REPAIR, POLISHING OF WOODEN FURNITURE (MAP) AND PAINTING OF STEEL FURNITURE (MAP) AND CONVERSION OF CHARPOY GI NYLON NIWAR TO GI PLY TOP UNDER BSO OF GE (NORTH) UDHAMPUR

Amount

SOFA SET 5 SEATER (FD/MAP-II/02) Taking down old unserviceable cover of cushion of sofa set and Supply and fix new covers with velvet/ tapestry cloth not less than Rs.450/- per metre, complete all as specified and shown on drg and directed.

Taking down old unserviceable cushion of sofa set and supply and fixing new foam cushions 40 density of size 22 "X 21" x 4" (Make :- Sleepwell/ Featherfoam/ Kurlon(top model) duly covered with velvet/ tapestry cloth not less than Rs. 450/- per metre, complete all as specified and shown on drg and directed. Drawing No. FD/MAP-II/ 02

Preparing the old surface and making smooth surfaces by rubbing with suitable emery paper, after sanding, wipe the surface with a clean, soft cloth to remove any sanding dust, than apply a thin coat of wood polish to a clean microfiber cloth or a polishing pad. Using circular motions are recommended to ensure even application and allow the polish to penetrate the wood effectively and create a lasting shine. Final touches once the first coat is applied, allowed it to dry completely before assessing the finish/ another coat. Ensure the final finish is smooth and glossy and as directed by the Engineer-in-Charge. Note :- To confirm the quality of the finish : To providing a surface with a high gloss shine GCI Wood Polish Thinner is used to dissolve Lakdhana or Shellac. Drawing No. FD/MAP-II/ 02

CHAIR DINING CUSHIONED (MAP) (FD/MAP-II/04(R) / FD/MAP/02) / (FD/MAP/10) Removing of unserviceable front leg from chair dining and S&F new approved quality seasoned 1st class teak wood leg to match other leg as existing pattern/ design/ polish and fix nylon buffers at bottom of all legs, complete all as specified and directed.

All as per serial item No. 4.00 here-in-above but rear leg.

All as per serial item No. 4.00 here-in-above but back batten.

All as per serial item No. 4.00 here-in-above but front/ rear/ side rail.

Additional of mentioned drawing 04 Nos of corners of size 75mm x 75mm x 20mm made up of 1st class teak wood shall be provided and fixed at right angle of legs and rails with chinese black screw for extra strength. All fittings/ material shall be as approved by GE/Engr-in-charge. Drawing No. FD/MAP-II/04) / FD/MAP/02) / (FD/MAP/10)

Taking down unserviceable cushion with plywood 12mm thick (Make : Century/ Greenply/ Kitply) of seat of chair dining cushioned (MAP) S&F new approved quality 75mm thick 40 density foam including covered with velvet/ tapestry cloth not less than Rs. 450/-per meter including 12mm thick plywood as size and shape of seat of existing chair, rest all as specified in drg and directred by Engr-in-Charge. Cushion make : Sleepwell/ Kurlon/ Featherfoam (Top Model) Drawing No. FD/MAP-II/04) / FD/MAP/02) / (FD/MAP/10)

Applying two coats of french polish to chair dinning cushioned (MAP) after smoothing surface by Emery paper. Final touches once the first coat is applied, allowed it to dry completely before assessing the finish/ another coat. Ensure the final finish is smooth and glossy and as directed by the Engineer-in-Charge and rest all as specifed on Drg. Note :- To confirm the quality of the finish : To providing a surface with a high gloss shine GCI Wood Polish Thinner is used to dissolve Lakdhana or Shellac. Drawing No. FD/MAP-II/04) / FD/MAP/02) / (FD/MAP/10)

TABLE BED SIDE MAP (FD/E6/MAP/07) / FD/E6/MAP-15(R)) Removing of old unserviceable shutter of table bed side and S&F of new shutter made of approved quality 18mm thick prelaminated MDF board (Century/ Greenply/ Kitply) as per the drg with suitable L Bihari hinges. The fixing shall be done with standard workmanship, complete all as specified in drg and as directed by Engr-in-charge.

