Repair to leakage/seepage, joinery, flooring, ceiling, sanitary fitting, plastering, painting, approach path, drain and internal electrification of OTM Accn of 21 Bihar, 4 Marathali, 20 Kumaon and 244 Fd Wksp Coy EME at Birpur under AGE B/R-II of GE

Amount

Demolition of cement concrete ground floor and paving nexc 15cm thick (below or above ground level) and dispose off rubbish outside the MD land as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and dispose off rubbish outside the MD land as directed by Engr-in-Charge.

M&L for 75mm th PCC 1:3:6 type C-2 as in plinth protection, finished even and fair without using extra cement.The plinth protection shall be laid in alternate bays n exe 2 sqm with 10mm wide joints filled with bitumen mastic comprising of 1 part of hot bitumen 85/25 grade and 3 parts sand all by weight complete all as specified.

M&L for coloured Non Skid Ceramic joint free tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM (1:6) complete all as specified and directed .

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 all as directed .

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300x200 mm or 300X450 mm, 7mm thick over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) as in skirting cut from tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slury and pointed in white or coloured cement to match including screed bed 10mm thick in cm 1:4 all as directed by Engr-in-Charge.

Demolition of Stone slabs and tiles laid, bedded in any mortar of any description or thickness in floors, aprons etc.all as directed by Engr-in-Charge.

M&L Udaipur green stone pre polished mirror for flooring/shelf slabs 12-15mm thick over 15 mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rounding off exposed edges of slaball as directed by Engr-in-Charge.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, chajjas, fascias, fins and similar works and dispose off rubbish with in MD land all as directed by Engr-in-Charge.

M&L for reinforced cement concrete (nominal mix) 1:2 :4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams , column in floors, shelves and the like all as directed by Engr-in-Charge.. Note :- Reinforcement & formwork shall be measured and paid for separately.

S&F TMT MS bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified .

M&L for formwork to soffits and sides of suspended slabs such as roof slabs, floor slabs, sides, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete all as directed by Engr-in-Charge..

Taking down of chowkhat with shutter (without taking of shutter from the framed area n.exc 1.50 sqm each complete all as specified and directed by Engr-in-charge

Taking down of chowkhat with shutter (without taking of shutter from the frame area exc 1.50 sqm & n.exe 4sqm each complete all as specified and directed by Engr-in-charge

Taking out shutters of any description exe 1 sqm and nexe 2Sqm each complete all as specified and directed by Engr-in-charge

Taking out shutters of any description nexe 1 sqm complete all as specified and directed by Engr-in-charge

M/L 30mm thick 2nd class hard wood factory made Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) all as directed by Engr-in-Charge.

M/L 30mm thick 2nd class hard wood factory made Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) all as directed by Engr-in-Charge.

S&F 35 mm thick Factory made BWR flush shutter ,solid core construction, with block board core and plywood face pannel, commercial type on both sides all as specified and directed by Engr-in-charge

M/L 35mm thick 2nd class hard wood factory made Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) all as directed by Engr-in-Charge.

M&L for second class hard wood, plain, solid, straight chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr-in-charge

S&F Factory made pre laminated solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part II.

S&F pre laminated Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam single piece extruded pvc profile and edgs will be painted to match with prelam sheet,PVC sheet are to be reinforced with 19x19mm MS square tube EPDM rubber gasket weather seal shall be provided through out the frame. The profile shall be mitre cut at two corners and joint by insrting 2 nos of 150mm long backets of 15mmx15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed and fixing in opening as per specification & drawing.

S&F 18/19mm prelaminated particle board, exterior grade, prelaminated both sides with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work and 4mm thick wooden leaping alround the shutter.including dismantling of old boarding complete all as specified and duirected by Engr-In-Charge

S&F factory made PVC flush type shutter of 18mm thickness consisting of panel of PVC profile of 18mm (+ 0.7mm) thick cillica ply of denisity 600 kg per cum manufactured by ISO-9000 certified company using for shutter cillicia ply 18mm thick and fixed with frame. The thickness of shutter is edges painted by matching colour of PVC lining of plain/prelim coloured PVC sheet using etc complete as per manufacture specification.including dismantling of old shutter complete all as specified and duirected by Engr-In-Charge

Welding or repair of steel window by welding to broken hinge or peg stay, sash bar and guard bars etc with complete each window work. at different location, as directed by Eng-in-charge. (Any items such as hinge, peg stay, sash bar, guard bar etc if provided new, shall be paid as supply only under following items)

Supply only following items for carrying out repairs to steel windows under item 27 above:-

Mild Steel Handle

Mild steel Peg stay

S&F in repairs factory made steel windows with side hung shutters including box type hinges, MS handles , peg stay and tower bolts complete with glazing bars dovetailed or welded with one shop coat of primer complete all as specified and directed.

S&F in repairs factory made steel windows with side hung shutters including box type hinges, MS handles, peg stay and tower bolts complete without glazing bars with one shop coat of primer complete all as specified and directed.

