SPECIAL REPAIR TO BLDG NO KP 73 AND KP 76 08 QTRS OF OFFRS MD ACCN IN KIRBY PLACE UNDER GE NORTH DELHI CANTT

Amount

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

Demolition of reinforced cement concrete in roof floor (other than ground floors) beams staircase, landing chajja and similar suspended work complete all as specified.

M&L for Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregate) as in chajjas and the like, all as specified and directed by Engr-in-Charge.

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, rough finished surface of concrete, all as specified .

M&L for TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for TMT bars 6mm to 8mm dia in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

Demolition of cement concrete (unreinforced) in ground floor and in paving exceeding 15 cm thickness (below or above ground floors) complete all as specified.

M& L PCC 1: 5 : 10 type E2 using 40 mm graded brick aggregate as in filling under sunken floors etc complete all as specified.

M&L for priming surfaces with bituminous primer conforming to IS-3384 @ 0.30kg/sqm, after drying of primer applying a coat of hot blown bitumen conforming to IS-702 @ 1.20 kg/sqm and layin polymeric water proofing membrane, five layerd with centre core of 90 micron high molecular density polythelene film (min weight 3kg per sqm) with end over laps not less than 150mm and side lap 75 mm and applying a coat of semi hot blown bitumen 85/25 grade @ 0.50kg/sqm and dusted over the bitumen coat as in sunken floor complete all as specified.

M&L for glazed coloured ceramic tiles in dado/vertical surface (350mm x250mm x 7 mm/450x300x7mm) thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface including 10 mm thick backing in cement mortar 1:3 even and fair for receving tiles on vertical surface and taking down cement plaster on brick walls including raking out joints, hacking for key, scrubbing down with water, complete all as specified and directed by Engr-in-Charge.

M&L for Non skid coloured tiles (square/rectengular) 7 to 8 mm thick area of each tile size exceeding 0.06sqm but not exceeding 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the surface,including 10 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for Vitrified Ceramic dark shade tiles 10 mm thick (square/rectengular) polished, area of each tile n. exc 0.36 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface insluding 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

All as per item No 12 but on vertical surface as in skirting ,including 10 mm thick rendering in CM 1:3 even on fair faces of brick work including taking down cement plaster on brick walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engr-in-Charge.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified.

M&L for Rendering 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions if required complete all as specified. (Water proofing compound to be measured and paid for separately).

M&L for Rendering 10mm thick on fair faces of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.

M&L for Rendering 10mm thick on fair faces of brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement all as specified.

Supply only liquid water proofing compound complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt ), all as specified and directed by Engineer-in Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed by Engineer-in Charge.

Taking down shutters of any description exceeding 1 square metre and not exceeding 2 square metre each complete , all as specified and directed by Engineer-in Charge.

S&F 40mm thick flush shutter (Factory made) soild core construction, with black board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F rolled mild steel in Fe 410-W (Gde-E-250 quality A) framing for door/vent/CB chowkhats and the like fixed with angle cleat and connecting plates also fastening and fixing incluidng welding 3 Nos MS butt hinges 100mm & 01 No 50mm complete (Butt hinges shall be measured and paid for separately).

M&L for factory made, 2nd class hard wood 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L 30mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamfered or rounded. Fitted with cut and mitred beads for securing glass, etc; sizes of member of shutters as specified in SSR Part I,Section 8, clause8.24(a); supplied and fitted to chowkats, complete all as specified and directed.

S&F Factory made UPVC white colour sliding windows area n. exc 2.00 sqm each. Three track made of extruded profiles with wall thickness of 2.3 mm (+/- 0.20 mm). Windows profiles with hollows section with multi chamber. Frame size (88 mmX 52 mm). Sliding sash (42 MM X 67 MM), sliding Mesh sash (42 mmX 57 mm), sliding interlock (one vertical length in each shutter)(45.5 mmX 28 mm).glazing bead (24.5 mmX 16 mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing of hardware and drainage of water etc, making arrangement for fixing of hardware, EPDM gasket, 1.2+/- 0.20 mm thick galvanised steel frame (30mm X 18 mm) 2 nos sliding sash ( 30mmX 18 mm), sliding mesh sash(26 mm X 10 mm),profile to be inserted in required profile frame will be fixed to the wall with 8 mm X 100 mm long fastener hardware.(Touch lock of zinc alloyed (white powder coated ), steel roller system, Staineless steel wire 0.36 mm nominal dia of wire and averahe width of aperture 1.40 mm and required accessories) Note:- The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories ie, wire mesh and hard wares. Net opening wil be measured for payment purpose, as specified and directed.