Carefully detach the old existing unserviceable handle on the bedside table. Make sure to remove all screws or fastenings without damaging the surface or structure of the bed side table and S&F of stainless steel new handle 50mm wide including accessories for fixing of superior quality as per the drg. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/E6/MAP/07 / FD/E6/MAP-15(R)

Removing of old unserviceable drawer and telescopic channel of table bed side (MAP) and S&F of new drawer made of approved quality MDF board (Century/ Greenply/ Kitply) with new telescopic channel of Make : TATA/ Jindal/ Cent (ISI Marked) of approved quality and make them functional. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/E6/MAP/07 / FD/E6/MAP-15(R)

Removing of old unserviceable back/ sides of Table Bed side (MAP) and S&F of new back/ sides made of approved quality MDF board (Century/ Greenply/ Kitply) as per the drg. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/E6/MAP/07 / FD/E6/MAP-15(R)

Removing of old unserviceable tray of table bed side (MAP) and S&F of new tray made of approved quality MDF board (Century/ Greenply/ Kitply) as per the drg. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/E6/MAP/07 / FD/E6/MAP-15(R)

BIN SOILED LINEN MULTIPURPOSE (FD/E6/MAP/09) Removing of old unserviceable shutter and hinhes of bin soiled linen multipurpose and S&F of new shutter made of approved quality MDF board (Century/ Greenply/ Kitply) as per the drg with suitable stainless steel hinges (ISI Marked). The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/E6/MAP/09

Removing of old unserviceable handle of bin soiled linen multipurpose and S&F of new stainless steel chrome plated handle of size 125mm (alongwith all accessories for fixing) of superior quality as per the drg. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/E6/MAP/09

Removing of old unserviceable drawer including unserviceable channel of bin soiled linen multipurpose and S&F of new drawer made of approved quality MDF board (Century/ Greenply/ Kitply) as per the drg and new telescopic channel Make : TATA/ Jindal/ Cent (ISI Marked) alongwith all accesories for fixing of approved quality. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/E6/MAP/09

CHAIR WRITING CUSHIONED (MAP) (FD-E6/MAP/12) Removing of existing old unserviceable seat and S&F of new hot pressed plywood upholsted with fabric and moulded plyurethane foam with PVC liping all round seat of chair writing cushioned with approved tapestry cloth not less than Rs. 250/- per metre, complete all as per drawing and as specified and as directed by Engr-in-charge.

All as per serial item No. 19.00 here-in-above but back of chair writing.

Removing old unserviceable arm rests of chair writing and S&F of new arm rest with accessories for fixing in accordance with drg and as directed by Engr-in-Charge. Drawing No. FD-E6/MAP/12

Spot welding to existing cracked/ joints of chair writing cushioned (MAP) by gas welding not exceeding 2.5cm in length as required and after welding joints be plain/ smoothen steel structure properly by grinding, complete all as specified on drg and as directed. Drawing No. FD-E6/MAP/12

Scratching out old defective paint/ rusted spots from chair writing (MAP) by abbressive paper and making the surface smooth by rectfying the bends/ dents of cantilever pipe applying two coats of synthetic paint of first quality by sprayer method and S&F of new nylon shoes for proper balance, complete all as specified and directed by Engr-in-Charge. Drawing No. FD-E6/MAP/12

BED PLY TOP STEEL (MAP) (FD/E6/MAP-08(R)) Taking out unserviceable plywood from bed plywood steel and S&F of new 12mm thick BWR/BWP, AA, plywood (Make : Century/ Greenply/ Kitply), 7 ply phenol bonded and fix with suitable round head steel nuts and steel bolts of suitable size as fit to the bed from headrest to the footrest, complete all as specified and rest as per drg.

