) In Stilt / Ground Floor

e) In Fourth Floor

c) In First Floor

d) In Second Floor

C0066) Providing and laying in position, Standardised Concrete Mix M-25 Grade (Using crushed stone sand) b) In Stilt / Ground Floor

e) In Third Floor

f) In Fourth Floor

g) In Fifth Floor

CSMP0001) Supplying and fixing of fibre mixed precast slab of 50mm thick of all required shapes made in cement concrete 1:3:6 (one of cement,three of crushed stone sand and six of 20mm hard broken stone jelly including Mortar Plasticizer (Liquid) at 200ml per bag) with secondary reinforcement fibre of approved quality at 0.25% by weight of cement (125gm of fibre for 1 bag i.e., 50Kg of cement) used including cost of all materials, moulding, curing, transportation, laying, pointing etc., for approach road,pavement slab and other similar works etc., complete as per the relevant standard specifications and as directed by the departmental officers.

C0022) Providing Rain Water Harvesting well ring in circular shape of 90cm dia, 60cm depth (30cm depth 2 Nos) 50mm thickness using standardised concrete mix M25 grade using 20mm HBSJ including cost of steel fabrication, labour charges, cost of materials, moulding, curing and hire charges for tools and plants etc., all complete and as directed by the departmental officers.

b) In First Floor

c) In Second Floor

b) 2 to 3 mt.

d) In Third Floor

BMP0006) Brick work in Cement Mortar 1:5 (One of cement and five of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) using Kiln burnt country bricks of size 8¾”x4¼”x2¾” (22x11x7cm) in foundation and basement

f) In Fifth Floor

c) In First Floor

d) In Second Floor

C0066) Providing and laying in position, Standardised Concrete Mix M-25 Grade (Using crushed stone sand) b) In Stilt / Ground Floor

e) In Third Floor

f) In Fourth Floor

b) In Ground Floor

b) In First Floor

b) 2 to 3 mt.

d) In Third Floor

BMP0007) Brick work in Cement Mortar 1:6 (One of cement and six of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) using Kiln burnt country bricks of size 8¾”x4¼”x2¾” (22x11x7cm) for super structure in the following floors a) In Ground Floor

c) In Second Floor

b) 2 to 3 mt.

d) In Third Floor

BMP0006) Brick work in Cement Mortar 1:5 (One of cement and five of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) using Kiln burnt country bricks of size 8¾”x4¼”x2¾” (22x11x7cm) in foundation and basement

FL0003) Supplying and fixing of 20mm thick Bituminous Expansion joint filler Pad

FLMP0001) Flooring with a bed of CC 1:5:10 (one of cement, five of crushed stone sand and ten of hard broken stone jelly including Mortar Plasticizer (Liquid) at 200ml per bag) using 40mm size hard broken stone jelly

FLMP0002) Plastering the top of flooring in CM 1:4 (One of cement and four of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 20mm thick

BMP0008) Brick partition wall in Cement Mortar 1:4 (One of cement and four of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 110mm thick for super structure in the following floors using Kiln burnt country bricks of size 8¾”x4¼x2¾” (22x11x7cm) a. In Foundation and basement

FL0025) Weathering Course with concrete broken brick jelly 20mm gauge

FLMP0004) Finishing top of roof with one course of Pressed Tiles of approved superior quality of size 23cmx 23cmx20mm thick laid over weathering course in CM 1:3 (One of cement and three of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag,) 12mm thick mixed with Water proofing compound at 2%

FLMP0005) Supplying and fixing of Colour glazed tiles (Best approved quality and the same shall be got approved from the Executive Engineer before using) over cement plastering in CM 1:2 (One of cement and two of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 10mm thick

FLMP0006) Supplying and fixing of colour Ceramic Tiles Anti skid without corrugated design for flooring and other similar works (Best approved quality, colour and shade shall be got approved from the Executive Engineer before using) over cement mortor 1:3 (One of cement and three of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 20mm thick

FL0024) Finishing the top of flooring with cement concrete 1:3 (One of cement and three of blue granite chips of size 10mm and below) 20 mm thick Ellispattern Flooring (No Sand)

FL0123) providing double nosing to the edges of granite slab of 20mm thick including labour, power consumption, tools & plants required, true to horizontal etc., for kitchen platform in all floors and as directed by the departmental officers.

