Construction of Stadium, Guest House, Girls Hostel and Health Centre at National Law University, Cuttack in Odisha

Sl. No. Description of Item Schedule Amount Total Amount

Sl. No. Description of Item Schedule Amount Non-Schedule Amount Total Amount

Sl. No. Description of Item Schedule Amount Non-Schedule Amount Total Amount

5 Firefighting Works 571413.25 574395.75 1145809.00

Digitally signed by ANUJ

BILL OF QUANTITY FOR STADIUM MAIN BUILDING, BADMINTON COURT, GYMNASIUM & TOILET BLOCK FOR NATIONAL LAW UNIVERSITY, AT CUTTACK

SCHEDULE SCHEDULE NON SCHEDULE

S.NO. DSR ITEM DESCRIPTION UNIT QTY SCHEDULE

RATE AMOUNT AMOUNT

2 1.00 PILE WORK

Boring, providing and installation bored cast-in-situ reinforced

cement concrete piles of grade M-25 of specified diameter and

length below the pile cap, to carry a safe working load not less than

specified, excluding the cost of steel reinforcement but including

the cost of boring with bentonite solution and temporary casing of

appropriate length for setting out and removal of same and the

length of the pile to be embedded in the pile cap etc. by percussion

drilling using Direct mud circulation (DMC) or Bailer and chisel

technique by tripod and mechanical Winch Machine all complete,

including removal of excavated earth with all its lifts and leads

(length of pile for payment shall be measured up to bottom of pile

cap). 500 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV)

including installation of loading platform by Kent ledge method and

preparation of pile head or construction of test cap and dismantling

4 20.6.2.1 of test cap after test etc. complete as per specification & the Per Test 15.00 61173.03 917595.47 0.00

direction of Engineer in-charge. Single pile above 50 tonne and up

to 100 tonne Safe capacity. Initial test (Test Load 2.5 times the

5 2.00 EARTH WORKS

Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in depth,

6 2.6.1 1.5 m in width as well as 10 sqm on plan) including getting out and Cum 1116.80 218.45 243970.53 0.00

disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as

directed by Engineer-in-charge. All kinds of soils

Earth work in excavation by mechanical means (Hydralic

excavator/manual means)over areas (exceeding 30cm in depth.

7 2.7 1.5m in width as well as 10 sqm on plan) including getting out and

disposal of excavated earth, lead upto 50m and lift upto 1.5m, as

directed by Engineer - in Charge

9 2.7.3 Hard rock (blasting prohibited) Cum 52.34 1259.27 65909.99 0.00

Excavating trenches of required width for pipes, cables, etc.

including excavation for sockets, and dressing of sides, ramming of

10 2.10.1.2 bottoms, depth upto 1.5m including getting out the excavated soil, Metre 514.00 443.77 228096.88 0.00

and then returning the soil as required, in layers not exc All kinds of

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in

11 2.25 depth, consolidating each deposited layer by ramming and Cum 867.83 270.03 234335.83 0.00

watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by

mechanical transport upto a lead of 5km also including ramming

watering of the earth in layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete

Supplying and filling in plinth with sand under floors, including

13 2.27 watering, ramming, consolidating and dressing complete. Cum 196.27 2298.00 451029.24 0.00

Surface dressing of the ground including removing vegetation and

14 2.28.1 inequalities not exceeding 15 cm deep and disposal of rubbish, lead Sqm 2063.62 29.93 61770.32 0.00

up to 50 m and lift up to 1.5 m. All kinds of soil

Supplying chemical emulsion in sealed containers including delivery

15 2.34.1 as specified Chlorpyriphos/ Lindane emulsifiable concentrate of Litre 620.50 213.62 132549.33 0.00

Diluting and injecting chemical emulsion for POST-

CONSTRUCTIONAL anti-termite treatment (excluding the cost of

chemical emulsion) : Along external wall where the apron is not

16 2.35.1.1 provided using chemical emulsion @ 7.5 litres / sqm of the vertical Metre 717.42 34.34 24639.50 0.00

surface of the substructure to a depth of 300mm including

excavation channel along the wall & rodding etc. complete: With

Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @

one litre per hole, 300 mm apart including drilling 12 mm diameter

17 2.35.3.1 holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse Sqm 484.59 272.36 131985.01 0.00

sand) to match the existing floor: V

18 4.00 CONCRETE WORKS

Providing and laying in position cement concrete of specified grade

19 4.1 excluding the cost of centering and shuttering - All work up to

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

20 4.1.3 sources : 4 graded stone aggregate 20 mm nominal size Cum 217.30 7831.36 1701765.26 0.00

derived from natural sources)

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural

21 4.1.6 sources : 6 graded stone aggregate 40 mm nominal size derived Cum 119.35 7092.48 846487.11 0.00

from natural sources)

Centering and shuttering including strutting, propping etc. and

removal of form work for :

23 4.3.1 Foundations, footings, bases for columns. Sqm 451.77 327.44 147929.03 0.00

Providing and laying damp-proof course 50mm thick with cement

concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from

24 4.11 natural sources : 4 graded stone aggregate 20mm nominal size Sqm 185.13 480.88 89024.84 0.00

derived from natural sources).

Extra for providing and mixing water proofing material in cement Per 50

25 4.12 concrete work in doses by weight of cement as per manufacturer's kg 67.30 60.77 4089.66 0.00

specification. cement

Providing & applying a coat of residual petroleum bitumen of grade

of VG-10 of approved quality using 1.7kg per square metre on

26 4.13 damp proof course after cleaning the surface with brushes and Sqm 185.13 121.06 22411.23 0.00

finally with a piece of cloth lightly soaked in kerosene oil.

Digitally signed by ANUJ

Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20

mm nominal size) over 75mm thick bed of dry brick ballast 40 mm

27 4.17 nominal size, well rammed and consolidated and grouted with fine Sqm 174.90 724.80 126767.25 0.00

sand, including necessary excavation, levelling & dressing &

finishing the top smooth.

28 5.00 REINFORCED CEMENT CONCRETE WORK

Centering and shuttering including strutting, propping etc. and

removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses,

plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers

35 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 3179.88 855.16 2719303.08 0.00

36 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 303.44 699.39 212221.56 0.00

37 5.9.16 Edges of slabs and breaks in floors and walls

39 5.9.19 Weather shade, Chajjas, corbels etc., including edges. Sqm 145.62 866.54 126185.02 0.00

Steel reinforcement for R.C.C. work including straightening,

40 5.22 cutting, bending, placing in position and binding all complete upto

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening,

42 5.22A cutting, bending, placing in position and binding all complete above

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position ready mixed or site batched design

mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to

accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but

44 5.33.1 excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for the

following grades of concrete. Note: Extra cement up to 10% of the

minimum specified cement content in design mix shall be payable

separately. In case the cement content in design mix is more than

110% of the specified minimum cement content, the contractor

shall have discretion to either re-design the mix or bear the cost of

45 5.33.1 All works upto plinth level.

Concrete of M25 grade with minimum cement content of 330 kg

47 5.33.2 All works above plinth level upto floor V level.

Concrete of M25 grade with minimum cement content of 330 kg

Add for using extra cement in the items of design mix over and

above the specified cement content therein.

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each

four floors or part thereof.

52 6.00 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in foundation and plinth in:

54 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 357.47 7079.72 2530787.51 0.00

Brick work with non modular fly ash bricks conforming to IS:12894,

55 6.34 class designation 10 average compressive strength in super

structure above plinth level up to floor V level in :

56 6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) Cum 687.38 8162.21 5610539.77 0.00

Half brick masonry with non modular fly ash bricks of class

57 6.45 designation 10, conformingio IS :12894, in super structure above

plinth and upto floor V level.

58 6.45.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand) Sqm 1459.80 1031.03 1505095.91 0.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S.

bars at every third course of half brick masonry.

Brick edging 7cm wide 11.4 cm deep to plinth protection with

60 6.44 common burnt clay F.P.S. (non modular) bricks of class designation rmt 427.60 59.33 25370.42 0.00

7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine

61 8.00 MARBLE & GRANITE WORK

Providing and fixing 18mm thick gang saw cut ( premoulded and

prepolished) machine cut for kitchen platforms, vanity counters,

window sills , facias and similar locations of required size of

approved shade, colour and texture laid over 20mm thick base

62 8.2 cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated

with white cement, mixed with matching pigment, epoxy touch ups,

including rubbing, curing, moulding and polishing to edge to give

high gloss finish etc. complete at all levels.

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra

65 8.2.2 Granite of any colour and shade

Extra for providing edge moulding to 18mm thick marble stone

67 8.3.2 counters,Vanities etc. over Item No. 8.2 including machine metre 29.73 444.62 13218.52 0.00

polishing to edge to give high gloss finish etc. complete as per

design approved by Engineer-in-Charge

Extra for fixing marble / granite stone over and above

68 8.4 corresponding basic item, in facia and drops of width upto 150mm metre 29.73 505.23 15020.40 0.00

with epoxy resin baesd adhesive including cleaning etc. complete.

Digitally signed by ANUJ

Extra for providing opening of required size & shape for wash

basins/ kitchen sink in kitchen platform, vanity counters and similar

69 8.5 location in marble/Granite/Stone work including necessary holes for each 39.00 859.31 33512.93 0.00

pillar taps etc. including rubbing and polishing of cut edge etc.

Stone tile (polished) work for wall lining over 12 mm thick bed of

cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry

70 8.9.1.2 @ 3.3 kg/sqm including pointing in white cement complete. Sqm. 42.76 3302.08 141196.86 0.00

8.mm thick Granite of any colour and shade

Providing and fixing Ist quality ceramic glazed wall tiles conforming

to IS: 15622 (thickness to be specified by the manufacturer), of

approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in

71 8.31 skirting, risers of steps and dados, over 12 mm thick bed of cement Sqm 1386.46 1130.77 1567762.36 0.00

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey

cement slurry @ 3.3kg per sqm, including pointing in white cement

mixed with pigment of matching shade complete.

72 9.00 WOOD, WPC & uPVC WORK

Providing and fixing factory made single extruded WPC (Wood

Polymer Composite) solid door/window/Ceosetory windows & other

Frames/Chowkhat comprising of virgin PVC polymer of K value 58-

60 (Suspension Grade), calcium carbonate and natural fibers (wood

powder/ rice husk/wheat husk) and non toxic additives (maximum

toxicity index of 12 for 100 gms) fabricated with miter joints after

applying PVC solvent cement and screwed with full body threaded

star headed SS screws having minimum frame density of 750 kg/

cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),

minimum compressive strength of 58 N/mm2, modulus of elasticity

73 26.86 900 N/mm2 and resistance to spread of flame of Class A category

with property of being termite/borer proof, water/moisture proof

and fire retardant and fixed in position with M.S hold fast/lugs/SS

dash fasteners of required dia and length complete as per direction

of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners

shall be paid for separately).Note: For WPC solid door/window

frames, minus 5mm tolerance in dimensions i.e depth and width of

profile shall be acceptable. Variation in profile dimensions on plus

side shall be acceptable but no extra payment on this account shall

Providing and fixing ISI marked flush door shutters conforming to

IS: 2202 (Part I) decorative type, core of block board construction

75 9.20 with frame of 1st class hard wood and well matched teak 3 ply

veneering with vertical grains or cross bands and face veneers on

both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws.

Providing and fixing factory made single extruded WPC (Wood

Polymer Composite) solid plain flush door shutter of required size

comprising of virgin polymer of K value 58-60 (Suspension Grade),

calcium carbonate and natural fibers (wood powder/ rice

husk/wheat husk) and non toxic additives (maximum toxicity index

of 12 for 100 gms) having minimum density of 650 kg/cum and

screw withdrawal strength of 1800 N (Face) & 900 N (Edge),

minimum compressive strength 50 N/mm2, modulus of elasticity

850 N/mm2 and resistance to spread of flame of Class A category

with property of being termite/ borer proof, water/moisture proof

and fire retardant and fixing with stainless steel butt hinges of

required size with necessary full body threaded star headed counter

sunk S.S screws, all as per direction of Engineer-In- Charge. (Note:

stainless steel butt hinges and necessary S.S screws shall be paid

Extra for providing lipping with 2nd class teak wood battens 25 mm

79 9.23 minimum depth on all edges of flush door shutters (over all area of Sqm 126.72 426.81 54085.19 0.00

door shutter to be measured).

Providing and fixing wooden moulded beading to door and window

80 9.40.1 frames with iron screws, plugs and priming coat on unexposed

surface etc. complete :

Providing and fixing chromium plated brass curtain rod having wall

82 9.46.2 thickness of 1.25mm with two chromium plated brass brackets metre 529.80 399.00 211391.96 0.00

fixed with C.P. brass screws and PVC sleeves etc., wherever

necessary complete :20 mm dia.

Providing and fixing M.S. grills of required pattern in frames of

windows etc. with M.S. flats, square or round bars etc. including

83 9.48.2 priming coat with approved steel primer all complete.Fixed to Kg 1464.04 210.21 307762.30 0.00

openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium extruded section body tubular type

universal hydraulic door closer (having brand logo with ISI, IS :

3564, embossed on the body, door weight upto 36 kg to 80 kg and

84 9.84 door width from 701 mm to 1000 mm), with double speed Each 17.00 910.50 15478.56 0.00

adjustment with necessary accessories

and screws etc. complete.

Providing and fixing ALDSMSS304(250*16mm) aldrop SS304

85 MR-1 250*16mm with screw, with nuts and screws etc. complete : Each 78.00 0.00 973.94 0.00 75967.63

Providing and fixing TS 1010SS 304 SS Sq shape tower bolt dia

86 MR-2 10mm 10" in SS finish in SS304 grade with necessary screws etc. Each 290.00 0.00 431.71 0.00 125196.34

Providing and fixing bright /matt finished Stainless Steel handles

87 9.165 ofa pproved quality & make with necessary screws etc all complete.

Providing and fixing aluminium hanging floor door stopper, l5l

marked, anodised (anodic coatinS not less than grade AC 10 as per

89 9.101.2 15 : 1868) transparent or dyed to required colour and shade, with Each 75.00 66.19 4964.28 0.00

necessary screws etc. complete. Twin rubber stopper

Digitally signed by ANUJ

Providing and fixing bright finished brass 100 mm mortice latch and

lock, lSl marked, with six levers and a pair of anodised (anodic

90 9.103 coating not less than grade Ac 10 as per 15 : 1868) aluminium Each 2.00 786.63 1573.26 0.00

lever handles of approved quality with necessary screws etc.

Providing and fixing factory made uPVC white colour fixed glazed

windows/ventilators comprising of uPVC multi-chambered frame

and mullion (where ever required) extruded profiles duly reinforced

with 1.60 ± 0.2 mm thick galvanized mild steel section made from

roll forming process of required length (shape & size according to

uPVC profile), uPVC extruded glazing beads of appropriate

dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing

frame to finished wall, plastic packers, plastic caps and necessary

stainless steel screws etc. Profile of frame shall be mitred cut and

91 9.147B fusion welded at all corners, mullion (if required) shall be also

fusion welded including drilling of holes for fixing

hardware's and drainage of water etc. After fixing frame the gap

between frame and adjacent finished wall shall be filled with

weather proof silicon sealant over backer rod of required size and of

approved quality, all complete as per approved drawing & direction

of Engineer-in-Charge. (Single / double glass panes and silicon

sealant shall be paid separately).

Note: For uPVC frame, sash and mullion extruded profiles minus

5% tolerance in dimension i.e. in depth & width of profile shall be

92 acceptable. Variation in profile dimension in higher side shall be

accepted but no extra payment on this account shall be made.

Fixed window / ventilator made of (small series) frame 47 x 50mm

& mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm

93 9.147B.1 and single glazing bead of appropriate dimension. Sqm 35.82 7708.82 276129.88 0.00

(Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour casement/

Casement cum fixed glazed door comprising of uPVC multi-

chambered frame, sash and mullion (where ever required)

extruded profiles duly reinforced with 1.60 ± 0.2 mm thick

galvanized mild steel section made from roll forming process of

required length (shape & size according to uPVC profile), uPVC

extruded glazing beads of appropriate dimension, EPDM gasket,

zinc alloy (white powder coated) 3D hinges and one handle on each

side of panels along with zinc plated mild steel multi point locking

having transmission gear, cylinder with keeps and one side key, G.I

fasteners 100 x 8 mm size for fixing frame to finished wall and

94 9.147C necessary stainless steel screws, etc. Profile of frame & sash shall

be mitred cut and fusion welded at all corners, mullion (if required)

shall be also fusion welded including drilling of holes for fixing

hardware's and drainage of water etc. After fixing frame the gap

between frame and adjacent finished wall shall be filled with

weather proof silicon sealent over backer rod of required size and of

approved quality, all complete as per approved drawing & direction

of Engineer-in-Charge. (Single / double glass panes and silicon

sealent shall be paid separately). Variation in profile dimension in

higher side shall be accepted but no extra payment on this account

Note: For uPVC frame, sash and mullion extruded profiles minus

tolerance in dimension i.e. in depth & width of profile shall be

Casement door with 3D hinges made of (big series) frame

67 x 64 mm & sash 67 x 110 mm both having wall thickness

96 9.147C.1 of 2.3 ± 0.2 mm and single glazing bead / double glazing Sqm 33.60 10935.72 367440.24 0.00

bead of appropriate dimension. (Area of door upto 2.00 sqm).

Providing and fixing factory made uPVC white colour sliding glazed

window upto 1.50 m in height dimension comprising of uPVC multi-

chambered frame with in-built roller track and sash extruded

profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild

steel section made from roll forming process of required length

(shape & size according to uPVC profile), appropriate dimension of

uPVC extruded glazing beads and uPVC extruded interlocks, EPDM

gasket, wool pile, zinc alloy (white powder coated) touch locks with

hook, zinc alloy body with single nylon rollers (weight bearing

capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing

97 9.147D frame to finished wall and necessary stainless steel screws etc.

