Loading
Loading…
Loading…
Tender Value
₹1.1 Cr
EMD Value
₹2.1 L
Closing Date
4 May 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
SIGNAL
14 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less, where:- V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. Client certificate from other than Govt Organization should be duly supported by Form 16A/26AS generated through TRACES of Income Tax Department of India.
(a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Similar nature of work -"Any Signalling work"
26 conditions · 7 needing a document upload
Statement of Deviation
Power of Attorney
Certificate to be submitted / uploaded by tenderer along with the tender documents (Annexure V), Part I of GCC.
Annexure-V(A), Part I of GCC (This certificate is to be given by attorney/authorized signatory/each member of Partnership firm/Joint Venture (JV)/Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.)
(Bid Security) Bank Guarantee Bond from any scheduled commercial bank of India (Annexure VI(A)
EMD Submitted
Copy of PAN card
Documents for Turnover for financial eligibility criteria
Documents for technical eligibility criteria - Performance certificates for single similar nature of work
NEFT Details
GST Registration Certificate Copy
Bid Security Declaration in lieu of EMD Submitted
Organization details
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less, where:- V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. Client certificate from other than Govt Organization should be duly supported by Form 16A/26AS generated through TRACES of Income Tax Department of India.
Power of Attorney
Annexure-V(A), Part I of GCC (This certificate is to be given by attorney/authorized signatory/each member of Partnership firm/Joint Venture (JV)/Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.)
(Bid Security) Bank Guarantee Bond from any scheduled commercial bank of India (Annexure VI(A)
NEFT Details
Copy of PAN card
Organization details
GST REGISTRATION/ A CERTIFCATE FOR NON-APPLICABILITY OF GST REGISTRATION
Bid Security Declaration in lieu of EMD Submitted
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Signaling and Telecommunication portion of work in connection with various engineering works in CGL-AJJ Section over Chennai division
M-SG-2026-508-CGL-AJJ
M-SG-2026-508-CGL-AJJ
Open
Works - General
12 Months
Chennai, Tamil Nadu
₹0
₹2.1 L
4 May 2026
10 Apr 2026
20 Apr 2026
67 items across 1 schedule · ₹57,15,432.38 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Supply of earth electrodes (GI) a s per Drg no SG/CN/02/13 | Numbers 41.00 | — | 1,618.75 | 66,368.75 |
| 2 | Provision of earth electrodes as per drawing No.SG/CN/02/13 and earthing of metallic sheath and armour of all cables in all apparatus cases, relay room, equipment room, SM's room for block and control, and earthing of all equipments in apparatus cases, power room, relay rack, cable termination rack, control panel, signals, lever frames with MS flat 35mm X 6mm/19c cable (MS flat for closer by areas and MS flat/19c cable combination for farther areas) as per the instructions of Railway representative at site. The work includes painting of earth resistance value on the earth pit. (Supply of 19C cable is not covered in the scope of this schedule). [MS flat for earthing 35mm X 6mm, cement, GI earth electrodes, common salt, charcoal, country bricks, M sand, soldering materials and all other miscellaneous materials required for the work shall be supplied by the Contractor]. | Numbers 41.00 | — | 1,707.55 | 70,009.55 |
| 3 | Supply of 24 Core x 1.5 Sq.mm PVC insulated Armoured, unscreened underground Railway Signalling copper cable as per IRS: S-63/2014 REV.4 | Metre 2000.00 | — | 388.15 | 7,76,300 |
| 4 | S u p p l y o f 1 2 C x 1 . 5 S Q M M P V C insulated Armoured, unscreened underground Railway Signalling copper cable as per IRS: S-63/2014 REV.4 | Metre 2000.00 | — | 215.92 | 4,31,840 |