Removing old unserviceable existing headrest and S&F of new plank of headrest made up of prelaminated MDF Board 18/19mm thick (Century/ Greenply/ kitply/ Action Tesa) duly covered with PVC beading all around. The shade of the headrest should be matched with existing footrest, complete all as specified and rest as per drg. Drawing No. FD/E6/MAP-08(R)

Removing old unserviceable footrest and S&F of new plank of footrest made up of prelaminated MDF Board 18/19mm thick (Century/ Greenply/ Kitply) duly covered with PVC beading all around. The shade of the footrest should be matched with existing headrest, complete all as specified and rest as per drg. Drawing No. FD/E6/MAP-08(R)

Spot welding to existing cracked/ joints of bed hard steel (MAP) by arc welding not exceeding 2.5cm in length as required and after welding joints be smoothen properly by grinding and proving suitable nut and bolts to fix, complete all as specified and shown on drg. Drawing No. FD/E6/MAP-08(R)

Scratching out old defective paint/ rusted spots from bed hard steel (MAP) frame by abbressive paper and making the surface smooth by filling putty etc. and applying two coats of synthetic black enamel paint of first quality by sprayer method, complete all as specified and directed by Engr-in-Charge. Drawing No. FD/E6/MAP-08(R)

CHARPOY HARD TOP STEEL (MAP) (FD/MAP-II/01) Taking out unserviceable plywood from bed plywood steel and S&F of new 12mm thick BWR/BWP, AA, plywood (Century/ Greenply/ Wrown/ Kitply), 7 ply phenolbonded and fix as fit to the bed from headrest to the footrest. complete all as specified and rest shown on drg.

Scratching out old defective paint spots from bed hard steel (MAP) frame by abbressive paper and making the surface smooth and applying two coats of synthetic black enamel paint of first quality by sprayer method, complete all as specified and directed by Engr-in-Charge. Drawing No. FD/MAP-II/01

CHAIR COMPUTER / EXECUTIVE REVOLVING (FD/E6/MAP/01) Removing of existing old damaged pedestal assembly with wheels and S&F new heavy duty pedestal assembly with wheels (swvel type), size shall be as per existing pedestal assembly with castor wheels (superior quality), complete all as specified and directed and rest shown on drg.

Removing of old unserviceable hydraulic system for height adjustment and S&F new hydraulic system for height adjustment, size shall be as per existing hydraulic system for height adjustment, complete all as specified and directed by Engineer-in-Charge. Drawing No. FD/E6/MAP/01

Removing of old unserviceable seat and S&F new seat of chair computer of 12mm thick hot pressed plywood upholsted with fabric and moulded polyurethane foam with PVC liping all round with approved tapestry cloth, not less than Rs 250/- per metre, complete all as specified and directed by Engineer-in-Charge. Drawing No. FD/E6/MAP/01

All as per serial item No. 33.00 here-in-above but back of chair computer.

Removing of old unserviceable armrest and S&F new armrest weather and scratch proof of superior quality including accessories for fixing of the same, size shall be as per existing arm, complete all as specified and directed. Drawing No. FD/E6/MAP/01

ALMIRAH LARGE STEEL (FD/E6/MAP/18) Taking down old unserviceable existing lock from almirah large steel (MAP) from (Main door lock and locker unit inside) and provide new approved quality ISI Marked lock having six levers with duplicate keys and fixed in position, complete all as specified and directed by the Engineer-in-Charge.

LUBRICATING IN HINGES / LOCKING MECHANISM Provide and apply machine oil or silicon spray in hinges of almirah steel large to keep the hinges functioning smooth and lubricating the lock mechanism. Use graphite powder or a lock lubricant to keep the lock mechanism functioning smoothly, complete all as specified and directed. Drawing No. FD/E6/MAP/18

Removing of unserviceable shelves and conduit pipe with brackets and S&F of new shelves made up 1mm thick MS sheet with suitable hooks and 20mm dia conduit pipe SS chromium plated with end to end bracket fixed with suitable rivet, complete all as specified and directed by Engr-in-charge. Drawing No. FD/E6/MAP/18

DOOR ALIGNMENT ISSUES Adjusting Hinges : If the doors become misaligned, adjust the hinges to re-align them by loosening the screws, repositioning the door and then tightening the screws again, complete all as specified and directed. Drawing No. FD/E6/MAP/18

REPLACING DAMAGED HANDLES Taking down old unserviceable existing handle (main door handle) from almirah large steel (MAP) and provide new approved quality matching stainless steel handle and fixed in position, complete all as specified and directed by the Engineer-in-Charge. Drawing No. FD/E6/MAP/18

