PROVISION OF 4 URINALS, 2 TOILETS,WHB,OHT, SOAKAGE WELL, SEPTIC TANK NEAR MI ROOM OF MH MEERUT UNDER GE(U) MEERUT CANTT.

Amount

M&L construction of septic tanks of 50 users capacity complete all as specified and shown in drawaing No. TD-217.

M&L construction of soakwell 1.8M dia Marked "d" and 3 M effective depth marked "h" and over all depth 4 M complete all as specified and shown in drawing No. TD-309

M&L Brickwork in cement mortar 1:6 with sewer bricks straight or curved on plan exc 6 m mean radius for manholes/ septic tanks/ soakwell etc. complete all as specified.

S&F 15mm bore Cast copper alloy Chromium plated Angle stop cock ( one way) long thread with wall flange , screwed down , high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified .

S&F Fancy type Bib taps , CP, cast copper alloy with crutch or butterfly handle , screwed down , scrwed for iron pipe or for brass ferrule and fixed 15 mm bore complete all as specified.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft /loose soil surfaces formed to required slope, gradient, camber, and superelevation etc. complete all as specified.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes,pier holes, laying of pipe and cables etc. but not exceeding 10 sqm on plan including dressing/trimming sides and levelling/grading & ramming bottom of excavation and getting out in soft/loose soil complete all as specified.

Returning ,filling in , including spreading , levelling , watering and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified.

M&L Earth filling under floors/ pathways or in foundations including spreading , levelling, watering and consolidation in layers not exceeding 25 cm thick each layer complete all as specified.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L broken bricks hardcore of gauge n exc. 63 mm , deposited , spread and levelled in layer n exc. 15 cm thick, watered and rammed to a true surface complete all as specified.

M&L plain cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundations / mass concrete complete all as specified.

M&L plain cement concrete type C1 ( 1:3:6) using 20 mm graded stone aggregate as lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in (roof kerbs or mud stops, rounded or cmamfered on edges), water troughs and the like including weathering , slightly rounded or chamfered angles and throating, as directed including necessary formwork complete all as specified.

M&L Reinforced Cement concrete M-25 ( Design Mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified.

M&L Reinforced Cement concrete M-25 ( design mix) as in slabs supported on walls, beams and columns , in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L Reinforced Cement concrete in cement concrete M-25 ( Design Mix) as in beams, cantilevers, bressumers, lintels not excd 1.5 m span complete all as specified.

M&L Reinforced Cement concrete M-25 ( Design Mix) as in reinforced Cement concrete ( Design mix) in columns, pillars, piers, posts and struts complete all as specified.

Supply only Integral water proofing compound complete all as specified and directed.

M&L Brick work with old size fly ash bricks., straight or curved on plan exc 6 m mean radius , built in CM 1:6, complete all as specified and directed.

M&L Brick work with old size fly ash bricks., straight or curved on plan exc 6 m mean radius ,half brick thick wall, built in CM 1:4, complete all as specified and directed.

M&L 40 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in damp proof course to horizontal or vertical surfaces including necessary formwork mixed with water proofing compound complete all as specified.( water proofing compond shall be measured and paid separately).

Use and waste of formwork to sides of concrete foundations, footings, bases of columns , raft and raft beams, sides and soffits ( if any) of foundation and plinth beams; and similar work; vertical or to batter surfaces finished fair in forms complete all as specified.

Use and waste of formwork to flat soffits of suspended deck slabs, floor slabs, landings and similar work; not exceeding 200 mm thick ( Horizontal or sloping) surfaces finished fair as specified in SSR Part-I Clause 4.11.16.2(b) as specified complete all as specified.

Use and waste Formwork to flat sides and soffits of floor or roof beams, beam haunchings, girders,bresumers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc. surfaces finished fair complete all as specified.

Use and waste of Formwork to sides of Square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions surfaces finished fair as per clause 4.11.16.2 (b) of SSR Part I complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) con-sisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be cov-ered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain col-our PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification complete all as specified and directed.

