SPL REPAIR OF BLDG NO P 3 TA LINE AT C HILL AND CERTAIN OTHER SANCTIONED WORKS UNDER GE NAGROTA

Amount

SCHEDULE A PART-I Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.50 sqm each and removing from site.complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm eachand n exc 4 sqm and removing from site.complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings dressed stone work and precast concrete articles.complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and paving not exc 15cm thickness.complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of any description and any pcomplete all as specified and directed by Engineer-in-Charge.osition not other wise specifically provided.

Demolition of cement concrete (Reinforced) of any description and any position not other wise specifically provided reinforcement cut as required to facilitate demoltion complete all as specified and directed

Demolition of Stone slabs and tiles of any description or thickness of floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge

Taking down cement plaster on brick or stone wall etc including racking out joints, hacking for key scrubbing down with water etc to receive new plaster etc. complete all as specified and directed

M & L for Pressed steel frames of size 125 mm X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including two coats of synthetic enamel paint over one coat of red oxide complete all as specified and directed .

M & L for Pressed steel frames of size 105 mm X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including two coats of synthetic enamel paint over one coat of red oxide complete.

M & L forBox type Steel window side hung double shutters with provision for desert cooler/AC(inside for wire mesh & out side for glass), including guard bar,hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded and fixed, steel window shall be conforming to relevant IS complete all as shown on drawing No CEUZ/TD/1302/09, Sh 1/3 to 3/3 complete all as specified and directed Note:- Wire mesh and sheet glass shall be measured and paid separately

S & F Box type Steel windows with double shutters (inside for wiremesh & out side for glass), incl guard bar,hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including two coats of synthetic enamel paint over one coat of red oxide complete all as specified and directed

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain PVC sheets for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail penelling of plain colour PVC sheetto be fitted in the MS frame welded/sealed to the styles and rails with suitablePVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawings complete all as specified and directed

Supply and fix for PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and as directed.

S & F 35mm thick, flush shutters, solid core construction, with block board core and plywood face panels, with 2mm decorative laminates on both sides of the shutters complete including applying french polish on the doors complete all as specified and directed by Engr-in-Charge

M & L for 35mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass ,gauge etc ( without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8 clause 8.24(a), supplied and fitted to chowkats complete all as specified and directed

M & L for Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm dia and fixed with tinned tacks or galvanised mild steel staples complete all as specified and directed

M & L for Sheet glass 3.00mm thick ordinary quality and glazing with oil putty complete all as specified and directed.

Same all as per item No 19 but pin head type glass complete all as specified and directed

M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed

M & L for Glazed ceramic colored tiles 300mmx450mmx 6 to 7mm thick,as in patches in vertical surfaces such as dado, skirting, wall etc set & jointed in neat cement slurry and pointed with coloured cement to match with tiles in over and including 10mm thick cement plaster in cement mortar 1:4. including dismantaling/demolation/Taking down Note:- Rates also includes in this item for necessary raking, circular cutting or notching and waste on tiles

S & F Extruded aluminium alloy handles fabricated type anodised of size 125mm long complete all as specified and directed

S & F MS 300 mm ordinary rat rails rod pattern door springs including roller and roller plate complete all as specified and directed

S& F Floor door stopper of aluminium alloy body and tongue ,anodised ,with hard drawn steel spring ,fixed in floor overall length of cover plate 140mm complete all as specified and directed

S& F 300mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed

S & F 200mm Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F 18/19mm thick solid PVC board prelaminated one side and other side plain as in board/shelves/kitchen cabinate ( Board must be water proofing ,termite proof) . complete all as specified and directed

M & L for Brick work with sub class “B” bricks straight or curved on plan exc 6m mean radius build in CM 1:6 using all as specified using old size bricks

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement with Water proffing compound all as specified (WPC measure and pais saperately)complete all as specified and directed by Engineer-in-Charge.

M&L for Rendering 5 mm thick in CM (1:3) on ceiling finished even and smooth without using extra cement including two coat of white wash on ceiling including preparation of surface complete all as specified and directed

Supply only Liquid water proofing compound.complete all as specified and directed by Engineer-in-Charge.