FLMP0013) Supplying and fixing of Ruby Red / Raw silk colour Granite Tiles (superfine polished with machine cut edges) of required sizes of 10 mm thick for wall cladding (Best approved quality and the same shall be got approved from the Executive Engineer before using) over cement plastering in CM 1:2 (One of cement and two of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 10 mm thick

FLMP0011) Supply and laying superior variety Concrete Designer tiles for flooring in CM 1:3 (One of Cement and three of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 20mm thick

FLMP0009) Supplying and fixing of Stain free Nano polish Vitrified Tiles of size (600x600x8mm) for flooring and other similar works in cement mortar 1:3 (one of cement and three of crushed stone sand, including Mortar Plasticizer (Liquid) at 200ml per bag) 20mm thick

LPS0024.b) With 100mm dia 3M long CI Pipe electrode

SA0051) Supplying and fixing of the following dia stone ware bend with ISI mark Superior variety a) 100mm dia SW bend

JD0004) Supplying and fixing of Teak wood Panelled Single leaves door shutters with Brass fittings Suitable for Door of size a) 1000 x 2100 mm

d. In Third Floor

LPS0024.c) Chemical Earthing Copper Coated: T-39 Cu. (80mm dia) - 3 mtrs with Back Fill Compund (25 kgs per Bag) includes Providing of RCC Chamber and Civil finishing including painting. CER.No: 63 /2024-25

FW0004) Providing Form work and centering for reinforced cement concrete works a) For Column footings, plinth beam, Grade beam, Raft beam, Raft slab etc.,

b) Plain surfaces such as Roof slab, floor slab, Beams, lintels, lofts, sill slab, staircase waist, portico slab and other similar works

c) For Square and rectangular columns and small quantities such as sunshade, parapet cum drops window boxiing, fin projection and other similar works.

d) For Vertical wall

f) For Curved surface

PLMP0001) Plastering with CM 1:5 (One of cement and five of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 12mm thick

PLMP0002) Plastering with CM 1:4 (one of cement and four of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 12mm thick

PLMP0003) Special ceiling plastering in cement mortar 1:3 (One of cement and three of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 10mm thick

PLMP0004) Plastering in cm 1:3 (one of cement and three of crushed stone sand (One of cement and three of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 12mm tk. mixed with water proof compound at 2%

PLMP0005) Plastering in CM 1:5 (One of cement and five of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 12mm thick for border finish in all floors a) 150mm wide border

b) 75mm wide border

c) 50mm wide border

FLMP0017) Supplying and laying of Sinthetic Grey, Paradise and similar varieties Granite slabs (superfine polished with machine cut edges) of size 4'-0"x 2'-0" of 18 to 20 mm thick for flooring (Best approved quality and the same shall be got approved from the Executive Engineer before using) over cement plastering in CM 1:3 (One of cement and three of crushed stone sand) 20mm thick including Cost of Mortar Plasticizer (Liquid) at 200ml per bag

PL0027) Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

PA0001) White washing three coats using clean shell lime slaked

PA0022) Painting the new wood work with two coats of approved first class synthetic enamel ready mixed paint in addition to one coat of Primer

PA0026) Painting the new Iron work and other similar works such as PVC /ASTM Pipes, Kerb Stone and grills with two coats

PA0027) Providing wooden (melamine) polish for new wood

PA0032) Supplying and applying of full putty one coat with aproved make wall putty for smooth finishing the new cement plastered walls