Taking down old unserviceable existing handle from almirah large steel (MAP) locker unit inside and provide new approved quality matching stainless steel handle and fixed in position, complete all as specified and directed by the Engineer-in-Charge. Drawing No. FD/E6/MAP/18

Removing of old unserviceable drawer of almirah large steel (MAP) and S&F of new drawer made of approved quality 1mm thick mild steel as per the drg. Removing of old unserviceable handle from drawer and S&F of new handle. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/E6/MAP/18

Scratching out old defective paint spots including denting from almirah large steel by abbressive paper/ cloth and making the surface smooth by filling putty etc. and applying two coats of synthetic paint of first quality by sprayer method, complete all as specified and directed by Engr-in-Charge. Drawing No. FD/E6/MAP/18

TABLE COMPUTER (FD/E6/MAP/03) Removing unserviceable top of table computer and S&F new top made of 18mm thick prelaminated MDF board with teak beading duly polished all around, complete all as specified and directed.

Removing of old unserviceable drawer of table computer including telescopic channel and S&F new drawer made of approved material as per the drg and new telescopic channel of Make TATA/ Jindal/ Cent (ISI Marked) of approved quality and provide a ss chrome plated handle of size 50mm and make them smooth functional. The fixing shall be done with standard workmanship, complete all as specified and directed by Engr-in-charge. Drawing No. FD/E6/MAP/03

Removing of old unserviceable keyboard tray including unserviceable telescopic channel of table computer and S&F of new keyboard tray made of approved material as per the drg and S&F of new telescopic channel both sides of Make TATA/ Jindal/ Cent (ISI Marked) of approved quality and make them smooth functional and teakwood beading (5mm thick and 22mm width and length as per size of keyboard tray on front side of tray duly two coats of french polish shall be provided. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-Charge. Drawing No. FD/E6/MAP/03

TEAPOY VERANDAH MAP (FD/E6/MAP/17) Removing unserviceable top of teapoy verandah steel and S&F new top made of 18mm thick prelaminated MDF board (Century/ Greenply/ Kitply) duly covered with teakwood beading 4mm thick duly polished, complete all as specified and directed.

Scratching out old defective paint spots from teapoy verandah steel surfaces by abbressive paper/ cloth and making the surface smooth and applying two coats of synthetic black paint of first quality by sprayer method, complete all as specified and directed by Engr-in-Charge. Drawing No. FD/E6/MAP/17

PEG TABLE MAP (FD/MAP/11) Removing of old unserviceable leg from peg table and S&F of new leg as per existing size/ shape/ pattern, made out of first class well seasoned teak wood including polishing to match the other parts and fix nylon buffers at bottom of all legs, complete all as specified and as directed by Engr-in Charge. Drawing No. FD/MAP/11

Removing of old unserviceable rear/ front rail from peg table and S&F of new front/ back rail made out of first class well seasoned teak wood including polishing as per existing size, shape and pattern, complete all as specified and directed and shown on drawing. Drawing No. FD/MAP/11

Replacing of old unserviceable top of peg table and S&F of new top made out of prelaminated MDF board (one side decorative), exterior grade BWR, complete all as specifed and as shown on drawing. Drawing No. FD/MAP/11

M&L for applying two coats of french polish on the peg table (MAP) after preparing by filling cracks with putty/ suitable material of surfaces and making smooth surfaces with suitable ambry paper, complete all as speified and as directed by Engineer-in-Charge. Drawing No. FD/MAP/11

TABLE DINING 4/6/8 PERSON MAP (FD/MAP-II/03) Removing of old broken unserviceable leg from table dining and S&F of new legs as per existing size, shape and pattern, made out of first class well seasoned teak wood including nylon buffer fix at bottom of all legs and polishing to match the other parts, complete all as specified and as directed by Engr-in-Charge.