Taking down existing cement plaster of any description over damaged surfaces irregular facia, chajjas and in similar work and also for narrow width etc and rendering dubbing coat 15mm thick cement plaster in CM (1:4) over a coat of cement slurry @ 3.00 Kg/Sqm making surface even ( avg 50mm thick PCC 1:2:4 type B-1 using 20mm crushed stone aggregate shall be provided wherever required) followed by 05mm thick rendering in CM (1:3) finished complete all as specified and directed including two coats of cement base paint over a coat of primer over new plaster surface including preparation etc complete.(after curing of specified time and drying the surfaces as required).complete all as specified and directed by Engineer-in-Charge.

M & L for Applying two coat of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description, not otherwise described over 10 cm width or girth including preparation of surfaces complete all as specified and directed

M & L for Preparation of Complete removal of existing treatment preparing old plastered surfaces of walls and applying Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work over a coat of wall care putty 3mm thickcomplete all as specified and directed

M & L for Preparation of newly plastered surfces of walls and applying Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work over a coat of wall care putty 3mm thick complete all as specified and directed by Engineer-in-Charge.

M & L preparing new plastered surfaces of walls and applying Finishing of wall with acrylic smooth exterior paint of required paint of required shade new work (two or more coat applied @ 1.67ltr/10Sqm and including priming coat of exterior primer applied @ 2.2 Kg/10 Sqm) complete all as specified and directed

M & L for complete removal of existing trreatment preparing old plastered surfaces of walls and applying Finishing of wall with acrylic smooth exterior paint of required paint of required shade new work (two or more coat applied @ 1.67ltr/10Sqm and including priming coat of exterior primer applied @ 2.2 Kg/10 Sqm). complete all as specified and directed by Engineer-in-Charge.

M & L for Preparation of newly plastered surfces of Ceiling and applying two coats of oil bound distemper over a coat of wall care putty 3mm thick complete all as specified and directed

M & L for Preparation of Complete removal of existing trreatment preparing old plastered surfaces of Ceiling and applying two coats of oil bound distemper over a coat of wall care putty 3mm thick complete all as specified and directed

M&L for preparing of new untreated steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed by engineer-in-charge

M&L for PCC 1:2:4 type B-1 (20mm graded aggregate ) 25mm thick as in Sub base floor complete all as specified and directed by Engineer-in-Charge.

M&L for Machine cut kota stone flooring 18 -22 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) (Each stone not less than 55 cms x 55 cms) over 15mm thick screed bed in CM ( 1:4) as in floor finished.complete all as specified and directed by Engineer-in-Charge.

M&L for Machine cut kota stone slab 18-22mm thick in skirting, dado and pillars, risers of steps laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) over 15 mm thick rendering in CM ( 1:4) including taking out of existing dado complete all as specified and directed

M&L PCC 1:2:4 type B-1 as in benching, coping etc and similar items including weathering slightly rounded or chamfered angles and throating on top of roof, chajjas, rails, cills etc complete all as specified and directed

M& L PCC 1:3:6 C-1 (using 20mm graded crushed stone aggregate) as in plinth protection (75mm thick ) finished even and fair complete all as specified and directed

M& L RCC 1:2:4 type B-1 ( using 20mm graded crushed stoneagg) as in chajjas, shelves and similar items complete all as specified and directed

M & L for Providing 75mm thick precast reinforced cement concrete slab 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) and set in CM 1:4 .complete all as specified and directed by Engineer-in-Charge. ( NOTE : (reinforcement shall be measured and paid for separately).

M & L Form work to chajjas, shelves ,troughs and similar items including edges.for rough finished surfaces complete all as specified and directed by Engineer-in-Charge.

M& L TMT bars 10mm dia and over cut to lengths bent to shape required including cranking bending and spirally hoping for columns hooking ends and binding with MS wire annealed n.less then 0.90mm dia.complete all as specified and directed by Engineer-in-Charge.

All as per item No 51 above but 6mm to 8mm dia complete all as specified and directed

S&F of framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed by Engineer-in-Charge.

