PROVISION OF FIRE STATION AND FIRE HYDRANT SYSTEM AT MLC LC-IV DHAMRA

Amount

SUB HEAD-I - EARTH WORK Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge: All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Extra rates for quantities of works, executed: Note for Above items:- The extra percentage rate is applicable in respect of each item but limited to quantities of work executed in these difficult conditions. The unit, namely, metre depth, to be considered for payment, shall be the depth measured from the sub soil water level up to the centre of gravity of the qty executed in difficult conditions. The depth shall be reckoned correct to 0.10 m, 0.05 m or more shall be taken as 0.10 m and less than 0.05 m ignored. In or under water and/or liquid mud, including pumping out water as required

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

SUB HEAD-II - CONCRETE WORK Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.material in cement concrete per 50 kg

SUB HEAD-III - REINFORCED CEMENT CONCRETE Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Edges of slabs and breaks in floors and walls Under 20 cm wide

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Weather shade, Chajjas, corbels etc., including edges

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(Note :- Cement content considered in this item is @ 380 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

All works above plinth level upto floor V level

Extra for providing richer mixes at all floor levels Note:- Excess/less cement over the specified cement content used is payable /recoverable separately. Providing M-30 grade concrete instead of M-25 grade BMC/ RMC.(Note:- Cement content considered in M-30 is @ 400 kg/cum)

Add for using extra cement in the items of design mix over and above the specified cement content therein.

SUB HEAD-IV - BRICK WORK Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry As per IS 2185part-3 with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars and drilling the column/Existing wall and fixing 200mm long, 50 x 4mm thk. MS Flat, bent to shape with anchor bolts . Approved GI mesh shall be placed and tied in position between masonry and MS Flat, bent to shape, with anchor bolts at every third course of half brick masonry.

SUB HEAD-V- STONE WORK Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

SUB HEAD-VI- CLADDING WORK Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

SUB HEAD-VII - WOOD AND PVC WORK Extra for providing etched glass panes instead of ordinary float glass panes in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 100x10 mm

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading

SUB HEAD-VIII - STEEL WORK Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 80 mm

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of Required size, joints mitred and welded by angle iron flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.

SUB HEAD-IX - FLOORING Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick

Providing and fixing glass strips in joints of terrazo/ cement concrete floors 40 mm wide and 4 mm thick

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. 8mm thick Granite of any colour and shade

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete Size of Tile 600x600 mm

SUB HEAD-X - ROOFING Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Coupler 110 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

SUB HEAD-XI - FINISHING 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams

Extra for providing and mixing water proofing material in cement .Per bag plaster work in proportion recommended by the manufacturers

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

SUB HEAD-XII - ROAD WORK Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

"Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing 25mm dia dowel bars with sleeve @ 600mm c/c at joint, tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, tie bars to be paid separately). Cement concrete prepared with batch mixing machine

Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade 'A' sealing compound.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of engineerin- charge.

SUB HEAD-XIII - WATER SUPPLY & SANITARY INSTALLATIONS Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board610x460 mm bowl depth 200 mm

Providing and fixing white vitreous china wall mounting water closet of size 570x340x360 mm of approved shape including providing & fixing PVC concealed cistern of Size 460x450x80mm with dual flush plate fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc including painting of fittings and cutting and making good the walls and floors wherever required : complete.make Hindware cat Nos-92097

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :

Providing and fixing oval shape counter top wash basin with 450mm Long Braided Hoses 32 mm C.P. brass waste of standard pattern, including necessary fittings and brackets, cutting and making good wherever required White Vitreous China oval shape counter top Wash basin size 550x430 mm(make parryware C0466(sp)/444) with a 15 mm CP Brass single hole basin mixer

Providing and fixing towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and .600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm. make JAQUAR ACN-1111N or eqv.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineerin- charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing soil, waste and vent pipes : 100 mm dia Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

Providing and fixing soap Dish Holder with concealed fitting arrangements.Make Jaquar ACN-1131N or eqv.

