REPAIR/ REPLACEMENT / MAINT OF EXTERNAL ELECTRIC SERVICE SUCH AS 2/4 POLE STRUCTURES, SWITCH GEARS, FEEDER BOXES AND OH CONDUCTORS/ UG CABLES AT SECTOR 1 AND SOA AREA UNDER THE AOR OF GE DEOLALI

Amount

Excavation in trenches in hard/dense soil not exc 1.5 mtr wide and not exc 1.5 mtr deep for laying of electric cable, pole foundation and stays etc and getting out, trimming the sides, forming bottom surfaces to required level complete all as specified and directed.

Returning, filling in, approved earth including spreading, levelling, watering and well ramming in layers n.exc 250mm thick after cables are laid and tested all as specified and directed.

Removing excavated material (Surplus soil) to a distance not exc 50m and depositing where directed at level not exc. 1.5m above the starting point all as specified and directed.

M&L for sand cushioning to under ground cable by providing with a layer of 05 cm thick before laying of cable and 18 cm after laying of cable in trenches complete all as specified and directed. Note :- Punned down thickness shall only be measured.

M & L for flyash bricks having minimum compressive strength 75 Kg/Sqcm laid in trenches for cable protection etc complete all as specified and directed.

M&L for Cutting through existing bituminous road /PCC/floor/approx size width 50cm X 60cm depth along cross section of the road for laying of GI tubing/RCC pipe for encasing of cable and repairing the road to match with the original finish complete all as specified and directed.

M&L for cement concrete 1 : 4 : 8 type D-2 using 40 mm graded stone aggregate as in foundtion for pole including necessary form work all as specified and directed

M & L for cement concrete 1 :3 :6 type C2 location / situation using 20 mm graded stone aggregate as in coping incl necessary form work all as specified and directed.

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 150 Sqmm 3.5 Core

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 120 Sqmm 3.5 Core

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 95 Sqmm 3.5 Core

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 50 Sqmm 3.5 Core

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 35 Sqmm 3.5 Core

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 25 Sqmm 4 core

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 16 sq mm 4 core

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 10 Sqmm 4 core

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 2 core 10sqmm

M & L for Tubes "light grade" galvanised iron, laid under roads/drain, fixed to poles, walls, with flat iron clamps bolts/nuts/washers of 100 mm dia bore complete all as specified and directed.

M & L for Tubes "light grade" galvanised iron, laid under roads/drain, fixed to poles, walls, with flat iron clamps bolts/nuts/washers of 80 mm dia bore complete all as specified and directed.

M & L for Tubes "light grade" galvanised iron, laid under roads/drain, fixed to poles, walls, with flat iron clamps bolts/nuts/washers of 50 mm dia bore complete all as specified and directed.

M & L for Tubes "light grade" galvanised iron, laid under roads/drain, fixed to poles, walls, with flat iron clamps bolts/nuts/washers of 40 mm dia bore complete all as specified and directed.

Dismantling and taking down any type of LT poles from any location all as specified and directed

Supply, Install and errect in true vertical position steel tubular swaged poles 9m long complete with MS base plate of 6mm of size 300mm X300mm finial taper plug,pole cap,bolts,nuts and washers screws,pole made out of ERW MS tubing as per IS-1161 and pole shall be as per IS-2713 Part II type 410SP-31 complete including one coat of red oxide zinc chrome primer and two coats of aluminium paint for exposed surfaces and two coats of black bitumenous paint for portion embedded in concrete complete all as specified and as directed Note: Excavation and earth work ,PCC in foundation /plinth block/coping shall be measured and paid for separately

Dismantling of cross arms of MS fabricated complete with all accessories viz nut, bolts, washer etc. complete all as specified and directed.

Supply and fixing cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed including a coat of red oxide primer one under and one finishing coat of aluminium paint complete all as specified and directed.

Supply and fix in replacement HT 11 KV outdoor non-linear type lightening arrestor with mountings, accessories complete fixed on cross arms of two polestructure/GI flat strip and connect with same size of ACSR conductor encased in PVC alkathine pipe with all fittings connected to earth stripwith nut, bolt, washer transmission class having discharge capacity of 5 kilo Amps and suitable for working pressure 9 KV complete all as specified and directed .

Dismantling and Taking down of Gang operating Device including Drop Out Fuse from Two/ Four pole structure All as specified

Supply, installation and testing HT gang operated air break switch 11 KV, 3 pole vertically mounted type, mechanically operated, mounted on steel frame with operating mechanism, worked from ground level for current upto 200 Amps with drop out fuse elements of required capacity, GOD/switch having 100 MVA rating at 11 KV and 12 insulators suitable for 11 KV, 50 C/s including mounting on HT poles and necessary electrical connections complete all as specified and directed.

