Loading
Loading…
Loading…
Tender Value
₹2.8 Cr
EMD Value
₹5.6 L
Closing Date
14 Sept 2026, 3:00 pm
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
90 days
Expenditure
Capital (Works)
ALD/CONST
17 conditions · 6 needing a document upload
10.2. Financial Eligibility Criteria: The tenderer must have minimum average annualcontractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tenderin crores of Rupees N= Number of years prescribed for completion of work for which bidshave been invited. The average annual contractual turnover shall be calculated as anaverage of "total contractual payments" in the previous three financial years, as per theaudited balance sheet. However, in case balance sheet of the previous year is yet to beprepared/ audited, the audited balance sheet of the fourth previous year shall be consideredfor calculating average annual contractual turnover. The tenderers shall submit requisiteinformation as per Annexure-VIB, along with copies of Audited Balance Sheets duly certifiedby the Chartered Accountant/ Certificate from Chartered Accountant duly supported byAudited Balance Sheet.
Balance Sheet Declaration- Balance sheet for the 4th previous year (i.e. FY 2022-23 or asapplicable) as per para 10.2 of GCC-2022 shall be considered in evaluation of financialeligibility criteria only when it is clearly certified in Annex-VI B or a self declared certificate to be attached duly signed by chartered accountant and the tenderer that the balance sheet oflast financial year (i.e. FY 2025-26 or as applicable) has not been audited/yet to beprepared. If, balance sheet of last financial year (i.e. FY 2025-26 or as applicable) is not yetaudited/ prepared ,then NIL position to be uploaded.
10.1 Technical Eligibility Criteria: (a)The tenderer must have successfully completed orsubstantially completed any one of the following categories of work(s) during last 07 (seven)years, ending last day of month previous to the one in which tender is invited: (i)Threesimilar works each costing not less than the amount equal to 30% of advertised value of thetender, or (ii)Two similar works each costing not less than the amount equal to 40% ofadvertised value of the tender, or (iii)One similar work costing not less than the amountequal to 60% of advertised value of the tender. (b)(1) In case of tenders for composite works(e.g. works involving more than one distinct component, such as Civil Engineering works,S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure,superstructure etc.), tenderer must have successfully completed or substantially completedany one of the following categories of work(s) during last 07 (seven) years, ending last dayof month previous to the one in which tender is invited: (i)Three similar works each costingnot less than the amount equal to 30% of advertised value of each component of tender, or(ii)Two similar works each costing not less than the amount equal to 40% of advertised valueof each component of tender, or (iii)One similar work each costing not less than the amountequal to 60% of advertised value of each component of tender. Note for b(1): Separatecompleted works of minimum required values shall also be considered for fulfillment oftechnical eligibility criteria for different components. (b)(2)In such cases, what constitutes acomponent in a composite work shall be clearly pre-defined with estimated tender cost of it,as part of the tender documents without any ambiguity. (b) (3) To evaluate the technicaleligibility of tenderer, only components of work as stipulated in tender documents forevaluation of technical eligibility, shall be considered. The scope of work covered in otherremaining components shall be either executed by tenderer himself if he has workexperience as mentioned in clause 7 of the Standard General Conditions of Contractorthrough subcontractor fulfilling the requirements as per clause 7 of the Standard GeneralConditions of Contract or jointly i.e., partly himself and remaining through subcontractor,with prior approval of Chief Engineer in writing.
However, if required in tender documents by way of Special Conditions, a formal agreementduly notarised, legally enforceable in the court of law, shall be executed by the maincontractor with the subcontractor for the component(s) of work proposed to be executed bythe subcontractor(s), and shall be submitted along with the offer for considering sublettingof that scope of work towards fulfilment of technical eligibility. Such subcontractor mustfulfill technical eligibility criteria as follows: The subcontractor shall have successfullycompleted at least one work similar to work proposed for subcontract, costing not less than35% value of work to be subletted, in last 5 years, ending last day of month previous to theone in which tender is invited through a works contract. Note: for subletting of work costingup to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by theRailway. In case after award of contract or during execution of work it becomes necessaryfor contractor to change subcontractor, the same shall be done with subcontractor(s)fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract,with prior approval of Chief Engineer in writing. Note for Item 10.1: Work experiencecertificate from private individual shall not be considered. However, in addition to workexperience certificates issued by any Govt. Organisation, work experience certificate issuedby Public listed company having average annual turnover of Rs 500 crore and above in last3 financial years excluding the current financial year, listed on National Stock Exchange orBombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closingof tender, shall also be considered provided the work experience certificate has been issuedby a person authorized by the Public listed company to issue such certificates. In casetenderer submits work experience certificate issued by public listed company, the tenderershall also submit along with work experience certificate, the relevant copy of work order, billof quantities, bill wise details of payment received duly certified by Chartered Accountant,TDS certificates for all payments received and copy of final/last bill paid by company insupport of above work experience certificate.
Definition of similar nature of work :-Any Signalling or Telecom work.