Providing & fixing CP brass Health faucet with PVC Flexible Tube with wall hook.( JAQUAR MODEL NO-573 or Equilent.)

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing terminal guard : 100 mm Sand cast iron S&S as per IS - 3989

Providing and fixing unplasticised Polyvinyl Chloride (UPVC) pipes, having thermal stability for hot & cold sewage supply including all UPVC plain fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, & testing of joints complete as per direction of Engineer in Charge.Toilet Sanitary pipe work 100 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 25 mm dia nominal bore

32 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 25 mm diameter pipe

32 mm diameter pipe

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

Providing and fixing C.P. brass long body Two Way bib cock of approved quality conforming to IS standards . 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

SUB HEAD-XIV - DRAINAGE Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 150 mm diameter S.W. pipe

300 mm dia. R.C.C. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : Size 90x80 cm With common burnt clay F.P.S. (non modular) ricks of class designation 7.5

Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality M D - 10 Square shape 450 mm internal dimension

H D - 20 Circular shape 560 mm internal diameter

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

SUB HEAD-XV - PILE WORK Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 400 mm dia piles

450 mm dia piles

Extra over single under ream for providing additional bulbs in under reamed piles, under specified diameter(only the nos. of extra bulbs are to be paid) 400 mm dia piles

450 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. Single pile upto 50 tonne Safe capacity Initial test (Test Load 2.5 times the Safe capacity)

Routine test (Test Load 1.5 times the Safe capacity)

SUB HEAD-XVI-ALUMINIUM WORK Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings, the directions of Engineer-in-charge and details adhering to approved shop drawing, submitted by the contractor. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing including the cost hinges/ pivots, in-built roller track, uPVC extruded interlocks, wool pile, zinc alloy touch locks with hook, zinc alloy body with single nylon rollers (required weight bearing capacity ) and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

SUB HEAD-XVII - WATER PROOFING Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Surface preparation:-Cleaning of RCC roof by removal of dust ,dirt,laitance,following by ponding will be done on the applicotion surface. Any surface cracks needs to be into U groove and sealing it with polymerin 1:4 ratio (cement: sand)admixed with Dr Fixit pidicrete URP at 5% byweight of cemen . All corner joints will be cut open, followed by sealing the same with the same polymer mortor all in compllete. Cemen ,sand, aggregate,water will be supplied by contractor.providing and applying "Dr Fixit Flexi PU 270(i) high performance pure root , seamless, waterproof memberance,appliedin 2 coats of totol Systems thickness of 1.50 mm and having an elangation capacity of over 500% , tensil strength of 4 N/mm2 .and the coating will be terminated up to 300 mm on theparapet wall, all in complete. providing and laying 120-150 gsm geotextile on the cured memberane surface providing and laying protective screed concrete (M20 grade ) with admixture of recomanded propertion and average 50 mm thick(thickness can varydepending up on span of area ) . All in complete (including welded mesh 2mm dia and 100mmX100mm aparture but M-20 Grade sceed will be paid separately)

Waterproofing of HorizontalSurface Horizontal Areas (Below Raft): Supplying and installing Dr.Fixit Prebond - 1.2mm thick self-adhesive HDPE membrane having the following technical properties-Puncture resistance 1000 N (as per ASTM E 154) ,Tensile strength of 25 Mpa as per ASTM D412,Elonagtion of >500% as per ASTM D 412, Resistance to hydrostatic head > 60M as per ASTM D 5385,Peel adhesion to concrete 880N/m as per ASTMD903. The system should be fully bonded to the RCC and consists of highly resilient HDPE layer, a pressure sensitive adhesive layer which is covered by a weather proof protective layer. The membrane shall have minimum of 100 mm side and end laps which shall be sealed with double sided adhesive tape. The size of the membrane should not be less than 2.4Mtr. x 20 Mtr. to minimize the joints and the entire waterproofing treatment should be guaranteed by the principal manufacturer as a system, for ten years, materials, labours, tools, tackles, etc., complete.