S&F Solid PVC door frame of size 50mmx47 mm made out of 5 mm plain colour PVC sheet reinforced with Mild steel square tube complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 150 mm length of bolt, ISI marked complete all as specified.

S&F stainless steel medium weight butt hinges ,ISI-12817 marked , 100 mm long and fixed

S&F Aluminium handles, cast type anodised 'D' shaped , 125mm long ISI marked all as specified.

M&LHigh strength deformed bars or twisted bars ( TMT) 10 mm dia and over as in reinforcement , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. or higher complete all as specified.

M&L High strength deformed bars/twisted ( TMT ) 6mm dia. and over up to and including 10 mm dia. stirrups, spacers and binders as in reinforcement , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. Or securing with clips complete all as specified.

S&F presssed steel frame steel windows duly fitted with side hung glazed and gauzed shutters including mild steel stay, box type hinges, mild steel tower bolts 100mm long 02 Nos per leaf, 150mm long mild steel handle 01 No per leaf, mild steel grills made out of 12mm mild steel square bars, complete all as specified and shown in drawing No. TD-88 sheet 1/17 to 17/17.

S&F Steel windows or ventilators , fixed type, with glazing bars complete all as specified.

M&L for providing water proofing treatment on inaccessible roof surfaces ( horizontal and vertical surfaces) through authorised applicator of manufacturers comprising (a)Cleaning of new rendered surfaces properly and drying the surfaces.(b) Applying a coat of Oxidised bitumen based solvent primer @ 0.30 Kg/square metre (c) applying hot applied bitumen industrial grade 85/25 @ 1.20 Kg/sqm (d) Providing 3mm thick APP (Atactic Polypropylene) modified water proofing membrane reinforced with polyster non woven fabric (weighing not less than 3.0 Kg/sqm , side and overlaps not ess than 75mm and 100mm , sealed and bonded to the surfaces with torch application. (e) Applying two coats of bituminous aluminium paint @ 0.10 litre per square metre (min) as per manufacturers instructions complete all as specified.

M&L 18mm thick Machine cut Kota stone slab risers,skirting, dado and pillar etc over 10mm thick screed in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to give high gloss (mirror) finish complete all as specified. The unit rate quoted by Contractor shall to be included for screed ( Screed bed shall not be measured and paid separately).

M&L Plain cement concrete type C1 (1:3:6), using 20 mm graded crushed stone aggregate,50 mm thick , as in plinth protection, top surfaces finished eevn and smooth without using extra cement ,laid in alternate bays with 6 mm wide and 40 mm deep joints filled in with mastic filling comprising 1 part of heated bitumen 85/25 grade and 3 parts of sand (all by weight). in concrete bays at corners and turning points and also in between walling and plinth protection co finished fair and even , complete all as specified.

M&L 7mm thick Non Skid plain coloured ceramic tiles (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screeding in CM 1:6 complete all as specified ( screed bed shall not be measured and paid separately).

M&L glazed ceramic coloured tiles of size 250mm to 350mm X 400-450mmxx7mm thick , on vertical surfaces such as dados , skirting and risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screeding in CM 1:4 complete all as specified. ( The quoted rate shall deem to be includued for screeding and shall not be measured and paid separately).

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces , in cement and sand mortar 1:6 , top surfaces finished even and smooth without using extra cement complete all as specified

M&L rendering 5 mm thick on fair faces of brick work or concrete surfaces of ceiling , in cement and sand mortar 1:4 , top surfaces finished even and smooth without using extra cement complete all as specified

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces , in cement and sand mortar 1:6 , top surfaces finished even and smooth without using extra cement complete all as specified.