S&F in repairs factory made steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

Taking down existing projected type hings from the steel window carefully without disturbing frame and S&F 50 mm long mild steel box type hinge welded to steel frame and shutter with welding and making good including two coats of synthetic enamel paint over a coat of primer to match the existing surfaces . The work shall be executed at site up to the three storeyed bulding, the rate of scaffolding shall be deemed to be included the quoted rate of this item complete all as specified aand directed by Engr-in-charge

M&L plain fillets 2nd class Hard wood exc 13 & n exc 25 sqcm, square or rectangular in section, wrought, secured with nails or barbs complete all as specified and directed.

S & F Framed work such as grills, gratings, with ends of bars welded, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming toFe 290. Gde-E-165 complete all as specified and directed.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel, and fixed as directed by Engr-in-charge

S&F 75mm long butt hinges, medium weight, cold rolled mild steel, and fixed as directed by Engr-in-charge

S&F 100 mm size stainless steel 304 grade butt hinges and fixed with stainless steel screws, complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long, solid in one piece stainless steel 202 grade bright finish barrel tower bolts of 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150 mm long, solid in one piece stainless steel 202 grade bright finish barrel tower bolts of 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150mm size solid in one piece stainless steel handles 202 grade bright finish D type and fixed with stainless steel screws complete all as specified and directed by Engr-in-Charge.

S&F 125mm size solid in one piece stainless steel handles 202 grade bright finish D type and fixed with stainless steel screws complete all as specified and directed by Engr-in-Charge.

S&F in repairs 300mm long MS Helical door spring fixed to steel chowkhat including necessary welding or fixed to wooden door frame including roller and roller plate etc complete all as specified and directed by Engr-in-Charge. Make : Raja/ Ritz/ Classic/ Sandhu

S&F hasp and staple 100mm safety type, stainless steel 202 grade bright finish with hinge pin including bolt to hinge plate and fixed with screws all as specified and directed by Engr-in-Charge.

S&F floor door stopper of stainless steel 50mm size double legged and tongue, 202 grade bright finish , with hard drawn steel spring, fixed in floor all as specified and directed by Engr-in-Charge..

S & F continuous (Piano) hinges, stainless steel 202 grade bright finish, width of flaps (when open) 30 mm all as specified and directed by Engr-in-Charge.

S&F magnet catcher for cub board with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F 250 mm long stainless steel 202 grade bright finish sliding door bolt (bolt type, dia of bolt 16mm) with hasp, staple , fixing clips, fixing bolts and sliding bolt of stainless steel and fixed all as specified and directed by Engr-in-charge

S&F in repair peg set of five stainless steel fixed on CP steel plate 40mm wide including fixing screw as per approved sample.

M & L sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. 0.5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed by Engr-in-Charge.

M & L sheet glass ordinary quality 4 mm thick figured glass, pin head type and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. 0.5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing fixing new ones.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frame glazed with putty or fixed with beads all as specified and directed.

S&F Stainless steel 304 grade wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples with 8% nickle all as directed by Engineer- in -Charge.

S&F in repairs Stainless steel 304 grade wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples with 8% nickle all as directed by Engineer- in -Charge.

M&L for 2ndclass hardwood beads, straight (n.exe 6.00 sq cm size) for fixing galvanised MS wire cloth renewed, including mitres etc complete all as directed by Engineer-in-charge.

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L for preparation of new untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified

M&L 10 mm thick ceiling plaster in CM (1:4) on fair faces of concrete surfaces finished even and smooth without using extra cement all as specified in SSR.

M&L rendering in patches (nexc 3.0 Sqm) 15m thick on fair faces of brick work in CM 1:4 and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge(Note : WPC measured and paid saperately)

M&L rendering 15mm thick in cement mortar (1:4) on fair faces of brick/ concrete surfaces of chajja/ facia, finished surfaces even and fair without using extra cement. (Water proofing compound where ever required, will be measured and paid separately)

M&L for rendering 15mm thick in cement mortar 1:6 on walls (fair / unfair finished faces of brick/concrete), finished even and smooth without using extra cement complete all as specified. (Water proofing compound where ever required, will be measured and paid separately)

Supply only water proofing compound Dr. Fixit / Fosroc

M&L for preparation of undecorated plastered / POP / Putty surfaces of walls and applying three coats of white wash complete all as specified and directed by Engr-in-charge

M&L for preparation of undecorated plastered / POP / Putty surfaces of ceilings and applying three coats of white wash complete all as specified and directed by Engr-in-charge

M&L for preparation of undecorated plastered / POP / Putty surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by Engr-in-charge

M&L for preparation of undecorated plastered / POP / Putty surfaces of walls and applying two coat of cement base paint over a coat of primer complete all as specified and directed by Engr-in-charge

Dismantling of wrought iron or mild steel work of any description not otherwise provided for.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness incl cover fillets.