Waterproofing of Vertical Surface Vertical Surface (Retaining wall): Providing and laying of 1.5 mm thick Dr.Fixit Samshield XL- SBS based self-adhesive waterproofing membrane topped with hdpe cross laminated Valeron film with the following technical properties-Elongation of >200 % as per ASTM D882, puncture resistance of >200 N as per ASTM E154 including cleaning the surface,priming the surface with cold applied bituminous primer@4-6 sqmtr/litre, properly sealing the joints & maintaining 75 mm overlap between the membrane selvedge & 100 mm overlap on the end joints of the membrane over the slab etc. complete.

Providing & Fixing of protection board 8MM – HDPE Dimple board spot bonded on retaining wall before backfilling.

Providing aluminum flashing, wherever required for termination of Dr. Fixit Samshield XL 1500 membrane at all locations. Item shall include rates for membrane termination on the Vertical retaining wall at height as specified in drawings for termination of the membrane and finally sealing the strip using Dr. Fixit Pidiseal , Polysulphide sealant.Providing aluminum flashing, wherever required for termination of Dr. Fixit Samshield XL 1500 membrane at all locations. Item shall include rates for membrane termination on the Vertical retaining wall at height as specified in drawings for termination of the membrane and finally sealing the strip using Dr. Fixit Pidiseal , Polysulphide sealant. Providing and applying Dr. Fixit Fastflex, a two component polymer based cementitious waterproofing system in following sequence; Cleaning the internal surface areas thoroughly so that they are free of all contaminants like dirt and laitance & to remove all the loose materials by various mechanical means. Removal of all surface imperfections, protrusions,loose concrete & filling of cracks using Dr Fixit Pidicrete URP Modified Mortar in the ratio Cement: Sand (1:4) and 5% by weight of cement. Providing and making fillets at the junction of the walls and the slabs using cement mortar of 1:4 mix admixed with 5 % of DR. FIXIT URP by weight of cement. Applying 3 coats of Dr. Fixit Fastflex(2 component, prepacked,polymer modified cementitious coating)@ 3kg/sq.mtr all over the slab including the angular fillets and extendable over the vertical walls .Finally sprinkling sand over the third coat for better adhesion with plaster. The interval between each coat of Fastflex application is 6-8 hrs.

Providing & laying a protection layer of 25 mm thick cement mortar admixed with Dr. Fixit Pidiproof LW+

SUB HEAD-XVIII - FURNITURE Providing Single Bed of basic Size 75"(L) x36"(w) x14"(height under the bed) with head panel of height 30" and leg side panel of 18"height. Main frame of head panel made of 1st class CP teak wood of section 4"(including 1/2" beading) x 1 1/4"(thick,) with central panel made in 8mm thick anti termite and water proof Plywood (Duro/ Uniply make) pasted with 1mm laminate (merino/ formica/ greenply make) as approved. Leg side panel made in first class teak wood section of 4"(including 1/2" beading x 1 1/4"(thick.) with interconnecting member of 2" x 1 1/4"(thick.) in first class teak wood. Internal panel to be of 8mm ply (duro make) pasted with 1 mm thick. laminate (merino/ formica/ greenply make) as approved using standard adhesive and any other necessary fixing arrangement .The main side supporting members to be made in first class teak wood of section 3 3/4" x 1 1/4" with a inset of 15mm for inserting 12 mm ply over it forming the base of bed for mattress. Side members to be interconnected with 4 nos Hollock/Mirandi wood battens of section 2" x 1 1/4" placed at equal distance along the length of bed. Bed Top shall be made up of 12 mm thick commercial alternate core ply (anti termite and water proof) of Duro/ Uniply make, fixed into the inset of side battens and on to the equally placed Hollock/Mirandi wood members, fixed using suitable screws etc. all complete. All the exposed teak wood parts as well as any other part of wood/ board/ ply, shall be melamine polished (matte) to a shade as approved by Engineer-in-charge. All the joints between teak wood members shall be dove tail joints reinforced with bamboo nails, and polished and finished after due process of filing and filling with approved fillers to get a neat and smooth finish. All the teak wood/ any other wood used shall be well seasoned and free from knots and any other defefcts.

