REPAIRS TO B/R ITEMS OF CERTAIN BLDGS OF OFFICER QTRS AT AFS ADAMPUR

Amount

BR WORKS

M&L for Cement concrete, type B-0 (1:2:4), using 12.5 mm graded crushed stone aggregates as in lintels up to 1.5 metre clear span, bed blocks of holdfast, copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete all as specified and specified & directed.

M&L for Reinforced cement concrete, type B-1, (1:2:4), using 20 mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, and in shelves and the like complete all as specified and directed.

M&L for Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified and directed.

M&L for Brick work in half brick thick wall using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:4), complete all as specified and directed.

M&L for Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) with fair finished flat surfaces of concrete, complete all as specified and directed.

S&F, Factory made, 30 mm thick, first class hard wood, plain framed, hammer marked, skelton shutter (two panel to receive wire gauge) with lock rail . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

S&F, Factory made, 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, with 0.9mm decorative laminate type 1 of surface finish, colour and pattern as approved by GE and fixed with approved adhesive on both sides, ISI marked, complete all as specified and directed.

S&F factory made solid PVC moulded Door shutter, 28 to 30 mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm prelam PVC sheet on back face, supplying and fixing at site as per specification and drawing complete all all as specified and directed.

S&F, Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick wood grain colour PVC sheet reinforced with mild steel square tube, suppling & fixing in opening, complete all as specified and directed.

S&F, Factory made single extrudeed WPC (Wood Polymer Composite) solid plain flush door shutter of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), clacium carbonate and natural fibres (Wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gm) having minimum density of 650 kg/Cu.m and screw withdrawl strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50N/Sq.mm, modulus of elasticity 850 N/Sq.mm and resitance to spread of flame of Class A category with property of being termite/borer proof, water / moisture proof and fire retardant and fixing complete all as specified and directed.

S&F, Factory made single extruded WPC (Wood Polymer Composite) solid door/ window /Ceosetory windows & other Frames/Chowkhat of size 63x51 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gm) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/Cu.m, screw withdrawl strength of 2200N Face & 1100 N (Edge), minimum compressive strength of 58 N/ Sq.mm, modules of elasticity 900 N/Sq.mm and resistance to spread of flame of Class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed.

M&L for Plywood 18 mm thick, 12 ply type BB commercial BWR confirming to IS: 303 fixed on frame, IN REPAIRS, complete all as shown and directed.

S&F, Factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified and directed.

S&F, Factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3±0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. complete all as specified and directed..

S&F, Factory made uPVC white colour casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed. NOTE: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.

NOTES APPLICABLE TO SERIAL ITEM 14 TO 17: - (i) After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality. (ii) Glass or wiremesh shall be paid separately) (iii) For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F, Stainless steel sliding door bolt with hasp and staple (bolt type) and fixing round typeclips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 250 mm long complete. MAKE: PRAYAG CAT NO. SLD-1210 or equivalent make mentioned in Appndix 'B'

S&F, Stainless steel, barrel tower bolt, 150 mm long, with stainless steel screws, complete all as specified. MAKE :PRAYAG CAT NO. TBS-2150 or equivalent make mentioned in Appndix 'B'

S&F, Stainless steel 100mm long butt hinges with stainless steel screws, ISI marked complete all as specified and directed. MAKE: PRAYAG CAT HG-3414 or equivalent make mentioned in Appendix 'B'

S&F, Mild steel ordinary rat tail rod pattern helical door spring 250 mm long including roller and roller plate, complete all as specified and directed.

S&F, Stailess steel, handle, 125 mm long, curve shapewith stainless steel screws, complete all as specified. MAKE: PRAYAG CAT NO. DHC-2125 or equivalent make mentioned in Appndix 'B'

S&F, Stainless steel conduit 20 mm bore, cut to size and erected in position as curtain rod on backets, with & including SS decorative finials & brackets, fixed to walls with PVC rawl plugs & SS screws, IN REPAIRS, complete all as specified and directed.

S&F, Double leg aluminium anodised door stopper with rubber foot, ISI marked and fixed to bottom rail of doors with steel screws, complete all as specified and directed.

S&F, Stainless steel 100mm size auto soft closing hydraulic hinges fixed with stainless steel screws, ISI marked complete all as specified and directed.

S&F, Stailess steel, handle, 125 mm long, curve shapewith stainless steel screws, complete all as specified and directed. MAKE: PRAYAG CAT NO. DHC-2125 or equivalent make mentioned in Appndix 'B'

S&F, Mild steel chromium plated solid handle, 100mm suitable for cupboard shutter, complete all as specified and directed.

