PROVN OF DEFICIENT SINGLE LIVING IN ACCN AT SNCOS MESS AT AF STN DADRI UNDER AOR OF GE (AF) FARIDABAD

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for laying cables, poles, shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

All as per above item No 1 but depth exc 1.5m but n exc 3.00 m.

Surface excavation not exc 30 cm deep and averaging 15 Cm deep and getting out in soft/soose soil complete all as specified and directed.

Removal of surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base, foundation, filling in mass concrete etc complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

M & L brick work with Fly ash bricks straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) with and including weep holes in brick work, complete all as specified and directed .

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases od columns , raft and raft beams , sides and soffits of foundation and plinth beams and similar work vertical or better for rough finished surfaces of concrete complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)complete all as specified and directed.

Formwork to staircase with sloping or stepped soffits including risers and stringers (excluding landing), complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges in rough finished flat surface of concrete complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, bands, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

Form work to pillars, posts, struts, piers, columns and stachions with rough finished, square, rectangular or polygonal concrete surfaces complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (20 mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (20 mm graded stone aggregate) in Slabs supported on walls, beams and col-umns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (20 mm graded stone aggregate) as in Chhaja complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (20 mm graded stone aggregate) in Beams, cantilevers, bressummers complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (20 mm graded stone aggregate) in Columns, pillars,piers,posts and struts complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick or concrete surfaces in cement plaster 1:6 and finished even and smooth (without using extra cement), complete all as specified and directed.

Supply only integral water proofing compound conforming to IS-2645-1975 complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement plaster 1:4 using WPC 3% by weight of cement (WPC to be measured and paid separately) and finished even and smooth (without using extra cement), complete all as specified and directed.

M & L for plain cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate, as in lintels upto 1.5 m clear span, cills, steps,seismic and other similar bands, plinth course, string courses, lacinng courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M&L for 75 mm thick cement concrete type C-1, 1:3:6 using 20mm graded stone aggregate finishing surface even and smooth without using extra cement as in plinth protection laid in panels including mastic filling complete all as specified and directed.

M&L for Hard core of gauge n exc 63mm thick of broken boulder spread leveling watering ramming to true surface complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate, complete all as specified and directed.

M&L for coloured, printed, Non-skid ceramic tiles, coloured, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed.

M&L, First quality glazed ceramic coloured tiles of (450x300 mm) x 7 mm thick, laid on vertical surfaces such as skirting, dados and risers to steps etc laid over and including 10 mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement to match the shade of tiles ,complete all as specified and directed.

M&L for light coloured Fully Vitrified tiles of 10mm thick (square/Rectangular), polished area of each tiles n.exc 0.36 Sqm as in floor etc sat and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick cement screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for light coloured Fully Vitrified tiles of 10mm thick (square/Rectangulur), polished area of each tiles n.exc 0.36 Sqm as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for machine cut kota stone slab flooring, 20-25mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, moulding on edges and polishing, over and including 20mm thick screed bed in Cement mortar (1:4), complete all as specified and directed.

M&L for machine cut kota stone slab on risers/dados, 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, moulding on edge and polishing over and including 10mm thick rendering in Cement Mortar (1:4), complete all as specified and directed.

M&L for Granite (of any type) tiles, 20mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing over and including 20mm thick screed bed in Cement Mortar (1:4) complete all as specified and directed.

M&L for Rendering 5 mm thick cement plaster on RCC ceiling surfaces in cement mortar (1:3) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for Preparation of new surfaces of ceiling,chajja etc, including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of External emulsion paint over a coat of primer and 3mm thick wall care putty, complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of primer and 3mm thick wall care putty, complete all as specified and directed.

M&L Plain Cement concrete, type B-0, 1:2:4 using 12.5 mm graded stone aggregate on roof padding and kerbs in slope finished even and fair, complete all as specified and directed.

M&L for 15mm thick Screed bed in cement mortar 1:3 mixed with integral water proofing compound @ 3% by weight of cement, complete all as specified and directed.