PL0016) Stucco Plastering 12mm thick using hard broken stone chips of size 10mm and below using 86.50 kgs of cement and 0.15 m³ blue metal chips for every 10m² area over the existing plastered surface including curing etc., complete complying

PA0037) Painting the New walls with two coats of approved best ready mixed plastic emulsion paint for inner walls

PA0042) Painting the New walls with two coats of approved best ready mixed exterior emulsion paint outer walls in addition to one coat of approved primer coat

J0001) Supplying and fixing of Teak wood wrought and put up a) Teak wood over 2m and below 3m length

b) Teak wood below 2 m length

J0021) Supply and fixing of best approved superior variety magnetic door catches

J0029) Supplying of Mild Steel hold fasts horizontally twisted of size 230x40x4mm

JV0022) Supply and fixing of UPVC (Un plasticized polyvinyl chloride) Louvered ventilators

JW0042) Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of

JD0027) Supplying and fixing of T.W. single leaf Door shutters using 9 mm tk. phynol bonded BWR plywood shutters with brass screws a) 750 x 2100 mm

PA0043) Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing.

JD0095) Supply and Fixing of 25mm (+/- 1mm) thick WPC Decora Door which is extruded as a single core door with Lead-Free compound. The door is designed homogeneously by Smooth Routing and 3D embossed grains on one side. The other side of the door shutter shall be plain matt finish. The door must be completely made by machine, without any post-production fabrication. The Solid WPC board shall have minimum Bulk Density 650 KG/ Cub.Mt. The door is suggested to be hinged to the WPC frame of size 75 x 50mm with minimum of 5 inch butt hinges of SS including cost of WPC door frame, shutter, SS cylindrical lock and door closer and labour charges etc., complete complying with standard specifications and as directed by department officers. (The brand should be got approved from the Executive Engineer before use.)

GR0001) Supplying and fixing Mild Steel grills as per the design approved

EL0561) Supplying and fixing of Single Pole 6A to 32A, 10KA MINIATURE CIRCUIT BREAKERS 240 V / 415V 50HZ - AC Supply suiatble for both lighting and motor circuits etc., all complete and as directed by the departmental officers.

b. In First Floor

RE0004) Supplying, fabricating and placing in position of Mild steel Grills / Ribbed Tor Steels (without cement slurry)

JD0094) Providing T.W.double leaf shutters for cupboard/ward robes with 9mm thick phenol bonded BWR grade plywood

with relevant standard specifications and as directed by the departmental officers.

casement type (open)

c. In Second Floor

WS0033) Supplying and fixing of half turn C.P Long body Tap of 15mm dia

WS0036) Supplying and fixing of half turn C.P short body Tap of 15mm dia

FLMP0018) Supplying and fixing of pre-cast kerb stone of size 450x300x150mm made in CC 1:3:6 (One of cement, three of crushed stone sand and six of hard broken stone jelly) using 20mm size hard broken stone jelly including Cost of Mortar Plasticizer (Liquid) at 200ml per bag, the cost of Kerb stone moulding, laying, curing, transporting, pointing and as directed by the departmental officers..

BMP0010) Brick partition walls 50mm thick using kiln burnt country bricks of size 8¾”x4¼”x2” (22x11x5cm) in cement mortar 1:4 (One of cement and four of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) for super structure in the following floors a)

BMP0009) Brick partition walls 70mm thick using Kiln burnt country bricks of size 8¾”x4¼”x2¾” (22x11x7cm) in cement mortar 1:4 (One of cement and four of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) for super structure in the following floors a) In Ground Floor

WS0006) Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D - 1785 of schedule 40 of wall thickness a) 32mm dia ASTM D schedule 40 threaded PVC pipe with necessary PVC/GI/GM specials

b) 25mm dia ASTM D schedule 40 threaded PVC pipe with necessary PVC/GI/GM specials

e. In Fourth Floor

WS0002) Supplying and fixing of 110mm dia PVC SWR pipe with ISI mark conforming to IS 13952:1992- type `A` for Rain water down fall pipe

c) 50mm dia ASTM D schedule 40 threaded PVC pipe with necessary PVC/GI/GM specials