| 5 | " S u p p l y o f 2 x 2 . 5 s q . m m P V C insulated Armoured, unscreened, underground Railway S i g n a l l i n g C o p p e r c a b l e a s p e r spec IRS.S.63/2014(Rev.4.0) or latest" | Metre 1000.00 | — | 98.76 | 98,760 |
| 6 | Supply of 1x10 Sq.mm (140/0.30mm) Flexible Annealed P u r e Copper (APC) PVC Insulated Unsheathed Single Core Cable as per IRS:S: 76/89 with all latest amendments | Metre 500.00 | — | 143.15 | 71,575 |
| 7 | Supply of 16 Sq.mm multistrand Flexible APC PVC insulated copper cable as per IS 694 | Metre 75.00 | — | 228.14 | 17,110.5 |
| 8 | Supply o f Underground jelly filled 6 QUAD, 0.9MM Dia as per spec IRS:TC 30-05 with amd 5 or latest | Metre 1000.00 | — | 301.05 | 3,01,050 |
| 9 | Supply of 48 Fibre armoured OFC cable as per R D S O Specification RDSO/SPN/TC/110/2020 Rev. 0 or latest | Metre 3000.00 | — | 126.32 | 3,78,960 |
| 10 | S u p p l y o f P o ly t h e n e In s u la t e d Polythene Sheathed armoured J e l l y Fi l l e d Telephone Cable with Poly-AL Moisture Barrier, 10 Pairs, 0.63 MM Conductor Diameter as per RDSOSpecification N o . IRS:TC-41/97 with amendment 1 or latest | Metre 1000.00 | — | 123.9 | 1,23,900 |
| 11 | Supply of UTP Cable /CAT6/6A cable ETL or UL or CE3P certified panduit or Systimax or R&M or AMP or Molex or Krone Or D-LinkMakes | Metre 305.00 | — | 34.73 | 10,592.65 |
| 12 | Supply a n d fi x i n g o f 2 0 p a i r C T b o x and termination of cables | Numbers 4.00 | — | 4,761.16 | 19,044.64 |
| 13 | Supply a n d provision o f normal joint using Thermo shrink jointing k i t (RDSO specs No TC/77/2012 ( Rev.3) with amendment No.1&2 o r latest.& jointing k i t t o be inspected by RDSO) f o r 4 / 6 quad cable normal joint. The work includes excavation of joint p i t o f size 1mX1.5mX1.5m and closing t h e s a m e after completion of cable joint as per the instruction of Railway representative at site. | Numbers 6.00 | — | 4,628.91 | 27,773.46 |
| 14 | S u p p l y a n d installation o f 4 8 fi b r e Joint enclosure f o r armoured optical fi b r e cable c o n f o r m i n g to RDSO spec.RDSO/SPN/TC/68/2014 rev2.1 or latest | Numbers 6.00 | — | 20,060 | 1,20,360 |
| 15 | Excavation of cable trench in all kinds of soil except hard rocky areas including clearing of roots of trees, rocks, bushes etc. to a depth of 1.0 Mtrs and to a width of 0.3 Mtrs. (Laying of cables is not included in this schedule) | Metre 2900.00 | — | 64.1 | 1,85,890 |
| 16 | Excavation of trench to a depth of 1 Mtr. for track crossing of cables, refilling of trench by ramming a n d consolidating i t a s p e r the instructions of Railway representative at site a f t e r l a y i n g o f D W C / RC C p i p e s . During excavation of trench, it has to be ensured that the excavated soil does not mix with the ballast available. The depth of 1m trench shall b e f r o m t h e bottom o f sleepers for track crossings. Laying of cables and DWC pipes is not included in this schedule. (Supply of DWC/RCC pipes with couplers/collars is not included in this schedule). | Metre 132.00 | — | 385.45 | 50,879.4 |
| 17 | Provision of GI pipes (50/100mm dia) for cable laying with offset at both ends and with couplings over RCC bridges, drainage, culverts, and girder bridges. For RCC bridges, drainage, and culverts, the pipes shall be mounted on concrete masonry supports of size 300mm x 300mm x 300mm at an interval of 2 meters. For girder bridges, the pipes shall be fixed on suitable MS clamps at an interval of 2 meters. The ends of the pipes shall be closed with brick masonry abutments to ensure that no cable is exposed. The work shall be carried out as per the instructions of the Railway representative at the site.(Supply of GI pipes with couplings and laying of cables is not included in this schedule).Stone jelly (20/25mm size), bricks, sand, cement, MS angles, flats, bolts, nuts for manufacturing and fixing clamps, bricks, M sand, cement, and other miscellaneous materials for the work shall be supplied by the contractor. | Metre 186.00 | — | 208.54 | 38,788.44 |