S/F in repairs to rotational moulded vertical water storage tanks three layer white in colour with closed tops (cylinderical ) hoisted and fixed in position 1000 ltr capacity incl disconnecting and refixing the existing GI fitting and pipe complete all as directed.

Taking down steel tubing and connections including removing removing from site of 15mm bore pipe all as specified and directed by Engineer-in-charge

All as above item no. 56 but 20mm bore complete all as specified and directed

M&L 15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs.complete all as specified and directed by Engineer-in-Charge.

M& L 20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs.complete all as specified and directed by Engineer-in-Charge.

M& L Shower rose brass chrominium plated 125mm size complete all as specified and directed.

M& L 15mm bore fancy type bib tap brass CP (Long body) with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.

S/F in repairs 15 mm dia wall Bend mixer brass chromium plated fixed to existing pipe/connections cluding telephonic hand shower and all necessary fittings all as specified and directed by Engr In Charge

S&F Cast copper alloy CP angle Valve fancy type screwed both ends for iron pipe 15mm dia/ bore of pipe complete all as specified and directed by Engineer-in-Charge.

S/F in repairs 15mm dia PVC Connection 600 mm long with 2 nos brass check nuts suitable for 15 mm bore of pipe with washers complete all as specified.

M& L Soap dish with including chromium plated brass screws and wooden/plastic cleats ( Minimum weight 105gm).complete all as specified and directed by Engineer-in-Charge.

Supply only CP Towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed

M& L Vitreous china wash down closet pan (Pedestal pattern) white with ‘S’&'P' trap plastic seat cover white including connection to out going pipe & to flushing pipe, anti syphonage pipe etc complete all as specified and directed by Engineer-in-charge (including making good to floor and fixing in repairs) excluding flushing cistern & flush pipe complete all as specified and directed by Engineer-in-Charge.

S & F in Vitreous china squatting pan “Orrisa” pattern of size 580mm “White” with 'P' or 'S' Trapfront or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe), connection to trap and to flushing pipe anti- syphonage pipe etc complete making good complete all as specified and as directed by Engineer-in-charge

S & F in repairs,PVC valve less symphonic action type, flushing cistern, low level, white of capacity 10 ltrs with inlet , ball valve, float and and fixing arrangement complete all as specified and directed by Engineer-in-Charge.

Demolition and breaking up 150mm dia drain pipes (Salt glazed ware, AC or reinforced concrete ) and set in cement mortar all as spd and directed by Engr in Charge.

M & L for Concrete bed to drain pipes laid in trenches including packing under and haunching against the sides of pipes aftaer they are laid and tested in cement concrete 1:4:8 type D-2, using 40mm graded crushed stone aggregate for 150mm bore pipe, complete all as specified and as directed by Engr in charge.

M & L for Salt -Glazed stoneware drain pipes 150 mm dia laind in trenches and jointed complete all as spd and directed

M & L for Cutting into existing manhole for connecting new drains and making good to pipes and rendering cutting out existing benching for and forming branching for and forming branch channel (1/2 round or ¼ section ) in PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate smooth finished and reforming benching as specified and directed for 150mm dia of pipe complete all as specified.

Dismantling cast-iron/PVC pipes including fittings taking out of trenches or walls as required dia of pipe upto 100mm.complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) pipes single socketed Type A in any length with rubber ring joints fixed to walls for 110mm bore.complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) pipes single socketed Type A in any length with rubber ring joints fixed to walls for 75mm bore.complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) Bends any radius for 110mm bore.complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) Bends any rcomplete all as specified and directed by Engineer-in-Charge.adius for 75mm bore with oval access door.complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) Branch pieces single( Single Y) equal or unequal) for 110mm bore with oval access doors.complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) Branch pieces single ( Single Y) equal or unequal for 75mm bore with oval access doors.complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) vent cowl 75mm complete all as specified and directed by Engineer-in-Charge.