Providing and placing in position office Table for clarck of size: 1219.2mm x 609.6mm x 762mm havinig wooden top round tube under structure with three drawer unit make Godrej modal table T-111 or EQV.

Providng & placing in position Chair of size 600w x 625D x 875 H mm. the seat & back made from 12mm thick hot pressed plywood and upholsterd with frabic and moulded polyurethane foam. The back foam is designed with contoured lumber support for extra comfort. the seat size: 470W x 480D mm and back size 470mm W x 580mm H . The HR polyurethane foam is moulded with density of 45+/-2kg per meter cube and hardness load of 16 +/-2kgf as per IS 7888 for 25% compression. The Armerest should be of one-piece armrest are fitted to the seat are injection moulded black copolymemer. there should be a synchrnous tilt mechanism designed. the ped should be injection in black 30% glass-filled nylone and with 5 twin wheel castore in injection moulded type of black nylon. the ped of 660mm +/- 5mm pitch-center dia. approved make: Godrej Modal BRAVO or eqv. as approved by Engineer-in-charge

Supplying and placing in position Three Seater Steel chair of size 1630x570x675mm made of back powder coated rectangular MS ERW tube having 80x40x2mm size. Chrome plated made of cold rolled steel with 1.2mm thick Legs and arms.Powder coated perforated shell made from cold MS sheet DIN1623 part1 st12grade 1.4mm thick Seat and back. The side bar is made of chrome plated solid 30x12mm with fluting and plastic inserts the shell is assembled on the cross beam with help of M8 bolts. Make Godrej Product NANO PERCH

Providng & placing in position Desk Table of Size (1000Lx500Wx750Hmm) Made of 15 mm thick MDF board with melamine finish. including Keyboard tray & shelves for CPU, UPS, printer etc.with Drawer including all necessary hardware fittings & locking system complete. Make NILKAMAL Modal AUSTIN or Eqv.

Supply of shelves with glass shutter f size 900x1200x225mm made out of 19mm thick one side teak board having 2No. Shelves, back with 6mm thick commerical ply provided with 4mm thick plain glass sliding shutters with 'E' aluminium channel edges to have teak wood lipping all exposed surface finished with melamine polish etc. all complete as directed/approved by the Engineer-in-charge.

Providing and placing in position Steel Almirah of outer size 1981.2 X 914.4 X 482.6 mm made of machine pressed steel sheet and powder coated in a shade as approved by Engineer-in-charge. Internal Size of Almirah: 1850 (H) X 900 (W) X 450 (D) mm. Leg Size of Almirah: 150 (H) X 120 (W) X 450 (D) mm. Rack with 5 Compartments of 4 no. of shelves. Distance between each shelf will be 360 mm. These shelves should be hanging arrangement (adjustable). Standard lock and 2 sets of keys. The thickness of the Almirah sheet shall be 18 SWG. The body of the Almirah shall be manufactured from cold rolled MS sheet (C. R. Sheet) with Antirust treatment and shall be finished with powder coating. The quality of used M.S sheet for making Almirah shall be free from any pitting and corrosion etc. H/D Rubber bushes shall be provided to the bottom of legs of Almirah. . Make Godrej, Delite, Steelcase, Methodax .