M&L for laying APP modified membrane with non woven polyester reinforcement mat (concrete core) not less than 3mm thick & not less than 3.5 kg/sqm, the overlap shall be 100 mm on length side & 100 mm on width side over a tack coat of Industrial bitumen of 1.20 kg/Sqm over Bituminious based primer IS No. 3383@ 250 gms/sqm including apply of Aluminium colour synthetic enamel paint @200 gm/sqm, complete all as per manufacture's instruction complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specification and drawing complete all as specified and directed.

S&F factory made soilid panel PVC Door shutter 30mm thick (Style) consisting of frame made out MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet stripof 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, & bottom rail; Panneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F Factory made Flush shutter, 30 mm thick, solid core construction, with block board core and plywood face panels, commertial type on both sides, fitted to chowkhats of 2nd class hard wood (hollock), complete all as specified and directed.

S & F of 35 mm thick (Batten thickness) 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without shash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and sizes of the members of shutters as specified in clause No . 8.24 (a) of MES schedule part – I (Specifications - 2009), supplied and fitted to chowkhats complete all as specified and directed.

S&F for ECO 2000 series Approx size of 0.90 m x 1.20 m (Elixir/NCL SECCOLOR ) Roll framed galvanised pre painted steel section windows/ventilators including provision of grills, 5 mm thick glass and SS wiremesh specification and drawing as per CE (AF) WAC, PALAM sheet no -1/2 and 2/2 of drawing no-CEAF/STD-191/2014 etc complete all as specified and directed by Engineer-in-Charge. (a) Fixing details:- frame and shutter frame sections should be cut to lenth and miter joined with poly propylene corner brackets, mullion section should be joined with frame/mullion using nylon mullion cap, ethyl propyllene diamene monomer(EPDM) gasket should be used all around glass in shutter and fixed glass. Rubber gasket should be used aroud the fly mesh to fix mesh in mesh shutter. (b) Accessories:- Each Glazed shutter should be provided with MS powder coated friction hinges, high grade aluminium powder coateed handle -1 for each shutter (c) Glass shutters having fixed glass shall be 5 mm thick orion blue (ET725) GLASS, having U value of 3.85 W/sqm K, light transmission factor of 18% and solar radiation factor of 0.23 fo ST Gobin, HNG OR MODIGUARD (d) Windows should be provided with grill made of 10mm SQR. MS Bars welded to at 150 mm centre to centre, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws. (e) Window frame should be fixed to brick/concrete masonry by using nylons self expanding caps and driving MS electroplated 80 mm long screws into the caps through frames. (f) Mesh shutter should be provided with a stainless steel 32 gauge fly mesh of 304 grades with 144 holes per Sqr.inch.

M&L for 1.25 mm thick Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M&L for 1.25mm thick Pressed steel frames of size 165mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description , over 10 cm in width or girth not otherwise described applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete all as specified and directed.

M&L for preparation of new wooden surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of prink primer all as specified and directed.

S&F Brass chromium plated Tubular towel rail 20mm dia D type, 60 cm long between flanges complete all as specified and directed .

S&F of floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with overall length of cover plate 140 mm, complete all as specified and directed.

S&F 150 mm Aluminium handles, cast type, anodised of extruded section complete all as specified and directed.

S&F 200mm aluminium, anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed.

S&F 100mm butt hinges, medium weight, cold rolled mild steel and fixed, complete all as specified and directed.

S&F, Aluminum alloy, anodized, door bolt with hasp staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed length of bolt 250 mm, bolts not less than 16mm dia with and including a minimum of 6 bolts not,four on bolt plate and two on staple plate complete (ISI marked ) , complete all as specified and directed

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed in wooden/steel/Aluminium windows, or Stainless steel wire staples all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring into brick wall etc and making good, cutting exceeding 20cm girth, complete all as specified and directed.

S&F 15mm bore tubes 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

S&F 20mm bore tubes 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

S&F 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F 20 mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair and all as specified and directed.

S&F vitreous chinaware Wash basin, white, flat back of size 550x400 mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32 mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts and including new brackets including waste pipe of 32 mm dia , complete all as specified and directed.