Profile of frame & sash shall be mitred cut and fusion welded at all

corners, including drilling of holes for fixing hardware's and

drainage of water etc. After fixing frame the gap between frame

and adjacent finished wall shall be filled with weather proof silicon

sealent over backer rod of

required size and of approved quality, all complete as per approved

drawing & direction of Engineer-in-Charge. (Single / double glass

panes, wire mesh and silicon sealent shall be paid separately)

Note: For uPVC frame and sash extruded profiles minus 5%

tolerance in dimension i.e. in depth & width of profile shall be

98 acceptable. Variation in profile dimension in higher side shall be

accepted but no extra payment on this account shall be made.

Three track three panels sliding window with fly proof SS

wire mesh (Two nos. glazed & one no. wire mesh panels)

made of (small series) frame 92 x 44 mm & sash 32 x 60 mm

99 9.147D.2 both having wall thickness of 1.9 ± 0.2 mm and single glazing Sqm 142.35 10665.22 1518193.78 0.00

bead of appropriate dimension (Area of window upto 1.75 sqm).

Digitally signed by ANUJ

Providing and fixing factory made uPVC white colour sliding glazed

door comprising of uPVC multi-chambered frame with in-built roller

track and sash extruded profiles duly reinforced with 1.60 ± 0.2

mm thick galvanized mild steel section made from roll forming

process of required length (shape & size according to uPVC profile),

appropriate dimension uPVC extruded glazing beads, uPVC

extruded interlock and uPVC extruded Inline sash adaptor (if

required), EPDM gasket, wool pile, zinc alloy (white powder coated)

handle with key on one side of extreme panels along with zinc

plated mild steel multi point locking having transmission gear with

keeps, zinc alloy (white powder coated) cresent lock (if required),

100 9.147F stainless steel (SS 304 grade) body with adjustable double nylon

rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x

8 mm size for fixing frame to finished wall and necessary stainless

steel screws etc. Profile of frame & sash shall be mitred cut and

fusion welded at all corners, including drilling of holes for fixing

hardware's and drainage of water etc. After fixing frame the gap

between frame and adjacent finished wall shall be filled with

weather proof silicon sealent over backer rod of required size and of

approved quality, all complete as per approved drawing & direction

of Engineer-in-Charge. (Single / double glass panes, wire mesh and

silicon sealent shall be paid separately).

Note: For uPVC frame and sash extruded profiles minus 5%

tolerance in dimension i.e. in depth & width of profile shall be

101 acceptable. Variation in profile dimension in higher side shall be

accepted but no extra payment on this account shall be made.

Three track three panels sliding door with fly proof S.S wire

mesh (Two nos. glazed & one no. wire mesh panels) made of

(big series) frame 116 x 45 mm & sash 46 x 82 mm both

102 9.147F.4 having wall thickness of 2.3 ± 0.2 mm and single glazing Sqm 28.80 9321.79 268467.60 0.00

bead / double glazing bead of appropriate dimension. (Area

of door above 2.00 sqm upto 5.00 sqm)

Providing and fixing fly proof stainless steel grade 304 wire gauge,

103 9.135 to windows and clerestory windows using wire gauge with average

width of aperture 1.4 mm in both directions with wire of dia. 0.50

mm all complete.

104 9.135.2 With 12 mm mild steel U beading Sqm 67.50 1118.33 75486.99 0.00

Providing and fixing 6 mm thick High performance glass door,

window, ventilator shutters and partitions etc. with PVC/neoprene

Based on gasket etc. complete as per the architectural drawings and the

DSR 21.3.2 directions of engineer-in-charge . (Cost of aluminium snap

beading shall be paid in basic item):

106 10.00 STEEL WORK

Providing and fixing 1mm thick M.S. sheet door with frame of

40x40x6 mm angle iron and 3 mm M.S. gusset plates at the

107 10.5.1 junctions and corners, all necessary fittings complete, including Sqm 5.04 5083.80 25622.34 0.00

applying a priming coat of approved steel primer. Using M.S. angels

40x40x6 mm for diagonal braces.

Providing and fixing pressed steel door frames conforming to IS:

4351, manufactured from commercial mild steel sheet of 1.60 mm

thickness, including hinges, jamb, lock jamb, bead and if required

angle threshold of mild steel angle of section 50x25 mm, or base

ties of 1.60 mm, pressed mild steel welded or rigidly fixed together

by mechanical means, including M.S. pressed butt hinges 2.5 mm

thick with mortar guards,lock strike-plate and shock absorbers as

specified and applying a coat of approved steel primer after pre-

treatment of the surface as directed by Engineer-in-charge:

Fixing with adjustable lugs with split end tail to each jamb

Steel work welded in built up sections/ framed work including

110 10.25 cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer using structural steel etc. as required

In stringers, treads, landings etc. of stair cases including use of

chequered plate wherever required, all complete.

In gratings, frames, guard bar, ladder, railings, brackets, gates and

Providing and fixing hand rail of approved size by welding etc. to

113 10.26.3 steel ladder railing, balcony railing, staircase railing and similar KG 100.00 191.61 19160.67 0.00

works, including applying priming coat of approved steel

primer.G.I. pipes

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box

for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid

of 1.5 mm thick M.S. sheet with its top surface hacked for proper

114 10.18 bonding, top lid shall be screwed into the cast iron/ M.S. sheet box Each 110.00 196.92 21661.55 0.00

by means of 3.3 mm dia round headed screws, one lock at the

corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape

as per standard drawing.

Providing and fixing carbon steel galvanised ( minimum coating 5

micron) dash fastener of 10 mm dia double threaded 6.8 grade

115 10.27 (yield strength 480 N/mm2), counter sunk head, comprising of 10

m dia polyamide PA 6 grade sleeve, including drilling of hole in

frame , concrete/ masonry, etc. as per direction of Engineer-in-

Providing and fixing stainless steel ( Grade 304) railing made of

Hollow tubes, channels, plates etc., including welding, grinding,

buffing, polishing and making curvature (wherever required) and

fitting the same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary accessories &

117 10.28 stainless steel dash fasteners , stainless steel bolts etc., of required KG 4048.00 651.01 2635269.96 0.00

size, on the top of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-in-charge, (for payment

purpose only weight of stainless steel members shall be considered

excluding fixing accessories such as nuts, bolts, fasteners etc.)

Digitally signed by ANUJ

Providing and fixing in position collapsible steel shutters with

vertical channels 20x10x2 mm and braced with flat iron diagonals

118 10.3 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, sqm 14.40 9992.20 143887.71 0.00

with 40 mm dia steel pulleys, complete with bolts, nuts, locking

arrangement, stoppers, handles, including applying a priming coat

of approved steel primer.

119 11.00 FLOORING WORK

Providing and laying Ceramic glazed floor tiles of size 300x300 mm

(thickness to be specified by the manufacturer), of 1st quality

conforming to IS : 15622, of approved make, in all colours, shades,

120 11.38 except White,Ivory, Grey, Fume Red Brown, laid on 20 mm thick Sqm 20.00 1177.13 23542.53 0.00

bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), including

pointing the joints with white cement and matching pigments

Providing and laying Vitrified tiles in floor in different sizes

(thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade, laid on

20 mm thick cement mortar 1:4 (1 cement:

4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm

including grouting the joints with white cement and matching

pigments etc. The tiles must be cut with the zero chipping diamond

cutter only . Laying of tiles will be done with the notch trowel, plier,

wedge, clips of required thickness, leveling system and rubber

mallet for placing the tiles gently

122 11.41A.2 Glazed vitrified floor tiles polished finish of size

Size of Tile 600 x 600 mm

124 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be

specified by manufacturer), with water absorption less than 0.08 %

and conforming to I.S. 15622, of approved make, in all colours &

126 11.46 shade, in skirting, riser ofsteps, over 12 mm thick bed of cement

mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint

with white cement & matching pigments etc. complete.

Grouting the joints of flooring tiles having joints of 3 mm width,

using epoxy grout mix of 0.70 kg of organic coated filler of desired

128 11.48 shade (0.10 kg of hardener and 0.20 kg of resin per kg), including

filling / grouting and finishing complete as per direction of Engineer-

Providing and laying flamed finish Granite stone flooring in required

design and patterns, in linear as well as curvilinear portions of the

building all complete as per the architectural drawings with 18 mm

thick stone slab over 20 mm (average) thick base of cement mortar

130 11.55 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry

and pointing with white cement slurry admixed with pigment of

matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge:

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown,

Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required

design and patterns, in linear as well as curvilinear portions of the

building all complete as per the architectural drawings with 18 mm

thick stone slab over 20 mm (average) thick base of cement mortar

132 11.56 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry

and pointing with white cement slurry admixed with pigment of

matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab jet black,cherry Red ,Elite Brown,Cat

Eye or equivalent

Providing and laying matt finished vitrified tile of size

300x300x9.8mm having with water absorption less than 0.5% and

conforming to IS: 15622 of approved make in all colours and

shades in for outdoor floors such as footpath, court yard, multi

134 16.89 modals location etc., laid on 20mm thick base of cement mortar Sqm 569.89 1329.92 757909.52 0.00

1:4 (1 cement : 4 coarse sand) in all shapes & patterns including

grouting the joints with white cement mixed with matching

pigments etc. complete as per direction of Engineer-in-Charge.

135 Badminton Court Flooring

Digitally signed by ANUJ

Supply & Installation of indoor wooden sports flooring with total

thickness of 75 mm comprising of 20mm Top Solid Wood followed

by 45mm solid wood runner and 10mm Power Rubber Pad. The

product should have BADMINTON WORLD FEDERATION (BWF)

approval with its usage as the indoor wooden sports floor. Product

top finish to have square Edge & UV Prefinished with Back Side

Coating (Polished used of Klumpps from Germany which is sweat

and saliva resistance according to DIN 53160-1/2) to have higher

polish life. The wooden flooring should have Eco-friendly

manufacturing process with 100% sustainable and manageable

plantation resource with raw material. The product should have

been produced through Kilned and dried technology to maintain

suitable moisture content. The top wood should neccessarily be

136 MR-24 sourced from 100% sustainable resource and should have factory Sqm 265.30 0.00 7079.00 0.00 1878058.70

polish in it. The technical parameters for the product should have

Gloss value (DIN EN ISO 2813) in the range of 33-34%,

inflammability (DIN 4102) with value B1, Cross Cut (Test DIN EN

ISO 2409) with value GT 0, Abrasion Resistance (DIN EN 438-2

(500g load per wheel S 33)) with value of IP-600cycle, Abrasion

Resistance (ASTM D 4060 (500g load per wheel CS 17)) with value

IP > 25000, Scratch Resistance Pencil Hardness (ISO 15184) with

value 3H, Scratch Resistance Coin Test (Hamberger planner) as

27N, Scratch Resistance Surface (Steel wool test Type 2) with

output of No Scratch / No Marking, Resistance to Indentation (DIN

EN 438 Part2-14) >= 2 Newton, Impact Resistance (DIN EN 438

Part2- 12) >= 2 Newton, Heat Resistance (EN 12722) with value of

120°C/ Rating 5, Reaction to Fire (EN 13226) with value as Efl, CE

PVC sport flooring for Badminton Court:

*100% PVC + Glass fibre + Imported fabric mesh

+6 layer flooring with anti water, antiskid, UVD layer, wear

137 MR-25 resistance & foam buffer. Sqm 594.84 0.00 2802.00 0.00 1666741.68

“Roll size — 15m x 1.8m

Thickness 4.5mm (Green)

*Would be installed over wooden flooring

* Inclusive of Game line marking

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate) finished with a floating coat of neat

138 11.3.1 cement, including cement slurry, but excluding the cost of nosing of Sqm 2788.05 579.50 1615670.79 0.00

steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

*Made of MS Pipe

*Made of 1.5" Round/Square Iron Pipe

*Garware Tournament quality Net - UV Treated.

Approx 14 Kgs each pair

GYM Flooring- Gym Rubber Roll

Thickness - 8mm Dynamic Impact

Great for large

Seamless joints

140 MR-34 Requires less cutting than tiles, especially custom cut rolls Sqm 279.24 0.00 3097.00 0.00 864806.28

Durable resilient rubber material

Use for home gym floors equipment

Commercial gym rubber under exercise Low thickness rubber

flooring option

Wide range of thicknesses available

Squash size: 1-1.2 M x 10 mm /roll

Supply & Installation of indoor wooden sports flooring with total

thickness of 75 mm comprising of 20mm Top Solid Wood followed

by 45mm solid wood runner and 10mm Power Rubber Pad. The

product should have BADMINTON WORLD FEDERATION (BWF)

approval with its usage as the indoor wooden sports floor. Product

top finish to have square Edge & UV Prefinished with Back Side

Coating (Polished used of Klumpps from Germany which is sweat

and saliva resistance according to DIN 53160-1/2) to have higher

polish life. The wooden flooring should have Eco-friendly

manufacturing process with 100% sustainable and manageable

plantation resource with raw material. The product should have

been produced through Kilned and dried technology to maintain

suitable moisture content. The top wood should neccessarily be

142 MR-27 sourced from 100% sustainable resource and should have factory Sqm 73.98 0.00 7079.00 0.00 523704.42

polish in it. The technical parameters for the product should have

Gloss value (DIN EN ISO 2813) in the range of 33-34%,

inflammability (DIN 4102) with value B1, Cross Cut [Test DIN EN

ISO 2409) with value GT D, Abrasion Resistance (DIN EN 438-2

(500g load per wheel S 33)) with value of IP-600cycle, Abrasion

Resistance (ASTM D 4060 (500g load per wheel CS 17)) with value

IP 25000, Scratch Resistance Pencil Hardness (ISO 15184) with

value 3H, Scratch Resistance Coin Test (Hamberger planner) as

27N, Scratch Resistance Surface (Steel wool test Type 2) with

output of No Scratch / No Marking, Resistance to Indentation (DIN

EN 438 Part2-14)> 2 Newton, Impact Resistance (DIN EN 438

Part2 12) 2 Newton, Heat Resistance (EN 12722) with value of

120C/Rating 5, Reaction to Fire (EN 13226) with value as Efl, CE

Supply and Application of Hard Plaster System meeting

specifications for Squash Court. The system consists of a 10 mm

base cement plaster (In client Scope) and top coat of upto 4mm

thickness to be provided by us in two layers. Due to extremely hard

143 MR-28 nature of plaster a slight uneven color distribution may be seen Sqm 116.17 0.00 3318.00 0.00 385452.06

once the plaster has dried, this doesn't affact the strength or

integrity of the plaster and must not be considered as a defect.

Area:- Wall plaster playing area is only below red lines totaling With

Squash Court Wall Painting for Play areas only

Supply and installation of approced free standing glass back wall

made of 12 mm thick toughened glass with four panels, 1 door, 4

144 MR-29 fines, fixtures and fittings and all the materials required for eracting LS 1.00 0.00 342643.00 0.00 342643.00

the glass walls. The height of the glass wall will be 2130 mm above

the finished floor level

Digitally signed by ANUJ

Supply and installation of 50W LED Batten Light (3ft) - 21 Nos with

1.5 Sq.mm 2 core cable coil, Cabling, Mounting Structure & Switch

145 MR-30 Board including Installation cabling & mounting structure and LS 1.00 0.00 171321.00 0.00 171321.00

switch boards for LED

#Electrical Source to be provided by client

"Supply and installation of 6400 mm width X 480 mm height with

wall mounting thickness of 25 mm sound Board made out of

146 MR-31 powder coated galvanized sheet of 24 gauge thickness, fixed with LS 1.00 0.00 21244.00 0.00 21244.00

wooden frame work and fitting etc., all complete for Squash

147 12.00 ROOFING

Providing and laying gola 75x75mm in cement concrete M15 grade

148 12.21 including finishing with cement mortar 1:3 (1 cement : 3 fine sand) rmt. 378.60 276.67 104747.51 0.00

as per standard design in 75x75 mm deep chase.

Providing and fixing false ceiling at all height including providing

and fixing of frame work made of special sections, power pressed

from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats

of size 25 mm wide x 1.6 mm thick with

flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm

long with 6 mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the

spacing of 1200 mm centre to centre, to which the ceiling section

0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26

149 12.45 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall

be fixed in a direction perpendicular to G.I. intermediate channel

with connecting clips made out of

2.64 mm dia x 230 mm long G.I. wire at every junction, including

fixing perimeter channels 0.5 mm thick 27 mm high having flanges

of 20 mm and 30 mm long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at 450 mm centre, with 25

mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the

help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,

jointing and finishing to a flush finish of tapered and square edges

board with recommended jointing compound , jointing tapes ,

12.5 mm thick tapered edge gypsum plain board conforming

Providing and Fixing 15 mm thick densified tegular edged eco

friendly light weight calcium silicate false ceiling tiles of approved

texture spintone/cosmos / Hexa or equivalent of size 595 x 595

mm in true horizontal level,suspended on inter locking metal grid of

hot dipped galvanised steel sections (galvanising @ 120 grams per

sqm including both side) consisting of main ‘T’ runner suitably

spaced at joints to get required length and of size 24x38 mm made

from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to

centre, and cross “T” of size 24x28 mm made out of 0.33 mm

(Minimum) sheet, 1200 mm long spaced between main’T’ at 600

151 12.53 mm centre to centre to form a grid of 1200x600 mm and secondary

cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm

thick (Minimum)

sheet to be inter locked at middle of the 1200x 600 mm panel to

from grid of size 600x600 mm, resting on periphery walls

/partitions on a Perimeter wall angle pre-coated steel of

size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet

with the help of rawl plugs at 450 mm centre to centre with 25 mm

long dry wall screws @ 230 mm interval

and laying 15 mm thick densified edges calicum silicate ceiling tiles

of approved texture (Spintone / Cosmos/hexa) in the grid,

including, cutting/ making opening for services like diffusers, grills,

light fittings, fixtures, smoke detectors etc., wherever required.