Removing of old unserviceable rear/ front rail from table dining and S&F of new front/ rear rail made out of first class well seasoned teak wood of approved quality including polishing as per existing size, shape and pattern, complete all as specified and directed by Engr-in-Charge. Drawing No. FD/MAP-II/03

Removing of old unserviceable (broken) stiffners and S&F of new stiffner of size 90x25mm thick by dove tail joint of approved quality made out of first class well seasoned teak wood as per size, shape and pattern as mentioned in drg including polishing, complete all as specified and as directed by Engr-in-Charge. Drawing No. FD/MAP-II/03

Replacing of old unserviceable top of table dining 8 person (1800mm x 900mm) and providing new top 18mm thick prelaminated MDF board Grade-I (one side deraocative), exterior grade, complete all as specifed and as shown on drg. Drawing No. FD/MAP-II/03

Replacing of old unserviceable top of table dining 6 person (1500 mm x 900mm) and providing new top 18mm thick prelaminated MDF board Grade-I (one side deraocative) exterior grade, complete all as specifed and as shown on drg. Drawing No. FD/MAP-II/03

Replacing of old unserviceable top of table dining 4 person (1200mm x 900mm) and providing new top 18mm thick prelaminated MDF board Grade-I (one side deraocative) exterior grade, complete all as specifed and as shown on drg. Drawing No. FD/MAP-II/03

Removing of old existing/ damaged 150x30x5mm thick MS Right Angle screwed with rail and leg and fix new MS right angle of same size and shape for extra strength, complete all as specified and rest all as per drawing. Drawing No. FD/MAP-II/03

M&L for applying two coats of french polish to table dining after smoothening surface by emery paper, complete all as specified and directed. Drawing No. FD/MAP-II/03

TABLE CENTRE MAP (FD/MAP/08) Removing of old unserviceable leg from table centre and S&F of new leg as per existing size, shape and pattern, made out of first class well seasoned teak wood including polishing to match the other parts and fix nylon buffers at bottom of legs, complete all as specified and as directed by Engr-in Charge.

Removing of old unserviceable (broken) stiffners and S&F of new stiffner of approved quality made out of first class well seasoned teak wood as per existing size, shape and pattern as mentioned in drawing including polishing, complete all as specified and as directed by Engr-in-Charge. Drawing No. FD/MAP/08

Removing of old unserviceable rear/ front rail from table centre and S&F of new front/ back rail of approved quality including polishing as per existing size, shape and pattern, made out of first class well seasoned teak wood, complete all as specified and directed. Drawing No. FD/MAP/08

Removing of old unserviceable batten from table centre and S&F of new batten 45mm x 20mm thick made out of first quality teak wood batten of approved quality including polishing as per existing size, shape and pattern, complete all as specified and directed. Drawing No. FD/MAP/08

Replacing of old unserviceable top of table centre and providing new top made out of prelaminated MDF board (one side deraocative) exterior grade BWR, complete all as specifed and as shown on drawing. Drawing No. FD/MAP/08

M&L for applying two coats of french polish to table centre after smoothening surface by emery paper. Final touches once the first coat is applied, allowed it to dry completely before assessing the finish/another coat, complete all as specified and directed. Drawing No. FD/MAP/08. Note :- To providing a surface with a high gloss shine GCI Wood Polish Thinner is used to dissolve Lakdhana or Shellac.

TABLE DRESSING LADIES MAP (FD/MAP-II/07) Removing old unserviceable broken looking mirror from table dressing ladies and S&F new approved quality 5mm thick (+/- 5% tolerance) electro copper plated of polished sheet glass mirror of suitable size of make Modi / Atul / Saint Gobain, duly fixed to existing wooden frame and 6mm thick commercial ply wood (Kitply/ Greenply/ Century/ Archid) including applying two coats of french polish after preparation of surface, complete all as specified and shown on drawing and directed by Engr-in-charge.