Bidder has to upload requisite information as per Annexure V(A) along with the offer
41 conditions · 11 needing a document upload
Stamp Duty fee for Bank Guarantee (for bid security) should be paid which shouldbe 0.5% of the Bid security or Rs.10,000/-, whichever is less or as per latest/revisedstate policy of UP state
The tenderer whether sole proprietor / a company or a partnership firm / jointventure (JV) /registered society / registered trust / HUF / LLP etc if they want to actthrough agent or individual partner(s), should submit along with the tender, a copyof power of attorney duly stamped and authenticated by a Notary Public or byMagistrate in favour of the specific person whether he/they be partner(s) of the firmor any other person, specifically authorizing him/them to sign the tender, submit thetender and further to deal with the Tender/ Contract up to the stage of signing theagreement except in case where such specific person is authorized for abovepurposes through a provision made in the partnership deed / Memorandum ofUnderstanding / Article of Association /Board resolution, failing which tender shallbe summarily rejected. A separate power of attorney duly stamped andauthenticated by a Notary Public or by Magistrate in favour of the specific personwhether he/they be partner(s) of the firm or any other person, shall be submittedafter award of work, specifically authorizing him/them to deal with all othercontractual activities subsequent to signing of agreement, if required. Note: A Powerof Attorney executed and issued overseas, the document will also have to belegalized by the Indian Embassy and notarized in the jurisdiction where the Power ofAttorney is being issued. However, the Power of Attorney provided by Bidders fromcountries that have signed the Hague Legislation Convention 1961 are not requiredto be legalized by the Indian Embassy if it carries a conforming Apostille certificate. (Note:In case of non-submission of above documents, offer may be summarilyrejected)
The tenderer will give full information ( in annexure-A) as to the date of retirementof such Engineer or gazetted officer from the said service and as to whetherpermission for taking such contract, or if the Contractor be a partnership firm or anincorporated company, to become a partner or director as the case may be, hasbeen obtained by the tenderer or the Engineer or officer, as the case may be fromthe President of India or any officer, duly authorized by him in this behalf, shall beclearly stated in writing at the time of submitting the tender,if a tenderer is - i) be aretired Engineer of the gazetted rank or any other gazetted officer working beforehis retirement, whether in the executive or administrative capacity or whetherholding a pensionable post or not, in the Engineering or any other department ofany of the railways owned and administered by the President of India for the timebeing, OR ii) being partnership firm / joint venture (JV) / registered society /registered trust etc have as one of its partners/members a retired Engineer of thegazetted rank or any other gazetted officer working before his retirement, OR iii)being an incorporated company have any such retired Engineer of the gazettedrank or any other gazetted officer working before his retirement as one of itsdirectors AND in case where such Engineer or officer had not retired fromgovernment service at least 1 year prior to the date of submission of the tender
If a tenderer or Contractor being an individual, have member(s) of his family or inthe case of partnership firm/ company / joint venture (JV) / registered society /registered trust etc. one or more of his partner(s)/shareholder(s) or member(s) ofthe family of partner(s)/shareholder(s) having share of more than 1% in thetendering entity employed in gazetted capacity in the Engineering or any otherdepartment of the railway, then the tenderer at the time of submission of tender,will inform the authority inviting tenders the details of such persons. ( in annexure-A)
An undertaking shall be submitted by sole proprietorship firm, HUF, JV, LLP,Company registered under companies Act 2013 that he/they are not blacklisted ordebarred by Railways or any other Ministry / Department of the Govt. of India fromparticipation in tenders / contracts as on the date of opening of bids, either in theirindividual capacity or in any firm in which they were / are partners. Concealment /wrong information in regard to above shall make the contract liable fordetermination under Clause 62 of the General Conditions of Contract.(Note: Eachmember must sign separately in case of JV/Partnership firm/LLP.).(Note: IN case ofnon submission of above documents, offer may be summarily rejected).
In case of partnership firm an undertaking shall be submitted by all partners of thepartnership firm that they are not blacklisted or debarred by Railways or any otherMinistry / Department of the Govt. of India from participation in tenders / contractsas on the date of submission of bids, either in their individual capacity or in any firmin which they were / are partners. Concealment / wrong information in regard toabove shall make the contract liable for determination under Clause 62 of theGeneral Conditions of Contract. (Note: In case of non-submission of abovedocuments, offer may be summarily rejected)
Please submit your bank details i.e.Name of the Bank along with Bank Branch Code,Account Number, IFSC Code, and PAN Number
Please furnish list of plant and Machinery available on hand own and proposed to beinducted own and hired to be given separately for the subject work.
Please furnish list of Works on hand indicating Description of Work, Contract Value,Approximate value of balance work yet to be done and Date of award.
Please furnish list of personal, organization available on hand and proposed to beengaged for the subject work.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Whether the cost of tender form is submitted in hard copy if uploaded as a scannedcopy in website
Whether the cost of Bid Security is submitted in hard copy if uploaded as a scannedcopy in website.
16.(1) Security Deposit: The Security Deposit shall be 5% of the contract value. TheBid Security submitted by the Contractor with his tender will be retained/encashedby the Railways as part of security for the due and faithful fulfilment of the contractby the Contractor. Provided further that, if Contractor submits the Cash or TermDeposit Receipt issued from a Scheduled commercial bank of India or irrevocableBank Guarantee Bond from a Scheduled commercial bank of India, either towardsthe Full Security Depositor the Part Security Deposit equal to or more than BidSecurity, the Railway shall return the Bid Security, to the Contractor. Balance ofSecurity Deposit may be deposited by the Contractor in cash or Term DepositReceipt issued from Scheduled commercial bank of India or irrevocable BankGuarantee bond issued from Scheduled commercial bank of India, or may berecovered at the rate of 6% of the bill amount till the full Security Deposit isrecovered. Provided also that in case of defaulting Contractor, the Railway mayretain any amount due for payment to the Contractor on the pending "on accountbills" so that the amounts so retained (including amount guaranteed throughPerformance Guarantee) may not exceed 10% of the total value of the contract. TheIrrevocable Bank Guarantee submitted towards Security deposit shall be initiallyvalid up to the stipulated date of Maintenance period plus 60 days and shall beextended from time to time, depending upon extension of contract granted in termsof Clause 17A and 17B of the Standard General Conditions of Contract. Note:Security Deposit deposited in cash by the Contractor or recovered from the runningbills of a Contractor or submitted by contractor as Term Deposit Receipt(s) can berefunded/returned to the contractor, in lieu of irrevocable Bank Guarantee bondissued from scheduled commercial bank of India, to be submitted by him, for anamount equal to or more than the already available Security Deposit, providedhowever that, in a contract of value less than Rs. 50 Crore, such refund/ return ofthe already available Security Deposit is permitted up to two times and in acontract of value equal to or more than Rs. 50 Crore, such refund / return of thealready available Security Deposit is permitted up to three times
16.(4) Performance Guarantee:- The procedure for obtaining PerformanceGuarantee is outlined below: (a)The successful bidder shall have to submit aPerformance Guarantee (PG) within 21 (Twenty-one) days from the date of issue ofLetter of Acceptance (LOA). Extension of time for submission of PG beyond 21(Twenty-one) days and upto 60 days from the date of issue of LOA may be given bythe Authority who is competent to sign the contract agreement. However, a penalinterest of 12% per annum shall be charged for the delay beyond 21(Twenty-one)days, i.e. from 22ndday after the date of issue of LOA. Further, if the 60thdayhappens to be a declared holiday in the concerned office of the Railway, submissionof PG can be accepted on the next working day. In all other cases, if the Contractorfails to submit the requisite PG even after 60 days from the date of issue of LOA, thecontract is liable to be terminated. In case contract is terminated railway shall beentitled to forfeit Bid Security and other dues payable to the contractor against thatparticular contract, subject to maximum of PG amount. In case a tenderer has notsubmitted Bid Security on the strength of their registration as a Startup recognizedby Department of Industrial Policy and Promotion (DIPP) under Ministry ofCommerce and Industry, DIPP shall be informed to this effect. The failed Contractorshall be debarred from participating in re-tender for that work.