Main ‘T’ runners to be suspended from ceiling using G.I. slotted

cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and

50 mm long dash fasteners, 4 mm G.I. adjustable rods with

galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at

1200 mm centre to centre along main ‘T’, bottom exposed with 24

mm of all Tsections shall be pre-painted with polyster baked paint,

for all heights, as per specifications, drawings and as directed by

engineer-in-charge.

153 MR-17 Anutone Soak Cord Triangle 600x600x15mm, Square edge

Supply and Installation of Anutone Soak Cord Triangle, square

edge, two color fabric wrapped diagonally (choiced colours),

154 pinewood fiber core panel of size 600x600x15mm,with ribbed

finish, volume density 400Kgs/m3, weight 6kg/m2 installed by

using Anutone Strut framework system and Anutone Strut Z bars.

The Anutone Strut framework systems includes Anutone Strut

CC25 Cross Channel having thickness 0.55mm, length 3600mm,

knurled web 35, depth 20mm and equal flanges 15mm is fastened

to wall positioned vertically in a regular manner at 600mm c/c.

Anutone Strut Z bar having 40mm height, thickness 1mm is first

fixed behind the panels by using suitable fasteners. Another length

155 of Strut Z bar to be fastened perpendicular to Strut CC25 Cross

Channel at spacing so as to match with that of Strut Z bar rear to

panels. Soak cord Triangle, square edge panels are then slided on

to Strut Z bar fixed on Strut CC25 Cross Channel.

Note: Thickness is given for bare Panels, 4mm for cord

fabric.(fabric colour as per choice)

The system is backlined with the acoustical infill Anutone SynthPF

157 Technical Parameters

Digitally signed by ANUJ

• Fire (Class) – 1

• Acoustics – NRC 0.75

• Climate (°C, RH) – 50, 90

• Light reflectance (%) – colour dependant

• Green (VOC, RC %) – Low, 30

159 MR-18 Anutone Soak Cord 600x2400x20mm, Kerfed edge

Supply and Installation of Anutone Soak Cord, square edge, fabric

wrapped pinewood fiber panel of size 600x2400x20mm, density

160 400 kgs/m3, weight 8kg/m2 installed by using Anutone Strut

framework system with non-visible fasteners using Anutone Strut H-

The Anutone Strut framework systems includes Anutone Strut

CC25 Cross Channel having thickness 0.55mm, length 3600mm,

knurled web 35, depth 20mm and equal flanges 15mm is fastened

to wall positioned vertically in a regular manner at 600mm c/c..

Anutone Strut H-Spline having sectional thickness 2mm and length

2400mm to be fixed perpendicular to the Strut CC25 Cross Channel

at 600mm centers. The Kerfed edge fabric wrapped panels shall be

then inserted into the Strut H-spline along their long edges of

2400mm against framework to perfect fit with staggered short

Note: Thickness is given for bare Panels, 4mm for cord

fabric.(fabric colour as per choice)

Optional: The system is backlined with the acoustical infill Anutone

163 Technical Parameters

• Fire (Class) – 1 & P

• Acoustics – NRC 0.95 (For 25mm C50 Mounting)

• Climate (°C, RH) – 50, 90

• Light reflectance (%) – colour dependant

• Green (VOC, RC %) – Low, 30

For execution of works contact for Laying of Proflex Roof

with Material on your building

BAY 1 : NLU INDOOR STADIUM

Dead Load : 0 kg/Sqm

(a) Span (in Meters): 15.95

(b) Arch Rise (in Meters): (SPAN/5 ) 3.15

(c) Length (in Meters): 27.14

(e) No Of Bays : 2

(f) Area per Bay in SQM: 520

(g) Height (in Meters): 7.50

Material Specification

BM : Imported /Colour Coated Galvalume

BMT : 1.00 mm ; APT: 1.05 mm

Tolerance : +-0.04mm

WIDTH : 912mm ; Tolerance : +-4mm

YST (Yield strength): 350 Mpa

166 13.00 FINISHING WORK

167 13.4 12 mm cement plaster of mix :

18 mm cement plaster in two coats under layer 12 mm thick

169 13.11 cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top Sqm 5041.94 470.78 2373624.72 0.00

layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Add or deduct for plaster drip course/ groove in or moulding to

R.C.C. projections.plastered surface

171 13.16 6 mm cement plaster of mix :

Extra for providing and mixing water proofing material in cement per bag

plaster work in proportion recommended by the manufacturers. of 50KG

13.26 Providing and applying plaster of paris putty of 2 mm

174 13.26 thickness over plastered surface to prepare the surface even and Sqm 7543.44 227.87 1718887.39 0.00

smooth complete

Wall painting with plastic emulsion paint of approved brand and

manufacture to give an even shade

Finishing walls with Premium Acrylic Smooth exterior paint with

Silicone additives of required shade:

New work (Two or more coats applied @ 1.43 ltr/10 sqm

177 13.47.1 over and including priming coat of exterior primer applied Sqm 732.29 172.63 126412.85 0.00

178 13.50 Applying priming coat :

With ready mixed red oxide zinc chromate primer of approved

179 13.50.3 brand and manufacture on steel galvanised iron/ steel works Sqm 212.90 59.01 12563.90 0.00

Providing and applying white cement based putty of average

180 13.80 thickness 1 mm, of approved brand and manufacturer, over the Sqm 659.70 131.69 86875.70 0.00

plastered wall surface to prepare the surface even and smooth

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

182 13.61.1 Two or more coats on new work Sqm 212.90 139.77 29757.20 0.00

French spirit polishing: Two or more coats on new works including

a coat of wood filler.

Providing and fixing GI hexagonal chicken wire mesh of size 12mm

x22g at the junction of disimilar surfaces of brick masonry wall and

184 MR R C C column by beams and the like including necessary nails for Sqm 843.47 0.00 125.00 0.00 105433.75

fixing etc, complete all as per specification and direction of Engineer

-in -charge for all floor at all heights.

185 21.00 ALUMINIUM WORK

Digitally signed by ANUJ

Providing and fixing aluminium work for doors, windows, ventilators

and partitions with extruded built up standard tubular

sections/appropriate Z sections and other sections of approved

make conforming to IS: 733 and IS : 1285, fixed with rawl plugs

and screws or with fixing clips, or with expansion hold fasteners

including necessary filling up of gaps at junctions, at top, bottom

186 21.1 and sides with required PVC/neoprene felt etc. Aluminium sections

shall be smooth, rust free, straight, mitred and jointed echanically

wherever required including cleat angle, Aluminium snap beading

for glazing / paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the directions of

Engineer-in-charge. Glazing and paneling to be paid for separately)

187 21.1.1 For fixed portion.

Powder coated aluminium (minimum thickness of powder coating

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket

189 21.3 etc. complete as per the architectural drawings and the directions

of engineer-in-charge . (Cost of aluminium snap beading shall be

paid in basic item):

With float glass panes of 5.5 mm thickness (weight not less than

191 22.00 WATER PROOFING WORKS

Providing and laying water proofing treatment in sunken portion of

192 22.5 WCs, bathroom etc., by applying cement slurry mixed with water

proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with

water proofing cement compound @ 0.253 kg/ sqm. This layer will

be allowed to air cure for 4 hours. (b) Second layer of slurry of

cement @ 0.242 kg/sqm mixed with water proofing cement

193 compound @ 0.126 kg/sqm. This layer will be allowed to air cure SQM 79.26 549.30 43537.58 0.00

for 4 hours followed with water curing for 48 hours. The rate

includes preparation of surface, treatment and sealing of all joints,

corners, junctions of pipes and masonry with polymer mixed slurry.

Providing & laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs,

balconies, terraces etc consisting of following operations: a)

Applying a slurry coat of neat cement using 2.75kg/sqm of cement

admixed with water proofing compound confirming to IS. 2645 and

approved by Engineer-in-charge over the RCC slab including

adjoining walls upto 300mm height including cleaning the surface

before treatment. b) Laying brick bats with mortar using broken

bricks/brick bats 25mm to 115mm size with 50% of cement mortar

1:5 (1 cement : 5 coarse sand ) admixed with water proofing

compound confirming to IS : 2645 and approved by Engineer-in-

charge over 20 mm thick layer of cement of 1:5 ( 1 cement : 5

coarse sand ) admixed with water proofing compound confirming to

IS : 2645 and approved by Engineer-in-charge to required slope

and treating similarly the

adjoining walls upto 300mm height including rounding of junctions

of walls and slabs. c) After two days of proper curing applying a

second coat of cement slurry using 2.75kg/sqm of cement admixed

with water proofing compound confirming to IS : 2645 and

approved by Engineer-in-charge. d) Finishing the surface with 20

mm thick jointless cement mortar 1:4 (1 cement : 4 coarse sand )

admixed with water proofing compound confirming to IS : 2645

195 and approved by Engineer-in-charge including laying glass fibre

cloth of approved quality in top layer and finally finishing the

surface with trowel with neat cement slurry and making pattern of

300x300 mm square 3mm deep. e) The whole terrace so finished

shall be flooded with water for a minimum period of two weeks for

curing and for final test. All above operations to be done in order

and as directed and specified by the Engineer-in-charge:

With average thickness of 120mm and minimum thickness at

khurra as 65mm.

Providing and applying integral crystalline slurry of hydrophilic in

nature for waterproofing treatment to the RCC structures like

retaining walls of the basement, water tanks, roof slabs, podiums,

reservior, sewage & water treatment plant, tunnels / subway and

bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts

integral crystalline slurry : 2 parts water) for vertical surfaces and 3

: 1 (3 parts integral crystalline slurry : 1 part water) for horizontal

surfaces and applying the same from negative (internal) side with

the help of synthetic fiber brush. The material shall meet the

197 22.23 requirements as specified in ACI-212-3R-2010 i.e by reducing

permeability of concrete by more than 90% compared with control

concrete as per DIN 1048 and resistant to 16 bar hydrostatic

pressure on negative side. The crystalline slurry shall be capable of

self-healing of cracks up to a width of 0.50mm. The work shall be

carried out all complete as per specification and the direction of the

engineerin- charge. The product performance shall carry guarantee

for 10 years against any leakage.

198 22.23.1 For vertical surface two coats @0.70 kg per sqm Sqm 225.87 431.97 97568.08 0.00

199 22.23.2 For horizontal surface one coat @1.10 kg per sqm. Sqm 60.66 331.22 20091.68 0.00

Digitally signed by ANUJ

Providing & Applying high quality acrylic modified resin based

of Dholpur/Red sand stone Pattern with anti algae and UV

properties to be applied as intermediate finish in desired pattern @

43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after

and properly cleaning the surface to remove loose particles from

plaster surface, followed by top coating with Premium Acrylic

exterior paint with Silicone additives of required shade by two or

more coats @ 1.43 litres/10 sqm, complete as the direction of

Engineer -in-Charge.

STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL

Providing and supplying aluminium extruded tubular and other

aluminium sections as per the architectural drawings and approved

shop drawings , the aluminium quality as per grade 6063 T5 or T6

per BS 1474,including super durable powder coating of 60-80

microns conforming to AAMA 2604 of required colour and shade as

approved by the Engineer-in-Charge. ( The item includes cost of

material such as cleats, sleeves, screws etc. necessary for

fabrication of extruded aluminium frame work. Nothing extra shall

be paid on this account). The weight of aluminium extruded section

shall be taken for purpose

Designing, fabricating, testing, protection, installing and fixing in

position semi (grid) unitized system of structural glazing (with open

joints) for linear as well as curvilinear portions of the building for all

heights and all levels, including:

(a) Structural analysis & design and preparation of shop drawings

for the specified design loads conforming to IS 875 part III (the

system must passed the proof test at 1.5 times design wind

pressure without any failure), including functional design of

the aluminum sections for fixing glazing panels of various

thicknesses, aluminium cleats, sleeves and splice plates etc.

gaskets, screws, toggles, nuts, bolts, clamps etc., structural

and weather silicone sealants, flashings, fire stop (barrier)-

cum-smoke seals, microwave cured EPDM gaskets for water

203 25.2 tightness, pressure equalisation & drainage and protection

against fire hazard including:

(b) Fabricating and supplying serrated M.S. hot dip galvanised /

Aluminium alloy of 6005 T5 brackets of required sizes, sections

and profiles etc. to accommodate 3 Dimentional movement

for achieving perfect verticality and fixing structural glazing

system rigidly to the RCC/ masonry/structural steel framework

of building structure using stainless steel anchor fasteners/

bolts, nylon seperator to prevent bimetallic contacts with nuts

and washers etc. of stainless steel grade 316, of the required

capacity and in required numbers.

(c) Providing and filling, two part pump filled, structural silicone

sealant and one part weather silicone sealant compatible with

the structural silicone sealant of required bite size in a clean

(d) Providing and fixing in position flashings of solid aluminium

sheet 1 mm thick and of sizes, shapes and profiles, as required

as per the site conditions, to seal the gap between the building

structure and all its interfaces with curtain glazing to make it

204 watertight.

(e) Making provision for drainage of moisture/ water that enters

the curtain glazing system to make it watertight, by

incorporating principles of pressure equalization, providing

suitable gutter profiles at bottom (if required), making necessary

holes of required sizes and of required numbers etc. complete.

This item includes cost of all inputs of designing, labour for

fabricating and installation of aluminium grid, installation of

glazed units, T&P, scaffolding and other incidental charges

including wastages etc., enabling temporary structures and

services, cranes or cradles etc. as described above and as

specified. The item includes the cost of getting all the structural

and functional design including shop drawings checked by a

structural designer, dully approved by Engineer-in-charge. The

205 item also includes the cost of all mock ups at site, cost of all

samples of the individual components for testing in an approved

laboratory, field tests on the assembled working structural

glazing as specified, cleaning and protection till the handing

over of the building for occupation. In the end, the Contractor

shall provide a water tight structural glazing having all the

performance characteristics etc. all complete as required, as

per the Architectural drawings, as per item description, as

specified, as per the approved shop drawings and as directed

by the Engineer- in-Charge.

Digitally signed by ANUJ

Note:- 1. The cost of providing extruded aluminium frames,

shadow boxes, extruded aluminium section capping for fixing

in the grooves of the curtain glazing and vermin proof stainless

steel wire mesh shall be paid for separately under relevant

items under this sub- head. However, for the purpose of

payment, only the actual area of structural glazing (including

width of grooves) on the external face shall be measured in

sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted

206 on structural glazing system if area of structural glazing

exceeds 2500 Sqm from the certified laboratories

accreditated by NABL(National Accreditation Board for

Testing and Calibration Laboratories), Department of

Science & Technologies, India. Cost of testing is payable

The NIT approving authority will decide the necessity of testing

on the basis of cost of the work, cost of the test and importance

of the work. Performance Testing of Structural glazing system

Tests to be conducted in the NABL accredited lab or any other

accreditation body which operates in accordance with ISO/

IEC 17011 and accredits labs as per ISO/IEC 17025

1. Performance Laboratory Test for Air Leakage Test (-50pa

to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04

testing method for a range of testing limit 1 to 200 mVhr

2. Static Water Penetration Test. (50pa to 1500pa) as

per ASTME- 331-09 testing method for a range up to

3. Dynamic Water Penetration (50pa to 1500pa) as per

207 AAMA 501.01- 05 testing method for a range upto Sqm 91.27 3308.40 301958.10 0.00

4. Structural Performance Deflection and deformation by

static air pressure test (1.5 times design wind pressure

without any failure) as per ASTME-330-10 testing method

for a range upto 50 mm

5. Seismic Movement Test (upto 30 mm) as per AAMA

501.4-09 testing method for Qualitative test, Tests to be

conducted on site.

6. Onsite Test for Water Leakage for a pressure range 50

kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs)

comprising of hermetically-sealed 6-12- 6 mm insulated glass

glazed) vision panel units of size and shape as required and

comprising of an outer heat strengthened float glass 6mm thick, of

approved colour and shade with reflective soft coating on surface #

of approved colour and shade, an inner Heat strengthned clear float

glass 6mm thick, spacer tube 12mm wide, dessicants, including

primary seal and secondary seal (structural silicone sealant) etc. all

complete for the required performances, as per the Architectural

drawings, as per the approved shop drawings, as specified and as

208 25.3 directed by the Engineer-in-Charge. The IGUs shall be assembled in Sqm 91.27 3591.30 327777.56 0.00

the factory/ workshop of the glass processor.

(Payment for fixing of IGU Panels in the curtain glazing is included

cost of item No.25.2)

For payment, only the actual area of glass on face # 1 of the glass

panels (excluding the areas of the grooves and weather silicone

sealant) provided and fixed in position, shall be measured in sqm.

