CWE/CHM-46/2024-25 COMPREHENSIVE MAINT AND REPAIR TO CHAJJA, VENT PIPE IN JCOS/ORS MD ACCN UNDER AGE B/R-I OF GE CHANDIMANDIR AT CHANDIMANDIR MIL STN

Amount

Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and directed by Engineer-in-charge.

M&L for 40 mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar 1:3 as the work proceed, mixed with 5% of crude oil by weight of cement over and including laid bedded over 15 mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-charge.

All as per serial Item no. 2.00 here-in-before but except tiles complete all as specified and directed by Engineer-in-charge.

Material and labour for APP based polymeric membrane 3mm thick, minimum weight 3 kg/Sqm, reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid on primed surface by torch application on and including bituminous primer @ 0.40 ltrs per square metre, complete all as specified and as directed by Engineer-in-charge.

Material & Labour for Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engineer-in-charge.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed by Engineer-in-charge.

Taking down shutter of any description n. exc 1 Sqm each complete all as specified and as directed by Engineer-in-charge.

Taking down shutter of any description exc 1 Sqm but n.exc 2.0 Sqm each complete all as specified and as directed by Engineer-in-charge.

Taking down chowkhat with shutters (without taking off shutter) and removing from site, n. exc 1.50 Sqm each complete all as specified and as directed by Engineer-in-charge.

All as per serial item, No 9.00 here-in-before but exc 1.5 Sqm and n exc 4 Sqm complete all as specified and as directed by Engineer-in-charge.

M&L for Refixing of shutters of any description n exc 1.0 sqm each, in same opening including taking down, easing and adjusting and also refixing hardware as required including renewal of unserviceable screws etc. complete all as specified and directed by Engineer-in-charge.

M&L for Refixing of shutters of any description exc 1.0 sqm but n exc 2.0 sqm each, in same opening including taking down, easing and adjusting and also refixing hardware as required including renewal of unserviceable screws etc. complete all as specified and as directed by Engineer-in-charge.

S&F 125mm x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. including filling of cement concrete 1:3:6 type C-1 in frame complete all as specified and as directed by Engineer-in-charge.

S&F 105 x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. including filling of cement concrete 1:3:6 type C-1 in frame complete all as specified and as directed by Engineer-in-charge.

Supply & Fixing Powder coated aluminium frames (Thickness of powder coating not less than 50 micron) for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and directed by Engineer-in-charge. Note:- sheet glass, wire cloth, etc shall be measured and paid seperately.

S&F 35 mm Plain framed, panelled shutter (two panel) 2nd class HW rail and style with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-charge.

S&F 2nd class hard wood 30 mm thick glazed and skleton shutter open rebated and prepared to receive glass, gauge etc (with sash bars) for edge of framing plane chamfered or rounded fitted without and mitered beed for scrwing glass etc. size of members of shutters as specified in SSR Part-I sec 8 Clause 8.23 (a) fitted to chowkat complete all as specified and as directed by Engineer-in-charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) complete all as specified and as directed by Engineer-in-charge.

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed by Engineer-in-charge. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately

S&F in repair Solid PVC board 20-22 mm thick, interior grade, of white colour, fixed with screws in shelves or kitchen cupboards, shutters including all connnected items complete all as specified and directed by Engineer-in-charge.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed by Engineer-in-charge. Note:- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long period of time.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by Engineer-in-charge.

S&F 300 mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by Engineer-in-charge.

S&F in repair Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-charge.

S&F 150 mm hasp and staples, aluminium anodized including bolt to hinges plate and fixed with screws complete all as specified and as directed by Engineer-in-charge.

S&F of 40 mm dia cupboard brass knob fixed with nut screw and washer fixed in any position, complete all as specified and as directed by Engineer-in-charge.

S&F of PVC body magnetic shutter catcher for kitchen cup boards, fixed with standard steel screws, complete all as specified and as directed by Engineer-in-charge.

S&F 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by Engineer-in-charge.

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 of size 100 mm complete all as specified and as directed by Engineer-in-charge.