(b)The successful bidder shall submit the Performance Guarantee (PG)in any of the following forms, amounting to 5% of the original contractvalue: - (i)A deposit of Cash; (ii)Irrevocable Bank Guarantee;(iii)Government Securities including State Loan Bonds at 5% below themarket value; (iv)Pay Orders and Demand Drafts tendered by anyScheduled Commercial Bank of India; (v)Guarantee Bonds executed orDeposits Receipts tendered by any Scheduled Commercial Bank ofIndia; (vi)Deposit in the Post Office Saving Bank; (vii)Deposit in theNational Savings Certificates; (viii)Twelve years National DefenceCertificates; (ix)Ten years Defence Deposits; (x) National DefenceBonds and (xi) Unit Trust Certificates at 5% below market value or atthe face value whichever is less. Also, FDR in favour of Sr. DFM (freefrom any encumbrance) may be accepted. (c)The PerformanceGuarantee shall be submitted by the successful bidder after the Letterof Acceptance (LOA) has been issued, but before signing of the contractagreement. This P.G. shall be initially valid upto the stipulated date ofcompletion plus 60 days beyond that. In case, the time for completion ofwork gets extended, the Contractor shall get the validity of P.G.extended to cover such extended time for completion of work plus 60days. (d)The value of PG to be submitted by the Contractor is based onoriginal contract value and shall not change due to subsequentvariation(s) in the original contract value. (e)The PerformanceGuarantee (PG) shall be released after physical completion of the workbased on 'Completion Certificate' issued by the competent authoritystating that the Contractor has completed the work in all respectssatisfactorily. (f)Whenever the contract is rescinded, the PerformanceGuarantee already submitted for the contract shall be encashed. (g)TheEngineer shall not make a claim under the Performance Guaranteeexcept for amounts to which the President of India is entitled under thecontract (not withstanding and/or without prejudice to any otherprovisions in the contract agreement) in the event of: (i)Failure by theContractor to extend the validity of the Performance Guarantee asdescribed herein above, in which event the Engineer may claim the fullamount of the Performance Guarantee. (ii)Failure by the Contractor topay President of India any amount due, either as agreed by theContractor or determined under any of the Clauses/Conditions of theAgreement, within 30 days of the service of notice to this effect byEngineer. (iii)The Contract being determined or rescinded under clause62 of these conditions
Balance sheet for the 4th previous year (i.e. FY 2022-23 or as applicable for theinstance tender) as per para 10.2 of GCC-2022 shall be considered in evaluation offinancial eligibility criteria only when it is clearly certified in Annex-VI B or a selfdeclared certificate duly signed by chartered accountant and the tenderer that thebalance sheet of last financial year (i.e. FY 2025-26 or as applicable for the instancetender) has not been audited/yet to be prepared. Annexure has been attached forsuch certificate format
All Rules of NIT & Post LOA shall be governed by GCC & tenderer agree to adhere toit without any dispute
General Conditions of Contract-2022 has been added in tender document. Please gothrough this General Condition of Contract-2022 along with advanced correctionslips before bidding. In case of any discrepancy, contradiction with regard to GCC(except special condition of contract) in that case GCC- 2022 will be applicable
Infringement removal/Utility shifting of Signalling & Telecom cables and equipment's in connection with Double line work in CAR-CPU section in Prayagraj division of North Central Railway.
SIG-WS-CONTRACT-584~NCR
SIG-WS-CONTRACT-584
Open
Works - General
12 Months
Prayagraj, Uttar Pradesh
₹0
₹5.6 L
19 Aug 2026
19 Aug 2026
31 Aug 2026
136 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | Above/ Below/Par | ||
| — | — | — | 2,79,34,116.38 | ||
| — | 30.00 | — | — | ||
| Q-Series Line Relay (QNA1 Type),AC immunized, 8F/8B, 24 V DC along with plug board (base plate), connectors, retaining clips etc and conforming to BRS-931A and RDSO Specn.No.IRS:S34, S-23 , S-60 or latest, as applicable. The interlocking code for this unit shall be "ABDGH". Inspection by RDSO. | — | — | — | 1,33,177.2 | |
| — | 30.00 | — | — | ||
| Q-Series Track Relay (QTA2 Type), AC immunized, 9 Ohms, 2F/1B along with plug board (base plate), connectors, retaining clips etc and conforming to BRS:939A & 966(Appendix F2) or latest and RDSO Specn.No.IRS:S@45"44@ S-23 , S-60 or latest, as applicable.The interlocking code for this unit shall be "FGHKX". Inspection by RDSO. | — | — | — | 1,14,097.5 | |
| — | 20.00 | — | — | ||
| Q-Series Twin Neutral Line Relay(QNNA1 Type), AC immunised, 6F/2B, 24V DC complete with plug board(base plate), connectors and retaining clips etc and conforming to BRS-960 and RDSO Specn.No.IRS:S@45"44@ S-23, S-60 or latest as applicable. The interlocking code for this unit shall be "CDEHX".Inspection by RDSO | — | — | — | 92,785.8 | |
| — | 20.00 | — | — | ||
| Charging of Lead Acid Batteries, 2V, 80 AH, with contractors own battery grade sulphuric acid and distilled water with minimum two charge - discharge cycles, installation of charged batteries in groups & their connection & wiring. The work shall be done as per the procedure prescribed by the OEM and extant practice of N.C.Rly and instruction of Engineer-in-charge. Detailed measurements of initial charging shall be recorded jointly by contractor & Rly's site-in-charge. | — | — | — | 5,078.4 | |
| — | 20.00 | — | — | ||
| Installation of DC track circuits (Straight Portion) including supply of materials as per directive of site Engineer. NOTE : (i) This includes drilling 9/32" holes on rails, provision of double continuity GI wire bonding, provision of Block Joints 60 Kg/52 Kg/90R with machined fish plates, installation of Track lead junction box (separately for (+) and (-) rails), provision of track lead jumper wires/cables, fixing of track circuit equipment i.e. track charger, resistance, fuses, batteries, chokes, relays, anti-titling arranginment and painting, lettering and numbering of DC track circuit equipments etc., (ii) [a] Un-machined fish plates shall be supplied by the Railway's, but machining of fish plates shall be done by the Tenderer. In case of provision of Glued Joints by Engineering Department in lieu of RDSO Block joint, the cost of machining of fish plates@ 100/- per straight track circuit and @ 500/- per point zone track circuit will be deducted. [b] This includes insulation of gauge tie plates, Crossing plates, rod in siding points if required or any other place as instructed by Railway Site Engineer, by Tenderer's insulation materials. Railway will supply Track Charger, B-type choke, Resistance, Un-charged battery, TLJB and relays through a separate schedule/from the stores of railway consignee. These are to be transported to site of work at contractor's cost. Tenderer/Contractor shall supply any other materials that are required for the work | — | — | — | 1,57,987.6 | |