Providing & fixing tiled false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of

All as per item No 70.00 Contd....the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 3mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, all complete at all heights as per direction of Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridge/valley complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any ecifriendly colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Rolled section as in main & cross beams, hip & jack rafters; purlins where connecting to common rafters & running rails & guides for sliding doors; fixed with angles cleats o other connecting plates conforming to FE- 410W (Gde-E -250) quality -A

Taking up or down steel tubing and connections with all fittings for 15 mm bore GI tubing.

Taking up or down steel tubing and connections with all fittings for 20 mm bore GI tubing.

Refixing of old steel tubing 15mm bore, in new or old position with all new fittings to floor, wall or ceiling including cleaning old tubing as directed by Engr-in-charge (Note: Old steel tubing retrived from taking down shall be reused)

Refixing of old steel tubing 20mm bore, in new or old position with all new fittings to floor, wall or ceiling including cleaning old tubing as directed by Engr-in-charge (Note: Old steel tubing retrived from taking down shall be reused)

M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing etc and making good cutting not exc 10cm girth.

S&F 15mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

S&F in repair 08 Litr Dual capacity PVC low level flushing cistern including PVC syphon and float valve with PVC long flushing pipe/ Bend complete fixing the cistern with wall connecting with WC complete all as specified and directed by Engr-in-charge.

S&F in repair 15mm nominal internal bore PVC connection 450mm long with two PTMT nuts and PVC washer for cistern / WHB / Sink complete all as specifed and directed by Engr-in-charge. Make : Prayag/ polytuf.

Disconnecting existing PVC tanks exc 500 but not exc 1000 ltr capacity and removing from site complete all as specified and directed by Engr-in-charge

S&F two layer external white 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) with threaded cover hoisted and fixed in position all as specified in SSR Part I including 20 mm PTMT float valve with PVC ball complete all as specified and directed by Engr-in-charge

S&F two layer external white 1000 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) with threaded cover hoisted and fixed in position all as specified in SSR Part I including 20 mm PTMT float valve with PVC ball complete all as specified and directed by Engr-in-charge

S&F in repair vitreous china wash hand basin, white flat back, size 550x400 mm excluding taps but including waste pipe, CP waste fittings 32mm size long shank and MS brackets all as specified and directed by Engr-in-charge Make: Cera, hindware, parryware

S&F in repair CP wall mixer (3 in 1) complete all as specified and directed. Make: Jaquar Model No CON281KN, HSH 1929 & OHS 1989/SHA 477 ES549 ES546 ES547A & ES 531 (Telephone shower)/ Pearl MAR090 (Wall mixer)HS470 (Hand Shower with tube) SHO 525 (Shower) SH516 (Arm).

S&F in repair CP central hole basin mixer fancy type 15mm dia all as specified and directed. Make- Jaquar (ESSCO) Model No DLX516, Mark : ESSCO ES-516/Pearl Mar 087.

S&F CP brass fancy type pillar tap Make - ESSCO MQT-508 KN or Equivalent in Jaquar and Pearl and as approved by GE complete all as specified and directed.

S&F in repair viterous china squatting pan (orissa pattern) long pan size 580x440mm white with integral footrest with cast iron spun 600 mm long 'P' trap, set in cement concrete type B-1 (1:2:4) complete (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in-charge.

S&F in repair vitreous china wash down water closet pan (Padestal pattern) white incl plastic water closet seat covers white closed pattern with flat bottom with mild steel chromium plated hinging device complete all as specified and directed.

S&F in repairs fancy type 5.50mm thick looking mirror with PVC moulding 40 mm wide all around with back 5mm thick PVC board of size 450x600x5mm thick as approved by Engr-in Charge.

S&F in repairs CP brass bib tap fancy type 15mm bore screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge Make :- Jaquar ESSCO DLX 526/MARC ES 526/Perl MAR 078

S&F in repairs CP brass stop valve/ Angle valve fancy type 15mm bore screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge. Make :- Jaquar ESSCO DLX 511/MARC ES 508/Perl MAR 075

S&F in repair 125 mm size chromium plated shower rose with swivel joints and CP arms for fixing with 15 mm dia GI pipe complete all as specified and directed. Make : Pearl SHP 524 & SHA 512/ Cera cat No CG 416/CH 103/ Prayag Gracia 980/ Jaquar ESSCO E05542A X ALE536A.

S&F in repair stainless steel sink made out of 1mm thick sheet kitchen or laboratory with plugs, washers including beding lime cement mortar to dwarf wall or including fixing cantilever brackets fixed to wall and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm (with drainage board) complete all as specified and directed.

S&F heavy duty threaded PVC water tank cover with fixing frame fixed on PVC tank with 4 Nos of screws complete all as specified and directed by the Engr-in-Charge.