S&F 300 mm long mild steel sliding door bolt plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed by Engineer-in-charge.

S&F 200 mm size Aluminium anodized, barrel tower bolt of extruded section complete all as specified and directed by Engineer-in-charge.

S&F 150 mm size Aluminium anodized, barrel tower bolt of extruded section complete all as specified and directed by Engineer-in-charge.

S&F continous (piano) hinges, mild steel bright finish, width of flap 40mm when open, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 18 mm thick PVC louvers and jallies, fixed in aluminium/ mild steel channel frame of approved thickness, including all mouldings fitting and fixtures complete all as specified and directed by Engineer-in-charge.

S&F Mild steel Fe-290 (Gde E-165) Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and including dismantling of old steel door, gate, grill and other steel frame structure etc complete all as specified and directed by Engineer-in-charge.

Demolition of Precast reinforced cement concrete Jali or louvers of any description and in any thickness not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engineer-in-charge.

S&F Mild steel plain black sheet 1.6 mm thick in wall cladding, steel gates and similar work cut to size holes punched including bending or metred angle etc as required complete all as specified and directed by Engineer-in-charge.

Demolition of brick work as in walls/ parapet walls removing grass fungus weed, roots of trees completely, grown on roof/ wall surfaces complete all as specified and directed by Engineer-in-charge.

M&L for Brick work with sub class ‘B’ brick (old size bricks), straight/curved on plan to any radius, built in cement mortar 1:4, as in half brick thick walls complete all as specified and directed by Engineer-in-charge.

Material and labour for brick work with sub class ‘B’ bricks, old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6, complete all as specified and directed by Engineer-in-charge.

All as per serial item No 40.00 but except bricks.

Demolition of un-reinforced cement concrete of any description and in any position including sunken portion, not other wise specially provided for complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster on brick/ stone walls etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

M&L for Rendering 15 mm thick cement plaster in CM 1:4 on brick or concrete surface on inside wall of ventilation shaft of MAP Qtrs, finished even and fair without using extra cement complete all as specified and directed by Engineer-in-charge. Note: Quoted Rates are inclusive of hiring cost of scaffolding, safety equipments etc for working on heights upto four storey MAP Qtr building. No claim whatsoever shall be admissible on this account.

M&L for Preparing Newly Plastered Surfaces of external Walls and applying Two Coats of Cement Base Paint complete all as specified and directed by Engineer-in-charge. Note: Quoted Rates are inclusive of hiring cost of scaffolding, safety equipments etc for working on heights upto four storey MAP Qtr building. No claim whatsoever shall be admissible on this account.

Material and labour, 15 mm thick rendering in Cement and Sand mortar 1:4 over roof slab and sunken portion finished even and fair mixed with water proofing compound,without using extra cement complete all as specified and directed by Engineer-in-charge. NOTE:- WPC will be measured and paid separately.

S&F GI tubing, 40 mm bore, 'medium grade', fixed to wall and ceiling or laying in floor as sunken spout complete all as specified and as directed by Engineer-in-charge.

M&L for Plain cement concrete 1:7:12 type F-2, (using 40 mm graded brick coarse aggregates) as in sunken floor filling and mass concrete complete all as specified and as directed by Engineer-in-charge.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregates) complete all as specified and as directed by Engineer-in-charge.

M&L for 75 mm thick PCC 1:3:6 type B-1 (using 20mm graded stone aggregate) as in sub base complete all as specified and as directed by Engineer-in-charge.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in sub base complete all as specified and as directed by Engineer-in-charge.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilliate demolition complete all as specified and as directed by Engineer-in-charge. Note: Quoted Rates are inclusive of hiring cost of scaffolding, safety equipments etc for working on heights upto four storey MAP Qtr building.

M&L for RCC 1:2:4 type B-1, nominal Mix (using 20mm graded stone aggregates in chajjas, Shelves, Slab, parapet facia etc complete all as specified and as directed by Engineer-in-charge. Note: Quoted Rates are inclusive of hiring cost of scaffolding, safety equipments etc for working on heights upto four storey MAP Qtr building.