S&F Factory made UPVC white colour casement (openable) window area n. exc 1.00 sqm each made of extruded profiles with wall thickness of 2.3 mm (+/- 0.20 mm). Windows profiles with hollows section with multi chamber. Frame size (60 mmX 58 mm). sash (60 MM X 73 MM), T profile (one vertical length in between two shutters) (60 mm x 74 mm) , Glazing beads (35 mm x 20 mm) will mitered cut and fusion welded at all corners, including drilling of holes of fixing of hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM, gasket, 1.2 +/- 0.20 mm thick galvanised steel frame (28 mm x 21.5 mm), sash (31 mm x 27.5 mm), T profile (27 mm x 17 mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners. Hardware : (casement handle made of zinc alloyed (white powder coated), But hinges of zinc alloyed (white powder coated) transmission gear made of mild steel with multi point locking system) and 5 mm thick glazing with of glass and includes all another connected accessaries i.e. wire mesh and hardwares complete all as specified and directed. Note:- The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks and similar work conforming to Fe 290 Gd E-165 all as specified .

M&L for providing cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates for hold fast complete all as specified.

M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including screed bed or bedding layer of mortar 20mm thick in cement mortar 1:3 laying floor finishes complete all as specified.

M&L for machine cut kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with 15 mm thick of CM (1:3) back coat including taking down cement plaster on brick walls including raking out joints, hacking for key, scrubbing down with water, complete all as specified and directed by Engr-in-Charge.

M&L for 150mm wide strip of makrana white marble 18- 20 mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types with 20mm thick screed bed or bedding layer in cement mortar 1:3 laying floor finishes . all as specified.

Rounding to edges of Granite/marble slab one edge, such as in steps, cooking platform, and or similar works complete all as specified.

Demolition of brick/stone masonry built in CM including all quoins, arches, pillars, etc bbut excluding ashlar facing, dressed stonework and precast concrete articles, complete all as specified.

M&L brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 all as specified.

M&L brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 but except bricks all as specified.

M&L Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 all as specified and directed.

M&LProviding cement concrete1:2:4 type B-0 (12.5mm grade crushed stone aggregates) in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed.

M&L Roughening surfaces of old concrete surfaces by picking sweeping, cleaning and washing down with water to remove dust etc including brushing neat cement slurry with 3.0kg of cement per Sq meter, etc complete all as specified.

M & L for Water proofing treatment to RCC roof slab, walls, chhajjas etc, shall be carried out as specified below and as directed by Engineer-in-Charge. (a) M&L for 15mm thick plaster screed bed layer in CM 1:3 on concrete surfaces. (b) Preparing plastered surfaces of roof slab, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & evenly applying a coat of approved bituminous primer @ 0.20 Kg/Sqm of area complete all as specified. (c) Laying APP polymer modified approved membrane, non woven, polyester, weighing not less than 3.5 Kg/Sqm with laps & overlaps as specified & joints sealed and applied complete by torch application method all as specified & directed by Engr-in-Charge. Carrying out test by flooding water for 24 hrs for leakage & seepages and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specified & as directed by Engr in Charge. Note: For MOU ref Sch 'A' Notes.

M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand blasting, scrubbing down concrete sufrace with wire brushes cleaning with water allowed to dry and applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited all as specified and applying two layess of guniting over steel welded mesh 2mm dia of wire and aperture 75mm,total thickness of gunite n.exc 25mm thick (average thickness) in cement mortar 1: 2 using OPC 53 grade cement mixed with polycrete admixture @ 2% by weight of cement or as per manufacturers instructions and finally applying cement plaster over gunited surface of required thickness to give even, uniform and smooth finish conforming to proper gerometrics in cement mortar ( 1 : 3) to match with the existing surface as in sides and soffits etc of slabs, chajjas, fins, facias, parapets , columns and beams etc complete including necessary scaffolding, shuttering, necessary chases to brick work or RCC members at any height upto 4 storey bldgs all as specified. (Note : Steel welded mesh is to be tightend / welded with the existing re-inforcement. The cost of welded mesh is deemed to be included in the unit rate quoted by the contractor).

M&L for providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

S&F 5 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified.