S&F drop-out fuse unit expulsion type for out door air break gang operated switch, single pole mounted on and including insulators and jumpers for 11kv working pressure fixed to and including MS channel with nuts, bolts and washers etc, synthetic bounded fuse tube complete with line cap suitable for current carrying capacity upto 100Amps all as directed.(Set of three)

Repair/overhauling of air break switch complete by replacing stationary, and moving contacts, flexible copper cord, GI nuts, bolts, etc incl alingment for smooth functioning from ground level all as req uired at site and as directed.

Supply and fixing cable termination end joint Heat shrinkable out door type suitable for HT 11 KV cable XLPE aluminium conductor of size 120 sqmm x 3 core and including taking out cable from faulty portion in any situation/position complete all as directed. Make : Denson/Raychem/Mseal

Supply and fixing cable termination end joint Heat shrinkable indoor type suitable for HT 11 KV cable XLPE aluminium conductor of size 120 sqmm x 3 core and including taking out cable from faulty portion in any situation/position complete all as directed. Make :- CCI / Asian Cables / Gloster / Finolex.

Supply, jointing and testing staright through joint Heat shrinkable type with jointing kit suitable for HT 11 KV XLPE size 120 sqmm x 3 core in any situation/position complete all as directed. Make : Denson/Raychem/Mseal

Supply, jointing and testing staright through joint Heat shrinkable type with jointing kit suitable for LT 1100 Volt graded XLPE size 150 to 185 sqmm x 3.5 core in any situation/position complete all as directed. Make : Denson/Raychem/Mseal

Supply, jointing and testing staright through joint Heat shrinkable type with jointing kit suitable for LT 1100 Volt graded XLPE size 70 to 120 sqmm x 3.5 core in any situation/position complete all as directed. Make : Denson/Raychem/Mseal

Supply, jointing and testing staright through joint Heat shrinkable type with jointing kit suitable for LT 1100 Volt graded XLPE size 25 to 50 sqmm x 3.5 core in any situation/position complete all as directed. Make : Denson/Raychem/Mseal

Re stringing, streaching and binding with insulator, ACSR conductor ( for single conductorWeasel /ferret/Mink) on HT/LT Poles including providing of necessary jumpers, connecting all existing incoming and out going connections, trimming of trees approximately 2 mtr around conductor etc all as specified & directed.

Supply, laying & testing XLPE insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor 11000 volts grade (E), of size 3 Core 120 sqmm complete all as specified.

Supply and fix in replacement disc insulator porcelain viterous, 150 mm high and 150 mm dia white /brown / green two in series assembly for tension clamps for conductor working pressure 11000 volts

Supply and fix in replacement Pin type insulator porcelain viterous,white , brown or green insulator including one galvanised mild steel spindle, two galvanised iron wahsers and one galvanised iron nut, 65 mm dia for 1100 volts grade complete all as specified and directed

Supply and Fixof Street Light fitting LED 70 W madeup of pressure diecast aluminium housing with high power LEDs with secondary optics,IP66 protection and impact resistance of IK07 with all assessories,/ electric connectins all as specified. Make: Havells Cat Pt No- ENDURACITYLINERNEOSL70WLED757PASYBOTG or Philips/ Bajaj / Wipro

S&F street light bracket made out of GI tubing 40mm bore, medium grade, 1.5 metre long bent to shape as directed, including suitable MS clamp with MS bolts, nuts and washer fixed to steel tubular pole/PCC pole duly painted with two coats of aluminium paint complete all as specified and as directed.

M&L for MCCB of 4 pole of capacity 63 to 100 Amps 415 Volts with breking capacity 18 KA complete as in repairs all as specified and directed Make:- L&T/ Legrand/ Scheinder/ Siemens

M&L for MCCB of 4 pole 200 Amps adjustable type, 415 Volts, with breking capacity 25 KA complete as in repairs all as specified and directed Make:- L&T/ Legrand/ Scheinder/ Siemens

M&L for MCCB of 4 pole 250 Amps adjustable type, 415 Volts, with breking capacity 25 KA complete as in repairs all as specified and directed. Make:- L&T/ Legrand/ Scheinder/ Siemens

M&L for MCCB of 4 pole 400 Amps adjustable type, 415 Volts, with breking capacity 50 KA complete as in repairs all as specified and directed. Make:- L&T/ Legrand/ Scheinder/ Siemens