| 18 | Provision of GI pipes (50/100mm dia) for cable laying in hard rocky area with off sets at both ends duly supported b y concrete blocks of size 300mm x 300 mm x 300 mm at an interval of 2m. The ends of the pipes shall be closed with brick masonry abutments work so that no cable is exposed, The work shall be carried out as per the instructions of Railway representative at site.(Supply of GI pipes with couplings and laying of cables is not included in this schedule).[Stone jelly of size 20/25mm, bricks, sand, cement, a n d a l l other miscellaneous materials required for the work shall be supplied by the Contractor]. | Metre 42.00 | — | 182.87 | 7,680.54 |
| 19 | Laying of signaling/power/ telecommunication cables a s p e r cable plan in cable trenches, masonry ducts, RCC Pipes, DWC pipes, GI Pipes etc.(Supply o f cables i s not included in this schedule). | Metre 10500.00 | — | 18.18 | 1,90,890 |
| 20 | Placing of one row of country bricks of size approximately 2 2 0 m m x 1 0 0 m m x 60mm breadth wise horizontally above the cables in 0.3m width trench.[Country bricks of size 220mm x 100mm x60 mm (approximately) shall be supplied by the Contractor]. | Metre 2900.00 | — | 62.99 | 1,82,671 |
| 21 | "Refilling of cable trench 1m depth by 0.3m width throughout, with earth after laying of c a b l e s , a n d consolidating t h e t r e n c h by ramming and levelling." | Metre 2900.00 | — | 15.4 | 44,660 |
| 22 | "Digging of pit to a depth of 800mm of size 300mmX300mm, c a s t i n g o f concrete foundation o f s i z e 300mmX300mmX300mm and Placing of RCC cable markers on top of t h e foundation a n d refilling t h e p i t and consolidating i t b y r a m m i n g . T h e cable markers shall be provided at an interval of 20 Mtrs. within station limits and 50 Mtrs. outside station l i m i t s throughout t h e cable route, diversions a n d a l s o a t every track/road crossing." | Numbers 75.00 | — | 123.35 | 9,251.25 |
| 23 | " R o a d c r o s s i n g / Tr a c k C r o s s i n g through Horizontal Drilling at approximately depth of 1.5 to 2 m below t h e formation level of the earth including insertion of HDPE pipe/DWC pipe along with couplers, drawl of cable (or) direct drawl o f cables e t c . (Note: T h e pilot used for HDD should be of sufficient size to s u i t insertion o f H D P E / D W C p i p e o f size 120mm (outer dia.) or direct drawl of three cables (Signalling/Power/Quad/OFC) or three nos.of 4 0 m m d i a H D P E p i p e o r a n y other combination as directed by the site engineer) ( Supply o f HDPE pipe i s not covered in this schedule)" | Metre 36.00 | — | 1,351.45 | 48,652.2 |
| 24 | B l o w i n g / D r a w i n g o f O F C cable/Power cable/Signalling c a b l e i n s i d e permanently solid lubricated HDPE Pipe already laid. This work includes necessary duct integrity test for solid lubricated H D P E pipe. ( This includes Transportation o f materials from nominated stores to site) | Metre 1500.00 | — | 23.43 | 35,145 |
| 25 | Supply of Colour light Signal pole 140mm dia, 4.6m/ 3.6m tall with necessary inspection as p e r s p e c i fi c a t i o n / drawing/ description enclosed in this document. a)Supply of colour l i g h t S i g n a l p o l e 4 . 6 m tall and 140 mm dia(Galvanised) | Numbers 4.00 | — | 5,841 | 23,364 |
| 26 | Supply of Colour light Signal pole 140mm dia, 4.6m/ 3.6m tall with necessary inspection as p e r s p e c i fi c a t i o n / drawing/ description enclosed in this document. b)Supply of colour light Signal pole 3 .6 m tall and 140 mm dia (Galvanised) | Numbers 4.00 | — | 4,737.7 | 18,950.8 |
| 27 | Supply of ladder with platform and shoes to suit CLS pole 4.6m/ 3.6m tall, with necessary inspection a s p e r specification/ drawing/ description e n c l o s e d i n this document. a)Supply o f ladder w ith platform (4.6m) for CLS(Galvanised) | Numbers 4.00 | — | 5,698 | 22,792 |