SA0002) Supplying and fixing of porcelin wash hand basin (white without pedastal), superior variety of size 550x400mm with all accessories

MS0050) Supply & fixing of CI Steps (not less then 5 Kg each)

SAMP0006) Supplying and fixing 150mm x 100mm size stone ware Gully trap with iron gratings over a bed of 150mm thick brick jelly concrete in CC 1:8:16 (one of cement, eight of crushed stone sand and sixteen of broken brick jelly) using 40mm size brick jelly and brick masonry wall 110 mm thick using kiln burnt country bricks of size 8¾”x4¼”x2¾” (22x11x7cm) in cm 1:5 (One of cement and five of crushed stone sand) plastered with CM 1:3 (One of cement and three of crushed stone sand) 12mm thick including Mortar Plasticizer (Liquid) at 200ml per bag etc., complete and as directed by the departmental officers.

WS0007) Supplying, laying and fixing of 20 mm dia GI Pipe ‘B’ Class of best approved quality for Hot water line fully concealed in walls

SAMP0003) Supplying and fixing of PVC Nahani Trap not less than 75mm 4 way / 2 way (Superior variety) having minimum of water seal of 50mm confirm to relevant I.S. specifications with its latest amendments including resting on the bed of brick jelly concrete 1:5:10 (One of cement, five of crushed stone sand and ten of 40 mm gauge brick jelly) including Mortar Plasticizer (Liquid) at 200ml per bag etc., complete

SA0033) Supplying and fixing of PVC SWR pipe (Soil line) with ISI mark - type 'B'. a) 110mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

b) 75mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

SA0035) Supplying, laying and concealing the 50mm dia PVC (SWR) pipe with ISI mark confirmed to IS 13952-1992 Type-B for waste water line

SA0036) Supplying and fixing of PVC (SWR) pipe with ISI mark - type 'A' for Ventilating shaft with cowl a) 110mm dia PVC SWR pipe of 3m with required PVC cowl & PVC specials etc.,

SA0048) Supplying, laying and jointing the following dia UPVC Non Pressure pipe of SN8 SDR 34 (S 16.5) as per IS 15328/2003 a) 110 mm dia UPVC Non Pressure pipe

b) 160 mm dia UPVC Non Pressure pipe

e) 4 core 16 Sqmm Brass cable gland

EL0229) Supplying and fixing 3 nos of 100 amps 500 volts grade porcelain fuse unit on suitable teakwood plank varnished to be fixed on the top of pole/EB street pole with necessary clamps including cost of all materials etc., all complete.

SA0047) Supplying and laying and loose jointing the following dia stone ware pipes with ISI mark Superior variety (glazed) with spigot and sockets ends in dry conditions and tested with water, after the pipes are laid to proper gradient to the alignment etc., complete and as directed by the departmental officers. a) 100mm dia

WS0281) Supplying & fixing of CPVC pipes confirming to IS 15778:2007 ASTM D-2846 standard including all CPVC fittings like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc. making holes, including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CC or CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors. a) 20mm dia CPVC pipe

SA0025) Supplying and fixing EWC superior variety (white) 500mm with 'P' or 'S' trap (Using crushed stone sand) (including Mortar Plasticizer (Liquid) at 200ml per bag)

In Ground Floor

SAMP0005) Supplying and fixing of Indian Water Closet white glazed (oriya type) of size 580 mm x 440 mm of approved make with ISI mark (to be got approved from EE before use) with PVC SWR grade 'P' or 'S' trap (Using crushed stone sand) (including Mortar Plasticizer (Liquid) at 200ml per bag) (Other than ground floor)

MS0003) Supplying and fixing of Aluminium Towel Rail of 75cm long

MS0006) Supplying and fixing of Aluminium plate with five pin for Coat Stand

MS0007) Providing and fixing iron Chromium plated 8 gauge Picture hook

MS0053) Supplying and fixing of C.I man hole cover with locking arrangements of approved quality and brand of size 0.6m x 0.6m (50Kg) as per standard specifications including cost of material, labour charges for fixing etc., all complete and as directed by the departmental officers.