| — | 20.00 | — | — | ||
| Installation of DC track circuits (Point zone) including supply of materials as per directive of site Engineer. NOTE : (i) This includes drilling 9/32" holes on rails, provision of double continuity GI wire bonding, provision of Block Joints 60 Kg/52 Kg/90R with machined fish plates, installation of Track lead junction box (separately for (+) and (-) rails), provision of track lead jumper wires/cables, fixing of track circuit equipment i.e. track charger, resistance, fuses, batteries, chokes, relays, anti-titling arranginment and painting, lettering and numbering of DC track circuit equipments etc., (ii) [a] Un-machined fish plates shall be supplied by the Railway's, but machining of fish plates shall be done by the Tenderer. In case of provision of Glued Joints by Engineering Department in lieu of RDSO Block joint, the cost of machining of fish plates@ 100/- per straight track circuit and @ 500/- per point zone track circuit will be deducted. [b] This includes insulation of gauge tie plates, Crossing plates, rod in siding points if required or any other place as instructed by Railway Site Engineer, by Tenderer's insulation materials. Railway will supply Track Charger, B-type choke, Resistance, Un-charged battery, TLJB and relays through a separate schedule/from the stores of railway consignee. These are to be transported to site of work at contractor's cost. Tenderer/Contractor shall supply any other materials that are required for the work. | — | — | — | 2,55,288.8 | |
| — | 10.00 | — | — | ||
| Supply of Calling ON Signal Unit, non metallic, with Brackets, clamps and fixing accessories, suitable to LED signal lighting unit and as per RDSO spec. RDSO/SPN/194/2006 (Rev. 2.0) or latest. The FRP material shall conform to RDSO/SPN/151/1997 or latest. Calling On Signal Unit shall conform to RDSO Drg no SA- 24351(Adv) Alt1 or latest without lamp, lamp holder and lens. Inspection by consignee. | — | — | — | 1,16,620.6 | |
| — | 50.00 | — | — | ||
| Supply of hand cuff lock of Godrej/Navtal or reputed make with key and as approved by site engineer. Inspection by consignee. | — | — | — | 22,688 | |
| — | 20.00 | — | — | ||
| Casting, concreting and curing of foundation for Main Signal Post in the ratio of 1:3:6 as per NCR drg.No. TYP/013/14/SIG Found dt.12.11.14 or latest, using standard size of foundation/galvanized anchor bolts complete, required for erection of colour light signal post. Anchor bolts complete should comply with the RDSO drg. no. SA 116 A/M. Item includes excavation, ramming of CC using vibrator, curing and plastering with 1:4 cement-sand mixture (aggregate will not exceed 3.8 cm). Aggregate, cement, sand and holding down bolts will be supplied by contractor. Any machines & tools, if required for execution of this item, will be arranged/provided by contractor | — | — | — | 2,70,125.6 | |
| — | 10.00 | — | — | ||
| Casting, concreting and curing of foundation for Position Light Shunt Signal as per Drg.No.SIG/10/86/C dt.19.02.86 or latest using standard size of foundation/galvanized anchor bolts complete, required for erection of shunt signal post. Anchor bolts complete should comply with the RDSO drg. no. SA 116 A/M. Item includes excavation, ramming of CC using vibrator, curing and plastering with 1:4 cement sand mixture. Aggregate cement, sand and holding down bolts, will be supplied by contractor. Any machines and tools, if required for execution of this item, will be arranged/provided by contractor. | — | — | — | 36,686.6 | |
| — | 20.00 | — | — | ||
| Erection of CLS Post with base and signal unit on top or on Offset Bracket including erection of auxiliary signals like calling on, shunt signal if any. It includes fixing of all LEDs and wiring of complete signal including route and auxilliary signals, if any. It includes fixing of front and back staging, ladder and guards, signal name plates / boards, with contractor's own brackets and fixing materials. The work shall be done as per instructions of Rly engineer at site. It also includes provision & fixing of maintenance platform as per design given by Engineer -In-Charge at site. The Item includes cutting of Signal post if required by Site In charge. | — | — | — | 1,17,574.8 | |
| — | 10.00 | — | — | ||
| Erection of Position Light Shunt signal with Base, Post, Signal unit, complete fixing of LEDs and wiring of full signal. It includes fixing of Number Plates. The work shall be done as per instructions of Rly engineer at site. | — | — | — | 9,510.5 | |
| — | 2.00 | — | — | ||
| Fixing of Junction type Route Indicator on top of signal post and complete wiring, 1-Way/2-Way/3- Way/4- Way/5-Way/6-Way/theater type. | — | — | — | 2,224 | |
| — | 2.00 | — | — | ||
| Supply of Electrically Operated Lifting Barrier complete set suitable for 110VDC/110VAC / 24V DC supply, without hand generator back up, and motorized boom locking arrangements as per RDSO Spec. SPN/208/2012 Ver. 2.0 or latest. The 02 Nos of Barriers of length 09.76 Mtrs. should be supplied along with stop boards and light. The spares & tool kit mentioned in RDSO Spec. no. RDSO/SPN/208/2012 Ver. 2.0 and Amndt. 1 or latest,clause 10.1 & 10.2 reproduced as below should be supplied along with each full set :-i) GI boom - 1 no. complete.ii) Belt - 1 no.iii) Crank handle - 1 no.iv) Motor Contactor - 1 no.v) Motor protection MCB- 1 no.vi) Push button complete- 2 nos.vii) Limit switch - 3 nos. (1 lever type and 2 top roller type)viii) Fuses used - 2 setsTool kit consisting of standard sizes of wrinch/ spanner and Allen keys should also be supplied with each set (02 nos.) of Electric Lifting barrier.Inspection by RDSO. | — | — | — | 7,58,319.5 | |
| — | 8.00 | — | — | ||
| Installation, testing and commissioning of electrically operated lifting barrier, complete with casting of cement concrete foundation for pedestal and boom rest post, cabling, power supply connection, earthing of barriers & wiring with complete outdoor work as per approved drawing, wiring etc. | — | — | — | 4,45,306.08 | |
| — | 2.00 | — | — | ||