Taking down from walls, floors or trenches AC / Salt glazed ware pipes and fittings upto 110mm bore complete all as specified and directed.

S&F 100mm dia centrifugally cast iron spun pipe (IS-3989-1984) in any length with or with ears, with cement joints laid in floors/ trenches as directed by Engr-in-charge

S&F 100mm dia centrifugally cast iron spun pipe (IS-3989-1984) in any length with or with ears, with cement joints fixed to walls as directed by Engr-in-charge

S&F 75 mm dia centrifugally cast spun iron pipe soil and waste pipe in any length with or with ears, with cement joints laid in floors as per IS-3989-1984.

S&F 75 mm dia centrifugally cast spun iron pipe soil and waste pipe in any length with or with ears, with cement joints fixed to walls as per IS-3989-1984.

S&F centrifugally cast iron (spun) bends any radius for 100 mm dia CI pipe with duck 's foot or heel rest fixed with cement joints complete all as specified and directed.

S&F centrifugally cast iron (spun) bends any radius for 75 mm dia CI pipe with duck 's foot or heel rest fixed with cement joints complete all as specified and directed.

S&F centrifugally cast (spun) iron branch peices SI-3989-1984, single(equal or unequal) ordinary or inverted (spigot or socket type), or with parrallel branches fitted with oval access doors of 100mm bore dia complete , ISI Marked, fixed in repairs all as specified & directed.

S&F centrifugally cast (spun) iron branch peicesSI-3989-1984, single(equal or unequal) ordinary or inverted (spigot or socket type), or with parrallel branches fitted with oval access doors of 100mm bore dia complete , ISI Marked, fixed in repairs all as specified & directed.

S&F centrifugally cast iron spun (SI-3989-1984) bend (any radius) of 100mm bore with oval access door as directed by Engr-in-charge

S&F centrifugally cast iron spun (SI-3989-1984) bend (any radius) of 75mm bore with oval access door as directed by Engr-in-charge

S&F 75 mm dia centrifugally cast (spun) SI-3989-1984 iron cowls as directed by Engr-in-charge

S&F 75 mm dia centrifugally cast (spun) iron floor trap, with CP grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in repairs for 75mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof

S&F in repairs for 100mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof

Cutting around the pipe 75/100mm bore waste / soil pipe including taking out plant roots up to any depth in brick masonary and rejointing in pipe joint in epoxy mortar (Asian/Berger/Sikka) and making good to existing surface all as directed by Engr-in-charge. (After the jointing pipe one week to be open for checking of leaking including scaffolding, removing mosses from chajja and roof projection)

Removing of bushes upto root level from the wall upto tirpple story building ( Block of four qtrs) and repairing of disturbed surface with epoxy mortar (Asian/Berger/Sikka) and making good with existing surface including removing mosses from chajja and roof projectioncomplete all as specified and directed by Engineer-in-Charge.

M&L applying evenly a tack coat industrial bitumen 85/25 at the rate of 1.20 Kg per Sqm including cleaning of surface on roof all as directed by Engr-in-charge.

M&L one coat of aluminium bitumen paint @ 0.30 litres/kg on the roof all as directed by Engr-in-Charge.

M&L for rendering 10mm thick on fair faces of roof surface and sunken portion in cm 1:3 finished even and smooth with using extra cement with water proofing admixture complete all as directed by Engr-in-charge.

M&L for PCC 1:5:10 type E2 using 40mm graded stone aggregate as in mass concrete for sunken floor filling all as directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls (Plastered) by brooming down with steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and finally clean with sand paper all as directed by Engr-in-Charge.

Complete removal of existing treatment of wall upto the plastered surface of wall by brooming down with steel wire brush and hand held electrical grinder, scraping down smoke soot, moulds, moss and efflorecent salts and trading oil and greasy spots and finally cleaned with sand paper all as directed by Engr-in-charge

M&L for preparation of old decorative surface of ceiling (plastered) by brooming down with coir brush and hand held electrical grinder, scraping down smoke soot, moulds, moss and efflorecent salts and trading oil and grasy spots and finally cleaned with sand paper all as directed by Engr-in-charge

M&L for applying one coat of white wash on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge.

M&L for applying one coat of white wash on old decorated already prepared surfaces of ceiling complete all as specified and directed by Engr-in-charge.

M&L one coat of oil bound distemper in any tint on already prepared old surfaces of walls complete all as specified and as directed by Engr-in-Charge.

M&L two coat oil bound distemper over a coat of suitable primer of any tint on old surfaces of walls complete all as specified and as directed by Engr-in-Charge.

M&L one coat of cement base paint on external wall surfaces already prepared old wall surfaces complete all as specified and as directed directed by Egnr-in-Charge.

M&L two coat of cement base paint on external walls surfaces already prepared old wall surfaces complete all as specified and as directed by Engr-in-Charge.