| 28 | Supply of Colour Light Signal Multi Unit type- complete for 4/ 3/ 2 aspect with mounting socke t, w i t h necessary inspection a s per specification/ drawing/ description enclosed in this document. a)Supply of colour light Signal unit (4 aspect) | Numbers 4.00 | — | 19,470 | 77,880 |
| 29 | Supply o f cable termination b o x ( F R P type) with necessary inspection as per specification/ d r a w i n g / d e s c r i p t i o n enclosed in this document. | Numbers 4.00 | — | 7,788 | 31,152 |
| 30 | Manufacture and supply o f M.S. relay frames of suitable size to hold up to 4/ 8/ 12/ 20 relays /plug i n type a s required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit and Point control circuits, fixing of plug b o a r d s , r e l a y s , r e s is t o r s and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Ty p e F 5 , w i r i n g a n d termination as per approved circuit diagram a n d painting the particulars.[Wire P V C copper, 3/0.75mm and 1 6 / 0 . 2 m m c o p p e r , P h y n o l i c synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1 9 9 5 - Ty p e F 5 , f o r fi x i n g resistors and condensers, MS flats 25mm x 6mm brass bolts a n d n u t s , p a i n t s , s o l d e r i n g materials, r e s i s t o r s , c o n d e n s e r s a n d a l l other miscellaneous materials required for the work shall be supplied by the contractor]. a)Wiring of Signal/ point/ LC control circuit (up to 4 relays/Plug in type) | Set 10.00 | — | 4,945.51 | 49,455.1 |
| 31 | Carrying out alterations t o the existing relays in the relay racks/apparatus cases as per the approved circuit diagram using wire PVC 16/0.2mm copper. The work includes painting alterations and releasing the unwanted wires c a r e f u lly w i t h o u t disturbing the existing wiring.[Wire PVC 16/0.2mm copper, soldering materials, b u n c h i n g t h r e a d s , condensers, resistances a n d teakwood p l a n k f o r fixing the m a n d a l l other miscellaneous materials required for the work shall be supplied by the Contractor]. | Per 50.00 Relay | — | 695.67 | 34,783.5 |
| 32 | Supply of Handheld True RMS Multi Meter, as per Technical specification | Numbers 2.00 | — | 23,192.34 | 46,384.68 |
| 33 | Supply of Handheld True RMS clamp Meter, as per Technical specification | Numbers 2.00 | — | 33,510.29 | 67,020.58 |
| 34 | S u p p l y o f Fu s i o n S p l i c i n g M a c h i n e with accessories as per Technical specification | Numbers 1.00 | — | 2,95,000 | 2,95,000 |
| 35 | S u p p l y o f Ro d o m e t e r a s p e r Technical specification | Numbers 2.00 | — | 4,252.24 | 8,504.48 |
| 36 | Supply o f Double walled corrugated p i p e - 1 0 3 .5 m m i n n e r d i a & 1 2 0 m m o u t e r dia conforming to specification No. IS 14930(Part 2): 2001 with one coupler for every 6m of pipe as per Technical specification | Metre 72.00 | — | 365.19 | 26,293.68 |
| 37 | Supply o f G I pipes - 100mm dia-4.5mm thick as per Technical specification | Metre 228.00 | — | 1,119.16 | 2,55,168.48 |
| 38 | S u p p l y o f High-Density Polyethylene Pipes (HDPE) of 110 mm Outer Dia, 10 mm Wall Thickness, along with one coupler for every 6 Meters as per specification No. IS 4984: 2016 w i t h l a t e s t a m e n d m e n t s a n d Material Grade:PE 80 | Metre 282.00 | — | 853.55 | 2,40,701.1 |
| 39 | Supply and laying of PVC Warning Tape colour Orange, width o f 250mm (10") by printing w i t h b l a c k l e t t e r s 'Indian RailwaySignal/Telecom/OFC Cable' on both sides | Metre 1000.00 | — | 46.15 | 46,150 |
| 40 | Supply of Electronic Cable Route Marker 3M m a k e o r similar, M o d e l : R F I D ( 1 4 2 1 ) and installation, c a b l e detection o f capacity to detect the cable upto 5 feet depth. | Numbers 20.00 | — | 2,441.72 | 48,834.4 |
| 41 | Supply of HDPE Pipe 40mm (outer dia)/33 mm (inner dia) with couplers | Metre 1500.00 | — | 60.93 | 91,395 |