(i) Coloured tinted float glass 6mm thick substrate with reflective

soft coating on face # 2, + 12mm Airgap + 6mm Heat

Strengthened clear Glass of approved make having properties

as visible Light transmittance (VLT) of 25 to 35 %, Light

reflection internal 10 to 15%, light reflection external 10 to 20

%, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/

Extra for openable side / top hung vision glass panels (IGUs)

providing and supplying at site all accessories and hardwares for

openable panels as specified and of the approved make such as

heavy duty stainless steel friction hinges, min 4 -point cremone

locking sets with stainless steel plates, handles, buffers etc.

necessary stainless steel screws/ fasteners, nuts, bolts, washers

etc. all complete as per the Architectural drawings, as per the

shop drawings, as specified and as directed by the Engineer- in

210 MISCELLANEOUS WORK

Providing and fixing dry cladding of Laterite Tile (Thickness 18 to

20mm) Size-6x12 inch / 4x12 inch gang saw cut stone, fixed to

211 MR-6 structural steel frame work (to be paid separately) and /or with the Sqm 460.00 0.00 4164.08 0.00 1915476.80

help of cramps, pins etc. sealing the joints with approved weather

sealant as per architectural drawing and direction of engineer -in-

Digitally signed by ANUJ

Providing and fixing structural steel frame (for dry cladding with 30

mm thick gang saw cut with machine cut edges sand stone) on

walls at all heights using M.S. square/ rectangular tube in the

required pattern as per architectural drawing, including cost of

cutting, bending, welding etc. The frame work shall be fixed to the

wall with the help of M.S. brackets/ lugs of angle iron/ flats etc.

which shall be welded to the frame and embedded in brick wall with

cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded

stone aggregate 20 mm nominal size) of size 300x230x300 mm,

including cost of necessary centring and shuttering and with

DSR approved expansion hold fasteners on CC/RCC surface, including

212 drilling necessary holes. Approved cramps/ pins etc. shall be KG 4600.00 233.93 1076059.60 0.00

welded to the frame work to support stone cladding, the steel work

will be given a priming coat of Zinc primer as approved by

Engineerin- charge and painted with two or more coats of epoxy

paint (Shop drawings shall be submitted by the contractor to the

Engineer-in-charge for approval before execution). The frame work

shall be fixed in true horizontal & vertical lines/planes. (Only

structural steel frame work shall be measured for the purpose of

payment, stainless steel cramps shall be paid for separately and

nothing extra shall be paid).

Providing and fixing adjustable stainless steel cramps of approved

quality, required shape and size, adjustable with stainless steel

DSR nuts, bolts and washer (total weight not less than 260 gms), for dry

213 stone cladding fixed on frame work at suitable location, including Each 2760.00 388.80 1073075.98 0.00

making necessary recesses in stone slab, drilling required holes etc

complete as per direction of the Engineer-in-charge..

Providing and fixing double scaffolding system (cup lock type) on

the exterior side, up to seven story height made with 40 mm dia

M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining

with cup & lock system with M.S. tubes, M.S. tube challies, M.S.

clamps and M.S. staircase system in the scaffolding for working

platform etc. and maintaining it in a serviceable condition for the

required duration as approved and removing it there after .The

scaffolding system shall be stiffened with bracings, runners,

connection with the building etc wherever required for inspection of

work at required locations with essential safety features for the

workmen etc. complete as per directions and approval of

charge .The elevational area of the scaffolding shall be measured

214 14.72 for payment purpose .The payment will be made once irrespective Sqm 460.00 303.04 139398.63 0.00

duration of scaffolding.

Note: - This item to be used for maintenance work judicially,

necessary deduction for scaffolding in the existing item to be done.

Providing, fixing, and installing,13 passenger elevator, Lift well size -

2100(W) x 2.45 (D), No. of Stops - 3, Openings-3, Ground Floor to

2nd Floor Height- 3.6M, Clear Door Opening- 900mm, Speed of Lift -

1.5M/s, Vision Panel, Automatic rescue device, etc., with all

necessary features,WITH machine room less ,Stainless Steel Vandal

proof Finish,all complete as per specification and instruction of

Engineer in charge. The work also include all building/ structural

works for supporting arrangement system, necessary scaffolding

required for erection of the complete system, necessary wiring

and installation of lighting for lift well and lift pit, providing ladder in

the lift pit etc. as required complete.

Providing & fixing 12mm clear Toughened glass on wall connecting

Profile fitting upto 3050 height. Fixing with Safety type on all three

216 MR-19 sides, below will be fixed by making a groove on the floor with all Sqm 460.00 0.00 8429.00 0.00 3877340.00

necessaries accessories required like SS Screws, Silicones, Masking

Tape, Abro Tape complete only. Execution as per approved design.

Providing & fixing Hardware for floor mounted glass door (Floor

package weight :- 120 Kgs). Door Hardwares package includes Top

217 MR-20 over panel patch, top corner patch, top patch, Bottom Patch, Floor Set 20.00 0.00 19873.00 0.00 397460.00

Lock, Floor spring, Handle H-type 600mm.

Providing & Fixing of Aluminum Composite Panel ( ACP ) over

Aluminium section, Main Mulian of size 38mmx25mm, ACP

218 MR-21 thickness 4mm with .25 skin thickness, accessories silicon Dow Sqm 124.00 0.00 3838.00 0.00 475912.00

Coring 789, fastener & masking tape AL Angle, MS Angle ,Pressure

Tape & Screw of Standard company.

Steel work in built up tubular (round, square or rectangular hollow

etc.) trusses etc., including cutting, hoisting, fixing in position and

219 10.16.1 applying a priming coat of approved steel primer, including welding KG 1736.00 164.71 0.00 285928.18 0.00

bolted with special shaped washers etc. complete

Hot finished welded type tubes

Providing and fixing artistic mural in glass Mosaic of size 20x20mm.

220 MR-22 Rate inclusive of fixing mosaic with adhesive cement, grout & Sqm 120.00 0.00 11797.87 0.00 1415743.99

labour required for installation.

221 MR-13 Providing & installation of following signages :

222 1 Entry Exit Totem , Modular Totem (5000x1220x300) Each 2.00 0.00 191879.80 0.00 383759.60

Informative Pole Sign, MPO POLE 80mm WITH IDDS 50mm

Building Name Pole Signs, MPO 80mm Nonlite (450x450x1800)

Entry Welcome sign, I SIGN DISPLAY 24 MM (500x1000x24)

Digitally signed by ANUJ

228 7 Wall Projected Sign, MPI PROJECTED (250x156x12) Each 12.00 0.00 1918.80 0.00 23025.58

229 8 Passage Suspended Sign, MPI SUSPENDED (900x156x20) Each 12.00 0.00 6030.51 0.00 72366.10

230 9 Directory Sign, MPI DIRECTORY (500x1000x15(Approx)) Each 12.00 0.00 21929.12 0.00 263149.44

233 12 Lift In Case Of Fire Use Stair Sign, MPI/WM (300x156x12) Each 4.00 0.00 1233.51 0.00 4934.05

234 13 Fire Extinguisher Sign, MPI /WM (250x187x12) Each 4.00 0.00 1233.51 0.00 4934.05

235 14 Emergency Exit Sign, MPI /WM (250x187x12) Each 4.00 0.00 3769.07 0.00 15076.27

236 15 Brass rose gold letter,(400 mm Height) Each 35.00 0.00 3179.72 0.00 111290.28

237 Cricket Ground Equipments

Providing Fitting and Fixing of Cricket Fixed Practice Net Cage for 3

238 MR-1 Pitches of Size 50'x30'x13' - Made up of 1.5 inches round heavy Each 1.00 0.00 348635.84 0.00 348635.84

duty ms pipe, automotive paint , 2.5 mm thick /50mm mesh

Providing Fitting and Fixing Special Cricket Cemented Pitch of Size

239 MR-2 10'x50'- One Pitch , Product code CP-C, Digging up to 5"deep, Each 500.00 0.00 356.35 0.00 178174.10

Leveling, Dressing, Earth cutting for cemented pitch, layer of brick

blast 5" thick, RCC of 3" as top layer

Providing Fitting and Fixing Construction of Cricket Turf Pitch

240 MR-3 (Practice wickets) - Two Extra Bounce Pitches of Size 10'X50' With Each 1000.00 0.00 500.26 0.00 500258.05

Material. Total area 500X2=1000 Sq Ft (Product Code - CP-T or

Supply and Installation of One Astro Turf - High Quality

241 MR-4 10mm Special Cricket Astro Turf with Adhessive and Line Each 330.00 0.00 230.26 0.00 75984.40

marking. Size 10X33 ft

Providing Fitting and Fixing of Cricket Pitch Roller Manual 750Kg

242 MR-5 Capacity - Product Code - RM-750 (Dry weight 400Kg) Each 1.00 0.00 110574.80 0.00 110574.80

Providing Fitting and Fixing of Cricket Pitch EV Roller 1.5Ton

243 MR-6 Capacity - (Product Code EV-1.5T DW or equivalent) Each 1.00 0.00 643935.60 0.00 643935.60

Providing Fitting and Fixing of Original Pitch Cover 650GSM- For 3

244 MR-7 Pitches Size 60'X100' ft (Product Code - PCS 630 or equivalent) Each 6000.00 0.00 37.73 0.00 226353.12

Providing Fitting and Fixing of Cricket Pitch Grass Cutting Manual

246 MR-9 Providing & installation of Lawn mower Each 1.00 0.00 474821.20 0.00 474821.20

Supply And Installation of Cricket LED Score Board of size approx

Providing Fitting and Fixing of Boundary Rope Product Code BRP -

34 -> one roll contains 220 mtr rope. Total 2 Rolls.

Providing Fitting and Fixing of GI Sight Screens - Supply of 2 sight

249 MR-12 screens size 15X20ft, made up of GI sheet, MS frame, Heavy duty Each 2.00 0.00 214645.20 0.00 429290.40

turf wheels, Ome side Black , one side white

Providing Fitting and Fixing of Trg Equipments (As per suggested

Providing Fitting and Fixing Irrigation Syatem for 65 mtr Ground -

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over areas

(up to 30mm in depth. 1.5 m in width as well

253 MR as 10 sqm on plan) including disposal of

excavated earth lead upto 50m and lift upto 1.5m,

disposed earth to be leveled and neatly dressed. All kind of soil

surface dressing of the ground including removing

254 vegetation and inequalities not exceeding 15 cm deep

and disposal of rubbish lead up to 50 m and lift up to

1.5 m. All kind of soil

Ploughing the existing ground to a depth of 15 cm to 25

cm and watering the same. All kind of soil

Providing herbicide three application by mechanical

sprayer with Glyphosate (Roundup, Casonova make)

256 500g (active) / per liter water mix applied at 2 liter/per

hectare per one time application or as manufacturer's

specification and slashing in works areas for weed

control, as directed by engineer-in-charge.

Rough shaping, Leveling, neatly dressing and finishing

257 the top smooth with desired slope of earth as per

direction of engg. Charge.

Diluting and injecting chemical emulsion for Antitermite

treatment under soil using chlorpyriphos/ E.C. 20%

258 with 1% concentration using 10 ml of chemical in 10

ltrs. Of water in 1 sqm. Of area as per direction of

filling in plinth with available soil in including watering,

ramming, consolidating and dressing complete. Picking

of stones/ and undesired material from filled sand

259 ,Fine shaping of the sand by carrying, filling &

spreading as per requied depth and shape and

finishing the top smooth with desired slope/profile as

per direction of engg. In Charge.

Supplying and mixing of Organic Matter in the soil @

260 1kg per sqm. Of neam cake/coco peat/leaf manuer to

make a root zone mix complete as per engg. In charge.

Supplying & Laying Basal Fertilization & Starter

261 fertilizer i.e 2kg per 100 sqm. Of DAP, 1kg per 100

sqm. Of sulphate of potas, forate/thaimate 0.5 kg per

100 sqm. liquid and water soluble fertilizer.

Supplying and grassing by dibbling/sprigging of stolens

of bermuda VAR including Raking & smoothing.

263 MR MAIN PITCH (3.25mx25mX3 Pitches)

264 PITCH SOIL

Earth work in excavation by mechanical means (Hydraulic

265 excavator)/ manual means over areas (exceeding 15 cm in

depth) including getting out and disposal of excavated earth , as

directed by Engineer-incharge.All kinds of soil

Supply and Laying of Brick blast 100mm . supply of all labour,

266 also includes dressing leveling and compaction.

Supply and Laying special Blocks of size 600x600X75mm for

267 extra bounce. supply of all labour, also includes dressing

leveling and compaction.

Supply and Laying of special rubber sheets (inside Fiber Thread).

Supply and installation of all labour.

Supply and Laying of special rubber sheets (inside Fiber Thread).

Supply and installation of all labour.

Digitally signed by ANUJ

270 Hire Charges for Smooth Wheeled Roller 0.5 to 5 tonne

271 Hire Charges for Surface Vibrator

Labour charges for Coolie (Required for breaking pitch

soil into desire size)

Labour charges for Beldar (Laying and compacting pitch soil )

supplying and grassing by dibbling/sprigging of stolens of

selection no.1 grass including Raking & smoothing.

Grow in period maintenance to make a firm, smooth & finish

playing surface for a period of 15 days from the completion of

work(grassing) including maintain the growth of grass till first

275 cutting ,at the time of grow-in maintenance. LS 225.00 0.00 9319.88 0.00 2096972.10

Providing and laying 15 mm EPDM Jogging Track, Running Track,

PLAYGROUND/ OPEN GYM SAFETY FLOORING EPDM GRANULES of

make BSG, NOVAL, manufactured under quality management

system of ISO 9001.2015 or above having polymer content 20-22

% or above , High UV rating min 3-4/5 on grayscale, VOC less than

3.0g/Combustibility less than40 mm/min test method UL-94HB,

elongation at break more than 500 %, REACH/SVHC & ROHS

COMPLIANT, ANTIMICROBIAL & ANTIFUNGAL TESTED MATERIAL ,

276 MR standard grain size 1.0-3.5mm. laying in three layers. i.e Layer 1- Sqm 3130.00 0.00 3244.41 0.00 10155013.64

Polyurethane based primer coating. Layer 2-19 mm black rubber

base particle long rubber stands/ sbr rubber crumb mix with 15 %

single competent PU base binder styrene butadiene

rubber/synthetic rubber. Layer 3-6mm COLORED EPDM GRANULES

chemically bonded with MDI with 19-20% 'single component of

Diphenylmethane Discarnate and paraffinic oil etc. Designs as per

engineer in charge.

277 High Mast Sports Lighting

Lighting- Supply and Installations of LED Flood Lights luminaire

conforming to the technical specifications as mentioned

below(Additional accessories needs to be ordered seperately) Make:

Philips - BVP486 ( 24 Luminaires Per Mast )Supply of LED Floodlight

luminaire with a housing of non-corrosive high pressure ADC with

corrosion resistant powder coating and Anti-dust exposed Lens to

ensure protection. The luminaire should have CRI > 70, SDCM <5

and CCT of 5700K and shall be compliant with IP66 and IK08

classification. Luminaire shall be designed to emit at least 126900

nominal lumens with maximum system wattage of 940W at a

system efficacy of atleast 135 lumen/watt. The luminaire shall be

designed so as to ensure lumen depreciation of up to 30% over 75k

burning hours @ design ambient temp 35 deg C. The luminaire

278 MR should have Unique Integrated Peanut Lens Optics to get the choice Each 96.00 0.00 111016.17 0.00 10657552.32

of Narrow beam, symmetrical wide and asymmetrical wide beam

suiting various applications with exposed PC optic lens. The

luminaire should have fins on the back to ensure good heat

dissipation and to prevent dirt from settling on the luminaire along

with aiming angle scale. The electronic driver should be fully

integrated and shall have a power factor >0.95 and THD <10%

with a minimum inbuilt surge protection of 4KV and external 20KV.

The driver should be suitable for an operationg voltage range of

140-270V AC. The driver should be BIS approved, fully potted with

Asphault material and encapsulated with 440V Stress Voltage

protection for 8 Hrs. High Cut off : 325V(+/- 15V) and Auto Restart

function should also be available within the fixture. The luminaire

should comply with all the required IEC and IS standards and

Providing Fitting and Fixing of 35 metre height High Mast Towers.-

279 MR Luminaires.High Mast should be designed to withstand the wind Each 4.00 0.00 2398497.50 0.00 9593990.00

load of 47m/s and the weight of the 24 Nos 940W LED Luminaires,

Feeder Pillar and Control Gear Rack- Supply of IP 54 cubicle type

High mast Lighting Panel suitable for 415 volt, 3 phase, 4 wire 50

HZ AC supply system, fabricated in compartmentalized design from

CRCA steel of 2 mm thick for frame work and covers, 3 mm thick

for gland platees, including cleaning and finishing complete with 7

tank process having extensible type TPN aluminium alloy bus bar of

280 MR high conductivity, with base frame of M.S. section of suitable size, Each 10.00 0.00 89087.05 0.00 890870.50

copper earth bar of size 25mmx 5mm at the rear with 2 nos earth

stud, complete with control wire, cable alleys, cable gland plates,

including following items mentioned below. The panel should be

suitable for Pedestrail mounting type 500mm above ground level

with necessary base frame.

Supply of Oudoor type, Pedestrial type mounting, double door

arrangement MS painted Control Gear racks suitable for mounting

up to 16Nos of 2kW ballasts, capacitors, CT's and terminals with

281 MR complete accessories.Cabinet will have exhast fan/ Lights/ power Each 4.00 0.00 109645.60 0.00 438582.40

point 1-no 5-pin socket . Ms Enclosure will having exhaust fans/

Fluorescent Light fixture for inspection inside cabinet complete as

282 MR Cables

Supply & Installations of following sizes 1.1 KV FR XLPE insulated

cable with copper conductor, PVC inner sheathed, unarmoured,

283 a overall PVC sheathed stranded in conformity to the technical Rmt 300.00 0.00 1507.63 0.00 452288.10

specification and as per latest IS - codes. Need for feeder pillar to

gear box - 25 sqmm x 4 core

Supply & Installations of following sizes 1.1 KV FR XLPE insulated

cable with copper conductor, PVC inner sheathed, unarmoured,

284 b overall PVC sheathed stranded in conformity to the technical Rmt 2800.00 0.00 178.17 0.00 498887.48

specification and as per latest IS - codes. Need for gear box to

luminaires - 4 sqmm x 3 core

Supply & Installations of following sizes 1.1 KV FR XLPE insulated

cable with copper conductor, PVC inner sheathed, unarmoured,

285 c overall PVC sheathed stranded in conformity to the technical Rmt 400.00 0.00 143.91 0.00 57563.94

specification and as per latest IS - codes. Need for earthing - 16

Commissioning-Lux level Measurement & Verification Charges One

Time by Philips/ Equi. engineers

Digitally signed by ANUJ

Technical specification Bleacher

Overall Size: 4.4 Wide x 2.07 Depth x 1.24 Height: 25 seat

MS Square tube 50x2 and standard angle 50x5 de-attachable

framework with cross bracing

Aluminum anodized profile deck 250x38x3 for walk way. All

structure is powder coated or Gl coated. Bleacher is providing with

back railing and side railing.