M&L for applying 2-3 mm thick wall care putty interior grade liquid on wall complete all as specified and directed by Engr-in-charge

M&L for preparation of wall and applying exterior grade wall care putty 2 to 3mm thick to make the surface smooth as specified and directed by Engr-in-Charge. Make : Berger/Asian/JK

M&L one coat of whether proof exterior emulsion paint on already prepared surfaces of brick/ concrete wall surfaces plastered surface of walls complete all as specified and directed by Engr-in-charge.

M&L applying two coats of whether proof exterior emulsion paint with primer on brick/ concrete wall surfaces plastered surfaces of walls complete all as specified and directed by Engr-in-charge.

Preparation of old AC sheets surfaces by brooming down with steel wires brushing and washing with water and applying one coat of external emulsion paint, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old painted steel surfaces over 10 cm width/girth and applying one coat of synthetic enamel paint all as specified and directed by Engr-in-charge.

M&L for preparation of old painted surfaces of wood over 10 cm width/girth and applying one coat of synthetic enamel paint all as specified and directed by Engr-in-charge.

Writing building Nos. with letters or figures (Block. Roman, Italic or Indian) n. exc 30 cm high all as specified and directed by Engr-in-Charge.

Cleaning of existing water storage tank with vaccume cleaner machine exc 250 to 500 ltrs capacity clean with R2 chemical (Taski) and descaling with desale chemical and finally cleaning with R1 chemical and dry and refilling including cleaning float as per PS CLause. Date of cleaning to and CA No to be painted with synthetic enamel paint on water storage tank with stencil in black/ white paint all as directed by Engr-in Charge. Note : (a) Any damage to float valve/ tank cover/ GI Pipe will be make good by contractor without any charge.

Cleaning of existing water storage tank with vaccume cleaner machine exc 1000 to 1500 ltrs capacity clean with R2 chemical (Taski) and descaling with desale chemical and finally cleaning with R1 chemical and dry and refilling including cleaning float as per PS CLause. Date of cleaning to and CA No to be painted with synthetic enamel paint on water storage tank with stencil in black/ white paint all as directed by Engr-in Charge. Note : (a) Any damage to float valve/ tank cover/ GI Pipe will be responsible and change/ repair will be the contractors responsibility without any charge.

Surface excavation not exc 30 cm deep and averaging 15cm deep and getting out including removing of excavated material/soil upto 100m complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep in soft/loose of soil for foundation, etc. or for shafts, wells, cesspits, manholes, pierholes, etc. and getting out complete all as specified and directed.

Returning filling in, any type of soil including spreading levelling watering and well ramming in layers n.exc 25 cm thick complete all as specified and directed.

Removing excavated material (Soils) to a distance n.exc. 50 m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D-1 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L for brick work with subclass 'B' bricks, straight, old size, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for reinforcement cut as required to facilitate demolition, complete all as specified and directed

M&L for 60 mm thick vibromatic reinforced precast cement concrete 1:1:2 (using 20mm graded stone aggregate) with 1.25 mm thick mild steel CR sheet around painted with 2 coats of bituminous paint , as in man hole cover slabs finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work, 100 mm long handle of 12mm dia round bar counter sunk by 25mm welded to reinforcement complete all as specified and directed by Engr-in-charge (Note : CA No and date will be engraved on covers. Reinforcement shall be measured and paid saperately. Curing will carried out with ponding method)

S&F TMT MS bar 8 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified .

M&L for PCC (1:3:6) (using 20 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

M & L for reinforced cement concrete drain pipes 150 mm dia NP-2, laid in trenches in foul condition, jointed with collars in cement mortar and tested, complete all as specified and as directed

M&L for cutting into existing manholes for connecting new drain, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 (using 20mm graded complete) smooth finished and reforming benching as required complete (Internal dia of pipe 150mm).

M&L for Cleaning of existing sewage pipe lines 100/150/200mm internal dia at any depth through manholes by removing the manhole covers, by means of hydraulic jet pressure machine or manually as required at site, getting out sludge and liquid materials from connecting manholes and sewar line, flushing with water after cleaning, reinstating the manhole cover to the original postion and removing the solids and sludge out of MD land complete all as specified and directed. (Note: Cost of removal of sludge/liquid material from sewage lines and manholes in same line is included in rate of this item. A particular sewage line which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment shall be made for repitetive cleaning if required )

M&L for dewatering and desludging of septic tank / soakage well of any size and depth by mechanical pumping by plugging inlet as requried, including effluent, solids and sludge out of MD land includind removing the manhole covers and reinstating to its original postion complete all as specified and directed by Engr-In Charge. (Note: A particular septic tank / soakage well which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment shall be made for repitetive cleaning if required)

M&L for Cleaning of blockage of Floor traps / Gully traps of bathroom / kitchen by getting out all the mud / sludge, cleaning of sewage pipe upto gully trap / first manhole and deposting the sludge in burrow pits of suitable size to a distance not exceeding 50 meters as directed and covering the same with the soil obtained from excavation of pit including all excavations and earth work complete all as specified and directed by Enge-In -Charge. (Note: A particular trap which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment shall be made for repitetive cleaning if required)