Taking down existing old tarfelt, bituminous compound including cleaning and removing debris to a distance exc 100m n.exc 250m complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B-0 (20mm graded aggregate ) 50mm thick as in padding finished even and smooth witout using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for water proofing treatment to sunken portition / roof etc. in following sequence:- (i) Properly cleaning and drying the surface (ii) Applying a coat of bitumen primer @ 1.2Kg/Sqm and primer shall be allowed to dry over night. (iii) Laying APP based modified water proofing membrane of weight not less than 3kg per sqm and thickness not less than 3 mm, with 100mm overlaps, sealed and bonded to the surface by 'torchon' method (iv) Applying two coat of bituminous based aluminum painting @ 0.15 kg/Sqm each coat on water proofing treatment with preparation of surfaces complete all as specified and directed at site.

M & L for Vitreous china wash basin white flat back size 550 x 400mm incl waste pipe chain plugs and 32mm dia bore CP coupling complete as in repairs including a pair of bracket. complete all as specified and directed by Engr-in-Charge.

M & L for Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300 grams)complete all as specified and directed by Engr-in-Charge.

M & L for PCC 1:4:8 D-2 (using 40mm graded crushed stone aggregate) as a sub base to chequred tile ( 75mm thick ) finished even and rough.complete all as specified and directed by Engr-in-Charge.

M & L for 20mm thick screed or screed bedding in cement mortar 1:4 as a sub base to interlocking tile complete all as specified and directed by Engr-in-Charge.

M & L for Cement concrete chequered tiles of size 30 cm x 30 cm x 25 mm thick, set, jointed and pointed in neat cement slurry (with grey cement and pigment) as in floors complete all as specified and directed.

M&L for 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement.complete all as specified and directed by Engr-in-Charge.

M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

S&F in repairs 20 to 25mm external dia drapery rods stain less steel with incuding designer lattos and brackets all as specified and approved by Engr In charge including taking out old pelmet with curtain rods complete all as specified and directed by Engr-in-Charge.

S&F Health faucet CP for with 1.00 mtr long pvc pipe incl necessary GI fittings as required like tee, nipple etc all as specified and directed.

M & L for Precast cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in manhole/drain slab cover all as specified and set in CM 1:4 complete all as specified.

M&L for Treatment of soil under existing floors using emulsion @ one litre per hole , 300mm aoart including drilling and plugging 12 mm dia holes with cement mortor 1:2 (01 cement : 2 coarse sand) to math the existing floors all as specifed and as directed

M&L for ATT along the external wall below concrete or masonry apron using chemical emulsion @2.25 litre per linear metre including drilling and plugging holes etc in apron complete all as specified and directed by Engr-in-Charge.

Excavating in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 Cum, getting out, reterning filling and ramming earth or broken rubber mixed with earth around in layers not exceeing 25 cm, watering and removing surplus soil to a distance not exc. 50m and making good surface complete all as specified and directed.

S & F steel work in tubular trussles,purlins,rafters,tubler column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washers etc. complete using ERW or induction butt welded tubes confirming to Fe 410W grade E 250 quality B, etc complete all as specified and directed.

S & F 0.50mm thick (including coated thickness) Pre-colour, pre-profiled ( Galvalume ) sheets of required colour and design having tensile strength of 550 Mpa as in roof, wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer/ profile maker instruction complete all as specified and directed.

Surface excavation n.exc 30cm deep and avg 15 cm deep and getting out any type of soil.complete all as specified and directed by Engineer-in-Charge.

M/L 75 thick mm Cement concrete Type C2 1:3:6 (using 40 mm gr complete all as specified and directed by Engineer-in-Charge.aded stone aggregate) in sub base flooring complete all as specified and directed

M & L for Plain cement concrete machine pressed, precast inter locking coloured,glazed (rubber moulded) paver blocks M-40 grade, any shape & size 80mm thick with grey cement & pigment laid over sand cushioning complete as directed.Note : Sand cushioning shall be measured and paid separately.

M&L for 25 mm thick sand cushioning for interlocking paver blocks including spreading and consolidating complete all as specified and directed. Note: (i) Sand shall be coarse sand as specified. (ii) Punned down thickness shall be considered for measurement and payment.

M&L Hard core of gauze n.exc 63mm deposited spreaded and leveled in layers n.exc 15cm thick, watered and rolled/rammed to a true surface. complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:4:8 Type D-2 (using 40mm graded Agg) as in foundations, filling and mass concrete all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in sunken portion, padding work on roof, subbase, etc complete all as specified and as directed.