| 42 | S u p p l y a n d I n s t a l l a t i o n o f Wall/Rack mountable 1 2 Fi b r e management system ( F M S ) conforming t o RDSO/SPN/TC- 37/2000(rev-3 a m d t - 1 o r l a t e s t sim ila r to COMMSCOPE m a k e o r bette r, suitable for splicing and front patching 12F cable with all accessories and terminating the optical fibre cable with splicing and front patching in FMS in the Location Box. This includes Supply and Provision of 4 nos of Patch cords of required l e n g t h ( A l l o t h e r m a t e r ia ls r e q u i r e d for splicing are to be supplied by contractor) | Numbers 5.00 | — | 10,502 | 52,510 |
| 43 | S u p p l y a n d Installation o f s u r f a c e Wall mountable type 1 9 i n c h 1 2 U network Rack with front glass door with lock and rack fixing multipoint A C P o w e r t r i p & all accessories (Power extension board with one set of MCB, exhaust fan, cable manager) | Numbers 4.00 | — | 6,761.51 | 27,046.04 |
| 44 | Supply of track lead junction box - FRP type with 4 terminals and stumps with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. | Numbers 10.00 | — | 1,622.5 | 16,225 |
| 45 | Supply of PBT terminals 25mm/ 60mm centre a n d P B T F u s e b l o c k s w i t h necessary inspection a s p e r specification/ drawing/ description enclosed in this document. a)Supply of PBT terminals 25mm centre. | Numbers 1290.00 | — | 61.44 | 79,257.6 |
| 46 | Supply of PBT terminals 25mm/ 60mm centre a n d P B T F u s e b l o c k s w i t h necessary inspection a s p e r specification/ drawing/ description enclosed in this document. b)Supply of PBT terminals 60mm centre. | Numbers 160.00 | — | 93.02 | 14,883.2 |
| 47 | Supply of PBT terminals 25mm/ 60mm centre a n d P B T F u s e b l o c k s w i t h necessary inspection a s p e r specification/ drawing/ description enclosed in this document. c)Supply of PBT fuse block without ND fuse | Numbers 130.00 | — | 103.84 | 13,499.2 |
| 48 | Excavation o f pit,casting concrete foundation as per Drg.No.SG/CN/02/9 using metallic templates, for erection o f colour light signals up to 4 aspects.[Foundation bolts, cement, M sand, stone jelly of size 20/25mm dia and all other miscellaneous materials required for the work shall be supplied by the Contractor]. | Numbers 4.00 | — | 9,213.28 | 36,853.12 |
| 49 | " E r e c t i o n o f s u r f a c e b a s e , s i g n a l pole, mounting of colour light signal up to 4 aspects complete on Signal pole/ Off-set bracket, (for LED/ filament bulbs) with lenses, triple pole l a m p holder, filament switching u n i t s , CLS transformer, current regulators (whichever is applicable), fixing of ladder w i t h platform complete and concreting of ladder shoe, fixing o f number plates, marker board, lens guard, fi x i n g of speed l i m i t b o a r d wherever necessary, termination of tail cables, wiring of signal unit with P V C w ire 3/0.75mm copper, provision of EWS locks, and painting of one coat of red oxide and two coats of aluminium/ enamel paints. When the aspect is fixed on Offset bracket using 'U' bolts and nuts, a through bolt shall b e provided by drilling a hole i n t h e signal pole t o prevent the offset bracket from sliding down.(Supply of surface base, Offset bracket, CLS pole, C L S aspects complete, ladder with shoes and platform, Speed limit board, LED aspects, current regulators, l a m p holders, lamps, filament switching u n i t a n d CLS transformer is not covered in this schedule).['U' bolts and nuts, through bolts and nuts, cement, stone jelly 20/25mm d i a , M sand, Signal Collar Rings, w i r e P V C 3/0.75mm copper, lens-guard, all fixing bolts and nuts, lead w o o l , paints PVC/Nylon sleeves, enameled number plates. enameled marker boards, EWS locks, a n d all other miscellaneous materials for the work shall be supplied by the Contractor]." | Numbers 4.00 | — | 8,287.08 | 33,148.32 |