| Supply, Installation,testing and commissioning of Sliding type mechanical Boom barrier (SBB) assembly, 11 to 12 Meter Long, movement drive mechanism, resetting & supporting stand suitable for Mechanical/Electrical level crossing gate as an emergency arrangements as per GZB Workshop drawing no. SA- SWG/GZB/E/01. The sliding boom assembly should be have the provision of 50mmx50mmx50mm angles for the entire length. Boom rest posts should be 10 no per gate or more as per site requirement. Painting should be completely done of all the assemblies/parts of Sliding LC gate..Inspection By Consignee | — | — | — | 3,44,128.6 | |
| — | 4.00 | — | — | ||
| Supply, installation, testing and commissioning of LED type control cum indication panel complete with pre wired Tag- Blocks, Wires MS angles etc. for LC gate , depicting the yard layout Signal, Point, Track circuit, Operating / emergency Push Button, counter with sealing arrangements, house in a Steel metal cabinet. Th is shall be consist 15 x 10 exchangeable Domino. Unit as per Spec. SPN/186/2004 Rev. 2.0 or latest. Th e indoor wiring inside panel shall be terminated on tag block as per instructions of Engineer-in-charge. Th e wiring on panel tag blocks shall be repeated on tag blocks located in relay room. Th is includes laying & termination of cable, if any from Panel Room to Relay Room in HDPE pipe..Inspection By Consignee | — | — | — | 2,56,285.2 | |
| — | 500.00 | — | — | ||
| Supply of Cartridge Fuse block, made of PBT, as per RDSO spec. No. IRS: S-75/2006 (Rev.2) or latest and as per Drawing. No. SA- 23748 (Alt.-4) or latest Inspection by RDSO. | — | — | — | 1,21,775 | |
| — | 5000.00 | — | — | ||
| Supply of ARA terminal block, made of PBT, as per RDSO spec. No. IRS: S-75/2006 (Rev.2) or latest and as per Drawing. No. SA- 23741A (Alt.-4) or latest. Inspection by RDSO. | — | — | — | 5,85,050 | |
| — | 125.00 | — | — | ||
| Excavation, casting, curing of foundation and Installation and Erection of Apparatus case Full as per Drg No. AGC/FULL LOC/2023/01 Dtd:14.08.25 or latest (App. Case as per RDSO drg. no. RDSO/S-11500 or latest) with contractor's own frame, cement and other material in the ratio 1:3:6. 'E' type lock to be supplied and installed with App. case.This includes filling of location foundations with river bed sand and plastering on top with a mixture of 1:4 of cement and sand. | — | — | — | 15,34,027.5 | |
| — | 20.00 | — | — | ||
| Excavation, casting, curing of foundation and Installation and Erection of Apparatus case Half (App. Case as per RDSO drg. no. AGC/HALF LOC/2023/01 Dtd:14.08.25 or latest)with contractor's own frame, cement and other material in the ratio 1:3:6.'E' type lock to be supplied and installed with App. case.This includes filling of location foundations with river bed sand and plastering on top with a mixture of 1:4 of cement and sand. | — | — | — | 2,06,483.6 | |
| — | 5000.00 | — | — | ||
| Fixing of ARA(M-6) Terminals /Screw less connectors / modular disconnect terminal blocks and fuse blocks on phenolic laminated sheets and fixing by stainless steel/brass nuts & bolts. This includes provision of two additional holes on the board on either side for cable conductor entry. The work shall be carried out a per instructions of railway Engineer incharge.(Supply of all above terminals has been covered separately). | — | — | — | 88,100 | |
| — | 2500.00 | — | — | ||
| Supply of Disconnect Terminal block for four conductors with screwing cage/clamp type, sliding switch disconnect, as per RDSO spec. RDSO/SPN/189/2004 Ver. 3.0 or latest, for each conductor size up to 2.5 sq. mm, equivalent of M6 terminals. Each terminal block equipped with two markers, on top and bottom, an end plate, two end clamps and adequate lenght of rails for fitting terminal blocks. Inspection by RDSO. | — | — | — | 4,81,800 | |
| — | 8500.00 | — | — | ||
| Termination of Outdoor Cables (Main Cables /tail cables) at ARA/Disconnect type terminals provided in Apparatus Cases, Cable termination rack in relay room, station building, generator room etc. The item includes dressing of cables and wires with dressing threads as per standard practice. All material required for this item will be supplied by contractor. The outdoor cable shall be terminated in Relay Room, DG Room, ASM Room etc under supervision and instructions issued by Engr. incharge of the work. | — | — | — | 1,25,460 | |
| — | 125.00 | — | — | ||
| Fabrication and fixing of phenolic laminated sheet of grade P3, minimum 10 mm thick,as per Apparatus case diagram/plan, in location box by providing all fixtures like ARA/Disconnect terminals, fuse blocks, fuses, relays on square bars etc. including fixing of PVC coated string rods at the back side for cable support with contractor's own material like iron angle, nuts, bolts etc. The iron angle for fixing shall be minimum 3 mm thick. This also includes fixing of teak wood shelf minimum 25 mm thick for holding track circuit equipments. The work shall be done as per instructions of Rly engineer at site. Inspection by Rites. (Apparatus case Full) | — | — | — | 5,59,555 | |
| — | 20.00 | — | — | ||
| Fabrication and fixing of phenolic laminated sheet of grade P3, minimum 10 mm thick,as per Apparatus case diagram/plan, in location box by providing all fixtures like ARA/Disconnect terminals, fuse blocks, fuses, relays on square bars etc. including fixing of PVC coated string rods at the back side for cable support with contractor's own material like iron angle, nuts, bolts etc. The iron angle for fixing shall be minimum 3 mm thick. This also includes fixing of teak wood shelf minimum 25 mm thick for holding track circuit equipments. The work shall be done as per instructions of Rly engineer at site. (Apparatus case Half). Inspection- Consignee | — | — | — | 48,563.6 | |
| — | 100.00 | — | — | ||
| Shifting of existing full location boxes coming in the alignment of new line. The work includes losing & removal of soil around location boxes by excavating soil around foundation, making of pit for shifting of location box horizontally opposite to railway track up to 0.5 to 1.0mtr. This includes loosing of existing cable coils without any damage. The excavated soil shall be back filled after shifting of Location Boxes Location box shall be shifted by push method with the help of jacks or by crane by contractors own expenditure under instructions of engineer in-charge at site. The work may affect train working hence the work shall be done as per margin only or during traffic block only. | — | — | — | 4,36,993 | |
| — | 100.00 | — | — | ||