M&L for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples, complete all as specified and directed

M&L for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples IN REPLACEMENT, complete all as specified and directed.

M&L for Framed mild steel work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel work as in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) quality confirming to grade Fe-290-Gde E-165, complete all as specified and directed.

S&F, Factory made pre painted pressed steel frames, conforming to IS, having profile 105 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete, complete all as specified and directed.

S&F, Factory made pre painted pressed steel frames, conforming to IS, having profile 125 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete all as specified and directed.

S&F, Factory made steel windows with side hung shutter with glazng bars each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded,complete.

S&F, Factory made steel windows with side hung shutter without glazng bars each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded,complete.

S&F, Steel windows or ventilators, fixed type made of MS sheet 1.25 mm thick box type (primer coated), ERW hollow 'P' section of size 60mm x 25 mm complete all as specified and directed. NOTES APPLICABLE TO SERIAL ITEM NO. 35 TO 37: (a) Profile section used under these items shall be 'P' tube as shown in drawing No. CE/AF/STD-170/07, CE/AF/STD-171/07 and CE/AF/STD-172/07 as applicable.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, complete all as specified.

M&L for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs / trusses by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M&L for Seamless calcium silicate ceiling 8mm thick made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish, complete all as specified. NOTE: Frame work & hangers for ceiling shall be measured and paid separately)

S&F, Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/ cladding to wall, bent to curve fixed with self tapping screws complete all as specified and directed.

M&L for 4mm thick aluminium composite panel with and including 2 mm thick cushioning and 1mm thick aluminium sheet on both side of colour as approved by GE, fixed in wall cladding complete all as specified and directed.

M&L for aluminium tubes as in framework for fixing wall cladding of sections as approved by GE, complete all as specified and directed.

Water Proofing Treatment to RCC roofs comprising of : -

Taking down existing water proofing treatment (any no. of layers) from RCC roofs including cleaning the surface including flashings and junction of parapet etc. with wire brushing & water to the entire satisfaction of EIC, complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20 mm graded stone crushed aggregate, laid to slope as directed by Engineer in Charge over RCC roofs as padding, complete all as specified and directed.

M&L for Rendering 15 mm thick (Average thickness) rendering on roof surface including flashings and junction of parapets etc., finished even and fair in cement mortar (1:4), using water proofing compound as recommended by manufacturers after brushing cement slurry @ 1.20 kg/Sq. m, complete all as specified and directed. NOTE: Supply only WPC will be measured & paid for separately under respective item of BoQ.

M&L for APP based polymeric membrane laid on primed roofs & flashing by forced application using Butane torch and sealing all joints on primed surface by applying hot blown industrial grade bitumen @ 85/25 @ 1.20 kg/Sq.m over a coat of bitumenous primer @ 0.40 litre per square metre over clean RCC/plastered roof surfaces & flashings complete all as specified and directed.

M&L for 40 mm thick brick tiles bedded over 15 mm thick cement mortar (1:4), and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on APP membrane complete all as specified and directed.

M&L for Making benching with PCC (1:2:4) type B-0 (using water proofing compound) along side walls adjoining to roofs, in CONCAVE SHAPE, complete all as specified and directed. NOTES: (i)WPC will be measured and paid for separately under respective item of BoQ. (ii) For Performance Guarantee of Water Proofing Treatment refer PS clause 11.5.

Supply only water proofing compound (WPC), ISI marked, complete all as specified.

M&L for 18/19 mm thick high density moisture resistant (HDMR) board, flat pressed, fixed as in modular kitchen cabinets, cupboards, shelfs or similar works with necessary screws complete all as specified and directed.

M&L for Decorative laminates type I, 0.9-1 mm thick of surface finish, colour and pattern as approved , fixed with approved adhesive complete all as specified and directed.

M&L for High quality solid colour (matching shade) PVC edge banding tape not less the 3 mm thick having 18/19 mm width fixed with approved adhesive to HDMR board complete all as specified and directed.

M&L for Ball bearing runners 45mm telescopic channel (20 inch) full extension load capacity 50 kgs complete all as specified and directed.

M&L for 25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded crushed stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

M&L for 75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, and joints shall be sealed with joint sealing comound grade 'A' complete all as specified and directed.

M&L for 100 mm thick, cement concrete type D-2, 1:4:8 using 40 mm graded stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

M&L for Granite jet black shade, 15-18 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), complete all as specified and directed.