Removing of old unserviceable shutter including hinges of table dressing ladies and S&F of new shutter made of approved quality MDF board (Century/ Greenply/ Archid/ Action Tesa) as per the drawing with suitable stainless steel hinges. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/MAP-II/07

Removing of old unserviceable handle of table dressing ladies and S&F of new stainless steel chrome plated of size 75mm handle of superior quality of approved material. The fixing shall be done with standard workmanship, complete all as specified and directed by Engr-in-charge. Drawing No. FD/MAP-II/07

Removing of old unserviceable drawer of table dressing ladies (MAP) and S&F of new drawer made of approved quality MDF board (Century/ Greenply/ Kitply) and removing of unserviceable telescopic channel from both sides and S&F of new telescopic channel of both sides of Make TATA/ Jindal/ Cent (ISI Marked) of approved quality. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-charge. Drawing No. FD/MAP-II/07

M&L for apply two coats of french polich on the dressing table ladies after preparing the old surface and making smooth surfaces by rubbing with suitbale emery paper, complete all as specified and as directed by Engr-in-Charge. Drawing No. FD/MAP-II/07

TABLE DRESSING GENTS MAP (FD/E6/MAP/16) Removing old unserviceable broken looking mirror from table dressing gents and S&F of new approved quality 5 to 6mm thick (+/- 5% tolerence) electro copper plated sheet glass mirror of suitable size 1120mm x 520mm of make Modi / Atul / Saint Gobain, to be fixed in existing wooden frame and 6mm thick commercial ply wood (Kitply/ Century/ Greenply/ Archid) including applying two coats of french polish after preparation of surface, complete all as specified and as shown on drwing.

Removing of old unserviceable glass shelf including runner and S&F of new plain glass shelf 5mm thick of make Modi/ Atul/ Saint Gobain and runner made out of teak wood/ glass holder, complete all as specified and rest all as shown on drawing. Drawing No. FD/E6/MAP/16

Removing of old unserviceable existing magnetic catcher and S&F of new magnetic catchers with suitable SS screws, complete all as specified and directed. Drawing No. FD/E6/MAP/16

CHAIR DINING JCO's / OR's (MAP) (FD/MAP-II/05) Removing of unserviceable front leg from chair dining JCO'S / OR's and S&F of new approved quality seasoned 1st class teak wood leg to match other leg as existing pattern and design and fix nylon buffers at bottom of all legs, complete all as specified and directed.

All as per serial item No. 75.00 here-in-above but rear leg.

All as per serial item No. 75.00 here-in-above but back batton.

All as per serial item No. 75.00 here-in-above but front/ rear/ side rail.

Taking down unserviceable plastic seat of chair dining JCO's / OR's (MAP) and S&F of new approved quality 50mm thick 40 density foam covered with velvet/ tapestry cloth not less than Rs. 250/-per meter including 12mm thick plywood as size and shape of seat of existing chair with support of 4 x corner fixed with wood glue and countersunk chinese black screw, complete all specified and directred by Engr-in-Charge. Drawing No. FD/MAP-II/05. Make of cushion : Sleepwell/ Kurlon/ Featherfoam (top Model)

M&L for applying two coats of french polish on the chair dining JCO's / OR's after preparing by filling cracks with putty / suitable material of old surfaces and making smooth surfaces with suitable ambry paper, complete all as speified and as directed by Engineer-in-Charge. Drawing No. FD/MAP-II/05

TV TROLLEY (FD/E6/MAP/04(R)) Removing unserviceable top of TV Trolley and S&F of new top made of 18/19mm thick prelaminated particle board duly covered with teakwood beading 4mm thick duly polished, complete all as specified and directed. \Make of MDF Board : Century/ Greenply/ Kitply.

Removing unserviceable left side / right side and back side particle board and S&F new ones made of 18mm thick prelaminated particle board, complete all as specified and directed. Make of MDF Board : Century/ Greenply/ Kitply. Drawing No. FD/E6/MAP/04(R)

Removing unserviceable bottom of TV trolley and S&F new bottom made of 18/19mm thick prelaminated particle board along with 04 castors 50mm dia swivel wheels heavy duty fix with steel screw at corners, complete all as specified and directed. Make of MDF Board : Century/ Greenply/ Kitply. Drawing No. FD/E6/MAP/04(R)

Removing of existing broken glass shutter and S&F of 5.5mm thick openable glass shutter with magnetic catcher alongwith accessories for fixing, complete all as specified and rest shwn on drawing. Make of Glass : Modi Guard/ Saint Gobain/ Atul. Drawing No. FD/E6/MAP/04(R)