M&L for Cleaning of blockage of WC indian or European type by getting out all the mud / sludge, cleaning of sewage pipe upto first manhole and deposting the sludge in burrow pits of suitable size to a distance not exceeding 50 meters as directed and covering the same with the soil obtained from excavation of pit including all excavations and earth work complete all as specified and directed by Enge-In -Charge. (Note: A particular WC which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment shall be made for repitetive cleaning if required)

Cleaning of CI pipes of any dia from first floor to ground floor upto trap and first manhole along the wall, floor, including rodding and removing waste material to a distance not exc 50 mtr all as specified and directed.

Cleaning of man holes of any depth and size including clearing the mouth of outlet/inlet pipes, by taking out accumulated soil, sludge etc mechanically and removal out of MD land and refixing manhole cover all as directed by Engr-in-charge.

Sucking out sewage water through sewage tanker from the manholes/ septic tank/ soakage well in different location and disposal (min 3000 ltr capacity) of out of MD land as directed by Engr-in-Charge.

Cleaning of septic tank any depth any size taking out accumulated soil, sludge any material incl both ends and removal to MD lands and manhole cover refixing all as directed by Engr-in-Charge. Note : (a) Contractor's representative shall attend office of Engr-in-Charge on all working days at 0900 hrs to collect the complaints pertaining to blockage of traps, cleaning of sewage lines, manholes, septic tank and soak wells . In case contractor's representative fails to report Rs 450/- per day will be deducted from the contractor payment for the absent period. (b) complaint slips shall be deposited to the JE concerned after completion of job duly singed by the users. payment shall be made on the basis of complaint slips and site verification by JE/ Engr-in-Charge. (c) Contractor shall provide printed complaint register/ slip as per format given by Engr-in-Charge before commencement of work.

M & L for 10mm thick rendering in CM 1:3 for manholes inner and outer surface in foul condition including taking down old plastered surface and removing from manhole to a lead of min 50 m complete all as specified and directed by Engr-in- Charge.

M & L for providing precast cement concrete coping with plain fair faces incl chamfree, weathering, throating etc type B0, 1:2:4 using 12.5 mm graded aggregate and set in CM 1:4 complete all as specified and directed by Engr-in-Charge.

S & F for sink waste coupling stainless steel 32/40 mm dia complete all as specified.

S&F for PVC waste pipe 32/40mm dia complete all as specified. Make : Prayag/Pearl or equivalent.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges etc.

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia ISI mark or higher and heavy grade conduit fittings and heavy duty accessories with suitable size of sunk type pressed steel terminal box 1.2mm thick for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge for the following. Note: The wiring to be done as per IE rule and maintain colour code accordingly.

One light point point /bell buzzer point controlled by one-one way switch.

One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board

One light point controlled by two, two way switch

All as per Item No 167.00 here in above but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 1.5 Sqmm FRLS copper conductor for continuous earthing complete.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in existing PVC / Steel, concealed and existing MS boxes, mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of following Make of PVC Wire: RR Kabel/KEI/Finolex/L&T. Note: The wiring to be done as per IE rule and maintain colour code accordingly

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) One light point controlled by two, two way switch

All as per Item No 169.00 here in above but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 1.5 Sqmm FRLS copper conductor for continuous earthing complete.

S&F switch piano flush, button type 5 Amp SP 250 V AC complete all as specified & directed.

S&F switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F socket outlet two in one three pin 5 Amp and 15 Amp 2 module 120 W flush type complete al as specified.

S&F Bell switch paino flush button type 5 Amp complete all as specified.

S&F ding dong bell AC 230 V single pole complete all as specified and directed .

S&F switch paino flush button type 5 Amp SP 2 way complete 250 V AC all as specified and directed.

S&F step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts 6 Ampds 400 watts.

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC.

S&F lamp holder,pvc/polycarbonate type with back platesuitable for batten fittings including 9W LED bulb complete all as specified & directed.

M&L in repair sub main wiring with 2 Single core PVC insulated unsheathed FRLS cable 1100 Volts grade heavy duty copper conductor multistranded of size 10 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC conduit medium duty concealed, conduit heavy duty accessories and fittings. Insulated unsheathed FRLS cable copper conductor multistranded of size 10 Sq. mm. as earth wire upto common earth and connected to earth dolly complete all as specified & directed Make of PVC Wire: Havells/KEI/Finolex/L&T.

M&L in repair sub main wiring with 2 Single core PVC insulated unsheathed FRLS cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC conduit medium duty concealed, conduit heavy duty accessories and fittings. Insulated unsheathed FRLS cable copper conductor multistranded of size 6 Sq. mm. as earth wire upto common earth and connected to earth dolly complete all as specified & directed Make of PVC Wire: Havells/KEI/Finolex/L&T.