M&L for Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified.

M&L for Glazed ceramic coloured tiles 7mm thick, area of each tile exc. 0.17 Sq.m but n. exc. 0.19 Sq.m on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for Coloured glazed ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exc. 0.42 Sq.m but n. exc. 1 Sq.m, on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified & directed.

M&L for Coloured non skid dark shade (double charged) ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exc. 0.11 Sq.m but n. exc. 018 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified & directed.

M&L for Coloured non skid dark shade (double charged) ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.38 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified & directed.

M&L for First quality, vitrified ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exc. 1.00 Sq.m but n. exc. 1.50 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for First quality, vitrified ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exc. 1.00 Sq.m but n. exc. 1.50 Sq.m, on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 50mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for 80 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 50mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for Endura/ Parking vitrified paving coloured tiles 19 to 20 mm thick (square/ rectangular) area of each tile exc. 0.11 Sq.m but not exc. 0.18 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed in grout of matching shade, laid over and including 15 mm thick bedding layer in cement mortar (1:4) complete all as specified and directed.

Repairing of RCC projection chhajjas, roof, facia etc by necessary preparation. Scraping cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC with cement concrete Type A-0 (1:1.5:3) and reinforcement with chicken mesh of weight not more than n.exc 3 kg/Sq.m (if reqd) with or without facia and finished with cement and sand mortar (1:3) using coarse sand and work in patches of area n.exc 5 Sq.m and thickness of RCC member n.exc 70 mm incl necessary formwork at any height/location complete all as specified and directed. NOTE: The rate quoted by the contractor shall included for chicken mesh, scaffolding and necessary formwork upto triple storey bldg.

M&L for Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling in cement mortar (1:3), complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:6) complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), mixed with water proofing compound as per manufacturers instructions, complete all as specified and directed. NOTE: WPC will be measured and paid for separately under respective item of BoQ.

M&L for One coat of oil bound distemper/ interior acrylic distemper on old decorated ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

M&L for One coat of Plastic emulsion paint on old decorated ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

M&L for Two coats of oil bound distemper/ interior acrylic distemper on new undecorated ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

M&L for Two coats of plastic emulsion paint on new undecorated ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

M&L for Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer.

M&L for Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed). (b) Two coats of plastic emulsion paint over and including a coat of interior primer.

M&L for Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer.

M&L for Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of plastic emulsion paint over and including a coat of interior primer.

M&L for Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed).complete all as specified. (b) Two coats of exterior acrylic emulson over and including a coat of water based exterior primer complete all as specified.

M&L for Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer.

S&F, Sheet glass 4 mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5sqm in each pane complete all as specified and directed.

S&F, Figured glass 4mm thick ordinary quality and glazing with oil putty in squares n. exc. 0.5 Sq.m in each pane complete all as specified and directed.

S&F, Plain tinted sheet glass, 5-6 mm thick, ordinary quality duly sticked with solar control reflective type film, having thickness not less than 25 micron and fixed air tight with neoprene packing & almn glazing clips, for aluminium/uPVC sections, complete all as specified and directed. NOTE: Almn glazing clips & neoprene packing will be measured & paid for under respective item of aluminium door/windows/partition.

M&L for 10mm thick clear toughened glass with clear visibiity and fixed with clear or without aluminium/uPVC frame with and including all necessary fixing material as approved by GE glazing with putty or fixed with beads complete all as specified and directed. .

M&L for 10 mm thick Toughned glass as in hinged doors, partitions automatic doors (area of one shutter not exc. 1.50 Sqm) and similar work including cutting to shape, drilling holes required , Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and 300mm stainless steel handle (2 handle on each leaf) , complete all as specified and directed

M &L for One coat (finishing coat) of synthetic enamel paint over wood and wood based surfaces of any description not other wise described over 10cm width or girth, including preparation of surfaces, complete all as specified.

M &L for Two coats of synthetic enamel paint over & including a coat of pink primer over wood and wood based surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

M &L for One coat (finishing coat) of synthetic enamel paint over old painted steel or iron surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

M&L for Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel or iron surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

M &L for Preparation of wooden surface including cleaning with sand paper and applying two coats of french polish to achieve glossy finish and including minor fillings with putty as required complete all as specified and directed.

Disconnecting existing tanks of capacity exceeding 500 litre but not exceeding 1000 litre, setting aside (or lowering if required) for cleaning/roof repair etc. and hoisting, reconnecting and re-fixing in position after necessary cleaning by removing all scale and dirt etc. including cleaning mouth of circulating service pipes complete all as specified and directed

S&F, 500 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN REPAIRS, complete all as specified including the following acessories: - (i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, IN REPAIRS, suitable for 20 mm bore GI pipe, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, IN REPAIRS, complete all as specified. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS, complete all as specified.