M&L for Formwork to chajjas, shelves, slab, troughs and similar items including edges fair finished complete all as specified and as directed by Engineer-in-charge. Note:- Rates are including cost of scaffolding etc for four storey MAP Qtr building.

S&F for TMT Mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new wood based surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint on over a coat of primer complete all as specified and as directed by Engineer-in-charge.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new surface of steel of any description over 10 cm width or girth and applying two coats synthetic enamelled paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old wooden surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-charge.

S&F Steel window, box type, 1.00 mm wall thickness, with glazing bar and openable shutter prepared to recieve sheet glass, complete including cutting holes, four Nos. for each window and making good dismantled portion in PCC (1:2:4) type B-1. including following fittings welded to frame/ shutter complete all as specified and directed.:- (a) Hold fast 150mm out of 25x6mm flat iron made to shape- 04 Nos. each window (02Nos. on each side). (b) Handle of 'Z' section 20mm x 25mm, 100 mm long- 01No. each leaf. (c) MS tower bolt 150 mm long- 02 Nos. each leaf. (d) 'Z' section 20mm x 25mm, 100 mm long stopper 01 No. on each leaf. (e) Cleat 55 mm long of hollow square section 15mm x 15mm of 24 guage wall thickness, welded to hinge of 55 mm size 01 No. per leaf. (f) MS box type hinges of 75 mm size - 02Nos. per leaf. (g) Fabrication & fixing complete.

Note: Glass panes & painting shall be measured & paid separately under respective item.s. Design shall be approved from Engr-in-Charge as existing at site and all as per Drawing before fabrication and bulk order to the manufacturer.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-charge.

S&F 3mm Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engineer-in-charge.

Supply and fixing 3 mm thick figured glass, pin head type and glazing with oil putty of beading in wooden/ PVC/ steel frame in squares n exc 0.5 sqm in each panes complete all as specified and directed by Engineer-in-charge.

Supply & Fixing in repair 3 mm thick sheet glass, ordinary quality, in square n.exc 0.5 Sqm in each panes fixed in any type of frame and glazing with oil putty (or beading) complete all as specified and directed by Engineer-in-charge.

S&F in repair 25 mm dia Stainless Steel curtain rod with fancy brackets/ end brackets/ fennels and fixing stops etc complete all as specified and directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-charge.

M&L for Joint free coloured Glazed ceramic tiles of size 450X 300X 7mm thick in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colour cement to match the shade over and incl 10 mm thick rendering in CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square/ rectangular) joint free tiles, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15 mm thick screed bed or bedding in CM 1:6 complete all as specified and directed by Engineer-in-charge.

M&L for 50 mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/ 100 grade and three part of sand (all by weight) complete all as specified and directed by Engineer-in-charge.

Material and labour 20- 25 mm thick machine cut kota stone flooring 20 to 20 mm thick over cement screed base laid and jointed with neat cement slurry mixed with pigment to match the shade of the slab laid over 20 mm thick bedding layer in cement mortar 1:6 including rubbing and polishing complete all as specified and directed by Engineer-in-charge.

M&L for grinding and polishing surfaces of old Kota/ marble/ granite stone flooring, skirting etc by hand or grinding machine, dusting off the surfaces after grinding, washing and mirror polishing complete all as specified and directed by Engineer-in-charge.

M&L for 18 to 20 mm thick machine cut kota stone as in vertical surfaces such as risers of steps, skirting, dado and pillars etc set and jointed in neat cement slurry and pointed with grey cement mixed with pigment to match the colour of stone slab laid over and including 10 mm thick rendering in cement mortar 1:4 including rubbing and mirror polishing complete all as specified and directed by Engineer-in-charge.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded mechanically crushed stone aggregates) as in sub floor/leveling course to receive topping complete all as specified and directed by Engineer-in-charge.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square/ rectangular) joint free tiles, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed or bedding in CM 1:6 complete all as specified and directed by Engineer-in-charge.