S&F shower roses, brass, chromium plated with or without swivel joints 125mm size incl fixing to steel pipe, incl shower arm 15 mm size , 195 mm long with bend of 45 degree. complete all as specified and directed.

S&F PVC connection 15 mm bore 450 mm in length, complete all as specified and directed.

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws embedded in the wall all as specified and directed.

S&F PVC 110 mm (SWR) pipe, single socketed in any length with rubber ring joints fixed to walls with clamps, complete all as specified and directed.

S&F PVC 75 mm (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamps, complete all as specified and directed.

S&F PVC 75 mm (SWR) bends any radius, complete all as specified and directed.

S&F PVC 100 mm (SWR) bends any radius, complete all as specified and directed.

S&F 75 mm dia bore PVC (SWR) junction single 'T' equal or unequal, complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) junction single 'T' equal or unequal, complete all as specified and directed.

S&F tripple layer, 1000 litres capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F angle valve, 15mm dia chromium plated, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed.

S&F 15mm bore bib taps, chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F 15mm bore brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed.

S&F 15mm bore pillar tap, cast copper alloy, with capstan heads, fancy type chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F, Vitreous china wash down water closet, pedestal pattern (EWC), white, with 'P' or 'S' trap, with PVC water closet seat, black or white, closed pattern, with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F 100mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement oncrete type B-1, 1:2:4 using 20mm graded stone aggregate, complete all as specified and directed.

S&F Curtain rod, Stainless steel, 25 mm dia, 1mm thick, with pairs of fixing fancy type brackets heave grade, Fancy type supprting stops heavy grade, rollers including screws with required accessories and finishing the surface with existing wall surface etc, complete all as specified and directed

M&L for machine pressed precast interlocking paver block any shape and size conforming to IS -15658-2006 of 80mm thickness M-40 Gde with grey cement and pigment over and including 30mm thick sand cushioning complete all as directed. Note:- Sand cushoning shall be measured and paid separately.

M&L for Sand filling under floors or as in sand cusioning for interlocking paver block fixing complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 stone aggregate as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M & L for 150mm bore, reinforced cement concrete pipe class NP-3 laid and jointed with collars including fittings of same grade in trenches at any depth including jointing and testing, complete all as specified and directed. Note : (i) Excavation and earth work and concrete for bed and haunching of pipe shall be measured and paid separately.

M&L for Plain cement concrete 1:3:6 type C2 ( 40mm graded stone aggregate) as in sub base and mass concrete all as specified and as directed.

M&L for providing pre-cast reinforced cement concrete landing, cover slabs (for manholes etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:6 complete all as specified and directed

M&L for ATT treating the bottom and sides of excavation at the rate of 5 liters of emulsion per Sqm of surface area complete all as specified and directed.

M&L for ATT treating the top surface of filled earth at the rate of 5 liters of emulsion per square complete all as specified and directed.

M&L for ATT treating the soil alongwith external perimeter of building at the rate of 2.25 liter complete all as specified and directed.

M& for point wiring (concealed) in and incl rigid non-metaic PVC conduit, ISI marked 19/20 mm dia, with 1.5 sqmm PVC insulated(FRLSH) unsheathed stranded copper conductor cable, single core, 1100 volts grade with, cast iron/pressed steel terminal box of suitabe sizes & 1.6 mm thick duly painted inner & outside by anti-corrosive paint, for mounting switches, sockets, fan regulator etc with mudular cover plates and incl PVC insulated & unsheathed stranded copper conductor of 1.5 Sqmm as continious earth wire including cutting/chasing complete for the following complete all as specified and directed.

All as per item No 92 above but one light/fan/bell point controlled by one switch incl continuous earth wire for connection to fan clamp, regulator and earth dolley

All as per item No 92 above but for 3 pin 5 Amps socket on Same board .

All as per item No 92 above but for 3 pin 5 Amps socket on independent board .

All as per item No 92 above but power point wiring (concealed) with 2.5 Sqmm singe core PVC insulated (FRLSH) unsheathed cable with stranded copper conductor for one switch socket outlet, 5/15 Amps muti purpose on independent modular plate including PVC unsheathed copper conductor of same dia as earth wire complete all as directed.