M&L rendering 15 mm thick on stone masonry surfaces or surface other than fair face of brick work or on one side of lathing, in cement and sand mortar 1:4 , top surfaces finished even and smooth without using extra cement complete all as specified

M&L Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes cement and sand mortar 1:6 complete all as specified

M&L for Preparation of old decorated plastered or unplastered surfaces of walls by complete removal of existing treatment and applying Two coats of white wash complete all as specified including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

M&L preparation of newly plastered /unplastered surfaces of walls by applying distempering with distemper oil emulsion , two coats, white or tinted over a coat of chalk whitening primer including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

M&L preparation of new plastered / unplastered surfaces of walls and applying two coats with cement base paint , white or tinted over one coat of cement paint primer ( before application of cement base paint) including and washing floors, etc. , of drops and splashes complete all as specified .

M&L 15 mm nominal bore Mild steel galvanised water tubing , medium grade (ISI) marked , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified.

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade (ISI) marked , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified.

S&F PTMT connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

M&L 150 mm internal dia Salt - glazed stone ware drain pipes, Class 'SP2' laid in trenches and jointed as specified.

M&L Plain cement Concrete ( 1:4:8) type D2 bed to 150 mm bore drain pipes including packing under , and haunching against the sides of pipes after they are laid and tested ;in complete all as specified.

S&F Gunmetal , gate valves, with iron wheel head, screwed both ends for 20 mm bore dia. iron pipe and fixed complete all as specified.

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. .(Minimum weight 20mm-210 gms.) complete all as specified.

S&F Rotational moulded poly-ethylene water storage tanks (ISI marked) ( cylinderical vertical with closed top ) 500 litres capacity ,hoisted and fixed in position complete all as specified.

S&F 110 mm bore PVC (SWR) pipes single socketed ISI marked IS-13592 , type 'B', pressure rating 6 Kg /cm, in any length with rubber ring joints/ solvent ( conforming to IS-14182) cementing joints laid in trenches or in floors type complete all as specified.

S&F 110 mm bore PVC (SWR) pipes single socketed ISI marked IS-13592 , type 'B , pressure rating 6 Kg /cm square in any length with rubber ring joints/ solvent ( conforming to IS-14182) cementing joints fixed to walls complete all as specified.

S&F PVC (SWR) bends ( ISI marked) 110 mm bore with access door complete all as specified

S&F PVC (SWR) Branch piece , single ( single Y ) equal or unequal 110mm bore complete all as specified

M&L PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 110 mm dia. outlet complete all as specified.

S&F Vitreous china , 'Orrisa' pattern , size 580x440 mm white, with integral foot rests Water closet including S&F PVC 'P' trap, connection to to flushing pipe,antisyphonage pipe, trap set in and including concrete, provision of lime concrete bedding (1:2:5) min 150 mm thick alround , making good floor to match with the existing complete all as specified.

S&F Vitreous china Urinal, Half stall type, white ( excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing , bedding urinal against wall in cement mortar 1:2 , , pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. ( Exclusive of fixing supply pipe to flushing cistern , trap and waste pipe) complete all as specified.

S&F 32 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fixed complete all as specified.

S&F 32 mm dia discharge pipe waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms) complete all as specified.

S&F stainless steel grating 125 mm dia complete all as specified.

S&F Low level flushing cistern, moulded from virgin poly propylene 10 litre capacity including provision of 32 mm dia PVC flush pipe and making connections, ISI marked or equivalent of other make specified complete all as specified and directed.

S&F vitreous china wash basin (WHB) , white , flat back , size 550mmx400mm( Model No. 0471 of parryware or equivalent of other make specified) including mild steel/ CI brackets, brass Chromium plated 32 mm dia waste fittings for glazed basins etc. with long screw shanks and fly nuts , flange end embedded in red lead cement , PVC connections 15 mm size with PTMT nuts of length 450mm, 32mm dia LDPE waste pipe of required length, CP brass pillar tap fancy type-01 number including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply pipe complete all as specified .