| Shifting of existing half location boxes comingin the alignment of new line. The work includes losing & removal of soil around location boxes by excavating soil around foundation, making of pit for shifting of location box horizontally opposite to railway This includes loosing of existing cable coils without any damage. The excavated soil shall be back filled after shifting of Location Boxes. Location box shall be shifted by push method with the help of jacks or by crane by contractors own expenditure under instructions of engineer in-charge at site. The work may affect train working hence the work shall be done as per margin only or during traffic block | — | — | — | 3,37,972 | |
| — | 5000.00 | — | — | ||
| Horizontal Boring/Manual moling without damage to surface road /track forlaying/isertion of DWC/GI/HDPE pipe. Thebore shall be done at the depth ofminimum 1400 mm from the groundlevel. The ground level shall beconsidered ignoring the bank height ofthe bank of the road. Note:-DWC/HDPE/GI Pipe Supply is not coveredunder this item. Contactor shall provideall material required for work andadequate nos. of labours for proper layingof cables into the bore. Cable shall be laidcautiously so that it should not get damage due to rough handling &pressure on cable. Payment of boringshall be made only after DWC/HDPE/GIpipe is laid in the bore. | — | — | — | 51,45,200 | |
| — | 2500.00 | — | — | ||
| Horizontal direction drilling(HDD)/Trenchless digging/machine drilling without damage to surface road/track for laying/insertion of HDPE/GI/DWC pipe.The bore shall be done at the depth of minimum 1400mm from the ground level.The ground level shall be considered ignoring the bank height of the bank of the road.Note:-DWC/HDPE/GIPipeSupply is not covered under this item.Contactor shall provide all material required for work and adequate nos.oflabours for proper laying of cables into the bore.Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable. | — | — | — | 16,05,275 | |
| — | 50000.00 | — | — | ||
| Laying of S&T Cables of various cores/ pairs/ quads in trenches/ GI pipes/ RCC pipes/ DWC pipes etc. as per the site requirement and as per approved cable route plan. This also includes laying of cables in track crossings & road crossings.(Cables will be meggered before and after its laying by contractor under supervision of Railway Representative and he will submit the meggering report of each testing). Length of the cable laid includes the length of the cable coiled for termination purposes. | — | — | — | 3,42,000 | |
| — | 100.00 | — | — | ||
| Supply of Medium class GI pipes 100 mm dia (4.5 mm thickness) with thread collars as per IS 1239 (Part 1) 2004 or latest with coupling on culverts/bridges, perforated at a distance of 20 cm or less with 10 mm dia hole, or at any other locations as decided by Site Engineer. It includes supply of all material required for fixing arrangement. Contractor will also supply flexible/corrugated HDPE pipe at the end of GI pipe to protect the cables from sharp edges and sudden bends. Inspection by consignee. | — | — | — | 99,131 | |
| — | 8500.00 | — | — | ||
| Excavation of cable trench as per cable route plan, 1.2Mtr. deep and of 0.3Mtr. to 0.6Mtr. wideat b o t t o m as per RDSO sketch No. SDO/CABLELAYING/003, issued vide RDSO document no. RDSO/SI/G/2010Version1.1 dated04.02.2014 or latest, along side the track in normal soil/strata (including soft rock), conforming to distances as per cable route plan and refilling and ramming of loose soil. This work includes clearing of route from bushes etc, covering of cable laid in trench by loose soil for a layer of 50 mm thickness approximately. The work shall be done as per the extant practice on North Central Railway and instructions of Railway Engineer at site. Incase 1.2m depth of trench is not achievable due to site conditions, specific approval of JAG/SG Officer will be required for each site where trench depth of 1.2 m is not possible, only after approval of JAG/SG Officer proportionate payment can be done. | — | — | — | 5,49,865 | |
| — | 5000.00 | — | — | ||
| Excavation of cable trench as per cable route plan, 1.2 Mtr. deep and of 0.3 Mtr. to 0.6 Mtr. wide at bottom as per RDSO sketch No. SDO/CABLE LAYING/003, issued vide RDSO document No. RDSO/SI/G/2010 Version 1.1 dated 04.02.2014 or latest, alongside the track in rocky soil, conforming to distances as per cable route plan and refilling and ramming of loose soil. This work includes clearing of route from bushes etc,covering of cable laid in trench by loose soil for a layer of 50 mm thickness approximately before covering by bricks. The work shall be done as per the extant practice on North Central Railway and instructions of Railway Engineer at site. In case the full depth of trench is not available, there shall be no proportionate payment and after the approval of minimum JAG Officer, the concreting shall be done as per the RDSO Drg. No.SDO/Cable laying/008, issued vide RDSO document No. RDSO/SI/G/2010 version 1.1 dated 04.02.2014 or latest. | — | — | — | 4,45,550 | |
| — | 2000.00 | — | — | ||
| Cutting of all types of platforms/road crossing and trenching and excavation to a width and depth of 300 mm x 300 mm, laying of DWC/HDPE/GI pipe in the trench and refilling and concreting it afterwards as per original condition. In hard rocky ground area , cables will be laid normally on layer of soft earth of 0.05 mtrs thickness previously deposited at bottom of the trench . The cutting to be filled and finished with cement/concrete, as per the RDSO drawing no.SDO/Cable laying/008, issued vide RDSO document no. RDSO/SI/G/2010 Version 1.1 dated 04.02.2014 or latest. | — | — | — | 3,17,620 | |
| — | 2000.00 | — | — | ||
| Cross trench for identification of the route of existing signlalling and telecomm cables. | — | — | — | 5,80,580 | |
| — | 500.00 | — | — | ||
| Placing ofDWC/RCC pipes along with collars in trenches at places of roadcrossings,platform cuttings etc.also for straight cable laying(Cable laying is covered separately) | — | — | — | 16,610 | |
| — | — | — | track | ||
| — | — | — | and | ||
| — | 65.00 | — | — | ||
| Supply and installation of earth electrode as per standard practice and as per NCR Drawing No. S&T/CONST/6.4/97. It includes supply of GI pipe of 3 meter length. It includes connecting the earth electrode to the equipments which are required to be earthed including digging of earth pit 3 meter deep and fi xing earth electrode pipe, casting of cement concrete enclosure with cover (cover as per drawing No. S&T/CONST/6.3/97. It includes installation of 7 strand GI wires as earth lead wires, supported on MS fl at size 5mm x 40 mm, soldering and nut bolt both, one end of both earth lead wire and MS fl at to earth electrode and other end to Location boxes, block equipments, power equipments, cable sheath, signals etc. as per site requirement and as per instructions given by engineer incharge.Inspection by Consignee. | — | — | — | 2,17,980.1 | |