S&F 5 mm thick sheet glass frosted ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of apreture 1.40mm and fixed with tinned teaks or stainless steel wire staple complete all as specified.

S&F mild steel sliding door bolt plate type 250 mm long stove enamelled black with bright bolt not less 12 mm dia bolt with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified .

Supply and fixing of mild steel cold rolled butt hinges medium weight 100 mm log fixed to steel /angle iron frame by welding ,if required complete all as specified.

All as above item no 48 but 75mm.

S&F continuous M S CP piano type hinges 30mm flap (when opened ), bright finish or electrogalvanised complete all as specified.

S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed.all as specified and directed.

S&F for 150mm size aluminium anodised handle of fabricated type and fixed.all as specified and directed.

S&F 100mm size hasp and staple safty type aluminum anodized with mild steel hinges pin including bolt to hinge plate and fixed with screw complete all as specified.

S&F 150mm ordinary rat tail rod pattern spring incl roller and roller plate (mild steel). all as specified.

S&F mild steel barrel tower bolts, stove enamelled black, with bright bolt 200mm long. all as specified.

S&F20 mm dia decorative draparycurtain road with bibs, braked & internal funnels. complete all as specified.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings.

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site. complete all as specified.

S&Fvitreous China wash basin, white, flat back size 550x400mm excluding tap, chain, plug but including brackets, waste fitting 32mm dia ,brass chromimium plated for glazed ware sink, basin,with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified.

S&F 15 mm CP mixer suitable for WHB for fixing hot & cold waterscrewed down for iron pipe and fixed all as specified and as directed.

M&L for preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified.

M&L for preparation of steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of zink chrome primer. all as specified.

M&L Preparing new/ old surfaces, plastered or unplastered of walll and applying two coats of weather proof exterior emulsion paint (Apex Ultima) on any surface as approved and directed by Engr-in-charge.

M&L preparation of new plastered surfaces of ceiling and apply two coat of oil bound distemper over a coat of primer incl 1mm thick wall putty finish to ceiling all complete all as specified.

M&L preparation of old plastered surfaces of ceiling and apply two coat of oil bound distemper over a coat of primer incl 1mm thick wall putty finish to ceiling and complete removal of existing treatment from old surface, all complete all as specified.

M&L two coats of oil bound distemper on walls including preparation on new surfaces over coat of primer incl applying 3 mm thick layer of wall putty on walls to give uniform surface complete all as specified and directed.

M&L for applying two coat of oil bound distemper over one coat of primer including preparation after complete removal of existing treatment from old decorated plastered or unplastered surfaces of walls incl applying 3 mm thick layer of wall putty on walls to give uniform surface complete all as specified.

M&L two coats of cement cement base paint on walls including preparation on new/old surfaces complete all as specified and directed. .

S&F in repair PVC low level flushing cistern 10 ltrs capacity incl PVC float valves and out let pipes includes brackets for fixing complete.

S&F in repair Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodized, fixed with rawl plugs. all as specified.

S&F PVC connection 15mm size with PTMT nuts of lengh 450mm complete all as specified.

S&F C P brass magic eye in main door as per sample

S&F steel peg set colour coated of six as per sample

S&F sinks with drainage board made of stainless steel I mm thick kitchen or laboratory with plugs,washers and wastes coupling including bedding in cement mortar to dwarf wall, neccessary masonary work or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 405mm x 355mm x178mm . complete all as directed.

S&F in repair 1mm thik plate rack made of stainless steel, 600 x 750X250mm(Wt not less than 7.5 Kg) including brackets and embedded in brick wall all as specified and as per manufacturers instruction.

Dismantling cast iron & reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required of any dia upto 100mm. all as specified.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints laid in trenches or floors all as specified.

All as per srl item No 78 above but 75mm bore pipes ditto.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints fixed to walls duly apply a coat of bitumenous black paint complete all as specified and directed.

All as per srl item No 80 above but 75mm bore pipes fixed to wall ditto.

All as per srl item No 80 above but 50mm bore pipes fixed to wall ditto.

Fixing only 100mm dia CI soil waste and vent pipe in any length with or without ears with cement joints fixed on walls complete all as specified and directed.

All as per srl item No 83 above but 75mm bore pipes fixed to wall ditto.

All as per srl item No 83 above but 50mm bore pipes fixed to wall ditto.

S&F Salt glazed stone ware gully traps square or round mouthed, type P of size 150x150mm set and jointed to drain pipe with cement mortar (1:1) including demolition of old unserviceable gully traps. all as specified.