| 50 | Hot dip Galvanization of signal post and ladder (4.6m tall, 140 mm dia /3.60 m tall,140 mm d i a ) , c l a m p s , p o i n t r o d d i n g s and other materials related t o Signalling. Minimum DF thickness shall be 80 microns. Transportation o f materials from site/stores to galvanization workshop and back to site/stores not included in this schedule.Transportation charges will be a s per "relevant S O R s c h e d u l e s . Test certificate showing t h e D F T , t y p e of galvanization, materials used etc., from galvanizing firm for each batch to be submitted.(Unit i s calculated b a s e d o n the weight of the Signal poles, ladders, clamps, rodding's etc.,)" | Kg 100.00 | — | 25.31 | 2,531 |
| 51 | Excavation of pit, casting concrete foundation and erection of apparatus case full size as per Drg. No.SG/CN/02/6 and fixing of 2 Nos. of 'E' type locks, one for the front door and another f o r t h e bac k door, fixing o f o n e hard wood s h e l f p l a n k 37mm thick and painting the apparatus case inside and outside with one coat of red-oxide and two coats of aluminium paints.(Supply of apparatus case is not included in this schedule).[Foundation bolts & nuts, ' E ' type locks, cement, M sand, stone jelly o f size 20/25 mm, hardwood plank of 37mm thick, paints, varnish, fixing bolts & n u t s a n d a l l other miscellaneous materials required for thework shall be supplied by the Contractor.] | Numbers 8.00 | — | 11,333.1 | 90,664.8 |
| 52 | " E x c a v a t i o n o f pit, casting concrete foundation and erection of apparatus case half size as per Drg, No.SG/CN/02/7, fixing one 'E' t y p e l o c k f o r t h e f r o n t d o o r and latching arrangement for the back door, and fixing of o n e hardwood shelf plank 37mm thick and painting the apparatus case inside and outside with one coat of red-oxide and two coats of aluminium paints.(Supply of apparatus case is not included in this schedule).[Foundation bolts and nuts, cement, 'E' type locks, M sand, stone jelly of size 20/25mm,37mm hard wood planks, latching ""arrangements, paints, varnish, fixing bolts & nuts and all other miscellaneous materials required f o r t h e w o r k s h a l l be supplied by the Contractor]""" | Numbers 8.00 | — | 8,787.04 | 70,296.32 |
| 53 | Termination o f n e w main/tail cables o n the existing terminals/ fuse blocks in apparatus c a s e s / b a t t e r y b o x e s / C T b o x e s / cable termination r a c k s a s p e r approved circuit diagram. T h e terminal particulars a r e to be r e p a i n t e d / c o r r e c t e d o n t h e d o o r s of a p p a r a t u s c a s e s / b a t t e r y b o x e s / cable termination boxes and FTOT index board as instructed by Railway representative at site. T h i s w o r k i n c l u d e s c l o s i n g t h e opening c r e a t e d f o r e n t r y o f n e w c a b l e s i n the apparatus cases with masonry brick work and sealing t h e bottom o f t h e apparatus cases/ cable termination racks with cable compound. [Paints, wire PVC 3/0.75mm and 16/0.2mm copper, sealing compound, bricks, cement, M sand and all other required miscellaneous materials shall be supplied by the contractor]. (Per Unit = Per Terminal block) | Per Unit 230.00 | — | 73.59 | 16,925.7 |
| 54 | Termination of main, tail, Signaling and power cables a n d internal wiring on terminal/ fuse b l o c k s i n n e w apparatus cases, cable termination b o x e s a n d i n gate Lodges excluding c a b l e termination r a c k at relay room. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing o f Phynolic synthetic industrial fibre base fine weave cotton fibre board 6mm thick for terminal board to suit each apparatus case, varnishing all teakwood items, fixing of terminals/ fuse blocks o n the terminal board, drilling of necessary h o l e s , termination of cables, wiring, identification o f cables using aluminium tags with letters punched neatly, a s p e r approved circuit diagram a n d cable p l a n , p a i n t i n g o f particulars o n sleeves andalso o n t h e inner s i d e o f t h e d o o r s of apparatus cases. After terminations are "over, t h e s i d e o p e n i n g s o f a p p a r a t u s case foundation shall b e closed w i t h brick work, cement plastered, the inter-space filled with M s a n d u p t o b a s e l e v e l a n d t h e bottom s u r f a c e s h a l l b e s e a l e d w i t h sealing compound.(Supply of PBT terminals and Fuse blocks is not covere d i n t h i s schedule)." a)Termination o n 2 5 /6 0 m m P B T terminals (new location)(Phynolic sheet)(Per Unit = Per Terminal block) | Per Unit 850.00 | — | 172.14 | 1,46,319 |