Seat: Model No.: FI1001 Blow molded HDPE seat having wall

thickness 2-3 mm.Seat Width: 420mm,

Back Height:380mm,

Seat Depth:465mm.

Material: Blow molded, HDPE (high-density polyethylene), Anti UV

288 MR-35 Protection.

TENSILE ROOFING & GALLERY CHAIR

Design – A sample drawing has been given with this tender to guide

the contractor to know the type and nature of work to be executed.

However, tender drawing attached with this document is not the

final drawing adopted for the construction. Before execution of the

work the agency must get the foundation design and design of

289 structural framework with stand 200km/hr) from any structural

consultant and get the same vetted from any Government

Engineering College. The work is to be executed strictly as per the

approved foundation design and structural design duly vetted by

approved authority. All expenses for the above activity shall be

borne by the contractor.

290 MS Steel structure

Structural Steel Work Providing, Fabricating, Assembling, painting,

hoisting, erecting and placing in position MS Built-up

section/Tubular Structure ( MS built-up section :-Rolled section &

plates confirming to IS 2062 minimum required grade E250,Tubular

Structure:- made from Steel hollow sections, ISI marked from SAIL

/ RINL /TATA/JINDAL/APPOLO, conforming to IS 1161/1239/4923,

minimum required Grade YST 240, in the profile shape as per

drawings with special plate connector, pinion joints, Plates, hollow

sections etc. using flame cutting system, SAW/MMAW/MIG welding

process with special plate connectors, pinion joints, plates, hollow

sections to all heights, tools and plants and necessary scaffoldings

etc. required for all operations involved. The structural members

shall be painted with 300 DFT anticorrosive protection coating using

Paint/Primer of approved make with one or two coat of Epoxy

Primer cum MIO 150 microns thick and final coat of polyurethane

paint 100 microns thick (to be applied in 2 coats). Up to all heights

including preparation of the surface by copper slag blasting before

application of primer/paint as per SA2.5 standard. The item shall be

executed as per approved drawings and direction of the Engineer-in-

Charge complete. (Note: The work shall be executed as per

manufacturer’s specifications wherever applicable, relevant code of

practice and sound engineering practice.)

Design – A sample drawing has been given with this tender to guide

the contractor to know the type and nature of work to be executed.

However, tender drawing attached with this document is not the

final drawing adopted for the construction. Before execution of the

work the agency must get the foundation design and design of

292 MR-36 structural framework with stand 200km/hr) from any structural

consultant and get the same vetted from any Government

Engineering College. The work is to be executed strictly as per the

approved foundation design and structural design duly vetted by

approved authority. All expenses for the above activity shall be

borne by the contractor.

293 Tensile fabric structure

Tensile Membrane Fabric Providing, fabricating, assembling and

erection of pre stressed Tensile Membrane Fabric structure in

desired profile as per drawing, with Type III, Mehatop N having a

minimum weight of 1050 g/sqm as per particular specification with

a 20 years warranty etc. (Rate includes cost of fabric , shop

drawings, patterning, forming, cutting, fabrication, hot weld stich of

fabric, over steel frames with all fittings and fixtures such as

Galvanized MS Membrane /End Plate ,Shackles, Rigging Screws ,

Turnbuckles, swedge,fork , keder rods & galvanized MS strands

294 /cables with stainless steel end terminals complete as per Drawing Sqm 1800.00 0.00 5503.00 0.00 9905400.00

/ Detail & as per technical specifications and as per the instructions

of Engineer-in-charge, Transport to the site, assembling and

installation with GI bles,hardware,Alluminium flat, EPDM gasket and

required accessories wherever required complete including lifts up

to all heights, tools and plants, and necessary scaffolding etc.

required for all operations in all respect as per direction of Engineer-

In-Charge). (Note: Actual Surface area of fabric shall only be

measured for payment.)

STADIUM GALLERY CHAIRS

A. The Seat should be attached directly to a corrosion resistant

galvanized pipes by means of four tamper proof bolts and steel

B. The pipe support system has the capability to be fixed to tread or

C. The beam support system is supplied in modular units of varying

lengths as to enable configuration of required row lengths.

D. The seat base and back is ergonomically designed to provide

maximum user comfort.

295 MR-37 E. The seat incorporates a full lower back to eliminate interference Each 1500.00 0.00 7401.00 0.00 11101500.00

from the feet of the people behind.

F. The seat is guaranteed to maintain its original color with

minimal fading for a two year guarantee period.

G. The seat incorporates slot to assist with drainage of water

H. Seat design allows for adjustment of seat centers on site to

compensate for any variance in as built site dimensions and allow

for the reconfiguration of seating without the relocation of fixing

I. A single or two-digit numbering system to be supplied.

297 INTERNAL PLUMBING WORKS

Digitally signed by ANUJ

Providing and fixing white vitreous china pedestal type water closet

(European type W.C. pan) with seat and lid, 10 litre low level white

P.V.C. flushing cistern, including flush pipe, with manually

298 17.2.1 controlled device (handle lever), conforming to IS : 7231, with all Each 23.00 5891.27 135499.14 0.00

fittings and fixtures complete, including cutting and making good

the walls and floors wherever required. W.C. pan with ISI marked

white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.

brass pillar taps, 32 mm C.P. brass waste of standard pattern,

299 17.7.4 including painting of fittings and brackets, cutting and making good Each 20.00 2904.35 58087.00 0.00

the walls wherever require :White Vitreous China Flat back wash

basin size 550x400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china battery based infrared

sensor operated urinal of approx. size 610 x 390 x 370 mm having

pre & post flushing with water (250 ml & 500 ml consumption),

300 17.80 having water inlet from back side, including fixing to wall with Each 24.00 7447.83 178747.96 0.00

suitable brackets all as per manufacturers specification and

direction of Engineer-in-charge.

Providing and fixing stone slab with table rubbed, edges rounded

and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in

urinal partitions by cutting a chase of appropriate width with chase

cutter and embedding the stone in the chase with epoxy grout or

301 8.10.2 with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded Sqm 16.00 3767.11 60273.80 0.00

stone aggregate 6 mm nominal size) as per direction of Engineer-in-

charge and finished smooth. Granite Stone of approved shade

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as

per IS: 13983 with C.I. brackets and stainless steel plug 40 mm,

302 17.10.2.1 including painting of fittings and brackets, cutting and making good Each 2.00 4544.97 9089.94 0.00

the walls wherever required : Kitchen sink without drain board .

610x510 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin

303 17.28.2.1 including P.V.C. waste fittings complete. Flexible pipe ,40 mm dia Each 2.00 110.96 221.91 0.00

Providing and fixing uplasticised PVC connection pipe with brass

unions : 45 cm length , 15 mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior

305 17.31 glass (of approved quality) complete with 6 mm thick hard board Each 41.00 1500.48 61519.51 0.00

ground fixed to wooden cleats with C.P. brass screws and washers

306 17.34.1 Providing and fixing toilet paper holder : C.P. brass Each 36.00 723.89 26060.21 0.00

Providing and fixing PTMT liquid soap container 109 mm wide, 125

mm high and 112 mm distance from wall of standard shape with

307 17.71 bracket of the same materials with snap fittings of approved quality Each 28.00 155.56 4355.70 0.00

and colour, weighing not less than 105 gms.

Providing and fixing CP Brass 32mm size bottle trap of approved

308 17.22A quality & make and as per the direction of engineer in charge. Each 46.00 942.35 43348.08 0.00

Providing and fixing PTMT towel ring trapezoidal shape 215 mm

long, 200 mm wide with minimum distances of 37 mm from wall

309 17.72 face with concealed fittings arrangement of approved quality and Each 29.00 217.66 6312.07 0.00

colour, weighing not less than 88 gms.

Providing and fixing Coat Hook.

Providing ,Fixing of straight / offset type flexible single body push

fit type WC pan connector of with integral single mould sealing fins

311 NON DSR made of flexible EVA body to be fixed with manufacture supplied Each 43.00 0.00 918.00 0.00 39474.00

grease, including rubber bush / adaptor for use with uPVC pipe as

supplied with the pan connector.

Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931 :

Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto

313 17.16a 1meter long with S.S. Triangular plate to european type W.C. Of Each 43.00 318.30 13686.85 0.00

approved quality and make as approved by engineer in charge.

Providing and fixing C.P. brass long body bib cock of approved

314 18.51.1 quality conforming to IS standards and weighing not less than 690 Each 13.00 753.24 9792.14 0.00

gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and

315 18.53.1 geyser points of approved quality conforming to IS:8931 15mm Each 140.00 532.02 74483.10 0.00

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet

: 100 mm diameter

Providing and fixing brass stop cock of approved quality : 15 mm

Providing and fixing PTMT soap Dish Holder having length of

318 18.65 138mm, breadth 102mm, height of 75mm with concealed fitting Each 4.00 102.87 411.50 0.00

arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to

319 17.73 wooden cleats with CP brass screws with concealed fittings

arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide

320 17.73.1 and effective height of 88 mm, weighing not less than 170 gms Each 16.00 609.91 9758.54 0.00

Providing & Fixing of Grab bar 600 mm of non slipping grip as per

321 NON DSR standard specification of use in disabled toilet complete with Each 4.00 0.00 5763.00 0.00 23052.00

brackets suitable for wall installation as per approved sample

complete in all respect.

Supply,Installation, testing and commissioning of Water Heater

complete with heavy gauge hot and cold water flexible pipe

322 NON DSR connections, Nano polymer coated tank, 8 bar pressure ,of Each 4.00 0.00 15128.00 0.00 60512.00

approved make complete with all necessary material as directed by

Engineer - in - Charge. 25-Litre Storage capacity

Providing & Fixing of ISI mark Bath tub with all the accessories of

323 NON DSR complete with all respect approved by Engineer Incharge. Each 2.00 0.00 50776.00 0.00 101552.00

Digitally signed by ANUJ

Providing & Fixing of ISI mark Bath tub spout with all the

324 NON DSR accessories of complete with all respect approved by Engineer Each 2.00 0.00 3780.00 0.00 7560.00

Providing & Fixing of Steam Sauna bath with all the accessories of

complete with all respect Sauna Cabin 8.6x6.11x8 feet consists of

One Side Spruce Wooden Panelling on a Concrete Wall Fully

Insulated withGlass Wool Stacked in Aluminium Foil Supported by

Iron Mesh Wire. SAUNA ACCESSORIES : Bulb,Sauna Prevention

325 NON DSR Lamp ,Hover Glass –Sand Meter for Sauna Room ,Wooden Bucket Each 2.00 0.00 885367.00 0.00 1770734.00

with Ladle. ,Sauna Temperature MeterMale15 Kw - Sauna Heater .

Digital Steam Control Panel with Timer and Temperature Setting. IP

65 for water proof, splash proof & dust proofapproved by Engineer

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps

326 18.8 at 1.00 m spacing. This includes jointing of pipes & fittings with one

step CPVC solvent cement and the cost of cutting chases and

making good the same including testing of joints complete as per

direction of Engineer in Charge.

Concealed work, including cutting chases and making good the

40 mm nominal bore

50 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with

334 18.7 clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints complete

as per direction of Engineer in Charge.

335 Internal work - Exposed on wall

336 18.7.1 15mm nominal bore Mtr. 272.10

Providing and fixing Forged Brass Ball Valve (Screwed). with setting

342 NON DSR and gland of superior quality having minimum working pressure of

343 15 mm nominal bore Each 702.00

Supplying, fixing, testing and commissioning of butterfly valve of

PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete

348 18.11.2 with nuts, bolts, washers, gaskets conforming to IS 13095 of Each 17.00 4023.53 68399.96 0.00

following sizes as required : 50mm dia.

Providing and fixing PTMT Ball cock of approved quality, colour and

349 18.62 make complete with Epoxy coated aluminium rod with L.P./

H.P.H.D. plastic ball.

25 mm nominal bore, 152mm long, weighing not less

40 mm nominal bore, 206mm long, weighing not less than 690

50 mm nominal bore, 242mm long, weighing not less than 1240

Providing and placing on terrace (at all floor levels) polyethylene

water storage tank, ISI : 12701 marked, with cover and suitable

353 18.48 locking arrangement and making necessary holes for inlet, outlet per litre 14000.00 10.31 144396.14 0.00

and overflow pipes but without fittings and the base support for

Providing & fixing Auto Air vent for cold water supply risers,

suitable for pressure not less than 15 Kg/Sq.cm. 15mm

Providing, fixing & testing uPVC SWR pipes confirming to IS 13592

(Type B) alongwith all required fittings like tees, bends, crosses

with or without access doors jointed with approved solvent cement

355 NON DSR as per manufacturer's recommendations, fixed to walls and ceilings

with clamps complete including cutting and making good the floors

and walls where required complete of outer diameter.

Providing, fixing, jointing and testing in position the following uPVC

pipes conforming to IS 4985 of 6 kg/sqcm pressure rating including

all fittings, solvent weld joints, testing complete for drainage

357 NON DSR system cut to required length to be laid under floor including

covering all around with cement concrete and making good the

same complete as required.

358 For waste pipes

Providing and Fixing 110x110 mm uPVC 'P' trap with Height

riser/Saddle as required size ftting with seal 50 mm of self

362 NON DSR cleansing design floor/urinal trap without vent suspended with

supporting clamp or in sunken portion including cutting and making

good the walls and floors wherever required complete in all

Providing and Fixing uPVC floor drain of following size inlet and

364 NON DSR outlet including cutting and making good the walls and floors

wherever required complete in all respects.

Digitally signed by ANUJ

Providing and fixing 125 mm dia, 3 mm thick Stainless steel

366 NON DSR grating with frame for floor traps or drains of required pattern

including cutting and making good the floors complete.

Providing & fixing PVC clean out plug with suitable insert keys for

368 NON DSR opening in: brass cap, male threaded joint with threaded uPVC

socket fixed to uPVC pipe joints as required complete in all

Providing and fixing on wall face unplasticised Rigid PVC rain water

370 12.41 pipes conforming to IS : 13592 Type A, including jointing with seal

ring conforming to IS : 5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

372 12.41.1 90 mm diameter Mtr 226.48

Providing and fixing on wall face unplasticised - PVC moulded

fittings/ accessories for unplasticised Rigid PVC rain water pipes

373 12.42 conforming to IS : 13592 Type A including jointing with seal ring

conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

374 12.42.2 Single Push fit coupler

376 12.42.3 Single Tee with door

380 12.42.6 Shoe (Plain)

Providing and fixing to the inlet mouth of rain water pipe cast iron

382 12.44 grating 15 cm diameter and weighing not less than 440 grams. Each 10.00 50.93 509.32 0.00

Providing and fixing unplasticised -PVC pipe clips of approved

design to unplasticised - PVC rain water pipes by means of

383 12.43 50x50x50 mm hard wood plugs, screwed with M.S. screws of

required length, including cutting brick work and fixing in cement

mortar 1:4 (1 cement : 4 coarse sand) and making good the wall

Making khurras 45x45 cm with average minimum thickness of 5 cm

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x

385 12.22 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 Each 10.00 283.48 2834.76 0.00

coarse sand) and a coat of neat cement, rounding the edges and

making and finishing the outlet complete.

Providing and fixing G.I. pipes complete with G.I. fittings including

trenching and refilling etc.

387 External Work

Painting G.I. pipes and fittings with two coats of anti-corrosive

bitumastic paint of approved quality :

392 18.40.3 25 mm nominal dia Pipes Metre 35.00 16.22 567.54 0.00

Providing and filling sand of grading zone V or coarser grade

alround the GI pipes in external work.

Making connection of G.I. distribution branch with G.I. main of

399 18.13 following sizes by providing and fixing tee, including cutting and

threading the pipe etc. complete :

Excavating trenches of required width for pipes, cables, etc

including excavation for sockets, anddressing of sides, ramming of

bottoms, depth up to 1.5 m, including getting out the excavated

402 2.10 soil, and then returning the soil as required, in layers not exceeding

20 cm in depth, including consolidatingeach deposited layer by

ramming, watering, etc. and disposing of surplus excavated soil as

directed,within a lead of 50 m :

403 2.10.1 All kinds of soil

Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm

Earth work in excavation by mechanical means (Hydraulic

excavator) /manual means in foundation trenches or drains (not

exceeding 1.5 m in width or 10 Sqm on plan), including dressing of

405 2.8 sides and ramming of bottoms, lift upto 1.5 m, including getting out

the excavated soil and disposal of surplus excavated soil as

directed, within a lead of 50 m.

Supplying and laying of following size DWC SN8 pipe ISI marked

along with all accessories like socket, bend, couplers etc.

conforming to IS 16098, Part II complete with fitting and

407 NON DSR cutting,jointing etc.direct in ground (75 cm below ground level)

including excavation and refilling the trench but excluding sand

cushioning and protective covering etc., complete as required.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse

409 19.2 sand : 10 graded stone aggregate 40 mm nominal size) all-round

S.W. pipes including bed concrete as per standard design :

Providing and fixing square-mouth S.W. gully trap class SP-1

complete with C.I. grating brick masonry chamber with water tight

C.I. cover with frame of 300x300 mm size (inside) the weight of

411 19.4.1.1 cover to be not less than 4.50 kg and frame to be not less than Each 13.00 2608.86 33915.18 0.00

2.70 kg as per standard design: 100x100 mm size P type. With

common burnt clay F.P.S. (non modular) bricks of class designation

Digitally signed by ANUJ

Providing and laying non-pressure NP2 class (light duty) R.C.C.