S&F Cast iron bend (any radius) diminishing pieces or tapers 100mm bore fitted with oval access door. all as specified.

S&F Cast iron bend (any radius) diminishing pieces or tapers 75mm bore fitted with oval access door.

S&F Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100/110mm bore pipe.complete all as specifiecd and directed.

S&F Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore complete all as specified.

S&F Cast iron branch pieces single (equal unequal ordinary or inverted (Spigot or socketed type) or with parelled branches 75mm bore (fixed in repairs)

S&F Cast iron branch pieces single (equal unequal ordinary or inverted (Spigot or socketed type) or with parelled branches 100mm bore (fixed in repairs) all as specified.

PVC (SWR) pipes 110mm bore single socketed , in any length with rubber ring joints fixed to wall

S&F cast iron vent cowl for 50mm dia pipe. all as specified.

S&F cast iron floor trap 75 mm, with grating including jointing to waste pipe . all as specified.

S&F Cast iron work in lids for oval access doors for 75mm bore pipes and fittings including all necessary threading and nut/bolt required as directed by Engr in charge.

S&F Cast iron work in lids for oval access doors for 100mm bore pipes and fittings including all necessary threading and nut/bolt required as directed by Engr in charge.

M&L for machine cut polished granite stone slab 18-20 mm thick fixed over screed bed 15mm thick CM 1:4 including cutting/ jointing pointing with white/coloured cement to match existing complete all as specified and directed by E-I-C.

S&F in repair 32/40 mm dia PVC waste pipe for WHB/sink complete all as specified

Taking down door shutters of any description exceeding 1 square metre and not exceeding 2 square metre each easing, and adjusting as required and re-fixing in same opening including renewal of screws complete , all as specified and directed by Engineer-in Charge.

M&L for 5.5mm thick plain sheet glass n.exc. 0.50 sqm each in fixed with wooden beads in kitchen cabinate shutters all as directed.

S&F 40mm dia cupboard knobs fixed with nut screw and washer of mild steel, bright finished

S&F in repair elegent mirror PVC cabinet with towel rail of size 450x600x150 mm all as specified (Make : prayag Cat No. 551 or equivalent of ZIM/ JAQUAR )

S & F Glass Shelf Corner trangular type shelf 300X 300 mm with CP brackets fancy type 6mm thick glass Make : prayag/Zim

M&L numbering tiles of size 100x200mm duly marked with letters and numbers with paint and fixed in CM (1:4) for numbering of bldgs all as directed at site by Engineer-in-Charge

S&F floor door stopper, aluminium alloy body and tongue anodised with hard drawn steel spring of 140mm size overall.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), floor mounted with inbuilt P trap in white colour, including connection to trap and to flushing pipe including provn of cement concret beading complete all as specified and directed.

S&F EWC Seat cover white colour of PVC complete all as specified and directed.

Providing and injecting chemical emulsion for post constructional Antitermite treatment along external wall where the apron is not provided using chemical emulsion at rate 7.5 liters per Sq.m of the vertical surface of sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified.

Treatment of soil under exiting floors using emulsion @ one literper hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 Cement: 2 coarse sand) to match the existing floors.

S&F for 18/19mm thick one side decorative lamination amd other side balancing white sheet consisting of carcass 18/19 mm thick PVC sheet including 6 mm thick one side decorative and other side balancing white sheet and 200 mm wide &1 mm thick PVC EDGE Banding tape of 0.80 mm pasted to edges of PVC board with approved adhesive and self tapping screws all as specified and directed.

S & F Kitchen Carcas made of 18mm thick (WPC) with both side laminated approved shade with machine pressed edge banding tape of 0.80 mm thick shutters including the provision over head cabinet with shelf handles with LED light, Lacquer Glass cabinet with handle, Grain trolley, Cargo Basket, Pot and Pan, PVC Cutlery tray innotech, left and right side under counter tray innotech, left and right side under counter Board cabinet including hardware accessories, PVC legs 100mm, PVC Skirting 88 mm innotech, 171 mm innotect pot and pan, bottle pull out 200 mm, 600mm Cutlery Tray, GT PT 900 mm, hinges "O" & "8" crank, Auto lid open waste bin plastic and 3W LED Light with On/Off switch connection etc complete all as shown on Plan, Elevation 'A' and Elevation 'B' as shown on drawing No 1, 2, 3 complete all as specified and directed.