M&L for 16 mm thick, baroda green marble, machine cut laid over & including 15 mm thick average thickness in cement mortar (1:4) bedded and jointed with grey cement slurry and pointed with grout of matching shade including all necessary cutting and machine polishing (table rubbed and polished), as in on kitchen plateform, stair steps and like complete all as specified and directed by Engineer-in-charge.

M&L for rounding to edges of baroda green marble one edge such as in counter type WHB platform etc. to the entire satsfaction of Engineer-in-Charge complete all as specified and directed by Engineer-in-charge.

M&L for Rendering 15mm thick cement plaster in CM 1:4 on brick or concrete surface on wall finished even and fair without using extra cement incl taking down existing plaster complete all as specified and directed by Engineer-in-charge. Note: Quoted Rates are inclusive of hiring cost of scaffolding, safety equipments etc for working on heights upto four storey MAP Qtr building. No claim whatsoever shall be admissible on this account.

M&L for Rendering 10 mm thick cement plaster in CM 1:6 on brick or concrete surface of wall finished even and smooth without using extra cement incl taking down existing plaster complete all as specified and directed by Engineer-in-charge.

M&L for preparation of Newly Plastered Surfaces of internal wall and applying two Coats of oil bound distemper on wall over a coat of primer complete all as specified and directed by Engineer-in-charge.

M&L for Rendering 5 mm thick cement plaster in CM 1:3 on brick or concrete surface of ceiling, finished even and smooth without using extra cement complete including taking down existing plaster complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfacces of ceilings and applying three coat of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preperation of new surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old plastered or unplastered surfaces and applying two coat of oil bound distemper complete all as specified and directed by Engineer-in-charge.

M&L for Complete removal of existing treatment and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed by Engineer-in-charge.

M&L for Prepration of old surfaces of walls includinng scrapping down smoke ,soot,and efflorescent salts and treatings oil and gresy spots, brooming down or steel wire brushing removing nails making good holes, cracks etc on plastered or unplastered surfaces and applying one coat of oil bound distemper (white or tinted as ordered) complete all as specified and directed by Engineer-in-charge.

M&L for Repairs to leaking joints of CI pipes/ traps/ fittings etc after taking out old jointing material lead/ cement, cleaning the joint thoroughly and filling new material Drip seal/ lead/ cement and sealing the joints with joint sealing compound (Dr Fixit or equivalent) and making the installation completely leak proof complete all as specified and directed by Engineer-in-charge.

Note : (i) The work pertains to the trap/ drain pipes/ fittings of the WC / bath of MAP quarters installed under side of the roofs. (ii) All the joints of pipes/ traps/ fittings of one WC/ bath shall be measured as one unit and payment shall be made for each WC / bath as “Each Job” (iii) The rates shall be inclusive of providing scaffolding and safety equipments etc as required.

Taking down old steel tubing & connection including cleaning for refixing for 15mm bore pipe complete all as specified and directed by Engineer-in-Charge.

Taking down old steel tubing & connection including cleaning for refixing for 20mm bore pipe complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore GI tubing, 'medium grade', with all fittings to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

S&F 20 mm bore GI tubing, 'medium grade', with all fittings to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Cutting chases, pining in, making good to facings where required and pointing in cement mortar 1:3, for concealed water tubing etc and making good, cutting exc 10 cm but n exc 20 cm girth complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Bib taps, of 15mm bore, cast copper alloy with crutch or butter fly handle, chromium plated complete all as specified and directed by Engineer-in-charge.

S&F in repairs of 15 mm Angular Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions fancy type chromium plated, complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC connection pipe, 15 mm dia with PTMT nuts of length 450 mm complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair central hole Basin Mixer, 15 mm size for mixing hot & cold water, cast copper alloy, chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe including 450 mm long braided connection pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair 15mm bore brass CP mixer for mixing hot & cold water screwed down for iron fixed etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair chromium plated, fancy type shower rose with swivel joints, 125 mm dia with CP arm and fixing to steel pipe 15 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F in repair Stop valves, concealed type, cast copper alloy, chromium plated, screwed down, high pressure with capstan heads screwed both ends for iron pipe or for union and fixed 15 mm bore complete all as specified and as directed by Engineer-in-charge.