412 19.6 pipes with collars jointed with stiff mixture of cement mortar in the

proportion of 1:2 (1 cement : 2 fine sand) including testing of joints

etc. complete :

413 For storm water pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse

sand : 10 graded stone aggregate 40 mm nominal size) up to

415 19.3 haunches of RCC. pipes including bed concrete as per standard

Constructing brick masonry manhole in cement mortar 1:4 ( 1

cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal

size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8

graded stone aggregate 40 mm nominal size), inside plastering 12

417 19.7 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand)

finished with floating coat of neat cement and making channels in

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) finished with a floating coat of neat

cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with

frame (light duty) 455x610 mm internal dimensions,total weight of

cover and frame to be not less than 38 kg (weight of cover 23 kg

and weight of frame 15 kg) :

With common burnt clay F.P.S.(non modular) bricks of class

Extra for depth for manholes: Size 90x80x90 cm

With common burnt clay F.P.S.(non modular) bricks of class

Constructing Brick Masonry circular type manhole 0.91 m internal

dia at bottom and 0.56m dia at top with FPS bricks class

designation 75 in cement mortar 1:4 (1 cement : 4 Coarse sand),

inside cement plaster 12mm thick with cement mortar 1:3 ( 1

cement : 3 coarse sand) finished with a floating coat of of neat

422 19.9 cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand

: 6 graded stone aggregate 40mm nominal size) and making

necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2

Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size)

finished with a floating coat of neat cement complete as per

standard design.

0.91m deep with SFRC cover and frame (heavy duty HD-20 grade

designation) 560mm internal diameter conforming to I.S:12592,

total weight of cover and frame to be not less than 182Kg. fixed in

423 19.9.1 cement concrete 1:2:4 mix (1cement: 2 coarse sand: 4 graded

stone aggregate 20mm nominal size) including centering,

shuttering all complete.(Excavation foot rests and 12mm thick

cement plaster at the external surface shall be paid for separately)

with common burnt clay F.P.S.(non module) brick of class

designation 7.5

Extra depth for circuler type manholes 0.91 m internal dia ( at

bottom ) beyond 0.91m to 1.67 m .

with common burnt clay F.P.S.(non module) brick of class

designation 7.5

12 mm cement plaster finished with a floating coat of neat cement

Providing orange colour safety foot rest of minimum 6 mm thick

plastic encapsulated as per IS : 10910, on 12 mm dia steel bar

conforming to IS: 1786, having minimum cross section as 23

mmx25 mm and over all minimum length 263 mm and width as

165 mm with minimum 112 mm space between protruded legs

having 2 mm tread on top surface by ribbing or chequering besides

necessary and adequate anchoring projections on tail length on 138

mm as per standard drawing and suitable to with stand the bend

test and chemical resistance test as per specifications and having

manufacture's permanent identification mark to be visible even

after fixing, including fixing in manholes with 30x20x15 cm cement

concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone

aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry road gully chamber 45x45x77.5 cm

430 19.28 with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with

precast R.C.C. vertical grating complete as per standard design :

with common burnt clay F.P.S.(non module) brick of class

designation 7.5

Construction of brick masonry Grease Trap of Effective depth for

Kitchen drainage with precast concrete block in cement mortar 1:4

(1 cement : 4 coarse sand) , foundation concrete 1:4:8 mix (1

cement : 4 coarse sand; 8 graded stone aggregate 40mm nominal

size), inside and outside plastering 12mm thick with cement mortar

432 1:3 (1 cement : 3 coarse sand), finished with a floating coat of

neat cement inside and rough plaster on outside, including fixing of

grating , neatly finished with 1 nos.manhole cover complete in all

respects including necessary excavation, refilling and disposal of

surplus earth, complete as per attached Sketch .

Digitally signed by ANUJ

Making connection of drain or sewer line with existing manhole

including breaking into and making good the walls, floors with

cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

434 19.21 stone aggregate 20 mm nominal size) cement plastered on both

sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished

with a floating coat of neat cement and making necessary channels

for the drain etc. complete :

437 INTERNAL ELECTRICAL WORK

Wiring for light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FRLS PVC insulated copper conductor single core

cable in surface / recessed medium class PVC conduit, with modular

438 1.10.3 switch, modular plate, suitable GI box and earthing the point with Point 722.00 1559.86 1126219.71 0.00

1.5 sq.mm FRLS PVC insulated copper conductor single core cable

etc. as required. Group C

Wiring for group controlled (looped) light point/fan point/exhaust

fan point/ call bell point (without independent switch etc.) with 1.5

sq. mm FRLS PVC insulated copper conductor single core cable in

439 1.55.3 surface/ recessed PVC conduit, and earthing the point with 1.5 sq. Point 794.00 912.31 724375.25 0.00

mm FRLS PVC insulated copper conductor single core cable etc. as

required. Group C

Wiring for circuit/ submain wiring alongwith earth wire with the

440 1.14 following sizes of FRLS PVC insulated copper conductor, single core

cable in surface/ recessed medium class PVC conduit as required.

Supplying and drawing following sizes of FRLS PVC insulated copper

452 1.17.12 conductor, single core cable in the existing surface/ recessed steel/ meter 28800.00 145.67 4195356.48 0.00

PVC conduit as required. 3 x 2.5 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit

453 1.21 along with accessories in surface/recess including cutting the wall

and making good the same in case of recessed conduit as required.

Supplying and fixing metal box of following sizes (nominal size) on

457 1.22 surface or in recess with suitable size of phenolic laminated sheet

cover in front including painting etc. as required.

Supplying and fixing modular blanking plate on the existing

462 1.26 modular plate & switch box excluding modular plate as required. Each 160.00 42.53 6805.12 0.00

Supplying and fixing suitable size GI box with modular plate and

463 1.31 cover in front on surface or in recess, including providing and fixing Each 92.00 507.19 46661.86 0.00

3 pin 5/6 A modular socket outlet and 5/6 A modular switch,

connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and fixing

464 1.32 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular Each 294.00 623.09 183189.58 0.00

switch, connections etc. as required.

Supplying and fixing two module stepped type electronic fan

465 1.25 regulator on the existing modular plate switch box including Each 134.00 392.36 52575.93 0.00

connections but excluding modular plate etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction

466 1.33 box/ wooden block including connections etc. as required. Each 64.00 92.51 5920.45 0.00

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providng and fixing

467 1.56 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/6 A modular Each 200.00 718.79 143758.16 0.00

switch, connections etc. as required. (For light plugs to be used in

non residential buildings).

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

468 1.19 copper conductor PE insulated, shielded with fine tinned copper Meter 616.00 49.98 30784.66 0.00

braid and protected with PVC sheath in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing following modular switch/ socket on the

469 1.24 existing modular plate & switch box including connections but

excluding modular plate etc. as required.

470 1.24.6 Telephone socket outlet Each 46.00 157.37 7238.95 0.00

471 1.24.7 TV antenna socket outlet Each 36.00 157.37 5665.26 0.00

472 MR Data socket outlet RJ-6 Each 58.00 265.83 15417.85 0.00

Supplying and fixing following size/ modules, GI box alongwith

473 1.27.1 modular base & cover plate for modular switches in recess etc. as Each 140.00 316.86 44360.88 0.00

required. 1 or 2 Module (75 mmX75 mm)

Supplying and fixing following Modular base & cover plate on

474 1.28.1 existing modular metal boxes etc. as required. 1 or 2 Module Each 140.00 141.42 19798.65 0.00

Digitally signed by ANUJ

Supply and fixing of following Floor boxes for screed floor having

following accessaries as follows: Full backbox for screed floor 3

compartments ( 325 x 325 mm ). Accepts PVC and metal screed

floor ducting and conduits with 20mm dia and 25 mm dia. Auto

adjustable to screed height 65 to 90 mm with Lid & trim for 3

475 MR compartment floor box Grey cover RAL 7031 with flexible cable Set 4.00 0.00 9000.00 0.00 36000.00

exits (Size 265 mm x 265 mm) for carpet/tile, flush mounting,

Blank plates for floor box to cover of an unused compartment Flat

support plate 6 + 6 module for light plug or power plug point of

approved make and waved support plates for 4 modules IT points

(2 + 2 modules).

Supplying and fixing following way, single pole and neutral, sheet

steel, MCB distribution board, 240 V, on surface/ recess, complete

476 2.3 with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole and

neutral, sheet steel, MCB distribution board, 415 V, on surface/

479 2.4 recess, complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including earthing

etc. as required. (But without MCB/RCCB/ Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C”

curve, miniature circuit breaker suitable for inductive load of

483 2.10 following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing MCB

DB complete etc. as required.

Supplying and fixing 40 A to 63 A rating, 240/415 V, 10 kA, “C”

curve, miniature circuit breaker suitable for inductive load of

487 MR following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase

and neutral), 240 V, residual current circuit breaker (RCCB), having

490 2.14 a sensitivity current 30 mA in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 V, residual

current breaker with over current protection (RCBO), having a

493 MR sensitivity current 100 mA in the Sheet Steel Enclosure complete Each 2.00 0.00 8250.00 0.00 16500.00

with connections, testing and commissioning etc. as required.(For

Supplying and fixing following rating, four pole, 415 V, residual

current breaker with over current protection (RCBO), having a

494 MR sensitivity current 300 mA in the Outdoor type (IP:65) Polystyrene Each 18.00 0.00 8500.00 0.00 153000.00

Circuit Breaker Boxes complete with connections, testing and

commissioning etc. as required.(For AC Outdoor)

Supplying and fixing Cable End Box (Loose wire box)(IP 43)

495 2.23 suitable for following single pole and neutral, sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with testing

and commissioning etc. as required.

496 2.23.4 For 14 way, Double door SPN MCBDB Each 20.00 959.10 19181.93 0.00

497 2.23.2 For 8 way, Double door SPN MCBDB Each 8.00 884.67 7077.32 0.00

Supplying and fixing Cable End Box (Loose wire box)(IP 43)

498 2.24 suitable for following triple pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess, complete with testing

and commissioning etc. as required.

499 2.24.2 For 6 way, Double door TPN MCBDB Each 6.00 1195.15 7170.90 0.00

500 2.24.3 For 8 way, Double door TPN MCBDB Each 14.00 1424.82 19947.51 0.00

501 MR For 12 way, Double door TPN MCBDB Each 6.00 2883.67 17302.02 0.00

Supply and fixing of Vertical Air Termination Solid Aluminium with

base- 16 mm dia and 1000 mm long. Air Terminal Base should be

502 MR tested for conditioning, Ageing Test & Lightning impulse current Nos. 30.00 0.00 1315.00 0.00 39450.00

withstand test: 100 kA of 10/350μs waveform in an accredited

Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017

Supply and fixing of 8 mm dia solid Aluminium Conductor tested as

503 MR per IEC 62561- 2 conducted in the Govt. aggregated thirty party RM 1600.00 0.00 90.00 0.00 144000.00

laboratory to meet the requirement of IS/ IEC 62305;

Supply and fixing of Polyamide Holder for fixing 8mm dia Conductor

Supply and fixing of Expansion Piece without connector to

compensate the expansion and contraction of Solid Round Al.

505 MR Conductor during temperature variations to be provided on Nos. 80.00 0.00 150.00 0.00 12000.00

conductors length over 20 meters to connect Solid Round Al.

Conductor at both ends to meet the requirements of IS/IEC

Supply and fixing of Al. Straight Splicers for 8mm and 10 mm

Conductor to meet the requirement of IS IEC 62305 tested for

506 MR conditioning, Ageing Test & Lightning impulse current withstand Nos. 70.00 0.00 200.00 0.00 14000.00

test: 100 kA of 10/350μs waveform in an accredited Third party

laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol;

Supply and fixing of Cross splicer should be ttested for conditioning,

Ageing Test & Lightning impulse current withstand test: 100kA of

507 MR 10/350μs waveform in an accredited Third party laboratory as per Nos. 90.00 0.00 250.00 0.00 22500.00

6.3 & 6.4 of IEC 62561-1 2017 protocol;

Digitally signed by ANUJ

Supply and fixing of Al. Straight Splicers for 8mm and 10 mm

Conductor to meet the requirement of IS IEC 62305 tested for

508 MR conditioning, Ageing Test & Lightning impulse current withstand Nos. 40.00 0.00 200.00 0.00 8000.00

test: 100 kA of 10/350μs waveform in an accredited Third party

laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol;

Supply and fixing of 8 mm dia solid Aluminium Conductor tested as

509 MR per IEC 62561- 2 conducted in the Govt. aggregated thirty party RM 1500.00 0.00 90.00 0.00 135000.00

laboratory to meet the requirement of IS/ IEC 62305;

Supply and fixing of Polyamide Holder for fixing 8mm dia Conductor

Supply and fixing of Each down-conductor should be provided with

511 MR a test link in order to disconnect the earth termination system for Nos. 30.00 0.00 375.00 0.00 11250.00

enabling measurements. SS Test Link To connect Round to Flat

Supply and fixing of 25 X 6 mm GI strip from AL Conductor to the

earth pit station and further the same strip shall be used for

512 MR interconnecting all the earth pits below ground leve Zinc coating: RM 1300.00 0.00 263.00 0.00 341900.00

500 g/m square (Approx :70 micron coating) Should be tested and

use exclusively for lightning protection ,earthing system and ring

equipotential bonding.

Supply and fixing of Holder -GI for fixing 25 x 6 mm GI Strip;

Supply and fixing of Earth Electrode Cu Bonded Steel Rod 14.2mm

dia x 3000mm (250Microns);Eco Friendly rust proof heavy duty

weather proof Polyethylene Earth Pit Chamber with following

514 MR dimensions :254 mm dia (top), 330 mm dia (bottom) & 260 mm Nos. 24.00 0.00 7020.00 0.00 168480.00

(height). ;14.2 / OD SS Clamp Both Side;Jef Eco Safe carbon based

backfill compound - 50 Pounds;

Providing & fixing in position 1000 mm wide , Electrical Insulating

Mats as per IS 15652:2006, 2mm thick, suitable upto 3.3 KV , fire

515 MR retardant, no effect of acids, alkalies and transformer oils, moisture RM 20.00 0.00 1250.00 0.00 25000.00

proof, high tensile strength and texture finish / cloth impression

(Anti slip , marking on top) .

Providing and fixing M.V. danger notice plate of 200 mm X 150

516 2.21 mm, made of mild steel, at least 2 mm thick, and vitreous Nos. 10.00 286.03 2860.28 0.00

enameled white on both sides, and with inscription in single red

colour on front side as required.

Supply and fixing of Shock treatment chart duly mounted on a

517 MR wooden frame with glass on, as required in 2 languages (Hindi & Each 2.00 0.00 350.00 0.00 700.00

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with cover

518 5.4 plate having locking arrangement and watering pipe of 2.7 Meter Set 28.00 7944.98 222459.37 0.00

long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

519 5.11 pipe from earth electrode including connection with G.I. nut, bolt, Meter 300.00 750.69 225206.94 0.00

spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Excavation for earthing Pit in soft soil, depth upto 3.6 m including

MR/ REFER dressing of sides lift up as required, including getting out the

521 excavated soil, refilling with sand and or good soil after laying of cum 68.00 0.00 654.00 0.00 44472.00

earthing pit material etc, ramming, watering and disposal of surplus

excavated soil as directed.

Supplying and laying of following size DWC HDPE pipe ISI marked

along with all accessories like socket, bend, couplers etc.

conforming to IS 14930, Part II complete with fitting and cutting,

522 14.16.1 jointing etc..direct in ground (75 cm below ground level) including Meter 700.00 262.64 183844.57 0.00

excavation and refilling the trench but excluding sand cushioning

and protective covering etc., complete as required. 63 mm dia (OD-

63 mm & ID-51 mm nominal)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for

loop earthing as required.

Design, Manufacture, Supplying, Transport to the site, Receiving,

Unloading, Shifting to Sub-Station at various locations, handling,

assembling, installation in correct aligned position, grouting with

dash fasteners, GI nuts-bolts, testing and commissioning of the

following bolted fabricated in compartmentalized (Form-3B

construction) conform to IS: 8623/1993, Suitable for 415V,

3Phase, 4 Wire 50 Hz Ac supply, are housed in design from CRCA

sheet steel of 2mm thick for frame work and door covers, 3mm

thick for gland plate, i/c cleaning & finishing complete, having

524 extensible type bus bars of high conductivity, SMC bus bar

supports, the maunfacturer shall be certified from CPRI for short

circuit withstand capacity of min. 70kA for 1 Sec., fabrication shall

be done in transportable sections and all front and back doors shall

be hinged type and earth with frame, Entire panel shall have a

common earth bar as specified below at the rear with 2 Nos. earth

stud each side, bus bars and control wiring with suitable size of

FRLS PVC insulated copper conductor cable, cable alleys, cable

gland plates in two half, i/c providing following switch gears :-

The Bus bars will be Copper purity 99.9% / electrolytic grade E91

Aluminium duly sleeved with Helogen Free heat shrink coloured

Insulated tube confirming to IEC 60684-3-247 Standard. The

525 powder coating (70-80micron as per IS:13871 for indoor and 100-

120 micron for outdoor), include one size higher terminal block in

cable alley and interconnecting wires between bus bars and

terminals via MCB.

General Notes for site visit report for Panels before submitting GA.

The Manufacturer must visit the site before submitting GA drawings

and submit a report consisting following:

528 Possible height for Panel.

529 Possible width for Panel

530 Back access will be possible or not.

531 Cable entry will be from top or bottom.

532 If entry from bottom whether MS. Stand is required or not.

If the panel is wall mounted whether the wall is available or not.

Digitally signed by ANUJ

Path for movement of transportation of panel is possible or not i.e

534 length, width etc. and the transportation sections shall be designed

Sufficient space available at front & back after door opening.

536 Sufficient height available above panel for cable drop.

537 Actual floor to floor height for rising mains.

Also, refer to General Notes and Specifications for Panels/ Boards.