Providing and fixing 100mm vertical blinds of approved colour made from 100% polyester yarn coated with fade resistant polymer to ensure complete opaquely with zero light transmittance having suitable coating on exterior, including all fixtures and fittings complete in all respect as per design and instructions of the Engineer-in-charge

Providing and placing in position Steel Almirah of outer size 1270X 838.2 X 431.8 mm made of machine pressed steel sheet and powder coated in a shade as approved by Engineer-in-charge. Internal Size of Almirah: 1100 (H) X 900 (W) X 450 (D) mm. Leg Size of Almirah: 150 (H) X 120 (W) X 450 (D) mm. Rack with 4 Compartments of 3 no. of shelves. Distance between each shelf will be 260 mm. These shelves should be hanging arrangement (adjustable). Standard lock and 2 sets of keys. The thickness of the Almirah sheet shall be 18 SWG. The body of the Almirah shall be manufactured from cold rolled MS sheet (C. R. Sheet) with Antirust treatment and shall be finished with powder coating. The quality of used M.S sheet for making Almirah shall be free from any pitting and corrosion etc. H/D Rubber bushes shall be provided to the bottom of legs of Almirah. Make Godrej, Delite, Steelcase, Methodax .

Supplying and placing in position of Sofa set 5 seater (3+2),3 Seater size 1700x770x780mm & 2 seater size 1270x770x780mm make Godrej Modal Micro Plusor product code:STSFMPP2019/STSFMPP3019 eqv. as approved by Engineer-in-charge

Providng & placing in position Peg table of size 450X450X450mm. made up of teak wood frame, finished with melamine polish & table top to be of 12 mm thick toughened Glass with beveled edge, All round Supported on teak wood frame the finishing of table should be smooth finish with melamine polish to get desired smooth effect. the wood should be free from Knots, complete as per direction of Engineer-in-charge

Providng & placing in position center table of size 1100 x 600 x450 mm ,made stainless steel frame with glass top as per manufacturer specification make Neelkamal Modal BRADYor eqv. as approved by Engineer-in-charge

Providing and placing in position Revolving office Chair of Size 640w x630D x970H mm .The seat & back made 1.2cm thick hot pressed plywood and upholstered with frabic and moulded polyurethane foam. the back foam is deigned with contoured lumber support for extra comfort, make NILKAMAL Modal no.THAMES LOW BACK FABRIC OFFICE CHAIR or Eqv.

Providing and placing in position Steel BOX of outer size 600 X 400 X 600 mm made of machine pressed steel sheet and powder coated in a shade as approved by Engineer-in-charge. A slit opening of size 25mm x 300mm is to be provided at the top of the box and openable sutter of size 450x4500mm is to be provided at the front of the box . Standard lock and 2 sets of keys. The thickness of the box sheet shall be 18 SWG. The body of the box shall be manufactured from cold rolled MS sheet (C. R. Sheet) with Antirust treatment and shall be finished with powder coating. The quality of used M.S sheet for making box shall be free from any pitting and corrosion etc. H/D Rubber bushes shall be provided to the bottom of legs of box. Note.:- All FURNITURE product shall be delivered at site duly covered with bubble sheet to avoid any breakage etc. However in case of any minor repair arising out of transportation etc. the same shall be repaired/replaced immediately by the supplier without any extra cost.

SUB HEAD- XIX-INTERNAL ELECTRIFICATION LIGHT POINT WRING Point wiring for Light / fan / Exhaust fan with 2 runs of 1100V grade 1.5 sq. mm & 1 run of 1.5 sq. mm FRLS insulated multistranded Copper wires, run in & including 25 mm dia , medium class PVC conduit concealed in wall after necessary chase cutting with finishing / surface on wall/ ceiling conforming to IS 732 including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI switch box with modular switch and the box covered with front plate. One Light point controlled by one 6A switch ).

Two Light point controlled by one 6A switch ).

Exhaust fan point controlled by one 6A switch including ceiling Rose.