S&F in repair Stop valves 20 mm bore, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and directed by Engineer-in-charge.

Supply and fix in repair white vitreous China wash hand basin (Flat back) of size 550 x 400 mm fixed on and including new brackets complete including, 32 mm size brass chromium plated waste coupling, chain and plug and porcelain stopper, etc complete all as specified and directed by Engineer-in-charge.

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat cover, white, closed pattern with flat bottom, and cover with aluminised hinging device, brass chromium plated Jet shower with one meter long flexible pipe including all connection complete all as specified and directed by Engineer-in-charge.

Supply and fixing vitreous china squatting pan, “Orissa” pattern size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe complete including trap, set with cement as in repair complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and wastes, overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm incl cantilever brackets and connection to union, pipe, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 750 mm x 600 mm plate rack, made out of 1.00 mm thick stainless steel sheet with steel shelves and hanging arrangement for utensil, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair PVC valveless syphonic action type flushing cistern, low level, white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC bend for squat/pedastal pattern etc, complete all as specified and directed by Engineer-in-Charge.

M&L for Mild steel works as in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; will ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 290-0 Gd-165 complete all as specified and directed by Engineer-in-charge.

Supply and fixing 500 litres capacity rotational moulded polyethylene water storage tanks ISI marked (Cylindrical vertical with closed top) double layered, screwable lid, hoisted and fixed in position, including supply and fix tank nipple, ball valve 20mm PTMT, including dismantling of existing water tanks and removing from site all as specified in SSR Part-I complete all as specified and directed by Engineer-in-charge.

Disconnecting existing tanks, Exc 250 Ltr and n. exc 500 ltr capacity tank, setting aside (or lowering if required) for repairs, cleaning, etc. including Cleaning and removing all scale and dirt, etc. from tanks any height and form mouths of circulating pipes, etc and hoisting if required, reconnecting and re-fixing in position, complete all as specified and directed by Engineer-in-charge.

Supply & Fixing in repair 20 mm bore ball valve high pressure PTMT with epoxy coated aluminium rod & high density polythene float ball and fly nut screwed for iron pipe complete all as specified and directed by Engineer-in-charge.

Material and labour for cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregates) as in roof padding, coping, for fixing of holdfast complete all as specified and directed by Engineer-in-charge.

Supply only Integral water proofing compound, ISI Marked, complete all as specified and directed by Engineer-in-charge.

M&L for providing 25 mm thick precast cement concrete louvers and jallies, type B-0 1:2:4 (using 12.5 mm graded stone aggregates) measured solid, including all mouldings but excluding frame and set in CM 1:4 complete all as specified and directed by Engineer-in-charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks etc. including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

S&F 75 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls/floor in ventilation shaft of MAP qtrs, in any length complete all as specified and directed by Engineer-in-charge. Note: Quoted Rates are inclusive of hiring cost of scaffolding, safety equipments etc for working on heights upto four storey MAP Qtr building. No claim whatsoever shall be admissible on this account.

S&F 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls/floor in ventilation shaft of MAP qtrs, in any length complete all as specified and directed by Engineer-in-charge. Note: Quoted Rates are inclusive of hiring cost of scaffolding, safety equipments etc for working on heights upto four storey MAP Qtr building. No claim whatsoever shall be admissible on this account.

S&F 110 mm dia PVC (SWR) bends, Reducer, socket any radius complete all as specified and directed by Engineer-in-charge.

S&F 75 mm dia PVC (SWR) bends, Reducer, socket any radius complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair PVC (SWR) floor trap, 75 mm bore, plain with grating incl jointing with solvent cement, fixed as in repair complete all as specified and directed by Engineer-in-charge.

Supply and fixing 75mm bore PVC (SWR) junction (single T) equal or unequal complete all as specified and directed

Supply and fixing 110mm bore PVC (SWR) junction (single T) equal or unequal complete all as specified and directed

M/S Gupta and Sons (BID ID -3075436)