539 All Panels shall be considered Indoor type unless specified.

The degree of protection for all indoor type panels shall be of IP:52

("5" Indicates Dust Protected limited ingress of dust permitted. Will

not interefere with operation of the equipment and "2" indicates

protection against vertically falling drops of water with enclosure

540 tilted upto 15 deg from vertical.) and all outdoor type panels shall

be of IP:55 ("5" indicates Dust Protected limited ingress of dust

permitted. Will not interefere with operation of the equipment and

"5" indicates protection against jets of water)

Provide thermostat controlled panel mounted heavy duty exhaust

541 fan in each Vertical for all Main L.T Panel and Capacitor Panels. For

all other panels a proper ventilation louvers shall be provided.

Fully automtic control thermotate with strip heater shall be provide

542 in each Bus-Bar alley and relay compartments to control the

Contractor to submit manufacturer's selection charts from

approved list of make along with each component part number,

543 Discrimination check certificate throughout the HV/MV network,

insulation material & corners cover on bus-bars for approval.

Contractor shall submit a set of handing over document consisting

operational and maintenance manuals, installation guidelines of all

product's along with data sheets come with product, GA drawings

544 with wiring diagram and product part code etc. shall be arranged

and also place a laminated copy in a pocket inside the respective

If mentioned fault rating of bus-bar and circuit breaker is

unavailable consider next available upside rating

546 Mimic diagram shall be provided on all panels.

It is recommonded that only one make of switchgear to be used in

a board / Panel.

All live accessible parts shall be shrouded and all equipment shall

be finger touch proof. SMC shrouds busbar supports shall be used.

548 Padlocking facility shall be provided on all MCCB feeders doors and

switch handles shall be locakble in OFF position.

Equipments will be offered for following routine test only:- i). Check

of Bill of Materials as per approved drawing, ii). Visual and

549 Dimensional Check, iii) Functional Check, iv) HV/Megger test as per

relevant IS, v) Busbar Density and Conductivity test, vi) Powder

Coating thickness test

Third Party test report as required by the consultant/ Client/ PMC

550 from the one of the selected vendors from approved list of make for

IP rating, IS/ IEC Compliance and CPRI Compliance tests etc.

Minimum/Maximum Operating height- 300/1800 respectively

Sealing Arrangement:- PE Foam Rubber/ Neoprene Rubber Gasket

Bus Bars Supports - Non-Hygroscopic, Non Carbonising, Corrosinn

Resistant, SMC Supports

1 Set of connector (Phase+Neutral) shall be provided in cable alley

554 for all outgoing with interconnection wires between MCB and

All electrical panel shall have two nos. common G.I. earth bar of

50X6mm for the panels having incomer fault of 50kA and rest all

555 with 32X6mm or as specified conductor throughout of the panel

lenght as per the fault kA rating of main Incomer, at the rear and

for wall mounted panel with 2Nos. earth stud at top one at each

Bottom base channel of MS section not less than 100mmx

556 50mmx50mmx 5mm thick for Main L.T. Panel and capacitor panels

and 40mmx25mmx25mmx 5mm thickplates for all floor mounted

MDB/MCC and SDBs etc.

All outdoor use panel shall have bottom base stand of minimum

557 600mm or as mentioned below with M.S. angle iron 32mmx

32mmx6mm with fixing arrangement in RCC foundation.

No derating shall be applicable upto ambient temp. 50ºC for all

breakers and selected components.

Each door other than bus bar section shall be 2 numbers wing knob

559 cabinet cam lock with master key lock made of zinc alloy powder

coated housing, handle and chrome plated cylinder and nut CL001.

Minimum Air Clearances between bus bars; (Calculation with

560 required supporting document shall be submitted by Panel

manufecturer along with GA diagram).

561 P-P=32mm, P-N=32mm,P-E=26mm and N-E=26mm

Panel Power and control Wiring all FRLS PVC insulated min.

conductor to be used as follows:

563 AC voltage circuit-1.5 sqmm Red,Yellow,Blue &Black

564 Current circuit-1.5 sqmm Red,Yellow,Blue &Black

AC Control circuit-1.5 sqmm White for Phase & Black for Neutral

566 DC Control circuit-2.5 sqmm Grey

567 Power circuit- Red,Yellow,Blue for Phase &Black for Neutral

568 Phase-Neutral Terminology:

569 TP: Three Phase

TPN: Three Phase and Neutral (Neutral shall be Half of Phase

TP+2N: Three Phase and Neutral (Neutral shall be 200% of Phase

4P: Three Phase and Neutral (Neutral shall be 100% of Phase

Labelling- Computerised Laminated Aluminium Name Plate with

573 White letters on Blue/Black Background For Each Feeder and Panel

Digitally signed by ANUJ

The treatment of Panel Shall be Fully automatic 9-tank process for

metal treatment which consists of Solvent/ Alkaline Degreasing,

574 Water Rinsing, De- Rusting, Water Rinsing, Passivation,

Phosphating, Water Rinsing, Activation and Drying

A separate compartment for Minimum 20% spare space of Panel

575 shall be provided for outgoings in future and busbars shall be drilled

During inspection of the panel, the manufacturer of major products

576 shall be available at factory to validitate that the used products are

original. Certification shall be given by OEM's on their company

All incoming/outgoing MCB shall be mounted on din channel inside

577 closed chambers shall have Acrylic sheet infront and front door

should be a glass for see thru.

In Meter boards all copper flexible wiring shall be provied with

578 suitable copper lugs and ferruling at both ends and earthing shall

be provided for individual meter with 2.5sqmm green insulated

Earthing of rising main mounted meter boards shall be connected

579 with rising main earth bar by 2Nos. 20x3 mm GI strips.

1 Nos. 630A TP+NL MCCB built in microprocessor based release

(adjustable O/L,S/C&E/F) of fault breaking capacity 35KA

582 (Ics=Icu=100%) upto 415V manually operated with extended

rotary handle with castle lock for door interlock with Phase

spreader & Phase Barriers at both sides. MCCB shall conforming to

IS-1397-2 1993 as amended.

583 METERING, INDICATOR AND RELAYs

Provide 3 Nos. Resin cast CTs, Class-1.0 and MFM True RMS type

digital with min. features of measurements covering A,V,Hz, PF,

584 kW,VAr,VA, kVA, kVAR, kWH, kVAH, kVARH,MDI, Harmonics,Run

Hours, RS-485 Port, LCD display with class-0.5 accuracy for all

incomer feeder.

1Set of R,Y,B phase indication lamps with control MCB as per fault

requirement with each incomer

586 BUSBAR & TVSS

700Amps TP+50%NL, 25kA, 500volts grade busbar chamber of

suitable length with Aluminium busbars mount on SMC supports. All

interconnections shall be as follows; a). Upto 63A, FRLS PVC

insulated copper flexible colour coded wires b). 64Amp to 200Amp

587 Copper Bus-bars and c). 201Amp and above Aluminium Bus-bars ,

current density of bus-bars shall not be less than 1Amps/sq.mm for

Aluminium and 2Amps/sq.mm for copper cross sectional area of

1 No Surge protection device Type 2 ( Class C), 4 Mode, MOV type

suitable for 8/ 20µs surge,Voltage Protection level Up < 1.8kV,

Operating Temperature -40 deg 'c' - +80 deg 'C', Connected

Between 3Nos. phase to neutral and 1Nos. neutral to earth with

discharge Current Imax. ≥ 40KA Per mode & In ≥ 20kA per Mode.

Make & Model: Argos-AG-230-40T2-E or eq. SPD with 63A 4P HRC

fuses of 100kA breaking capacity. For connecting SPD minimum

10sqmm copper wire must be used & length of connecting leads

shall not be more than 500mm for per mode connection with each

busbar including all necessary accessories. The SPD shall

complience with IEC 61643-11 and certified by

TUV,CE,ROHS,UL94V-O..

5 Nos. 160A 4P MCCB built in thermal magnetic based release

(adjustable O/L & fixed S/C) of fault breaking capacity 25KA

(Ics=Icu=100%) upto 415V manually operated with extended

590 rotary handle with castle lock for door interlock with Phase

spreader & Phase Barriers at both sides. MCCB shall conforming to

IS-1397-2 1993 as amended

1 Nos. 250A 4P MCCB built in thermal magnetic based release

(adjustable O/L & fixed S/C) of fault breaking capacity 25KA

(Ics=Icu=100%) upto 415V manually operated with extended

591 rotary handle with castle lock for door interlock with Phase

spreader & Phase Barriers at both sides. MCCB shall conforming to

IS-1397-2 1993 as amended

1 Nos. 160A 4P MCCB built in thermal magnetic based release

(adjustable O/L & fixed S/C) of fault breaking capacity 25KA

(Ics=Icu=100%) upto 415V manually operated with extended

592 rotary handle with castle lock for door interlock with Phase

spreader & Phase Barriers at both sides. MCCB shall conforming to

IS-1397-2 1993 as amended

3 Nos. 100A 4P MCCB built in thermal magnetic based release

(adjustable O/L & fixed S/C) of fault breaking capacity 25KA

(Ics=Icu=100%) upto 415V manually operated with extended

593 rotary handle with castle lock for door interlock with Phase

spreader & Phase Barriers at both sides. MCCB shall conforming to

IS-1397-2 1993 as amended

5 Nos. 40A, 4P 'C' Curve 10kA MCB with central overload trip

mechanism and flag indication

4 Nos. 63A, 4P 'C' Curve 10kA MCB with central overload trip

mechanism and flag indication

3 Nos. 63A, DP 'C' Curve 10kA MCB with central overload trip

mechanism and flag indication

1 Nos. 250A TP+NL MCCB built in microprocessor based release

(adjustable O/L,S/C&E/F) of fault breaking capacity 35KA

599 (Ics=Icu=100%) upto 415V manually operated with extended

rotary handle with castle lock for door interlock with Phase

spreader & Phase Barriers at both sides. MCCB shall conforming to

IS-1397-2 1993 as amended.

600 METERING, INDICATOR AND RELAYs

Provide 3 Nos. Resin cast CTs, Class-1.0 and MFM True RMS type

digital with min. features of measurements covering A,V,Hz, PF,

601 kW,VAr,VA, kVA, kVAR, kWH, kVAH, kVARH,MDI, Harmonics,Run

Hours, RS-485 Port, LCD display with class-0.5 accuracy for all

incomer feeder.

Digitally signed by ANUJ

1Set of R,Y,B phase indication lamps with control MCB as per fault

requirement with each incomer

603 BUSBAR & TVSS

300Amps TP+50%NL, 25kA, 500volts grade busbar chamber of

suitable length with Aluminium busbars mount on SMC supports. All

interconnections shall be as follows; a). Upto 63A, FRLS PVC

insulated copper flexible colour coded wires b). 64Amp to 200Amp

604 Copper Bus-bars and c). 201Amp and above Aluminium Bus-bars ,

current density of bus-bars shall not be less than 1Amps/sq.mm for

Aluminium and 2Amps/sq.mm for copper cross sectional area of

1 No Surge protection device Type 2 ( Class C), 4 Mode, MOV type

suitable for 8/ 20µs surge,Voltage Protection level Up < 1.8kV,

Operating Temperature -40 deg 'c' - +80 deg 'C', Connected

Between 3Nos. phase to neutral and 1Nos. neutral to earth with

discharge Current Imax. ≥ 40KA Per mode & In ≥ 20kA per Mode.

Make & Model: Argos-AG-230-40T2-E or eq. SPD with 63A 4P HRC

fuses of 100kA breaking capacity. For connecting SPD minimum

10sqmm copper wire must be used & length of connecting leads

shall not be more than 500mm for per mode connection with each

busbar including all necessary accessories. The SPD shall

complience with IEC 61643-11 and certified by

TUV,CE,ROHS,UL94V-O..

2 Nos. 100A 4P MCCB built in thermal magnetic based release

(adjustable O/L & fixed S/C) of fault breaking capacity 25KA

(Ics=Icu=100%) upto 415V manually operated with extended

607 rotary handle with castle lock for door interlock with Phase

spreader & Phase Barriers at both sides. MCCB shall conforming to

IS-1397-2 1993 as amended

12 Nos. 63A, 4P 'C' Curve 10kA MCB with central overload trip

mechanism and flag indication

1 Nos. 100A TP+NL MCCB built in microprocessor based release

(adjustable O/L,S/C&E/F) of fault breaking capacity 35KA

611 (Ics=Icu=100%) upto 415V manually operated with extended

rotary handle with castle lock for door interlock with Phase

spreader & Phase Barriers at both sides. MCCB shall conforming to

IS-1397-2 1993 as amended.

612 METERING, INDICATOR AND RELAYs

Provide 3 Nos. Resin cast CTs, Class-1.0 and MFM True RMS type

digital with min. features of measurements covering A,V,Hz, PF,

613 kW,VAr,VA, kVA, kVAR, kWH, kVAH, kVARH,MDI, Harmonics,Run

Hours, RS-485 Port, LCD display with class-0.5 accuracy for all

incomer feeder.

1Set of R,Y,B phase indication lamps with control MCB as per fault

requirement with each incomer

615 BUSBAR & TVSS

150Amps TP+50%NL, 25kA, 500volts grade busbar chamber of

suitable length with Aluminium busbars mount on SMC supports. All

interconnections shall be as follows; a). Upto 63A, FRLS PVC

insulated copper flexible colour coded wires b). 64Amp to 200Amp

616 Copper Bus-bars and c). 201Amp and above Aluminium Bus-bars ,

current density of bus-bars shall not be less than 1Amps/sq.mm for

Aluminium and 2Amps/sq.mm for copper cross sectional area of

1 No Surge protection device Type 2 ( Class C), 4 Mode, MOV type

suitable for 8/ 20µs surge,Voltage Protection level Up < 1.8kV,

Operating Temperature -40 deg 'c' - +80 deg 'C', Connected

Between 3Nos. phase to neutral and 1Nos. neutral to earth with

discharge Current Imax. ≥ 40KA Per mode & In ≥ 20kA per Mode.

Make & Model: Argos-AG-230-40T2-E or eq. SPD with 63A 4P HRC

fuses of 100kA breaking capacity. For connecting SPD minimum

10sqmm copper wire must be used & length of connecting leads

shall not be more than 500mm for per mode connection with each

busbar including all necessary accessories. The SPD shall

complience with IEC 61643-11 and certified by

TUV,CE,ROHS,UL94V-O..

15 Nos. 40-63A, 4P 'C' Curve 10kA MCB with central overload trip

mechanism and flag indication

3 Nos. 63A, DP 'C' Curve 10kA MCB with central overload trip

mechanism and flag indication

3 Nos. 32A, DP 'C' Curve 10kA MCB with central overload trip

mechanism and flag indication

1 Nos. 63A, 4P 'C' Curve 10kA MCB with central overload trip

mechanism and flag indication

625 METERING, INDICATOR AND RELAYs

Provide 3 Nos. Resin cast CTs, Class-1.0 and MFM True RMS type

digital with min. features of measurements covering A,V,Hz, PF,

626 kW,VAr,VA, kVA, kVAR, kWH, kVAH, kVARH,MDI, Harmonics,Run

Hours, RS-485 Port, LCD display with class-0.5 accuracy for all

incomer feeder.

1Set of R,Y,B phase indication lamps with control MCB as per fault

requirement with each incomer

628 BUSBAR & TVSS

100Amps TP+50%NL, 25kA, 500volts grade busbar chamber of

suitable length with Aluminium busbars mount on SMC supports. All

interconnections shall be as follows; a). Upto 63A, FRLS PVC

insulated copper flexible colour coded wires b). 64Amp to 200Amp

629 Copper Bus-bars and c). 201Amp and above Aluminium Bus-bars ,

current density of bus-bars shall not be less than 1Amps/sq.mm for

Aluminium and 2Amps/sq.mm for copper cross sectional area of

Digitally signed by ANUJ

1 No Surge protection device Type 2 ( Class C), 4 Mode, MOV type

suitable for 8/ 20µs surge,Voltage Protection level Up < 1.8kV,

Operating Temperature -40 deg 'c' - +80 deg 'C', Connected

Between 3Nos. phase to neutral and 1Nos. neutral to earth with

discharge Current Imax. ≥ 40KA Per mode & In ≥ 20kA per Mode.

Make & Model: Argos-AG-230-40T2-E or eq. SPD with 63A 4P HRC

fuses of 100kA breaking capacity. For connecting SPD minimum

10sqmm copper wire must be used & length of connecting leads

shall not be more than 500mm for per mode connection with each

busbar including all necessary accessories. The SPD shall

complience with IEC 61643-11 and certified by

TUV,CE,ROHS,UL94V-O..

12 Nos. 63A, DP 'C' Curve 10kA MCB with central overload trip

mechanism and flag indication

1 Nos. 160A 4P MCCB built in microprocessor based release

(adjustable O/L,S/C&E/F) of fault breaking capacity 35KA

635 (Ics=Icu=100%) upto 415V manually operated with extended

rotary handle with castle lock for door interlock with Phase

spreader & Phase Barriers at both sides. MCCB shall conforming to

IS-1397-2 1993 as amended.

1 Nos. 160 4P Power Contactor with Auto/Manual selector and self

Start/Stop illuminated switch.

637 METERING, INDICATOR AND RELAYs

Provide 3 Nos. Resin cast CTs, Class-1.0 and MFM True RMS type

digital with min. features of measurements covering A,V,Hz, PF,

638 kW,VAr,VA, kVA, kVAR, kWH, kVAH, kVARH,MDI, Harmonics,Run

Hours, RS-485 Port, LCD display with class-0.5 accuracy for all

incomer feeder.