L0001) Supply and planting Avenue Trees

L0004) Supplying and fixing of Triangular shape chicken mesh Tree guard

SA0053) Supplying and fixing of following dia PVC Tee b) 160mm dia PVC Tee

MS0008) Supplying and fixing of Bevelled Edge Mirror of approved quality and brand of size 500x400x5.5mm shelf type

NL0002) Supplying Fabrication and Erection in position of M.S. scheme name and layout board

b) Light point with bakelite battern type holder

c) Point wiring for calling bell/buzzer with push type switch with required Buzzer.

EL0010) Wiring with 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable for Fan Point

EL0018) Wiring with 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable for Stair case light point

EL0026) Wiring with 1.5 sqmm copper PVC insulated unsheathed single core 1.1 K.V. grade cable for 5 Amps 5 Pin plug Socket Point @ Switch Board Itself

EL0034) Wiring with 1.5 sqmm copper PVC insulated unsheathed single core 1.1 KV grade cable for 5 Amps 5 pin Plug Socket Point at Convenient Places

EL0041) Supplying and fixing 15 Amps 3 pin plug type socket with switch

EL0214) Earthing and Earth connections: Providing Earthing Station using pipe electrode as per IS 3043 using 2.5m of 40mm and 1.0m of 20mm B-class GI pipe including all requirements

EL0074) Supply and fixing of best approved superior variety concealed type Fibre box with M.S. Fan Hook

EL0075) Charges for assembling and fixing of ceiling fan of different sweep with necessary connections and fixing of fan regulator

EL0002) Wiring with 1.5 sqmm PVC insulated single core multistrand fire retardant flexible copper cable with ISI mark confirming to IS 694/1990 1.1 K.V. grade cable a) Light point with ceiling rose

b) 600mm x 600mm

EL0078) Supply and delivery of following Electric Ceiling fan with ISI mark with blades and double ball bearing, capacitor,etc., complete a) 48"" Electric fan 1200mm sweep

EL0070) Supplying & fixing of LED bulbs suitable for fixing it to pendent / bakelite battern holder of best approved variety etc., all complete and as directed by the departmental officers. a) 9 watts LED bulb

EL0047) Supplying and fixing of 4'18 watts crystal LED tube light and fixing the tube light fittings

SA0070) Supply and delivery at site and fixing of SFRC manhole cover with frame and locking arrangements a) 300mm x 300mm

EL0085) Supplying and fixing of 225 mm dia sweep AC exhaust fan of approved ISI quality

EL0045) Supplying and fixing of water tight Bulk head fitting suitable for 12W LED bulb with guard

EL0190) Run of main with 2 wires of 2.5 sq.mm. PVC insulated single core multi strand fire retardant flexible copper cable

EL0191) Supply and Run off main with 2 wires of 4 sq.mm. PVC insulated single core multi strand fire retardant flexible copper cable

EL0312) Supply and fixing of 6 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 No 63 A 4P MCB Isolator as incoming and 18 Nos 6A to 32A SP MCB as outgoing on wall with Earth connection only.

EL0100.a) Supplying and fixing of 25 watts LED bulb with Street light fittings arrangements

b) 12 watts LED bulb

EL0237) S & F of 450 x 375 x 20mm thick TW plank

EL0185) Run of main with 2 wires of 1.5 sq.mm. PVC insulated single core multi strand fire retardant flexible copper cable

EL0165) Supply and fixing of 63 amps triple pole main switch with fuse and neutral link on a suitable well varnished teak wood board including necessary interconnection and earth connection cost of all materials etc., all complete and as directed by the departmental officers.