S&F 1000 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, complete all as specified including the following acessories: - (i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, suitable for 20 mm bore GI pipe, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, complete all as specified. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP/outer edge of roof, complete all as specified & directed.

S&F Steel tubes 15 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified & directed.

S&F Steel tubes 20 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified & directed.

S&F Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, , screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified & directed. MAKE: CERA Cat No. F2002201 or equivalent make mentioned in Appendix 'B'.

S&F concealed stop valve/cock, cast copper alloy, chromium plated, with adjustable wall flange, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified & directed. MAKE: CERA Cat No. F2002361 or equivalent make mentioned in Appndix 'B'.

S&F Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified & directed. MAKE: CERA Cat No. F1005151 or equivalent make mentioned in Appendix 'B'.

S&F chromium plated Wall mixer (3-in-1) with arrangement for both telephonic hand shower and overhead shower with bend pipe, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified & directed. MAKE: CERA Cat No. F1005151 or equivalent make mentioned in Appendix 'B'.

S&F, Sink mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: CERA Cat No. F1012511GG or equivalent make mentioned in Appendix 'B'.'.

S&F 15mm bore Deck mounted pillar sensor tap for tabletop washbasins with tap hole screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified & directed. MAKE: CERA Cat No. F6010101 or equivalent make mentioned in Appendix 'B'.

S&F 15mm bore Wall mounted sensor tap, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified & directed. MAKE: CERA Cat No. F6010106 or equivalent make mentioned in Appendix 'B'.

S&F 150 mm size overhead ABS shower with cast copper alloy chromium plated arm 195 mm long with bend of 45 degree with flange of CP brass and fixed in position, complete all as specified & directed. MAKE: CERA Cat No. F7010111SSor equivalent make mentioned in Appndix 'B'.

S&F Vitreous China wash down water closet wall hang pan (pedestal pattern), white ISI marked, with & including stainless steel body Jet spray (L-bend) with1.50 metre long braded tube tube, soft close slim PVC seat & cover and uPVC 'S trap, complete all as specified & directed. MAKE OF EWC: CERA Cat No. 1043137 or equivalent make mentioned in Appendix 'B'.

S&F Vitreous China one piece wash down water closet pan (pedestal pattern), white ISI marked, with & including stainless steel body Jet spray (L-bend) with1.50 metre long braded tube tube, soft close slim PVC seat & cover and uPVC 'S' trap, complete all as specified & directed. MAKE OF EWC: CERA Cat No. S1013208 or equivalent make mentioned in Appendix 'B'.

S&F Vitreous China wash hand basin, counter type,snow white circular, oval shape of size 470 x 470 x 200 mm including fixing acessories like 32mm dia CP waste coupling & PVC collapsible waste pipe, complete all as specified & directed. MAKE: CERA Cat No. S2030115 or equivalent make mentioned in Appndix 'B'.

S&F, Vitreous China wash hand basin, white, flat back, size 550 x 400 mm, ISI marked, including fixing acessories like rag bolts etc. with CP waste coupling half or full threaded suitable for & including 32 mm size PVC solid waste pipe, IN REPAIRS, complete all as specified. MAKE: PRAYAG Cat No. 4645 or equivalent make mentioned in Appendix 'B'

S&F Toilet Paper Holder with flap guard complete all as specified & directed. MAKE: CERA Cat No. F5015110CH or equivalent make mentioned in Appendix 'B'.

S&F Liquid soap dispensor complete all as specified & directed. MAKE: CERA Cat No. F5014111CH or equivalent make mentioned in Appendix 'B'.

S&F Health Faucet with 1.25mtr flexible tube and wall hook complete all as specified & directed. MAKE: CERA Cat No. F8030103 or equivalent make mentioned in Appendix 'B'.

S&F Concealed PVC flushing cistern 10 litre capacity, syphonic action type, , dual flush, size mentioned in catalogue ISI marked with all fixing acessories, complete all as specified & directed. MAKE: CERA Cat No. B1110104 & B1120109H or equivalent make mentioned in Appendix 'B'

M&L 5-6 mm thick looking glass fixed over not less than 6 mm thick PVC ply and approved shade PVC beading not less than 15 mm wide alround with and including all fixing acessories, complete all as specified & directed.