M&L for rendering 10mm thick in CM 1:4 on roof suraces with liquid water proofing compound @ 200 ml per bag finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for vitrified light shade floor tiles 10mm thick (square or rectangular) area of each tile not exceeding 0.36 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface with and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

All as per item no 110 above but as in skirting/ dado etc with and including 10mm thik backing coat in cement mortar 1:4 an wall complete all as specified and directed.

S&F aluminium power coated door shutters (sliding/openable/fixed (as per required at site) , aluminium section weighing 0.55 Kg/m including necesssary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door, pad lock, hinges, anodised aluminium snap beading screws etc complete all as specified and directed by Engineer-in-Charge.

S&F double action floor spring hudraulically regulated made up of min 1.25mm thick alluminium alloy sheet foundation box, main body with stailess steel cover governing pivot made of brass other made of mild steel heavy duty, complete all as specified and directed.

S&F for sheet glass palin/coloured (as per directed by Engr-in-charge) 5.5 mm thick best quality and glazing with rubber packing, screws or glass putty in squares exc 0.5 Sqm each pane complete all specified.

S&F PVC hollow profile 9/12mm thickness design and pattern as approved/directed at site complete all as specified and as directed.

S&F of aluminium power coated shutters for cubboard and office cabinet work with necesarry openning, aluminium section weighing not less than 0.55 kg/m including necessary locking arrangement,guide wheels, joining cleats, glazing clips, powder coated aluminium snap beading screws etc complete all specified and directed.

S & F in repairs false ceiling at all heights with GRG (Glass fibre Reinforced Gypsum) false ceiling tiles of size 595x595mm of approved texture, design and patterns having moisture content less than 2% humidity resistance of 99% NRCO.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (min) to be laid in true horizontal level suspended on inter locking metal T-grid of hot dipped galvanized iron section of 0.33mm thick ( galvanized @ 12a grams per sqm incl both sides ) comprising of main T runners of size 15x32mm of length 3000mm, cross T of size 15x32mm of length 1200mm and secondary intermediate cross T of size 15x32mm of length 600mm to form grid module of size 600x600mm, suspended from ceiling usung galvanized mild steel items (galvanizing @ 80 grams per Sqm) ie 50mm long 8mm outer diater M-6 dash fasteners 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall / partition with the help

Dismantling steel sheeting, any gauge, thickness, including Nainital or similar pattern (plain or corrugated) in roof coverings including ridges, eaves etc complete all as specified and directed.

S & F pre - painted galvalume aluminium zinc coating plain sheeting 0.50 mm thick of required colour and shape having tensile strength of 550 Mpa as in ridge valley,gutters,barge board,roof covering / cladding to wall, fixed with self tapping screwes complete all as specified and directed.

Supply and fix suspended ceiling of plaster of paris 12.5 mm thick which include GI perimeter channel of size 20 x 27 x30x0.5 mm thick along perimeter of ceiling screwed/fixed to brick wall or existing supports at 610 mm centre to centre suspending GI intermediate channel of size 15x.15x0.9mm thick from the slit at 610 mm centre with ceiling angle (GI) of size 25 x 10x0.55mm thick fixed to the sollit with GI cleat 0.5 mm thick having knurted web of 51.5mm and two flanges of size 26mm each with lips of 10.50 mm fixed to the intermediated channel with the help of connecting clip and in the direction perpendicular to the intermediate channel at 300 mm centres, POP ceiling boards of size 1220mm width x 12.5 mm thick screwed to ceiling section with 25 mm long wass screw @ 230mm centres, screw fixed mechanically either with screw driver or drilling machine with suitable attachment. Ceiling shall be sealed at joints and finished with jointing compound etc complete including finishing the exposed surfaces of false ceiling with two coats of plastic emulsion paint over a coat of primer complete all as specified and directed

S & F 5mm thick Printed PVC sheet used instead of plain colour PVC shectplain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site. complete all as specified and directed

S&F 12mm thick toughened or tampered glass (tuffen glass) thermal and chemical treated with heavy strength of fine polished edge as in doors with SS long body handle, pivots, floor springs and locking arrangements of heavy duty accessories. It made from annealed glass via a thermal tempering process and toughening process. The glass compressive strength should be minimum 69 mps itching and cluster work as per sample kept in GE's office complete all as specified and directed by manufacturer's instruction and Engineer-In-Charge.