Taking up or down 15 mm dia steel water tubing and connections including all fittings, including cleaning for refixing or removall to store after cleaning.

Taking up or down 20 mm dia steel water tubing and connections including all fittings, including cleaning for refixing or removall to store after cleaning.

M & L 15mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and ceiling or laid under floors etc complete all as specified.

M & L 20mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and ceiling or laid under floors etc complete all as specified.

Refixing 15 mm bore old steel water tubing medium grade galvanised and with all fittings, connections in new or old position (walls, ceiling, floor etc.) complete all as specified.

Refixing 20 mm bore old steel water tubing medium grade galvanised and with all fittings, connections in new or old position (walls, ceiling, floor etc.) complete all as specified.

M&L Gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe of size 25mm

M&L Gun metal globe of gate valve with iron wheel head, screwed both ends for iron pipe of size 20mm

S&F fancy type chromium plated stop valve cast copper alloy, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions of size 15 mm. all as specified

-ditto as item ser no 120- but fancy type, chromium plated with long shank and cup (concealed type)

S&F of Bib tap cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe of size 15mm bore, all as specified

S&F Ball Brass Valve high pressure with polythene float and flynut complete screwed for Iron pipe or brass ferrule and fixed of size 25mm bore. all as specified

S&F in repairs shower rose fancy type brass chromium plated 125 mm size heavy duty pattern with swivel joints type screwed for 15mm bore including jointing to pipe or unions complete all as specifed and directed.

Dismantling water tanks and removing to store exc 500 & n.exc 1000 ltrs of capacity. all as specified

S&F rotational moulded polyethylene water storage tanks tripple layered ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 liters including all accessories complete all as specified .

S&F in repair 2 in 1 Angle Valve 15 mm CP fancy pattern type cast copper alloy screwed for iron pipe or forbrass ferrule and fixed all as specified and as directed.

S&F in repair Angle Valve 15 mm CP fancy type cast copper alloy screwed for iron pipe or brass ferrule and fixed all as specified

S&F in repair CP hand spray (health facucet with 1.5 M long easy flex tube in chrome finish and wall hook) complete all as specified and directed.Cat part No ALD-CHR-583 of make Jaquar or eqv as approved by GE.

S&F in rep chromium plated jet for WC with 1.00 M long PVC pipe including all necessary fittings complete all as specified and directed.

M&L for pcc type D-2 ,1:4:8 ,using 40mm graded crushed stone aggregate as in sub base , mass concrete or foundation filling all as specified. .

M&L for coloured precast cement concrete interlocking tiles 80mm thick, M-35 grade of any shape and size, conforming to IS-15658-2006 glossy finish as in floor/pavement laid on 75mm thick stone dust cushioning, laid dry to the profile over rammed earth/murrum filling complete all as specified & directed.

M/L PCC 1:2:4, type B1 using 20mm graded crushed stone aggregate as in bencing and coping, apex stone etc all as specified and directed..

M&L for brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:4. all as specified.

M&L for cleaning of manholes not exc 1.50m deep and removing sludge/waste materials etc. to a distance not exc. 1.5m and burring in pits including fillling pits with earth all as directed by E-in-Charge.

Cleaning of drain pipes 150mm bore by rodding from manhole to manhole or manhole to septic tank or vice versa and well flushing with water after cleaning (the rates include for taking off manhole covers and replacing, removing the sluldge and burrying in pits at a distance not exc. 50m as directed by the Engr -in- charge.

Excavation in trenches not exc 1.5m wide and not exc. 1.5m depth in any type of soil for foundation etc or for shafts, well drain pipes getting out in any type of soil complete all as specified.

Returning fillling in including spreading, levelling watering and well ramming in layers not exc 25cm thick in each layer complete all as specified.

Removing excavated soil to a distance n exc 50m and depositing at alevel n exc 1.5m above the starting point. all as specified.

Demolition & breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of 100/150mm dia pipe all as specified.

M&L for Plain cement conc 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore pipes all as specified.

M&L for 150mm bore salt glazed stone ware drain pipes laid in trenches and jointed as specified.

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete ,using extra cement ,incl forms moulds ,mitered/stopped ends etc

M&L PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in surface channels/drains all as specified.

S&F SFRC manhole covers and frame medium duty of overal size 600mmX600mmX80mm thick, factory made and test load 10 tonnes (MD-10), strength as per IS: 1726-1991 (Make-Polycrete) all as specified by Engineer-in-Charge.