S&F Glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long with brass brackets and fixed to wall with chromium plated brass screws and rawl plugs, complete all as specified & directed. MAKE: CERA Cat No. F5005101 or equivalent make mentioned in Appendix 'B'.

S&F, Corner glass shelf with two racks with brass brackets fixed to wall with SS screws and PVC rawl plugs, IN REPAIRS, complete. MAKE: CERA Cat No. F5005201 or equivalent make mentioned in Appndix 'B'.

S&F, Bathroom mirror Cabinet (PTMT alloy) of size 450 x 350 x 100 mm with SS screws and fixed in position, IN REPAIRS, complete. MAKE: PRAYAG Cat No. 557 or equivalent make mentioned in Appndix 'B'.

S&F Brass chromium plated towel rail 500-600 mm long, fixed to wall with SS screws and PVC rawl plugs, complete all as specified & directed. MAKE: CERA Cat No. F5014103CH or equivalent make mentioned in Appndix 'B'.

S&F 175 mm long body ABS bottle trap chromium plated complete all as specified & directed. MAKE: CERA Cat No. F8060404AB or equivalent make mentioned in Appendix 'B'.

S&F Stainless steel round slotted grating with frame, 100 mm size fixed in position with cement joints, complete all as specified & directed.

S&F Stainless steel connections with SS nuts, 600 mm long, complete all as specified & directed. MAKE: CERA Cat No. F8070402 or equivalent make mentioned in Appndix 'B'.

S&F Waste coupling with ceramic pop-up push type (full thread) 32 mm complete all as specified and directed. MAKE: CERA Cat No. F8050351BK or equivalent make mentioned in Appendix 'B'.

S&F Stainless steel kitchen plate rack of sheet thickness not less than 0.61 mm overall size 786 x 760 x 254 mm, fixws to wall with PVC plugs and SS screws ,IN REPLACEMENT complete all as specified and directed. MAKE:PRAYAG Cat No. 557 or equivalent make mentioned in Appndix 'B'.

S&F Stainless steel sink double bowl type, matt finish made out of SS sheet not less than 1 mm for kitchen & including plug waste pipe, washers conncting union etc including necessary fixing accessories, overall size 1143mm x 510mm x 203 mm with bowl size 510 mmx 405mmx 203mm,IN REPLACEMENT complete all as specified and directed. MAKE:PRAYAG Cat No. P-1350D or equivalent make mentioned in Appndix 'B'.

S&F stainless steel soap dish,IN REPLACEMENT complete all as specified and directed. MAKE:CERA Cat No. F5006106 or equivalent make mentioned in Appndix 'B'.

M&L for uPVC pipes 75 mm external dia, type-A, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed to walls as Rainwater pipes, IN REPAIRS, complete all as specified and directed.

M&L for uPVC pipes 75 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified and directed.

M&L for uPVC pipes 110 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified and directed.

M&L for uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 75 mm external dia, IN REPAIRS, complete all as specified and directed.

M&L for uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 110 mm external dia, IN REPAIRS, complete all as specified and directed.

M&L for uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 75 mm external dia, IN REPAIRS, complete all as specified and directed.

M&L for uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 110 mm external dia, IN REPAIRS, complete all as specified and directed.

M&L for uPVC floor trap, suitable for uPVC soil waste discharge pipes 75 mm ext dia, embedded in PCC type B-1(1:2:4), IN REPAIRS, complete all as specified and directed,

DISMANTLING/DEMOLITION WORKS

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sq.m each and removing from site all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sq.m but not exceeding 4.00 Sq.m each and removing from site all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each and removing from site complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each, including stacking at directed location and refixing the same on original or new location after resecuring or easing & adjusting, complete all as specified and directed.

Taking down cement plaster of any description on brick walls or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking up or down steel tubing 15 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Demolition brickwork or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and pavings not excceding 15cm thickness (above or below ground level) complete all as specified and directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Dismantling boarding, any description, fixed in any position complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings, complete all as specified and directed.

Demolition of mud phuska in roofs, of thickness not more than 200 mm including plaster and leeping plaster complete all as specified and directed.

Dismantlig brick tiles in roof laid dry and pointed in cement mortar complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, gypsum, POP, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description, complete all as specified and as directed

Notes: Amount of credit for retrieved materials is mentioned in tender documents in pdf form which will be deducted while acceptance of tender offline.

BHARAT ENTERPRISES (BID ID -3317323)

J.K & Company (BID ID -3315304)

M/s Sahib and Company (BID ID -3314933)