EL0549) Labour charges for laying of PVC Aluminium Armoured LTUG cable excluding Civil works Below Ground level

EL0174) Supplying and run of 8 SWG GI wire for earth connection on wall / below ground level

WS0021) Supply and laying of following dia G.I "B" class pipes Above ground level a) 25mm dia GI Pipe

WS0018.XIII.c) Supplying and fixing of the 150mm dia MS Borewell clamp set

EL0337) Supplying and delivery of following PVC aluminium armoured LTUG cable f) 3.5 core 25 Sqmm PVC aluminium armoured LTUG cable

j) 3.5 core 95 Sqmm PVC aluminium armoured LTUG cable

s) 4 core 16 Sqmm PVC aluminium armoured LTUG cable

WS0004.c) Supply and errection of Rotational Moulded Polyethylene water storage tanks (HDPE Cylinderical vertical type) for outdoor use having capacity of 1000 litres (excluding free board) of approved brand (superior variety) with ISI Mark (marked with tank itself) with top lid

WS0107) Supplying and fixing of 32mm dia PVC Tee with end cap

MS0002) Supplying and fixing of 20mm dia aluminium hanger rods to the required length

SA0052) Supplying and fixing of following dia PVC Bend b) 160mm dia PVC Bend

LPS0024.d) Supply, installation, testing & commissioning of Conventional type Lightning protection system with complete set like Air termination, 8mm Aluminium rod, adhesion glude. cross connector, Metal roof conductor holder, down coductor, Test Joint, Stainless Steel Clamping, counter, mounting pole, test terminal box, earthing, earth pit, 10 mm copper bonded Round steel solid Conductor, If any necessary items is required etc as per the site condition shall be added. (Note: Refer enclosure drawing) (Conventional type) as directed by the departmental officers and the brand should be got approval.

CS0037) Supplying and fixing of precast cement concrete slab for cupboard/ ward robes, shelves, cover slab for chambers, baffle walls etc., and other similar works 40mm thick using standardised concrete mix M20 II. 40mm thick a) In Foundation and Basement

FLMP0021.I) Supply and fixing of GRANITE TILED FLOORING (Superfine Polished with Machine Cut Edges) of size 2'0 x 1'0 or 1'0 x 1'0 or 1'0 x 0'6 of 10 mm thick (Jet black) using grout joint, laid over CM 1:3 (One of cement and three of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with Grout, curing, finishing etc., all complete and as directed by the departmental officers. (Quality should be got approved from the Executive Engineer before use). a. In Ground Floor

FL0107) Supplying and fixing of PVC trims / Corners beeding suitable colour in toilet wall cladding in all floors including cost of all materials, Labour charges for fixing in position, cutting the required size wherever necessary, finishing etc., all complete and as directed by the departmental officers. (The Material quality & brand should be got approved from the Executive Engineer before use).

EL0548) Labour charges for laying of PVC aluminium armoured LTUG cable on post and wall to make good Above Ground level

b) From 151m upto 180m depth ending below Ground level

c) From 181m upto 210m depth ending from Ground level

d) From 211m upto 240m depth ending from Ground level

EL0252) Supply and fixing of 20A Flush type Wall Socket, 20A DP MCB and 32A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug)

GR0053) Supplying and fixing in position of colour galvalume sheet of 0.47mm thick as ridge piece inclusive of overlap length labour charges and nuts, bolts etc., all complete and as directed by the departmental officers. (The quality and the brand of material should be got approved by the executive engineer before use)

WS0148) Supply and delivery of 150mm dia of PVC casing pipes a) 150mm dia PVC Pipe