S&Fpowder coated aluminium window and ventilator shutters, sliding/openable/fixed (as per required at site) type without sash bar, alu section weighing 0.55 kg/m, including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised alu snap beading screws etc complete all specifiedand directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation or etc, for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in hard dence soil, complete all as specified and directed.

Removing excavated material (soil) to a distance not. exc. 50 mtr and depositing where directed at a level nexc 1.5 mtr above the starting point complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregatre as in surface channels and drains complete all as specified and directed.

M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms moulds, mitred/stopped ends etc complete all as specified and directed.

M & L for preparing new plastered surface and applying three coat of white wash complete all as specified and directed.

SCHEDULE ‘A’ PART-II ( LIST OF E/M WORKS AT NAGROTA) Taking down carefully unserviceable Aluminium point wiring complete (light, fan socket, bell or power) with fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings etc. and keeping in safe custedy for taking credit all as specified and as directed by Engr-in-Charge

Taking down ceiling fan//Exhaust fan / Wall mounting fan any sweep, removing blades ,cleaning the fan completely for dust and dirt, oiling & greasing and hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook, rubber pad, nut bolts and washers etc, complete, all as specified and directed by Engr-In-Charge.

M&L for Concealed Point wiring for modular switches using FRLS PVC insulated unsheathed multi strand copper conductor cable 1100 volt garde 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed multi strand copper conductor earth wire drawn in and including PVC conduit medium grade ISI marked not less than 20 mm dia concealed in wall & surface on ceiling with all conduit fittings etc terminated in concealed pressed steel sunken box for fixing switches , sockets , fan regulators etc incl testing and making good to disturbed surface to match existing surface for one light/fan/bell point complete all as specified and directed.

All as per Srl item No.131 above but for one socket out let 5Amp controlled by one switch on same board with other switch . compete all as specified and directed

All as per Srl item No 131 above for one socket out let 5 Amp controlled by one switch on independent board with other switch . compete all as specified and directed

All as per item No 131 above here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15Amp socket out let controlled by one 15Amp switch on independat board.

All as per item No 131 above here in before but point wiring with 4 sqmm FRLS multi stranded copper conductor cable for main circuit and 4 sqmm cable as earth continuity conductor for controlled by two pin and earth plug and socket complete with one Double pole MCB 32 amp 240V

S & F Modular snap switch SP one way 5/6 Amps suitable for 1 Module complete all as specified and directed by Engr-in-Charge.

S & F Modular socket 5 pin 5/6 Amps suitable for 2 Module complete all as specified and directed by Engr-in-Charge.

S & F Modular snap switch SP one way 15/16 Amps suitable for 1 Module complete all as specified and directed by Engr-in-Charge.

S & F Modular socket 5/6 pin 15/16 Amps suitable for 2 Module complete all as specified and directed by Engr-in-Charge.

S & F Modular Fan step Regulator electronic, 120 watts 2 Module complete all as specified and directed by Engr-in-Charge.

S & F Modular white cover plate incl Modular base frame/boxes & powder coated Modular sheet metal concealed box for 6 module complete all as specified and directed by Engr-in-Charge.

All as per Item No-141 above but 3 module

All as per Item No-141 above but 2 module

All as per Item No-141 above but 8 module

All as per Item No-141 above but 12 module

S & F Modular blanking plates 1 module complete all as specified.

S&F of ceiling rose 3 terminal complete PVC/Polycarbonate isolated boly complete all as specified and directed.

S&F for lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F LED inverter chrargeable bulb 12 watt backup to 4 to 6 housr complete all as specified and directed.

Supply & Fix sleek surface round ceiling mounted decorative down light fitting with PC cover suitable for 1 x 15 Watt complete all as specified and directed by Engr-in-Charge.

Supply and fixing warm LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED lights fitting 1x 18 W, 220V, AC connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge.

S & F LED light fitting 1X10 W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.complete all as specified and directed by Engr-in-Charge.