M&L earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick, burried directly in to ground ( earth pit) not less than 2.25 metres deep below GL with top edge of earth plate ot less athn 1.50 m below ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, connected to GI lead wire of 4 mm dia.(7.50 m Long) by means of nuts, bolts and washers, checknuts of GI and protected by the GI pipe light grade 15 mm nominal bore (7.5 m long) for earth lead wire and watering pipe light grade of 20 mm nominal bore, 0.63 mm thick G I sheet funnel , wiremesh, earthing test point etc complete including necessary earth work and excavation in any type of soil , PCC 1:3:6 type C1 earth pit and Cast iron frame and cover with lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I.

S&F Miniature circuit breakers SP, 6 to 32 Amps, 240 Volts , 10 KA, 'B' curve rating and to be housed in sheet metal enclosures ( distribution boxes) and making connections with suitable copper lugs complete all as specified and directed :- (Note :- Proper and suitable size cable lugs to be fixed with Miniature circuit breakers are included in unit rate of each Miniature circuit breakers of any rating).

S&F house service brackets House service Bracket ( hook type) complete with 3.0 m long G.I. pipe 40 mm dia. Med. Grade , two nos. 90 degree bends , M.S hook and stay or guy complete all as specfied.

M&L point wiring for one light point/fan point/bell point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed (FR) cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and including continuous earth wire of 1.5 sqmm nominal cross sectional area multistranded copper conductor , PVC insulated unsheathed (FR) and connecting to earth dolly and brass screws, washers etc. complete all as specified :- Note:- The rate quoted against this item shall be deemed included for cutting chases for concealed conduit and boxes etc including making good disturbed surfaces to match with the existing.)

S&F polycarbonate Switch piano flush type, SP, 6 Amps, one way ( ISI) marked complete all as specified.

S&F Isolator single pole , 240 V, 40 amps complete all as specified.

S&F epoxy powder coated distribution box, SPN, 4 ways, 240 volts, IP-43 ,metal double door for MCB , grouted flush to walls including making good disturbed surafces of wall to match the adjoining surfaces complete all as specified and directed.

M&L polycarbonate insulated body ceiling rose 6A, 50x20mm dia with three terminals, ISI maked fixed complete all as specified.

S&F Light emitting Diode (LED) tube light fitting surface/ pendent mounting decorative box type AC 220-240V, 50 hz, CRCA body with acrylic diffuser 20 watt, 4' long, and making connections with and including 23/.0076 flexible cord of required length from ceiling rose to connector complete all as specified and directed.

S&F Energy saving & environment friendly LED street light fitting made out of pressure die cast anodised aluminium housing with polycarbonate or flat glass optical cover with Penut lens,25 Watt to achieve B1 class road illumination as per IS: 1944 and as per national lighting code using each LED >1 watt and <3 watt , LED chip efficiency >= 135 Lumens/Watt, CRI>70, CCT 5000K to 6500K with LED life span at 70% of light output >50000 hours with suitable driver 140V to 270V universal type, with bult in surge protection >5KV, 50 Hz +/- 3% , pf 0.95, THD <10% with system efficiency >85 lumens/ Watt and power efficiency >=90% and overall IP 65 or better , driver and luminaire shall comply LM-79/IS:16106 and making connections with and including 3 core 2.50 mm stranded copper conductor cable, PVC insulated and PVC sheathed from junction BOx to luminaire complete all as specified and directed.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor , served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by (existing insulating hangers not more than 1 metre apart including 4 mm suspension wire), one twin core 6 sqmm flat cable complete all as specified and directed.

Supplying , installing, testing, commissioning exhaust fan, heavy duty, 300 mm sweep, 230/240 Volts, AC , 50 Hz, 1400 rpm with mild steel louvers and other accessories, making holes in walls to the required shape and size, grouting Mild steel bolts in walls of length not less than 125 mm and 12 mm dia. with nuts and washers complete all as specified .

SA construction co.

mohanlal gupta

Maa Vaishno Enterprises