| — | 15.00 | — | — | ||
| Supply of basic material to construct unit maintenance free earth as per RDSO Specs. No RDSO/SPN/197 Ver. 1.0 or latest to achieve a resistance less than 1 ohm. It consist of following: (a) Copper bonded steel electrode of minimum 3.0 m long, minimum 17.0 mm dia with copper bonding thickness of minimum 250 microns and UL listed and marked = 1 no. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. (c) Copper strip of 150x25x6 mm, to terminate earth rod = 1 no. (d) Copper strip of 300x25x6 mm (MEEB) = 1 no. (e) Copper strip of 150x25x6mm (SEEB) = 1 no. (ii) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate.(minimum 10 meter) (iii) Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter ) (iv) Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting various equipments to SEEB (v) Supply of copper lug sleeve for 3/16 cable Inspection by Consignee. | — | — | — | 2,70,637.8 | |
| — | 15.00 | — | — | ||
| Installation of Unit Maintenance Free Earth to achieve a resistance less than 1 ohm as supplied under item no. 13002 of Chapter 13 of SOR. It includes (i) Digging the earth to the required depth. (ii) Insertion of electrode. (iii) Filling of earth enhancing compound (Approx.30 Kg) (iv) Provision of exothermic weld connections to copper tape of 25 mm x 6 mm x 150 mm to the earth electrodes. All material tools and features required for weld will be arranged by contractor. (v) This also includes CC cover 1.5 ft x 1.5 ft. 1 ft wall thickness 2 inch with cover 3 inch thickness. Cables 35 Sq mm/ 16 Sq mm/10 sq mm for connecting earth to busbar, busbar to busbar and busbars to various equipments. Earth electrode of 17.20 mm dia and 3.00 meter long high tensile low carbon steel circular rods molecularly bonded with copper and outer surface (minimum copper bonding thickness of 250 micrones to made requirement of under writer's laboratories (UL) 467- 2007 or latest. Copper strips of 150 mm x 25 mm x 6 mm to be welded with each earth electrode, copper strips of 300 mm x 25 mm x 6 mm for main equip- potential busbar, copper strips of 150 mm x 25 mm x 6 mm sub equip-potential busbar in relay room, power room and panel room. GI strip 25 mm x 2 mm for ring formation of earth pits Earth enhancement material in bags for each Earth Electrode. Inspection chamber of site 300 mm x 300 mm x 300 mm (Inside dimension) of approximate 50 mm thick with pulling hooks to cover the earth pits. Note: The installation of this item shall be carried out by the contractor as per RDSO Specn.No.RDSO/SPN/ 197 Ver 1.0 or latest. Typical RDSO approved drawings referred in the RDSO specification document are : (i) SDO/RDSO/E&B/001 for typical installation of Earth, (ii) SDO/RDSO/E&B/002 for typical bondong and earthing connections, (iii) SDO/RDSO/E&B/003 for typical arrangement for earth resistance measurements. | — | — | — | 1,07,897.55 | |
| — | 850.00 | — | — | ||
| Cement concrete work for miscellaneous, unscheduled items in ratio 1:3:6 of cement, coarse, sand and aggregate Item includes excavation, ramming of CC by using vibrator, curing and plastering with cement and sand mixture in ratio 1:4 (aggregate will not exceed beyond 3.8 cm). The aggregate cement and sand will be supplied by contractor. | — | — | — | 42,20,573 | |
| — | 2200.00 | — | — | ||
| Lettering and Numbering of all S&T gears like Signals, Loc. Boxes, Pt. Machines, TLJBs, Block joints etc. Each item to be taken as one unit. | — | — | — | 1,83,942 | |
| — | 125.00 | — | — | ||
| Painting of two coats of Enamel paint over one coat of Red Oxide primer after scrapping and cleaning of the surface. Paint to be of reputed make Asian/Dulux/Berger or similar.App. Cases inside and outside to be done by Silver colour. (Apparatus Case Full) | — | — | — | 84,156.25 | |
| — | 20.00 | — | — | ||
| Painting of two coats of Enamel paint over one coat of Red Oxide primer after scrapping and cleaning of the surface. Paint to be of reputed make Asian/Dulux/Berger or similar.App. Cases inside and outside to be done by Silver colour. (Apparatus Case Half) | — | — | — | 12,634.6 | |
| — | 20.00 | — | — | ||
| Painting of two coats of Enamel paint over one coat of Red Oxide primer after scrapping and cleaning of the surface. Paint to be of reputed make Asian/Dulux/Berger or similar. (Main Signal post, base, unit and complete fittings) | — | — | — | 18,630 | |
| — | 5.00 | — | — | ||
| " Painting of two coats of Enamel paint over one coat of Red Oxide primer after scrapping and cleaning of the surface. Paint to be of reputed make Asian/Dulux/Berger or similar. (Shunt Signal post, base, unit and complete fittings) " | — | — | — | 1,986.05 | |
| — | 10.00 | — | — | ||
| Dismantling and Releasing of existing Electrically operated LC gate/Mechanically operated LC gate and other associated S&T fittings. All the released material will be transported to the SSE/Consignee depot. | — | — | — | 89,463.1 | |
| — | 100.00 | — | — | ||
| Dismantling and Releasing of existing Location boxes/Apparatus cases/Jn boxes and other associated S&T fi ttings. All the released material will be transported to the SSE/Consignee depot. | — | — | — | 91,744 | |
| — | 100.00 | — | — | ||
| Hiring of JCB/Hydra/Poclain machine (in good working condition)for levelling & dressing of ground/dismantling structures including disposal of debris through dumpers/Shifting the location box or signal post with foundation etc. with contractors labour, JCB/Hydra/Poclain machine, machine operator, fueletc. Payment shall be made for actual working hrs. at site & proportionate payment to be made in case less than hours. Note: Vehicle shall not be more than 3 years old. | — | — | — | 90,000 | |
| — | 1000.00 | — | — | ||
| Shifting of existing working functions like signals/Shunt/Callingon/Points/Track circuit setc. from old cable to new laid cables carefully without affecting the traffic under disconnection/blocks, This work also includes releasing the existing tail cables from the relevant gears and resurfacing the earth excavated as instructed by Railway representative at site.(1 number=1 cable) | — | — | — | 21,23,000 | |
| — | 50.00 | — | — | ||
| Supply of VF Transformers, rack mounting type/Cylindrical, 1120:470 Ohms as per RDSO Speen.No. IRS: TC-22/76 or latest.Inspection by Consignee | — | — | — | 62,004.5 | |