WS0236) Drilling of (150mm) vertical bores in hard rock area to any required depth as desired by TNPHC officials including labour charges for grouting and inserting the casing pipe in the drilling hole etc., a) Upto 150m depth ending below Ground level

c) 65mm dia GI Pipe

F0040) Supplying and filling in foundation and basement with filling crushed stone sand

d) 900mm x 900mm

WS0240) Supply and delivery of PVC end cap suitable for 160mm dia PVC casing pipe of approved quality etc., all complete.r

f) From 271m upto 300m depth ending from Ground level

WS0266) Supplying and fixing of 5 HP three phase panel board D.O.L with two level guard and auto start

EL0349) Supply and delivery of 3 core 4 sq.mm flat type copper cable

e) From 241m upto 270m depth ending from Ground level

WS0243) Supplying of following dia UPVC Column pipe for borewell a) 32mm dia UPVC Column Pipe

WS0265) Supplying and fixing of 3 HP three phase panel board D.O.L with two level guard and auto start

SA0139.d) Supplying and fixing of CP wall mixture Tap 3 in 1 system with Head showers

WS0162) Labour charges for the erection of three phase submersible pumpset in borewell / openwell Upto 5 HP

b) 50mm dia GI Pipe

WS0235) Supply and delivery of required dia nylon rope of best appred quality.

GR0059) Supplying, fabrication and fixing in position of mild steel angle truss including cost of materials and labour charges etc., all complete and as directed by the departmental officers.

EL0344) Supply and providing cable end termination of following core and sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete as directed by the departmental officers. f) 3.5 core 25 Sqmm LTUG Cable

EPS0016) Supply and erection of 125 Amps capacity floor mounting / wall mounting panel board (Cubical type) with bus bar chamber (For 16 in 1 Qtrs - 18 Services)

EPB0011) Supply and erection of 125 Amps capacity floor mounting / wall mounting panel board (Cubical type) with bus bar chamber (For 11 in 1 Qtrs, 13 services, 1 Block + common + 1 spare)

EPB0004) Supply and erection of 125 Amps capacity floor mounting / wall mounting panel board (Cubical type) with bus bar chamber (For 4 SI Qtrs, 6 services, 1 Block + common + 1 spare, 2 in 1)

EL0242) Supply and fixng of TNEB meter board suitablef or 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2"x1-1/2"x1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 63A fuse units (500V), 1No. neutral link, copper earth flat of size1"x1/4" with interconnection of EB meter to fuse units by 16Sq.mm PVC insulated copper wire with 1No 63Amp 30MA Four Pole RCD/RCCB(HigherEnd) with suitable necessary connection with earth connection complete.

WS0129) Supplying and fixing of best approved quality CP Angle cock

SA0155) Supplying and fixing CP Two way bib cock with health faucet

LF0022) Design, supply, Delivery, installation and commissioning of Passenger Lift (Without machine room) (Brand: Johnson / Kone / OTIS) of capacity 13 persons / 884 kgs as per the following specifications. 1. Type of Lift: Passenger 2. Load / Speed: 13 persons (884 Kgs) / 1m per second. 3. Drive: Micro Processor based VVVF 4. Travel / Pit : 14.20m / Pit 1600mm 5. Number of Floors: 4 (Stilt + 3 upper floors) 6. Floor Display Character: 0, 1, 2,3 7. Number of Landing Entrances: 4 (Stilt + 3 upper floors)

LF0020) Design, supply, Delivery, installation and commissioning of Passenger Lift (Without machine room) (Brand: Johnson / Kone / OTIS) of capacity 13 persons / 884 kgs as per the following specifications. 1. Type of Lift: Passenger 2. Load / Speed: 13 persons (884 Kgs) / 1m per second. 3. Drive: Micro Processor based VVVF 4. Travel / Pit : 11.35m / Pit 1600mm 5. Number of Floors: 3 (Stilt + 2 upper floors) 6. Floor Display Character: 0, 1, 2 7. Number of Landing Entrances: 3 (Stilt + 2 upper floors)

LF0019) Providing Vision Panel add per floor in Passenger Lift, Bed- Cum Passanger lift, Stretcher-cum-Passenger lift.