M&L for brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:4 but except brick all as specified.

M&L for PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in surface channels and drain beds

S&F for 110mm bore pvc (SWR) pipe single socketed cut to size reqd as in weep holes

Taking down carefully copper / aluminium point wiring (light / fan socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing all as specified and directed.

Material and labour for point wiring for light/fan/ bell / buzzer/socket on independant board with 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with using colour coding and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of modular metal flush box, modular white cover plate with frame, blanking plate etc suitable for Mylinc / Coral / Sleek model accessories etc and making good to the disturbed surfaces to match the existing complete all as specified and directed.

All as per item No-150 here-in-before but for one light point controlled by two 2- way switches complete.

All as per srl item No-150 here-in-before but one 3 pin, 06 Amps socket outlet point on same board controlled by one, one way 06 Amps switch.

All as per Serial Item No-150 above but point wiring with 2.5 Sqmm single core FRLS cables and earth continuity wire of 1.5 Sq mm single core FRLS cable for one 6 pin 15 Amps socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

Material and labour for sub main wiring with 04 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with using colour coding and including continuous earth wire of size 2.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed. Note:- 02 RM of 04sqmm wie + 01RM of 2.5sqmm+01 RM of PVC conduit= 01 RM to be measure.

Supply and fixing modular switch, 06 Amps, single pole, one way, 230 volts, one module and IP 20 protection complete all as specified & directed.

Supply and fixing modular switch, 06 Amps, single pole, two way, 230 volts, one module and IP 20 protection complete all as specified & directed.

Supply and fixing modular bell push with indicator, 06 Amps, single pole, one way, 230 volts, two module and IP 20 protection complete all as specified & directed.

Supply and fixing modular switch, with indicator, 16 Amps, single pole, one way, 230 volts, one module and IP 20 protection complete all as specified & directed.

Supply and fixing modular socket outlet 05 Pin, 06 Amps, 02 module with shutter complete all as specified & directed.

Supply and fixing modular socket outlet 02 in 01, 06 pin, 06 Amps and 16 Amps, 02 module with shutter complete all as specified & directed.

Supply and fixing ding dong bell, AC, 230 volts, single pole complete all as specified & directed.

Supply and fixing ceiling fan regulator, stepped type of 0 to 04 rotary steps, electronic, 02 module, humfree, AC, 230 volts, 100 watts, duly ISI marked complete all as specified & directed.

Supply and fixing ceiling rose, 6 Amps, 230 volts, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25mm size complete all as specified & directed.

S&F Exhaust fans of 250 mm sweep (non metallic type) 240 Volts, AC, 50 Hz including cutting of holes in wall, including making of wooden / iron frame suitable for fixing of fan where required etc complete all as specified and directed. (Make : Havells Model No Ventil Air Dx WHT BLK) or equivalent in Bajaj/ Crompton.

Supply and fixing lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting including 7W LED bulb complete all as specified & directed.

Supply and fixing decorative wall mounting light SS finish fixture with textruded glass difuser suitable for up to 40 watt mini glass lamp, lamp holder, including 9 Watts LED bulb in warm white clour of 6500 K of B22 base cap and all accessories pre-wired including connecting up including taking down of existing u/s light fitting complete all as specified and directed.

Supply and fixing 5 Watt LED fitting (1 fit) attractive wall mounted type suitable for mirror fittings, all accessories pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size, including taking down of existing u/s light fitting complete all as specified and directed.

Supply and Fixing 9/10W LED fitting (2 fit) attractive wall mounted type suitable for mirror fittings, all accessories pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size, including taking down of existing u/s light fitting complete all as specified and directed. Make : Havells Cat part No: LUMILINEBS9WLED865SPCWH/ Wipro Cat part No:LL20111XXX65NE3 or equivalent in Philips.

Supply and fixing on wall / ceiling LED batten lighting fixture 20 watts LED 6500K (4'), with Extruded aluminium housing and integrated electronic driver and all accessories pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size with connector block, including taking down of existing u/s light fitting complete all as specified and directed. Make : Havellst Cat part No:ENDURALINEARNEOB20WLED865SPCWH/ Wipro Cat part No: LL20-221-XXX-65NE3 or equivalent in Philips.