M & L in replacement for service cable 10 sqmm twin core weather proof aluminium multistranded conductor cable PVC sheathed PVC insulated hanging wire duly connected with earthing and clamp etc from pole to pole complete all as specified and directed.

S&F in repair sheet metal enclosures 240 volt with 200 Amp rated bus bar for double door 8 way DB,s IP-43 IK 09 metal door suitable for one MCB SPN as incoming and 06 MCB SP as out going complete all as specified and directed Make Legrand/Schneider/ABB..

S&F in repair sheet metal enclosures Triple pole and neutral double door 415 Volt 4 way DBs IP-43 IK- 09 Vertical type suitable for 200 Ams rated bus bar & one MCCB 100 Amp as incoming and 12 MCB SP as outgoing complete all as specified and directed Make Legrand/Schneider/ABB.

S&F MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked complete all as specified & directed Make Legrand/Schneider/ABB.

S&F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed Make Legrand/Schneider/ABB.

S&F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed. Make Legrand/Schneider/ABB.

S&F in replacement wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make: Philips cat part No TMC 501P1xT LED 22WP-3241(Tube Batten) and MAS LE$D 1200mm 18W-865-T-81 (Tube) / Wipro Cat part No WI0922208 (Tube Batten) LL13-181-65SE (Tube)/ Havells Cat Part No LUMILINE PLUS BS 20W LED 865 SPCSS (Tube Batten) CRYSTAL 1213T8 DSTL 20W LED 865S GLASS (TUBE DOUBLE SIDE)

Supply, Fixing and testing in replacement LED down lighter recessed mounted 2x2 feet36W ultra modern designed LED luminaire which provide soft light and glair free symmetrical illumination suitable for grid ceiling and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on as per Havells Cat Part no: ENDURASLIMPROPLUS2x2PLR28/36WLED 840MOD or equivelent make of PHILIPs/ CROMPTON all as directed by Engineer-in-Charge.

S&F in replacement LED light fitting 1x10 w bulk head fitting complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size Make:WIPRO CAT PART NO-LW07-141-XXX-57XX or equivelent HAVELLS / CROMPTON

S&F in replacement LED light fitting decorative wall mounting SS brush finish fixture with frosted glass suitable for upto 1x40 watt mini glass lamp with and including one no 12 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable sizeAs per Havells Cat Part NO LHFOAJE1TN1IO60 or equivelent of Bajaj/ Philips.

S&F in replacement mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size . Make Havells Cat No Edgelite or equilent in Philips / Wipro

Supply and Fixing in replacement Integral LED Street Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 40/45 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours, complete all as specified and directed. Make:- Crompton model No. LSTP-45-CDL/ Havells model No. ENDURA PEARLNEOSL 40W LED757PASYTOPC / Philips Cat Part No BRP409LED CW036MRFGIPSUGR and syska SSK-ST-40W including taking out old unserviceable street light.

Supply and fixing of LED tube rod 18/20 Watts single or double sided connections polycarbonate complete incl making connection alteration in existing tube light fitting complete.

Disconnecting electric connection and taking down of ceiling fan / Exhaust fan of any sweep complete carefully for overhauling, removing capacitor, split pins checking of bearings/bush, cleaning the fan blades with cleaning solution, replacing the unserviceable bearing, bush, capacitor , safety split pin and nuts, bolts, washer etc, cutting threading down rod if required, reassembling the ceiling fan complete after greasing/servicing, oiling testing the same making the fan in serviceable condition and refixing/ hanging the same complete all as specified and directed by Engineer-in-Charge (Note: Bush, bearing, capacitor, down rod, hanging clamps, will be paid under relevant item of this Schedule). Cost of split pins, nut bolts and threading of down rod pipe rates are included in quoted rate)

Supply only fan capacitor 2.5 mfd make universal / Asian/Epcos .complete all as specified and directed

Supply only fan capacitor 3.15 mfd complete all as specified and directed make universal / Asian/Epcos

Supply only fan capacitor 4 mfd complete all as specified and directed make universal / Asian/Epcos

Supply only standard ball bearing of ceiling fans of 1200/1400 mm sweep to suitable for different makes of fans of approved quality including necessary greasing of the following:-

For 1200 mm C/Fans NBC or SKF, NORE.

For 1400 mm C/Fans NBC or SKF, NORE.

S&F bulkhead gun metal suitable for ceiling fans 1200/1400 mm sweep/ exhaust fan 300 to 400 mm sweep, cabin fan of any make any size complete all as directed at site.