One ceiling fan point controlled by one 6A switch With 100W step type Electronic regulator including Concealed MS fan hook box.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class 25mm dia PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

6A SWITCH & SOCKET Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.(Independent)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.(dependent)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed 25mm medium class PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4X 2.5 sq. mm + 2X 2.5 sq. mm earth wire

Light Fixtures Supply, Installation, Testing & Commissioning of the following Light Fixture with lamp, Control Gear & All necessary accessories. Luminaries with all electrical accessories & it should be energy efficient, low loss, ortho cyclically wound open construction copper ballast, ignitor & power factor improvement capacitor or Electronics Ballast etc are prewired up to the terminal block & mounted on a removable control gear module for ease of maintenance. All electrical connections of the control gear module with the rest of the luminaries should be click fix & require use of no tools. Mounting options should be for both lateral as well as pole top mounting. with Lamp Control Gear & Fixing Accessories. 10W LED surface mounted DOWNLIGHT MAKE-PHILLIPS CAT NO.DN092B LED10S-6500 PSU WH

33W LED RECESSED MOUNTED LUMINAIRES MAKE-PHILLIPS CAT NO. RC380B LED30S 6500 L60W60 PSU OD S1

Philips 38w, Suspended-Surface Mounted Luminaires Cirrus Series, SM365C LED33-6500 PSU-OD WH

20W LED SURFACE MOUNTED MAKE-PHILLIPS CAT NO. SM200C LED16S 6500 OD WH

20W LED BATTEN LIGHT WALL/SURFACE MOUNTED MAKE-PHILLIPS CAT NO. BN108C 20S PSU CDL WH

Philips 31167 Mirror Light 11W Wall Light (Warm White Light) B074K8X8XY

16W LED SURFACE MOUNTED Downlighter MAKE-PHILLIPS CAT NO. DN394B LED16S-6500 PSR-P WH

10W BULKHEAD LIGHT MAKE-PHILLIPS CAT NO. WT202W LED6S NW PSU S2 PC

FANS/EXHAUST FANS Supplying, Installation, testing and commissioning of ceiling fan of 1200mm sweep suitable for operation on 230/240V, 50Hz, single phase, AC Supply complete with double ball bearing motor, of ceiling fan, including required down rod length with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including phenolic laminated sheet cover on the fan box etc. as required.

Supply, Installation & testing of following 900 RPM Exhaust fan suitable for suitable for single phase 230/240V, AC Supply complete with motor MS louvers , mounting brackets, all accessories etc as complete. 305 mm dia 900 rpm metal body exhaust fan (Heavy Duty)

POWER POINT WRING Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

CIRCUIT/SUBMAIN WIRING Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 10 sq. mm earth wire

DISTRITUTION BOARD Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB /RCCB /Isolator) 6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing following rating, double pole, 240 V,isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling hole in cubicle panel, making connections, etc. as required. 125 A, 16 KA,TPMCCB

SUB HEAD- XX- AC SYSTEM Supply, installation, testing and commissioning of Hi wall Air Cooled 2 Ton split unit 5 STAR Ratings.The unit shall be complete with all Essential acessories, including indoor, outdoor unit & stand for outdoor unit complete with all respects.

Supply, installation, testing and commissioning of AC SINGLE PHASE 5KVA Automatic operation having input voltage 170 to 270 Volt and output voltage 240v. Complete with voltmeter, high and low voltage cut off & time Delay relay type digital voltmeter Stabilizer.

Supply .Fixing and testing of 20 mm dia. PVC condensate drain piping with insulation of 6 mm thick nitrile rubber including wall cutting ,chasing of wall etc complete in all respects.

Supply, Laying, testing and commissioning of copper refrigerant piping ,15.9 mm dia dia, duly insulated with 13 mm thick insulation pre-formed moulded sections of closed cell XLPE insulation of class 'O' fire rating having uniform density not less than 25 kg/cum, including cutting, chasing, PVC Casing Caping of required Size & necessary accessories etc as complete in all respect. Note:- quantity shall be consider beyond 3 mtr.

Supplying , installation, testing and commissioning of copper cable of 2.5 sqmm x 3 core PVC insulated, including cutting, chasing, PVC Casing Caping of required Size & necessary accessories etc as complete in all respect.