Removing of old unserviceable drawer of TV trolley and S&F of new drawer made of approved quality 18/19mm thick MDF board (Century/ Greenply/ Kitply) as per the drawing and removing of unserviceable telescopic channel from both sides and S&F of new telescopic channel on both sides of Make TATA/ Jindal/ Cent (ISI Marked) of approved quality and a SS chrome plated handle of size 100mm and make them functional. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-Charge. Drawing No. FD/E6/MAP/04(R)

Removing of old unserviceable shutter of TV trolley and S&F of new shutter made of approved quality MDF board (Century/ Greenply/ Kitply) as per the drawing with suitable stainless steel hinges piano type alongwith 100mm brass handle. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-Charge. Drawing No. FD/E6/MAP/04(R)

Removing of old unserviceable tray of TV trolley and S&F of new tray made of approved material as per the drawing and removing of unserviceable telescopic channel from both side and S&F of new telescopic channel on both sides of Make TATA/ Jindal/ Cent (ISI Marked) of approved quality and make them smooth functional. The fixing shall be done with standard workmanship, complete all as specified and as directed by Engr-in-Charge. Drawing No. FD/E6/MAP/04(R)

RACK SHOE STEEL (FD/E6/MAP/13) Scratching out old defective paint spots / rust spot by abbressive paper/ cloth and making the surface smooth of shoes rack steel then applying two coats of synthetic black paint of first quality by sprayer method, complete all as specified and directed by Engr-in-Charge.

S&F rubber shoe for rack shoe steel, superior quality, size mentioned in drawing, complete all as specified and directed. Drawing No. FD/E6/MAP/02(R)

SCHOOL CHAIR WITH HAND BOARD (FD/E6/MAP/05) Detach old damaged / unserviceable particle boad and S&F of 18mm thick prelaminated particle board top openable with PVC edging, screwed to 25mm hollow steel pipe inserted in 20mm rod welded to frame, complete all as specified and directed.

Removing old broken existing one piece seat and back and S&F of one piece PVC back and seat blow plast or equivalent, complete all as specified and shown on drawing and directed by Engr- in-Charge. Drawing No. FD/E6/MAP/05

Removing of existing broken lock clips with bag basket and providing new 4 x lock clips along with 1 bag basket, fixing them with new nut, bolts, complete all as specified and rest shown on drawing and directed by Engr-in-charge. Drawing No. FD/E6/MAP/05

S&F rubber shoe for chair school, superior quality, size mentioned in drawing, complete all as specified and directed. Drawing No. FD/E6/MAP/05

CHAIR VERANDAH MAP (FD/MAP-II/06) Removing old broken existing seat and S&F of new seat, complete all as specified and shown in drawing and directed by Engr-in-Charge.

Removing old broken existing back and S&F of new back, complete all as specified and shown in drawing and directed by Engr-in-Charge. Drawing No. FD/MAP-II/06

M&L for painting to old defective paint spots / denting and remove bend from structure with appropriate tools from chair verandah with abrasive cloth and making the surfaces smooth by filling putty etc. and applying two coats of synthetic white paint, complete all as specified and shown in drawing and directed by Engr-in-Charge. Drawing No. FD/MAP-II/06

S&F rubber shoe for chair verandah superior quality, size mentioned in drawing, complete all as specified and directed by Engr-in-Charge. Drawing No. FD/MAP-II/06

STOOL ONLY (From the drawing of table dressing ladies including stool FD/MAP-II/07) Removing of old unserviceable 75mm foam 40 density cushion covered with leatherite/ tapestry cloth and S&F of new 75mm foam 40 density cushion covered with leatherite, complete all as specified and rest all as shown drawing and directed by Engr-in-charge. Make of cushion : Kurlon Model Goldline or equivalent in Sleepwell / Featherfoam.