M & L for Wiring for circuit/submain wiring alongwith earth wire with the following sizes of is PVC insulated (FRLSH) copper conductor, single core cable in surface/ recessed 2x4.0 sq. mm + 1x2.5 sq. mm earth wire incl PVC conduit of required size medium grade ISI marked complete all as specified and directed. Note: Two run of wiring alongwith earth wire & PVC conduit shall be measured as single run.

M&L for Wiring for circuit / submain wiring alongwith earth wire with the following sizes of is PVC insulated (FRLSH) copper conductor, single core cable in surface/ recessed 2x 6.0sqmm + 1x 4 sqmm earth wire incl PVC conduit of required size medium grade ISI marked complete all as specified and directed. Note: Two run of wiring alongwith earth wire & PVC conduit shall be measured as single run.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amps for AC complete all as specified and directed.

Supply and fixing Switch modular type,Modular switch 1 way 6A, 1 module completes all as specified and directed.

Supply and fixing Socket, 6A - 2/3 pin combined 2 module completes all as specified and directed.

Supply and fixing Socket 6A/16A - 2/3 pin combined 2 module completes all as specified and directed.

Suppy and fixing modular Fan step regulator, 120W - 2 module complete all as specified and directed.

S&F Ding Dong door bell 230 Volts , AC complete all as specified and directed.

S&F Modular Bell push flush type 5 Amps, single pole one way 230 Volts , AC complete all as specified and directed.

S&F ceiling rose 65x50 mm 3 terminal, complete all as specified and directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F White cover frame with plate - 1 module complete all as specified and directed.

S&F White cover frame with plate - 3 module complete all as specified and directed.

S&F White cover frame with plate - 8 module complete all as specified and directed.

M&L earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level,the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected toand including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES SSR part I and testing on completion including necessary excavation and earth work in any type of soil,PCC(1:3:6)type C1 chamber,pre-cast RCC slab 50mm thic in cement concrete (1:2:4),type B1,reinforced with welded steel wire fabric or XPM,(weight not less than 4 Kg per Sqm) with cast iron frame,funnel with watering pipe 20mm dia medium grade,wire mesh and lugs,GI protection pipe,15mm dia,light grade,7.5 mtr long for protection of earth lead upto test point etc complete all as specified and directed by Engineer-in-Charge.

S&F sheet metal enclousers MCB type DB suitable VTPN 4 way 200 Amp rated bus bar double door type complete all as specified and directed.

S&F sheet metal enclousers MCB type DB suitable SPN 08 way 200 Amp rated bus bar double door type complete all as specified and directed.

S&F MCCB 3 Pole .415 V. fixed type, 25 to 100 Amps with breaking capacity 16 KA , 240 V complete all as specified and directed.

S&F MCB SPN capacity 32 Amps , 240 V complete all as specified and directed.

S&F MCB SP capacity 6-32 Amps , 240 V complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix water heater storage type ( geyser) electric , capacity 25 Ltrs BEE 5 Star rated complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3½ core complete all as specified and directed.

M&L for sand cushioning with a layer of sand, 80mm thick before laying of cable and 150mm thick after laying of cable to trenches, complete all as specified and directed.

M&L for brick sub class 'B' , size 230mm x 115mm x 75mm and laid in trenches as in protection of UG cables complete all as specified and directed.

M&L for boring of holes under road pavement, motor hardstanding by trenchless technology using ultra sound technicque and necessary machine including HDPE pipe of 150 mm dia suitable foor 40 MPA working pressure. complete all as specified and directed.

Supply and lay pipe galvanized, “Medium grade including fittings 40 mm dia complete all as specified and directed .

Supply and fix for 40mm dia pipe Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and for 20mm dia pipe Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

M&L for drilling and tapping existing castiron pipe for for branch connection for 20mm dia GI pipe including necessary excavation and earth work etc complete all as directed.

Singh Associates (BID ID -3188165)

J S CONSTRUCTION CO (BID ID -3189116)

36SHRI RADHEY ASSOCIATES (BID ID -3188648)

GARG CONSTRUCTION CO (BID ID -3189350)