SUB HEAD-XXI TELEPHONE AND DATA SYSTEM Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc.as required. 1 or 2 Module (75mmX75mm)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Providing, fixing connecting and testing of under noted size of solderless telephone tag block Connector in surface/recess in wall required size of M.S. box with hinged lockable cover duly stove enamel painted. 10 Pair Tag Block

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet (RJ11)

Supplying and fixing of modular type Lan (RJ-45) outlet in existing Box complete as required. Computer socket outlet (RJ 45)

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

SUB HEAD-XXII- EARTHING SYSTEM Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 8 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

SUB HEAD-XXIII- MISCELLANEOUS ITEMS (b) Water Cooler with Ro System Aquaguard Purechill RO 80 PSS (Eureka Forbes Providing seven stage water purification , the new Aquaguard PureChill RO Storage Cooler cum Purifier with its one of a kind purification technology (RO), with cooling and storage solution of following specification. Approximate External Dimension (W XD XH) 640 x 450x 1350 mm Operating Power Supply 230 (+- 10% V AC, 50 Hz b) Fliter Cartridges - Sediment, Activated Carbon, Carbon Block Running Current in Amps.(Max) 4.5 + 10 %, Power in watts (Max), 700+- 10%, water storage Tank Capacity 80Ltr.

CABLE WORK Supplying Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. 95 Sqmm x 3.5 core (1100 volt grade XLPE insulated, PVC inner sheated, galvanised steel strip or wire armoured cable as per IS 7098(PART 1)1988)

70 Sqmm x 3.5 core (1100 volt grade XLPE insulated, PVC inner sheated, galvanised steel strip or wire armoured cable as per IS 7098(PART 1)1988)

4core16 Sqmm (1100 volt grade XLPE insulated, PVC inner sheated, galvanised steel strip or wire armoured cable as per IS 7098(PART 1)1988)

4core 6 Sqmm (1100 volt grade XLPE insulated, PVC inner sheated, galvanised steel strip or wire armoured cable as per IS 7098(PART 1)1988)

CABLE END TERMINATION Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 95 sq. mm (45mm)

3½ X 70 sq. mm (38mm)

4 X 16 sq. mm (28mm)

Area Lighting Supplying of MS steel tubular pole welded Swaged type complete of :- SIZE :- 114.3 X 88.9 X 76.1mm WALL THICKNESS 3.65 X 3.25 X 3.25MM SECTIONAL LENGTH :- 5 + 2 + 2 MTRS. TOTAL HEIGHT :- 9 MTRS. Long with SOH 1500 mm made out of 48 mm dia pipe with a canopy of 300 mm complete M.S.BASE PLATE :- 300 X 300 X 6MM NOTE ;-PCC shall be measured and paid for separately

Supply and fixing of 70W 5700KLED streetlight made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07. (HAVELLS 70W LHETBXU7PA6J070)

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 8.0 meter and upto 10.0 meter

Providing and making MS steel pole collar with cement concrete (1 cement : 3 coarse sand : 6 stone aggregate 20 mm) of specified size and shape including form work, plastering if required, curing etc. as required. (volume of pole/ pipe not to be deducted)

(SHEET MOULDED COMPOUND) junction box size 200mm x 140mm x95mm as per IS: 13410 & IS:14722 completed with door, hinger and locking arrangement ,including one no. 6 amps MCB SP, AL busbar (TPN) , stainless steel terminal, MCB channel , with clamp for fixing with pole.

Providing spiral coil earthing with 8 SWG G.I wire including spreading os salt and charcoal as per IS: 3043-87 with lastest ammendments.

3core 6 Sqmm (1100 volt grade XLPE insulated, PVC inner sheated, galvanised steel strip or wire armoured cable as per IS 7098(PART 1)1988)

Providing and fixing 8 SWG dia G.I. Wire on surfaces or in recess for loop earthing along with existing surfaces /recessed conduit/submain wiring/cable as requried

Wiring for street Light fitting from junction box to street light fitting with ( 2x 2.5 sqmm copper conductor, 11kv grade, PVC insulaed, unsheathed single core cable in surface/ recessed as required.