Taking down and S&F Thermo plastic street light junction box 280 x 170 x 115 mm complete with 4 way connector - 01 No,6 amps SP MCB - 01 No ( LEGRAND / ABB), fixing clamp (M.S.) and water tight polymide cable gland for each connection incl taking down u/s complete all as specified and as directed at site. Make of box : Sintex / HENSEL / National

M&L earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6.3 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron strip 32 x 6 mm size by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 40 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 6 mm dia MS round bars @ 15 cm c/c both way for cover and MS frame etc., complete all as specified.(set of two) NOTE: The unit rate includes earth strip and protection pipe upto (maximum 7.5 metre from earth plate) earth point/test point.

Supply, erection, testing and commissioning of outdoor type LT Bus Bar Chamber box, platform mounted, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos stepped type Aluminium bus bars 600Amps capacity for looping & branch connection system .The chamber shall be painted with powder coated paint. The bus bar chamber shall be provided with suitable Neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 (a) The bus bar chamber shall be made out of 3.0mm thick CRCA mild steel sheet and 3.00mm thick gland plate , front door (01 layer) and rear Door (01 layer) opening facility and 4 side slanting canopy type roof on top and angle iron padastal frame 600mm high above ground level. The bus bar chamber shall be provided with ventilation facility in the form of louvers for better heat dissipation. (Note : The bus bar chamber Box shall be designed in such a way that adequate workable space is made available inside the compartments and the size of the chamber shall not be less than 600mm height (without base frame & canopy), 600mm width and 500mm depth).

Supply, erection, testing and commissioning of outdoor type LT Bus Bar Chamber box, platform mounted, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos stepped type Aluminium bus bars 400Amps capacity for looping & branch connection system .The chamber shall be painted with powder coated paint. The bus bar chamber shall be provided with suitable Neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 (a) The bus bar chamber shall be made out of 3.0mm thick CRCA mild steel sheet and 3.00mm thick gland plate , front door (01 layer) and rear Door (01 layer) opening facility and 4 side slanting canopy type roof on top and angle iron padastal frame 600mm high above ground level. The bus bar chamber shall be provided with ventilation facility in the form of louvers for better heat dissipation. (Note : For Ser Item No- 36 &37. The bus bar chamber Box shall be designed in such a way that adequate workable space is made available inside the compartments and the size of the chamber shall not be less than 600mm height (without base frame & canopy), 600mm width and 500mm depth).

S & F automatic street light switch using NATURE SWITCH for automatic switching of street Lights based on LUX level of Natural Light. The sensor (Nature Switch) along with suitable Power Contactor, MCB and Support Terminals should be enclosed in pole/wall mountable enclosure made of Rust Proof, Electric Shock Proof, Termite proof and FR grade special moulding compound (Sintex make SMC Junction box) conforming to IP54 degree of ingress. The contactor, MCB and Circuit wiring should suitable enough to take load of 12 KW equally distributed over 3 Phase (4KW /Phase) Contactor Rating : 40 Amps MCB (single-pole) Rating :63 Amps 3 Nos Make : Nature Switch : Kakatiya Energy Systems Pvt Ltd Hyderabad / BAJAJ

M&L for scrubbing out old paint, rust etc from LT Steel tubular pole of any size and making smooth and even surface then painting with one coat of anti corrosive paint and two coat of superior quality aluminium paint on entire exposed portion of pole structure and writing Abbreviated feeder name in 2 " size with white paint on black base all as directed at site(work shall be completed in the stipulated period as directed by Engineer -in-charge.

M&L for scrubbing out old paint, rust etc from HT two pole structure and making smooth and even surface then painting with one coat of anti corrosive paint and two coat of superior quality aluminium paint on entire exposed portion of two pole structure and writing feeder name 2 " size with white paint on black base all as specified and directed.

M&L for scrubbing out old paint, rust etc from HT four pole structure and making smooth and even surface then painting with one coat of anti corrosive paint and two coat of superior quality aluminium paint on entire exposed portion of two pole structure and writing feeder name 2 " size with white paint on black base all as specified and directed.

Note: Amount of sch of credit of Rs. 47,321.00/- will be deducted from total amount of BOQ.

AGRAWAL ASSOCIATES

DHARMESH ENTERPRISES

Rama Electricals

KOYNA ENGINEERS PVT LTD

M/S S.N ENTERPRISES

n.p.shinde electricals

Maruti Abhiyantriki

M/S K. K. Construction