M&L in replacement of sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked minimum 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 sq mm as earth continuity conductor connected to commen earth and earth dolly complete all as specified and directed by Engr-in-Charge.

S&F in replacement of (VTPN) sheet metal enclosure double door for distribution board factory made for MCCBs DB load link TPN 6 way including 100 Amp MCCBs suitable for MCCB as incomer, 100 Amp,4 pole. (when MCB's are to be used) with suitable size of busbar including 100 A MCCB as incomer 16 KA complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down complete all as specified and directed by Engr-in-Charge.

S&F sheet metal enclosure double door for distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCBas incomer, 63 Amp,4 pole. (when MCB's are to be used) with suitable size of busbar including 63 A MCCB as incomer 16 KA complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down all as directed by Engr-in-Charge at site incl taking out of exsing UNSV DB with MCBs. (Note: MCCB 63 Amp 4 pole is included in the above quoted rate)

S&F sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete incl taking out existing UNSV DB with MCBs.

S&F sheet metal enclosure distribution board SPN 08 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete incl taking out existing UNSV DB with MCBs.complete all as specified and directed by Engr-in-Charge.

S&F sheet metal enclosure distribution board SPN 04 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete incl taking out existing UNSV DB with MCBs.complete all as specified and directed by Engr-in-Charge.

S&F MCB SPN 40 A to 63 A 10 KA 240 volts "C" series complete all as specified and directed by Engr-in-Charge.

S&F MCB single pole 5 to 32 Amps 10 KA 240 volts "C" series complete all as specified and directed by Engr-in-Charge.

S&F building security light luminaries energy saving and envirnment friendly long life LED light of 25W made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 protection and Impact resistanve of IK07, including MS Bracket light grade 25 mm dia, 1.2 m long bend in shape fixed on wall having an angle 120 degree, fixed with and suitable size nuts, bolts and washers etc including taking down of existing light fitting and complete ,all as specified and directed.

M&L for sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 sq mm as earth continuity conductor connected to commen earth and earth dolly complete incl taking out existing UNSV service connections.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sq. mm 2 core nominal cross section in service connections

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 25 Sqmm 4 core, complete all as specified and directed by Engineer-in-Charge

Excavation in trenches in any type of soil not exc 1.5 mtr in depth and 1.5 mtr wide and getting out for laying of cables complete all as specified and directed by Engr-in-Charge..

Returning and filling in including spreading, leveling , watering and well ramming in layers not exceeding 25 cm thick excavated earth complete all as specified and directed.

Removal of surplus soil to a distance not exceeding 50 mtr and depositing at a level not exceeding 1.5 mtrs above the starting point complete all as specified and directed.

M&L for well burned bricks , laid flat ( old size) sub class B designation '75' for cable protection copmplete all as specifed and directed.

M&L for Sand cushioning to under ground cable laid in trenches for laying of LT UG cables 8 cm depth before laying the cable and 15 cm after laying and punned down to a depth of 10 cm as per MES SSR Part-I (2009) complete all as specified and directed by Engr-in-Charge. Note: Punned thickness shall be measured and paid to the contractor.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion complete.

Supply and installation of advanced maintenance free tripod ring earthing system for boring the required no of holes in semi hard soil or hard soil consisting of 03 (Three) Nos, UL467 listed and CPRI attested copper bonding high tensil low carbon steel core electrode of 17.2 mm with a minimum coating thickness of 250 microns and length of 3 meter tested according IEC625612 with minimum 10 Yr of life span (the road should be marked as per the UL certificate) model AGE PALI with down side GI plate (1 ft x 1 ft) attached with GI 40 mm tubes as outer covered of electrode internally and externally covered with compound minimum 3 x 25 Kg / Electrode of earth enhancing compound for the earth pit electrode in 1 Tripod earthing. The endancing compound should have resistivity less then 0.5 ohm meter with chemically insert to sub soil that should not pollute the environment and non-corrosive the the earth electrode it self.tripod earthing connected 25x3 Copper trip. NOTE :- Tested Central Power Research Institute (CPRI) measurement of earthing resistance of ASHGEL Earthing Electrode, Short Time Current and Nabl Chemical ASHGEL