Special Items of Work SUB HEAD- XXV- FIRE HYDRANT SYSTEM Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP Squirrel cage induction motor, TEFC,synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered with anti vibration pads. 2850 lpm at 70 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS :325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 70 m Head

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

100 mm dia

150 mm dia

200 mm dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :- 2 way-100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 450 mm dia, 8mm thick MS sheet, 2000 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K - 9 conforming to IS : 8329 :with two coats of anti-corrosive bitumastic paint of approved quality and filling sand of grading zone V or coarser grade, allround the pipes, trenching, refilling & testing of joints complete as per relevant IS code & direction of Engineer in charge. 150 mm dia Ductile Iron Double Flanged

200 mm dia Ductile Iron Double Flanged

Providing and laying D.I. specials of class K-12 suitable for push-on jointing as per IS : 9523 : Up to 600 mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wetriser/ sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 80mm dia

150mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc.and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25mm dia

32mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm. dia

200 mm dia (wall thickness 6.3 mm)

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing and fixing gun metal ball valve suitable for pressure more than 15 Kg/Cm2 and confirming to IS: 778 of the following size including providing necessary union / flange etc all complete. 25 NB

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 40mm dia

80mm dia

100mm dia

150mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 80mm dia

150mm dia

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal / Stainless Steel cap and chain as required Single headed Gunmetal

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Supply and fixing of Fire Hose Box of Stainless Steel of size 3 ‘x 2' x I' 6” to accommodate two numbers of 30 M length hoses and branch pipe, glass fronted, double door with lock painted fire red outside with suitable structural support complete but excluding civil works.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 80mm dia

150mm dia

Supplying and fixing PCC route marker 150 mm dia cast iron disk bolted to 40x40x3mm angle iron grouted in 1:3:6 concrete block 150x150x300 mm deep including two coats of aluminium paint on metal work.

Providing and fixing following dia, 750 mm long hot dipped G.I. Puddle flanges for water tanks as per I.S. 1239 (Class C) with 6mm thick M.S. Plate of suitable size and welded all-round the pipe fixed in walls, beams and top slab of R.C.C tanks, etc. complete all as per the directions and to the satisfaction of Engineer-in-charge. 150 mm dia (Flanged ends MS plate 6 mm thick; 250 mm x 200 mm plus dia of pipe).

Over Head Filling Point for fire Tender- Providing and fixing gun metal ball valve suitable for pressure more than 15 Kg/Cm2 and confirming to IS: 778 of the following size including providing necessary union / flange etc all complete. 65 mm nominal bore

80 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 80 mm nominal bore Horizontal Horizontal

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (External work) 65 mm dia nominal bore

80mm dia Nominal Bore

Supply, laying and commissioning of following size 1.1KV grade XLPE insulated armoured aluminium conductor underground cable in built-up cable trench/already laid RCC hume pipe or on cable tray with all installation materials. The cable shall conform to IS 7098/Part I.Armoring shall be IS 7098 Part IB 4C x 16 Sqmm A2XFY

3.5C x 120 Sqmm-A2XFY

2C x4 Sqmm Copper

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4Cx 16 Sqmm

3½ X 120 sq. mm (45mm)

EARTHING (a) Copper Plate Earthing Station Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

(b) G.1 Plate Earthing Station Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required. 150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

MISCELLANEOUS ITEMS Supplying and placing of non-skid rubber mat suitable thickness confirming to IS- 15652 and 900 mm width as required including cutting to required lengths or approved make with test certificate for L.T panels.

Supplying and placing of non-skid rubber mat suitable thickness confirming to IS- 15652 and 900 mm width as required including cutting to required lengths or approved make with test certificate for H.T. 11-33 KV panels.

Supplying and fixing cable route marker with route indication on 150 mm dia cast iron disk bolted to 40x40x3mm angle iron grouted in 1:3:6 concrete block 150x150x300 mm deep including two coats of aluminium paint on metal work.

Supplying and fixing of shock restoration chart written in english and hindi duly framed in glass as required.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 450 mm dia. R.C.C. pipe

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab1:2:4 mix (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

RIC Projects Pvt. Ltd.

VASTU SHOBHA