1Set of R,Y,B phase indication lamps with control MCB as per fault

requirement with each incomer

640 BUSBAR & TVSS

200Amps TP+50%NL, 25kA, 500volts grade busbar chamber of

suitable length with Aluminium busbars mount on SMC supports. All

interconnections shall be as follows; a). Upto 63A, FRLS PVC

insulated copper flexible colour coded wires b). 64Amp to 200Amp

641 Copper Bus-bars and c). 201Amp and above Aluminium Bus-bars ,

current density of bus-bars shall not be less than 1Amps/sq.mm for

Aluminium and 2Amps/sq.mm for copper cross sectional area of

1 No Surge protection device Type 2 ( Class C), 4 Mode, MOV type

suitable for 8/ 20µs surge,Voltage Protection level Up < 1.8kV,

Operating Temperature -40 deg 'c' - +80 deg 'C', Connected

Between 3Nos. phase to neutral and 1Nos. neutral to earth with

discharge Current Imax. ≥ 40KA Per mode & In ≥ 20kA per Mode.

Make & Model: Argos-AG-230-40T2-E or eq. SPD with 63A 4P HRC

fuses of 100kA breaking capacity. For connecting SPD minimum

10sqmm copper wire must be used & length of connecting leads

shall not be more than 500mm for per mode connection with each

busbar including all necessary accessories. The SPD shall

complience with IEC 61643-11 and certified by

TUV,CE,ROHS,UL94V-O..

644 6 Nos. 63 DP RCCB (100mA) two per phase

72 Nos. 6-32 SP 'C' Curve MCB with central overload trip

645 mechanism and flag indication of 10kA breaking capacity devided

equally in per phase or as indicated in Single line diagram (12 Nos.

MCB per equally divided in three phases)

All MCB shall be mounted on din channel inside closed chambers

646 shall have Acrylic sheet infront and front door should be a glass for

MS Stand of 450mm height to be provided with black painted.

Note:-The model numbers specified below are only for references

for Shape of the product requirement. The product shall supplied,

648 must match the technical specifications. The technical data sheets

shall be arranged before the material dispatch and got approved

from engineer-in- charge.

Supply of 40W 1200mm LED fitting batten light. (Similar to Havells

Make:DURA BATTEN or Equivalent)

Supply of 15W Recessed mount DownLighter LED fitting .(Similar

to Havells Make: Integra or Equivalent)

Supply of 15W Surface mount DownLighter LED fitting .(Similar to

Havells Make: INTEGRA NXT or Equivalent)

Supply of 9W 2ft Mirror light LED fitting. (Similar to Havells Make:

Lumiline or Equivalent)

Supply of 10W LED Bulkhead Light. (Similar to Havells Make:

Rugby or Equivalent)

Supply of 36W LED 2x2 Light. (Similar to Havells Make:Venus)

Supply of 25W Recessed mount DownLighter LED fitting .(Similar

to Havells Make: Integra or Equivalent)

Supply, Installation, Testing and Commissioning of 1200 mm

sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current

(BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long

down rod, 2 nos. canopies, shackle kit, safety rope, copper

winding, Power Factor not less than 0.9, Service Value (CM/M/W)

minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM

(tolerance as per IS : 374-2019),THD less than 10%, remote or

electronic regulator unit for speed control and all remaining

accessories including safety pin, nut bolts, washers, temperature

rise=75 degree C (max.), insulation resistance more than 2 mega

ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing

etc. complete as required.

Digitally signed by ANUJ

Supply, Installation, Testing, Commissioning of High Power LED

Non Integral Sports Light Fixture with wattage 1000W suitable for

mounting on 36m High Mast tower including suitable remotely

placed power supply , luminaires shall be made of Single piece

High Grade ADC 12 PDC Al alloy housing with extended heat sink

enabling Passive Cooling & offering a totally silent, robust, heat

transfer , Injection moulded special cluster PC lens optics with

standard 20deg/30Deg degree distribution ensuring low glare &

best in class uniformity , corrosion resistant power coating using

nano technology process , including all other accessories and

mounting matching the following specifications :

• Optical Specifications : LED Make : Cree/Nichia/Lumiled with LED

Chip wattage : >2W<=5W & L-70Life: 50000 Burning Hours

657 MR CCT :5700K (tolerances on CCT: +/- as per ANSI C78:377A) & Each 282.00 0.00 150000.00 0.00 42300000.00

SDCM (Mac Adam ellipse): < 5

CRI: >90 ,TLCI>90 . Minimum LPW : 95 lm /watt

• Electrical Specifications :

Operating Voltage: 90-305V AC , High Efficient IP 67 electronic

driver with Flicker free <1%

Power Factor: > 0.95 , Efficiency >90% , THD: <10% ,

Inbuilt Surge Protection: >=6KV L-L & 10kV L-E , 20KV,10KA

Mis Wiring , Short Circuit , Over Voltage & Under Voltage , Thermal

Protections ,Open Circuit & Output failure protections,

• Mechanical Specifications :

Cooling Mechanism : Fixture Housing should be made of SIngle

Piece Pressure Die Cast with Passive cooling

Supply, installation, testing and commissioning of ~40 M high Mast

system, total shaft height ~38m upto bottom of head frame, with

its accessories, Mast shaft shall be in multi sections, hot dip

galvanised and suitable for wind velocity as per IS 875.

• It shall also include accessories for highmast including Fix head

frame and working plateform, suitable for LED Flood light luminaire

symmetrically /asymmetrical and its control gear boxes for

acheiving suitable Avg. lux along with other lighting parametes like

uniformity , Glare etc. as specified in tender & lightning protective

658 finial with power cable, LED aviation light. Each 4.00 0.00 4700000.00 0.00 18800000.00

• Supply of foundation bolts manufactured from special steel along

with nuts, washers, anchor plates,Terminal Boxes (IP:65) for

connection and templates and Design and casting of suitable

shallow foundation with M-25 concrete for the high mast

considering the safe soil bearing capacity at site as 10 T/Sqmtr at

suitable depth.

• The high mast should have provision for accommodating man

rider unit complete as required.

Supply, installation, testing and commissioning Power Lift/Man

raider for accessing head frame unit for maintenance of the Mast

659 and luminaries with an SWL of 300 KG as reqd i/c supplying & Each 1.00 0.00 95000.00 0.00 95000.00

fixing of following accessories including connection, testing etc. as

Supply of 300mm dia sweep energy saving metal exhaust fans

with low power consumption not more than 50 W, ets complete

660 MR with base frame and mounting arrangement with lovers complete Each 32.00 0.00 2780.00 0.00 88960.00

as required. (Similar to Havells Make:VENTIL AIR DS or equivalent)

Supply of outdoor type LED aviation light with covered by acrylic

diffuser, high pressure die cast aluminium housing, prewired

electronic driver complete with all accessories suitable for operation

661 MR on single phase 240V 50Hz AC supply as required. LED is to be No 3.00 0.00 4400.00 0.00 13200.00

provided with individual lense optics to get optimum Optical

performance, with IP-65, IK07 protection.

Supply of 100W LED Flood Light .(Similar to Havells Make: Zeta or

Installation, testing and commissioning of pre-wired, fluorescent

fitting / compact LED fitting of all types, complete with all

MR/ REFER accessories and tube/lamp etc. directly on ceiling/ wall, including

1.41 connections with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5 sq.

664 1.45 mm FRLS PVC insulated, copper conductor, single core cable, Each 67.00 360.46 24150.73 0.00

including providing and fixing phenolic laminated sheet cover on

the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making

665 1.50.1 good the damage, connection, testing, commissioning etc. as Each 32.00 478.49 15311.52 0.00

required. Upto 450 mm sweep

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as

Supplying and installing following size of perforated Hot Dipped

Galvanised Iron cable tray (galvanisation thickness not less than 50

667 4.6 microns) with perforation not more than 17.5%, in convenient

sections, joined with connectors, suspended from the ceiling with

G.I. suspenders including G.I. bolts & nuts, etc. as required.

668 4.6.4 300 mm width X 50 mm depth X 1.6 mm thickness Meter 140.00 1023.96 143354.11 0.00

669 4.6.12 150 mm width X 50 mm depth X 1.6 mm thickness Meter 300.00 761.32 228396.84 0.00

Supplying and installing following size of perforated Hot Dipped

Galvanised Iron cable tray “bends” (galvanisation not less than 50

670 4.7 microns) with perforation not more than 17.5%, in convenient

sections, joined with connectors, suspended from the ceiling with

G.I. suspenders including G.I. bolts & nuts, etc. as required.

671 4.7.4 300 mm width X 50 mm depth X 1.6 mm thickness Each 10.00 1969.23 19692.32 0.00

672 4.7.12 150 mm width X 50 mm depth X 1.6 mm thickness Each 20.00 1350.39 27007.82 0.00

Supplying, installation, testing & commissioning of manual call box

673 17.1.4 of ABS type in surface/recess with stainless steel chain & hammer Each 28.00 433.83 12147.14 0.00

assembly complete with glass and push button etc. as required.

Digitally signed by ANUJ

Supplying, installation, testing & commissioning fire alarm sounder

with facility to make announcement, mounted in A.B.S. box with

674 17.1.7 hinged cover plate & suitable for operation with amplifier i/c line Each 28.00 522.08 14618.25 0.00

matching transformer etc. complete as required.

Supplying, installation, testing & commissioning sector panel

suitable for following zones, complete with visual indications for

675 17.1.9.3 short circuit fault, open circuit fault, fire condition and all other Each 2.00 17317.97 34635.93 0.00

standard facilities as per IS:2189 with mimic diagram for all

area/zone covered, complete with all connections, interconnections

as required. 10 Zone

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,

676 17.5.2 600/1000V rated with annealed copper conductor having XLPE Metre 1229.76 183.95 226215.44 0.00

insulation, steel wire armouring & FRLS outer sheath complete as

Supply of following sizes of 1.1 kV grade multistranded aluminium

677 conductor armoured, XLPE insulated, PVC tape/ extruded inner &

outer sheathed FRLS, power cable as per IS 7098 (Part 1) amended

Laying and fixing of one number PVC insulated and PVC sheathed /

683 7.8 XLPE power cable of 1.1 kV grade of following size on cable tray as

684 7.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Meter 496.00 47.85 23732.86 0.00

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/

40x3mm MS flat clamp)

Laying of one number PVC insulated and PVC sheathed / XLPE

686 7.5.1 power cable of 1.1 kV grade of following size in the existing RCC/ Meter 200.00 39.34 7868.42 0.00

HUME/ METAL pipe as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE

power cable of 1.1 kV grade of following size direct in ground

687 7.1.3 including excavation, sand cushioning, protective covering and Meter 1196.00 448.71 536660.27 0.00

refilling the trench etc. as required. Above 95 sq. mm and upto

688 TERMINATIONS FOR LT ALUMINIUM CABLES

Supplying and making end termination with brass compression

689 9.1 gland and aluminium lugs for following size of PVC insulated and

PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as

Supplying and laying of following size DWC HDPE pipe ISI marked

along with all accessories like socket, bend, couplers etc.

conforming to IS 14930, Part II complete with fitting and cutting,

694 14.16 jointing etc..direct in ground (75 cm below ground level) including

excavation and refilling the trench but excluding sand cushioning

and protective covering etc., complete as required.

Supply, installation, testing and commissioning of 20kVA/ 16kW (

Input 3Phase / output 3 Phase) with Built in Isolation Transformer,

Neutral Passing through, Input/ Output sinwave, Static and

electromechanic, tranfer time <4ms, power factor >0.8 THDi<

10%, Input voltage 220-240V, Output voltage 230V, 50Hz

697 MR frequency, efficiency >80%, 0-40 deg C, 20 min battery back-up Set 2.00 0.00 450000.00 0.00 900000.00

with 12 V Maintenance Free Sealed Lead Acid batteries alongwith

Powder Coated M.S. Rack with unidirectional wheels for housing the

Batteries alongwith all accessories including interconnecting cables,

lugs, Base Frames, Battery Rack & Battery Circuit breaker complete

Modular type Variable Refrigerant Flow/ Variable Refrigerant

Volume air cooled Outdoor units

701 2 INDOOR UNIT-CASSETTE TYPE

704 3 INDOOR Hi Wall Type UNIT

707 4 INDOOR UNIT-DUCTABLE TYPE

708 4.18 7.1TR/High Static Duct Type Unit Nos. 5.00 92805.89 464029.44 0.00

709 4.19 8.0 TR /2800 CFM High Static Duct Type Unit No. 5.00 95261.05 476305.24 0.00

710 5 Copper refrigerant pipe work

721 18.7 DRAIN PIPING

722 18.7.3 25 MM Nominal Outerdia Pipes RMT 725.00 392.57 284613.51 0.00

723 18.7.4 32 MM Nominal Outerdia Pipes RMT 325.00 510.97 166064.86 0.00

724 16.12.1 Rectangular GI Ducting (Factory Made)

728 16.12.2 Rectangular GI Ducting (Factory Made)

732 16.13 GI volume control duct damper SMT 4.00 6911.45 27645.80 0.00

733 16.15 Aluminium Supply Air Grills SMT 8.00 9016.78 72134.27 0.00

734 16.16 Aluminium Return Air Grills SMT 8.00 5855.59 46844.74 0.00

735 16.17 Aluminium Supply Air Diffuser SMT 6.00 12082.28 72493.67 0.00

Digitally signed by ANUJ

736 16.18 Aluminium Return/Exhaust Air Diffuser SMT 6.00 8037.48 48224.91 0.00

737 16.21 25 mm thick Acoustic Lining SMT 50.00 687.96 34397.76 0.00

738 16.23 Nitrile Rubber Insulation

739 16.23.1 19 mm Thick Duct insulation SMT 305.00 741.12 226041.63 0.00

Main Intelligent central controller system Manual Touch Screen

Suitable for Ground & First Floor &second

742 MR-3 Refrigerant Gas to Top up the system Kgs 245.00 0.00 946.00 0.00 231770.00

743 MR-5 300 CFM PROPELLER Fan at 15mm Static Pressure Nos 12.00 0.00 10500.00 0.00 126000.00

Axial Flow fans for make up air & Pressurization system. Axial Flow

744 MR-6 Fan 5000 cfm at 25 mm static for Make Up Fresh air in case of Fire No 2.00 0.00 67500.00 0.00 135000.00

Lift Well. Fan Dia 710, RPM not More than 1450. Motor Kw= 3.7

745 MR-7 Double canvass connection Fire Rated SMT 4.00 0.00 3600.00 0.00 14400.00

746 MR-8 Aluminium Fresh/Exhaust air louvers Bird screen type. SMT 2.00 0.00 11700.00 0.00 23400.00

747 MR-9 Under deck Insulation SMT 485.00 0.00 630.00 0.00 305550.00

HVAC PANEL-2, Emergency panel For Pressurization system &

749 Outgoing feeder for Starter panel of Fresh Air & Smoke Exhaust No. 1.00 0.00 135000.00 0.00 135000.00

fans at each floor

750 Communication Control Wire 2c x 1.5 RMT 625.00 0.00 106.00 0.00 66250.00

751 Copper Conductor Cable 3c x 2.5 RMT 278.00 0.00 188.00 0.00 52264.00

752 Copper Conductor Cable 4c x 6 RMT 40.00 0.00 570.00 0.00 22800.00

753 Copper Conductor Cable 4c x 10 RMT 50.00 0.00 991.00 0.00 49550.00

754 Copper Conductor Cable 4c x 16 RMT 110.00 0.00 1550.00 0.00 170500.00

755 Copper Conductor Cable 4c x 25 RMT 20.00 0.00 1710.00 0.00 34200.00

756 G.I Perforated Cable Tray with Cover 300x100x1.6 RMT 50.00 0.00 1515.00 0.00 75750.00

757 G.I Perforated Cable Tray with Cover 200x100x1.6 RMT 70.00 0.00 1140.00 0.00 79800.00

759 MR-11 INTERNAL FIREFIGHTING SYSTEM

(A) Supplying, installation, testing and commissioning of electric

760 driven terrace pump with Electrical Panel suitable for automatic

operation and consisting of following, complete in all respects, as

required: (Terrace Pump)

(B) Horizontal type, multistage, centrifugal, split casing pump of

761 cast iron body & bronze impeller with stainless steel shaft,

mechanical confirming to IS : 1520

(C) Suitable HP squirell cage induction motor TEFC type suitable for

operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class

762 of protection for enclosure, horiziontal foot mounted type with

Class-'F' insulation, conforming to IS-325.

(D) M.S.fabricated common base plate, coupling, coupling guard,

foundation bolts etc.as required.

(E ) Suitable cement concrete foundation duly plastered and with

anti vibration pads.

Supplying and fixing of fire brigade connection of cast iron

body with gun metal male instantaneous inlet couplings complete

766 with cap and chain as reqd. for suitable dia MS pipe connection Each 1.00 7168.77 7168.77 0.00

conforming to IS 904 as required : 2 way - 100 mm dia M.S. Pipe

Providing & fixing of pressure switch in M.S. pipe line including

connection etc. as required.

Supplying and fixing single headed internal hydrant valve with

instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia

768 with cast iron wheel ISI marked conforming to IS 5290 (Type -A) Each 4.00 6527.60 26110.39 0.00

with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Stainless steel

Supplying & fixing 63 mm dia gun metal short branch pipe with 20

mm nominal internal diameter size nozzle conforming to IS 903

769 suitable for instantaneous connection to interconnect hose Each 4.00 1767.20 7068.82 0.00

pipe coupling as required : Stainless Steel (Grade 304)

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63

770 mm dia male and female couplings duly bound with GI wire, Each 8.00 4729.56 37836.47 0.00

rivets etc. conforming to IS 636 (type-A) as required : Stainless

Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction

spray painted in post office red, conforming to IS 884

complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile

reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S.

Pipe and socket. 30 m

Providing and fixing angle iron (40mmx40mmx5mm) door frame

and MS sheet (6mm thick) cum glass shutter of size

2.1mtrx0.9mtr(N.S.) with 25mmx25mmx3mm angle frame all

around and stiffened in between i/c hinges, handle, locking

772 arrangement, painting with approved synthetic enamel paint i/c Each 4.00 0.00 7956.00 0.00 31824.00

sign writing on glass at internal hydrant including providing & fixing