| — | 30.00 | — | — | ||
| "Supply of 24 fiber optical fiber cable straight joint enclosure (SJC) complete with all accessories along with enclosures with heat shrinkable splice protection sleeve as per RDSO spec. RDSO/SPN/TC68/2014Revision 1.0, Amndt. 1.0 or latest. Splice losses in no case should be more than 0.1 dB. Inspection by Consignee." | — | — | — | 1,65,163.5 | |
| — | 50.00 | — | — | ||
| Supply of thermo shrink jointing kit as per RDSO Specn.No. IRS: TC 77-2012 (Rev.3.0) with (Amdt.- 1 to 3) or latest, suitable for 6 Quad/jelly filled cables for straight through/derivation joints. It includes supply of all the accessories, without transformer.Inspection by RDSO. | — | — | — | 1,68,057.5 | |
| — | 50.00 | — | — | ||
| "Installation of thermo shrink jointing kit as per RDSO Specn.No. IRS: TC 77-2012 (Rev.3.0) with(Amdt.-1 to 3) or latest, suitable for 6 Quad/jelly filled cables for straight through/derivation joints. It includes supply of all the accessories, without transformer." | — | — | — | 85,669 | |
| — | 5.00 | — | — | ||
| Blowing/drawing of OFC cable in the HDPE pipe duct and protective work already provided in the trench. The cable shall be laid only after the successful completion of the DIT (Duct Integrity test). The DIT should be certified by the Railway engineer at site. All the equipments/machinery required shall be arranged by the contractor. | — | — | — | 85,527.05 | |
| — | 5.00 | — | — | ||
| "Laying of HDPE duct as per the approved cable route plan in the exavated trenches/other protected works/RCC channel etc. including all accessories like end caps, collars, bends, couplers etc. The ends of the duct to be sealed with end plugs till OFC blowing is done. Important: The laying of OFC cable independently or along with Quad cable/PIJF cable in the same trench shall be governed by the RDSO drawings no. RDSO/TCDO/COP-6(a) and RDSO/TCDO/COP-8(a)respectively, issued vide Chapter-XIII of the Telecomm Manual." | — | — | — | 39,328.2 | |
| — | 30.00 | — | — | ||
| Splicing of 24 core optic fibre cable and making the splicing joint with contractor's own machine and tools. Joint should be prepared in such a way that the top of the enclosure shopuld be at a depth of minimum 1.2 mtr and the enclosure should be covered with soft soil and bricks. Splice loss of each fibre should be less than 0.05 dB. | — | — | — | 3,60,270.3 | |
| — | 30.00 | — | — | ||
| Construction of OFC jointing pit of size 1mx1mx0.6m, using bricks, sand and cement in the ratio 1:3. The thickness of the wall shall be 120 mm. The top cover shall be of concrete of thickness 75 mm with two iron handles on top of it. The pit shall be covered with sand after putting the joint enclosure. All construction material to be supplied by contractor. | — | — | — | 1,87,686.6 | |
| — | 12000.00 | — | — | ||
| Loading, Transportation/Carriage and Unloading of various S&T material by a 9 MT truck, from/to the consignee depot to/from various locations, as decided by the Railways. | — | — | — | 6,22,800 | |
| — | 50000.00 | — | — | ||
| Provision & running of MUVs to the sites of work as per requirement and direction of Engineer In charge along with Driver for Transportation of less heavy materials & manpower. The rates includes all taxes, license fee, road permit, driver wages, fuel, repair and maintenance cost etc complete in all respects. | — | — | — | 9,74,500 | |
| — | 250.00 | — | — | ||
| "Provision of bonding with GI wire/cable pieces for track jumper & fish plate joints bonds. This will include drilling of 7.1mm dia holes in rails (4 Nos) and provision of two jumpers for each bond, etc. with contractors own materials and tools as per instruction of Rly engineer at site including supply of GI wire/insulated jacketed wire & channel Pins single groove, galvanized, 7 mm suitable for 4mm dia bonding wire as per spec No IRS S 17 & 69/M with latest amendment.However cable pieces will be provided by Railways, if required." | — | — | — | 27,700 | |
| — | 240.00 | — | — | ||
| "Laying and fixing of Medium class GI pipes 100 mm dia (4.5 mm thickness) as per IS 1239 ( Part 1) 2004 or latest with coupling on culverts/bridges, perforated at a distance of 20 cm or less with 10 mm dia hole, or at any other locations as decided by Site Engineer.The GI pipe is to be filled with chattered compound. It includes supply of all material required for fixing arrangement. Contractor will also supply flexible/corrugated HDPE pipe at the end of GI pipe to protect the cables from sharp edges and sudden bends. The laying and fixing to be done as per RDSO drawings no. SDO/cable laying/011 and SDO/cable laying/012, issued vide RDSO document no.RDSO/SI/G/2010 Version 1.1 dated04.02.2014, or latest" | — | — | — | 80,354.4 | |
| — | 40.00 | — | — | ||
| Cable insertion in old locations/Station Relay room/Cable pit etc as per site engineer and filling with sand and plastering the same. Note; All the sundry materials except that to be supplied by railways will be supplied by the contractor. | — | — | — | 1,12,784 | |
| — | 20.00 | — | — | ||
| Supply and installation of FMS(24 F-in & out ) rackmountable single mode withSuitable type connector(SCType or as per siterequirement) with splicingand termination of OFC cableswith all accessories (Pig tailand other materials requiredfor work to be supplied bycontractor ) Make D-link,Raycom, Tyco or similar. (Inspection Agency:-Consignee). | — | — | — | 1,37,833 | |
| — | 1.00 | — | — | ||
| Supply of Multifunction Wideformat Printer and Plotter . Make/model- HP Designjet T2600 36 -in A0-A4 post script Multifunction printer with 1year waranty or similar | — | — | — | 4,92,600 | |
| — | 5.00 | — | — | ||
| Supply,installation of 19"12U rack with transparent glass door with accessories like fans & tray etc.Inspection by Consignee. | — | — | — | 53,698.4 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
ACS01to11ofGCC2022.pdf
ATTACHMENT
GCCACS-123389822Dated12.08.2026_compressed.pdf
ATTACHMENT
GCC_April-2022_2022_CE-I_CT_GCC-2022_POLICY_27_04_22.pdf
ATTACHMENT
TypicalDiagramforLocationBoxFoundationdrawing_1584.pdf
ATTACHMENT
TechnicalCircular-1-24forDifferentBoardsusedinSingnalling1584.pdf
ATTACHMENT
signalfoundationdrg2584.pdf
ATTACHMENT
FinalMasterTenderDocumentv1.2.pdf
ATTACHMENT
JPO 05
ATTACHMENT
AnnexureAcl584.pdf
ATTACHMENT
BankGuaranteeforBidsecurityformatAnnVIA584.pdf
ATTACHMENT
Annex-VIB584.pdf
ATTACHMENT
LASTFYDECLARATION1584.pdf
ATTACHMENT
JPO-05-2023UndertakingtheworkoflayingundergroundSignallingTelecomcablesandEngineering1584_1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].