WS0018) Supply and fixing of following dia GI Specials of best approved quality,with ISI mark including cost and conveyence and fixing in position etc., all complete in all respects complying with relevant standard specification and as directed by the departmental officer (The brand and quality of the GI pipe should be got approved from EE before use). WS0018.X.a) 50mm dia GM Non Return valve

WS0018.VI.a) 50mm dia GI Union

32mm dia GI Coupling

WS0018.V.a) 50mm dia GI Elbow

WS0018.VII.c) 32mm dia GI Hex Nipple

WS0018.X.a) 32mm dia GM Non Return Valve

WS0018.V.c) 32mm dia GM Gate Value

WS0018.III.b) 50mm dia GI Bend

WS0018.III.c) 65mm dia GI Bend

WS0018.IV.b) 50mm dia GI Tee

50mm dia GI coupling

WS0018.IX.d) 50mm dia Gun Metal Gate valve

WS0018.V.c) 32mm dia GI Elbow

WS0018.I.d) 65mm dia GI Coupling

WS0280) Supplying and fixing of following dia UPVC specials of best approved quality including cost of specials and labour charges for fixing etc., all complete and as directed by the departmental officers. WS0280.III.a) 50mm dia UPVC Union

WS0279) Supply and delivery of 3 HP - Openwell Submersible pumpset with ISI mark suitable for Openwell q. 100 lpm x 50 m

WS0280.II.a) 50mm dia UPVC Tee

WS0280.I.a) 50mm dia UPVC Elbow

WS0280.IX.a) 50mm dia UPVC Hex Nipple

WS0280.I.c) 32mm dia UPVC Elbow

WS0280.III.c) 32mm dia UPVC Union

32mm dia UPVC Coupling

WS0280.X.c) 32mm dia UPVC MTA

WS0280.IX.c) 32mm dia UPVC FTA

WS0280.X.a) 50mm dia UPVC MTA

WS0280.XI.a) 50mm dia UPVC FTA

WS0151.a) Supplying of 25 mm dia PVC pipes 10 Kg/cm² including all specials etc., completed for casing pipes for 4.0 sq mm submersible flat cable and as directed by the departmental officers.

WS0280.VIII.a) 50X32mm dia UPVC Reducer Tee

WS0020) Labour charges for the GI and UPVC pipe below ground level including earth work excavation, cutting, threading, jointing, lowering, laying to proper grade and aligement and refilling the trench with excavated earth etc., all complete and as directed by the departmental officers. a) 25mm dia GI pipe

c) 32mm dia UPVC pipe

SA0114.a) Supply, delivery and fixing of Stainless steel sink of size 600mm x 600mm x 200mm thick

WS0234) Labour charges for the following dia PVC/UPVC pipe below ground level including earth work excavation, cutting, threading, jointing, lowering, laying to proper grade alignment and refilling the trench with excavated earth etc., all complete and as directed by the departmental officers. a) 50mm dia UPVC pipe

b) 65mm dia GI Pipe

WS0234) Labour charges for laying and jointing the PVC pipes as per 10 kg/ cm² etc., complete and as directed by the departmental officers. a) 25 mm dia PVC pipes

WS0270) Supplying and fixing of 32mm dia adopter (SS) for connecting submerssible pumpset with UPVC pipe etc., all complete.

CC0068) Design, manufacture, testing at works, transportation to site, unloading, storing, leading, erecting, testing & commissioning of Auto Power Factor Correction Relay (APFCR-50KVAr) suitable for 415Volts 3Phase 4wiresystem, fabricated from 14/16SWG CRCA sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted,modular type IP 42 Protection with powder coated panel , gland plates at top/bottom for control cables, complete with internal wiring, ferrules, name plates, painting, internal exhaust fans for cooling in every compartment etc.,

LPS0024.a) Designing, S I T & C of earth station as per IS 3043, with proper earth lead connection arrangements. Rate shall include all materials