Supply and fixing in repair energy saving security light fitting of 45 watts LED environmental friendly pressure die-cast aluminium IP 66 roadway luminaire with high power LED as light source comprising with electronic driver and all accessories pre-wired incl connecting up with PVC insulated copper conductor cable 1.5 Sqmm, 3 core as required for connections and 40 mm bore light grade G. I. tube mounting bracket of 1.5 meter in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed. Make : Havells Cat part No: ENDURAPEARLNEOSL45WLED757SASYTOPC or equivalent in Philips / Wipro

Material and labour for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed. Note:- 02 RM of 04sqmm wie + 01RM of 2.5sqmm+01 RM of PVC conduit= 01 RM to be measure.

Supply & fixing in repair industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volts of 20 Amps, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fixing in repair sheet metal enclosure distribution board, single pole and neutral, AC, 240 volts, 08 way, with 200 Amps rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified directed.

Supply and fixing in repair MCB, SP, AC, 240 volts of 10 to 32 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fixing in repair MCB, SPN, AC, 240 volts of 40 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fixing in repair MCB, SPN, AC, 240 volts of 63 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fixing in repair sheet metal enclosure distribution board triple pole and neutral (VTPN), AC, 440 volts, 04 ways with 200 Amps rated copper bus bar and metal door with IP 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed and comprising of the following:- (a) MCCB, 160 Amps, 04 pole, AC, 415 Volts of 16 KA breaking capacity complete - 01 No. (b) MCB, SP, AC, 240 volts of 63 Amps, "C" curve, 10 KA breaking capacity - 12 Nos.

Taking down carefully of existing geyser after disconnecting the electric connections and supply and fixing of new Geyser 25 Ltr capacity having copper tank, 230V, AC in wall with suitable size nut bolts and washers complete and unsv Geyser depositing in E/M store yard all as specified and directed by Engr-In-Charge. Make- Havells Model No MONZA or equivalent in Bajaj / CG.

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried vertically in ground (earth pit not less than 2.25meter deep below ground level) with top edge of the plate not less than 1.5meter below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 75mm center to center both way with 12mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40mmx40mmx3mm frame for pit cover including testing on completion complete all as specified and directed.

Taking down carefully ceiling/exhaust fan of any sweep complete with all accessories, dismantling blades and kept in safe custody including painting complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and hanging and connecting up with provn of 3 core copper flexible cable of size 1.5 Sqmm from ceiling rose to fan complete all as specified & directed by Engineer - in - Charge.

Taking down carefully existing electric meter any type any make after disconnecting the electric connections and refixing the same with and including new Polycarbonate thermoplastic meter box with transparent hinged lid with sealing provision, internally embedded gasket of size 217 x 253 x 115 mm suitable to accommodate single phase KWH meter and connecting up including making good the disturbed surfaces all as directed by Engineer - in - charge. Make :- Hensel, Cat Part No. KG 9003 or equivalent

Supply and fixing of 300mm sweep, 900 RPM, exhaust fan, heavy duty with louver shutter, frame, blades complete and unsv fan depositing in E/M store yard all as directed.

Taking down of existing u/s Post top light fitting and supply & fixing 40 watt LED post top lantern including suitable size medium grade galvanized iron pipe of size 40/50mm up to length of 0.4 Mtrs and necessry plain cement concrete (1:3:6) type CI (using 20mm graded crushed stone aggregate) as in copings incl necessary form work complete all as specified & directed by Engr-in-charge. Make: Crompton greaves Cat part No: LPTO-40/CDL or equivalent in Philips/Wipro

M&L for Sand coarse filling in trenches obtained from local river for cushioning of UG cable all as specified and directed . Note:- Punned thickness will be measure for payment.

Supply and laying well burnt best quality locally available bricks of size 25X12.5X7.5 cm (+/-) 8% tolerance laid flat for protection of UG cable all as directed .

M&L tubing GI light grade laying for protection of LT under ground cable of size 40mm bore

Supply and laying including connecting and testing of LT under ground electric cable of size 06 sqmm 2 core XLPE insulated and PVC sheathed armoured heavy duty multi stranded 1100 Volts grade with aluminium conductor, laid in trenches or drawn through existing pipe or fixed to wall with providing suitable size of aluminium lugs, GI nuts bolts and washers complete wherever required all complete all as specified and as directed .

Shiv Shankar Nirman Co.

V M CONSTRUCTION

imran construction company

SHREE RAM BUILD TECH

The new hut furnitures

garnet engineers contractors

SHEELSONS ENTERPRISES