S&F in replacement of ceiling fan 1200 mm sweep single phase 230 volts double ball bearing with down rod, canopy, blades etc BEE 5 star rated including connecting with twisted three cord flexible copper conductor cable (23/0076/) from ceiling rose to connector of fan complete all as specified and directed. Make : Havells/ Cromption/ Orient/ GEC/ (Note. Old unserviceable ceiling fan will be deposited in E/M store yard)

S&F air ventilation fan 300mm metallic type, heavy duty double ball bearing with louvers single phase 900 RPM, 250V AC including necessary, making hole fixing arrangement on wall with frame 04 nos holdfastner, bolt, washer etc including connection with twisted white three core flexible copper multistranded conductor cable 23/0.0076 from ceiling rose to connector complete all as specified and directed by Engr-in-charge. Make:- Havells cat part No. Ventil Air DXWHT, CG cat No. BRISKAIR or equivalent Orient, (old ventilation fan shall be deposited to MES store yard)

M & L in replacement for providing three core 23/.0076 with copper conductor ceiling fan to ceiling rose and making connection complete all as specified and directed by Engr-in-Charge. Make : Plaza, Finolex and Kalinga.

Supply & Fixing geyser of water storage capacity 25 ltrs, five star rating including PVC connection Nylone braided PVC pipe 2 Nos suitable for hot or cold water, connected to water supply line, including grouting of four Nos holdfastners of suitable size for fixing the geyser and making good disturbed surface to match with existing surface all complete including all electric and water supply connections. Note : Old unserviceable Geyser shall be deposit to E/M Store yard.

S&F Tamper Proof electronic single phase whole current energy meter (LCD Display) 10 Amp to 60 Amp, 240 volt class 1.03 and class 2.05 AC supply including cable connection, proper sealing with lead. The meter shall comply with the latest version of IS-13779 with atleast 2 anti tamper LED indication of line load reversal and earth loading indication. The meter shall work satisfactory with guarantee accuracy as per limit of IS-13779. The meter shall be fixed on existing steel boxes on wall complete all as specified and directed. (Note: Old U/S Meter shall be deposited to E/M store yard). Make:- L&T/ HPL/ Legrand/ SECURE/ BHEL.

Dismantling electric and water connection of the 25 ltr's geyser, taking down from its original position on ground, opening up and removing apparatus plate from the tank, descaling the geyser inner tank and apparatus plate complete, checking for defects, replacement of unserviceable parts such as heating element, syphon assembly, thermostat, rubber gasket etc., reassembling and installation of the geyser into its original position and connecting all electric and water supply connection and testing on completion all as directed by Engineer-in-Charge.(Notes: (i) Heating element, syphon assembly, thermostat, rubber gasket etc if required to be replaced shall be measured and paid separately. (ii) Nut, bolts and hold fastners if required to be replaced shall be deemed to be included in the quoted rates of this item. (iii) Payment for a geyser will be made only once through out the contract period irrespective number of repair carried out in same Geyser.

Supply only heating element any type/size as per site requirement of capacity 2 KW ISI Marked. Make:-Theta/Newton/Dasmesh/Bajaj

Supply only thermostat for geyser long type 11" in length as per site requirement temp setting on 60 degree centigrade ISI Marked, long type complete all as specified and directed. Make: Dashmesh/Indofors/Donfoss/Bajaj

M & L for replacement of old unserviceable pipe with new chromium plated copper connecting pipe 450 mm long with nuts and rubber washers suitable for 15 mm bore pipe complete all as specified and directed by Engr -in- Charge. Make : Polo/ Havells/ Prayag

S&F in replacement of water supply PVC flexible connection Nylon braided with suitable threaded check nut with washer complete suitable for geyser (hot and cold water) 15mm dia alongwith threaded brass nuts and washers 45 cm long complete all as specified and directed. Make:- Polo/Havells/Prayag

S&F three core PVC insulated flexible and over all PVC round cable of size 40/0.0076 with multi stranded copper conductor complete all as specified and directed by Engr-in-Charge. Make : Plaza, National, Shalimar

Supply only syphon assembly for geyser any type of hole (6/7/9) all complete as per existing make & size as per site requirement all complete all as directed by Engr-in-Charge. Make:- Dashmesh/Theta/Newton\/Bajaj

Supply only pressure release valve as per existing make and size geyser spring loaded 15 mm dia complete all as specified and directed.

Supply only rubber gasket as per existing make/size site requirement suitable for 25/50 Ltr capacity geyser complete all as specified and directed.

S&F in replacement Sheet metal enclosure SPN with a two pin and earth plug and socket complete with one 20 amp single pole MCB complete all as specified & directed.

M&L Earthing complete with galvanized steel earth plate electrode 600cmx600cmx6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with a 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm. dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe medium 15 mm. bore and water pipe 20 mm. bore GI light grade with funnel and wire mesh PCC chamber in cement concrete (1:3:6) type C-2 & 75 mm thick RCC (1:2:4) type B1 cover slab reinforced with 8mm TMT bars 100mm c/c both ways complete all as specified & shown in elect plate No. 3 of SSR part I of 2009 and testing on completion.

M/S C S AITHANI

R K BUILDERS

M/s Teg Singh Negi