Removing of old unserviceable plywood with folding handle and S&F of new 12mm thick plywood with superior quality foldable handle, complete all as specified and rest all as shown drawing and directed by Engr-in-charge. Drawing No. FD/MAP-II/07 (Stool only)

Removing of old unserviceable prelaminated MDF board from front and sides of stool and S&F of new MDF prelaminated board. The fixing shall be with standard workmanship, complete all as specified and rest all as shown drawing and directed by Engr-in-charge. Drawing No. FD/MAP-II/07 (Stool only)

Removing of old unserviceable 6mm thick plywood from bottom of stool dressing (MAP) and S&F of new plywood. The fixing shall be with standard workmanship, complete all as specified and rest all as shown drawing and directed by Engr-in-charge. Drawing No. FD/MAP-II/07 (Stool only)

Removing of old unserviceable nylon wheels from bottom of stool and S&F of new heavy duty revolving nylon double wheels (4 Nos) including accessories for fixing, complete all as specified and directed by Engr-in-charge. Drawing No. FD/MAP-II/07 (Stool only)

Removing of existing unserviceable torn out Nylon Newar from Charpoy (FD-220) GI pipe and S&F of new 12mm thick plywood (7 ply Plywood, BWR/BWP Grade, ISI marked of size 1.95 mtr x 0.90 mtr including 03 (Three) Nos of stiffner of size 900mm x 40mm x 5mm of MS flat iron duly painted with two coats of black paint and fixed with long rail (by nut and bolt) so as to fit tightly with inner wall of both the long rail at an equal intervals to provide more strength to hard top. Necessary holes and perforation to be made in short rail, long rail & stiffener as per direction of Engineer-in-Charge. Screw/ check nut to be used of suitable size. Corner of plywood is to be rounded off properly. All other work to be done as specified in drawing and direction of Engineer-In-Charge. Drawing No. FD-220. Make :- Century/ Greenply/ Archidply/ Kitply

Taking down unserviceable broken long rails of charpoy (FD-220) GI pipe and S&F of new long rails of charpoy, made out of GI pipe of 32mm bore medium grade ISI marked and approved by Engr-in-charge including threading at both ends, complete all as specified and shown on drawing and as directed by Engineer-in-Charge. Make of GI Pipe : Prakash Surya /TATA / JINDAL

Taking down unserviceable broken short rail of charpoy (FD-220) GI pipe and S&F of short rail (Short rail shall be made from long rail obtained from serial item No. 104.00 here-in-above) including threading both sides. The converted short rails shall be presented to Engr-in-Charge for inspection and approval. If during inspection, any of the converted short rails are found to be not as per the drawing, specifications or required size or if threading is found defective, the contractor shall replace the same with new one including threading at no extra cost, complete all as specified and shown on drawing and as directed by Engineer-in-Charge. Make of GI Pipe : Prakash Surya /TATA / JINDAL

Taking out unserviceable elbow 3 Way of 32mm bore of GI for Charpoy (FD-220) GI pipe and S&F of new elbow 3 way of 32mm bore ISI marked as approved by Engr-in-Charge, complete all as specified and shown on drawing and as directed by Engineer-in-Charge. Make : TATA/ UNIK/ JINDAL

Taking down unserviceable broken check nuts of Charpoy (FD-220) GI pipe and S&F of new check nuts, suitable for Charpoy GI Pipe as approved by Engr-in-Charge, complete all as specified and shown on drawing and as directed by Engineer-in-Charge.

Taking down unserviceable legs to Charpoy (FD-220) GI Pipe and fixing legs in Charpoy (Legs shall be made from short rail obtained from serial item No. 105.00 here-in-above) including threading on one side and provide one hard wood block of size 35mm x 35mm x 40mm on bottom side of each leg. The converted GI legs shall be presented to Engineer-in Charge for inspection and approval. If during inspection, any of the converted GI legs are found to be not as per the drawing specifications or required size or if threading is found defective, the contractor shall replace the same with new including threading at no extra cost, complete all as specified and shown on drawing and as directed by Engineer-in-Charge

Taking down unserviceable existing legs from Charpoy (FD-220) GI pipe and S&F of new GI legs duly threading one side and provide one hard wood block of size 35mm x 35mm x 40mm on bottom side of each leg, complete all as specified and shown on drawing and as directed by Engineer-in-Charge.

shivom builders (BID ID -3478607)

M/S SHARMA TRADERS (BID ID -3476708)

VEE KAY IND (BID ID -3468732)

TULSI RAINA AND SONS (BID ID -3478477)

PACHNANDA BUILDERS (BID ID -3479011)

R K BUILDERS (BID ID -3467252)