M & L for Earthing complete with galvanised mild steel earth plate electrode 60cm x 60cm x 6mm thick, burried directly in ground prefarably in vertical position (Earth pit not less than 2.25 mtr below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level, connected to galvanised iron strip 25x4 mm by means of bolts, nuts, check and washers of galvanised iron including pit of PCC (1:2:4) type B-1, pre cast RCC cover slab of size 550x550x75 mm, XPM reinforced not less than 1.60 Kg/Sqm with suitable built in handle made from 12 mm dia MS round bar, excavation and earth in any type of soil., 20 mm dia bore medium grade galvanised iron water tubing fixed with cast iron funnel and wire mesh at one end, 15mm bore light grade galvanised iron protection pipe for earth lead wire upto 5 m length, charcoal, common salt complete all as shown in electric plate No 5 of SSR 2009 Part I connected to equipment, testing on completion, complete all as specified and directed.

Supply and fixing in repair of aluminium strip 25 x 3.15 mm with saddles and fixing screws etc, for roof conductors and down conductors above ground, complete all as specified and directed.

S &F Air termination, sigle pointed aluminium rod 12 mm dia and 300 mm long complete all as specified and directed by Engr-in-Charge.

Supply and fixing test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including 3 Nos 8 mm dia 25 mm long hex, head scew all as specified and directed by Engr-in-Charge.

Supply and laying in trenches/on piller/on wall GI water tubing 20 mm bore dia medium grade ISI marked with all fitting (such as tee,elbow,socket,union,short, pieces) including testing etc. complete all as specified and directed. Note:(Exacavation and earth work shall be measured and paid separately)

S & F Gunmetal globe (Class 2) or gate valves (brass insert),with iron wheel head screwed both ends for iron pipe size 20 mm dia complete all as specified and directed by Engr-in-Charge.

M & L for Cutting of existing pipe laid any size dia for inserting Tees for new connection of 20 mm dia all as specified and directed by Engr-in - charge

S & F of Havells IP40 Solution with Insulated Plug and Socket 16 A - 32 A with C16 MCB (IGPS Socket and plug top cat Part No DHDPBDP032

S&F sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete all as specified and directed by Engr-in-Charge.

S&F Fire alarm control panel complying with BSEN 54 Single loop panel of capacity from 99 detectors & 99 modules upto 200 detector and including with 2x12V / 12 AH battery back to system for continuous operation complete all as specified and directed.

S&F 1.5 Sqmm FRLS stranded copper conductor 2 core with 1.00 as each wire, 1100 volt wiring in stove enamelled steel conduit with all fittings for fire alarm system complete all as specified and directed.

Supply and fixing of detectors Complying with and type certified to EN - 45 Addressable type smoke detector Photoelectric /Optical with base with self built intelligence as per IS: 11360 complete all as specified and directed by Engr-in-Charge.

Supply, assembling , erection, testing and commissioning of addressable input/ Monitor module, complete all as specified and directed.

Supply, installation, testing and commissioning of intelligent addressable manual call point esettble type with built in fault isolator for installtion inside buildings complete with and including base mounting box, cable glands and installtion hardware, compete all as specified and directed.

Supply, installation, testing and commissioning of intelligent addressable fire alarm hooter cum stobe with built in fault isolators for indoor application complete with including base mounting box, cable glands and installation hardwares, complete all as specified and directed.

Supply, fixing and testing of short ckt isolator complete all as specified and directed.

S&F , testing and commissioning response indicator complete all as specified and directed.

S& F Fire Alarm Sounders / Sirens Electronic type horizontal single stage continous normal operation for atleast 50 minutes with sound level 65 DB to 120 DB measured at 1.5 Mtr with sound output variation of + 5 DB upto 1000 mtr range complete all as specified and directed by Engr-in-Charge.

M/S MANISHA BUILDERS (BID ID -3140304)

M/S Shankardass Devidass (BID ID -3145657)

ASHWANI KUMAR KHAJURIA AND SONS (BID ID -3140066)

M/S KALSI ENGINEERS AND CONTRACTORS (BID ID -3146802)