| 55 | Termination of main, tail, Signaling and power cables a n d internal wiring on terminal/ fuse b l o c k s i n n e w apparatus cases, cable termination b o x e s a n d i n gate Lodges excluding c a b l e termination r a c k at relay room. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing o f Phynolic synthetic industrial fibre base fine weave cotton fibre board 6mm thick for terminal board to suit each apparatus case, varnishing all teakwood items, fixing of terminals/ fuse blocks o n the terminal board, drilling of necessary h o l e s , termination of cables, wiring, identification o f cables using aluminium tags with letters punched neatly, a s p e r approved circuit diagram a n d cable p l a n , p a i n t i n g o f particulars o n sleeves andalso o n t h e inner s i d e o f t h e d o o r s of apparatus cases. After terminations are "over, t h e s i d e o p e n i n g s o f a p p a r a t u s case foundation shall b e closed w i t h brick work, cement plastered, the inter-space filled with M s a n d u p t o b a s e l e v e l a n d t h e bottom s u r f a c e s h a l l b e s e a l e d w i t h sealing compound.(Supply of PBT terminals and Fuse blocks is not covere d i n t h i s schedule)." b)Termination o n P B T f u s e b l o c k (new location) (Phynolic sheet)(Per Unit = Per Fuse block) | Per Unit 35.00 | — | 209.93 | 7,347.55 |
| 56 | Termination of main, tail, Signaling and power cables and internal wiring by fixing additional terminals/ fuse blocks on the existing terminal boards of apparatus cases, cable termination boxes etc. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, varnishing all teakwood items, fixing of terminals/ fuse blocks, o n t h e existing terminal boards, drilling o f necessary holes, termination of cables, wiring, identification of c a b l e s using aluminium tags with letters punched neatly, as p e r a p p r o v e d circuit diagram and cable plan, painting of particulars o n sleeves and also o n the inner side o f the doors of apparatus cases. After terminations are over, the side openings of apparatus case foundation shall b e closed w i t h brick work, cement plastered, the inter-space filled with M s a n d u p t o b a s e l e v e l a n d t h e bottom s u r f a c e s h a l l b e s e a l e d w i t h sealing compound. a)Termination o f c a b l e s on 25/60mm PBT terminals (existing location) (Per Unit = Per Terminal block) | Per Unit 600.00 | — | 151.09 | 90,654 |
| 57 | Termination of main, tail, Signaling and power cables and internal wiring by fixing additional terminals/ fuse blocks on the existing terminal boards of apparatus cases, cable termination boxes etc. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, varnishing all teakwood items, fixing of terminals/ fuse blocks, o n t h e existing terminal boards, drilling o f necessary holes, termination of cables, wiring, identification of c a b l e s using aluminium tags with letters punched neatly, as p e r a p p r o v e d circuit diagram and cable plan, painting of particulars o n sleeves and also o n the inner side o f the doors of apparatus cases. After terminations are over, the side openings of apparatus case foundation shall b e closed w i t h brick work, cement plastered, the inter-space filled with M s a n d u p t o b a s e l e v e l a n d t h e bottom s u r f a c e s h a l l b e s e a l e d w i t h sealing compound. b)Termination o f cables o n PBT fuse block (existing location)(Per Unit = Per Fuse block) | Per Unit 50.00 | — | 188.86 | 9,443 |
| 58 | Provision of HDPE Pipe of dia 40/33 mm | Metre 1500.00 | — | 26.11 | 39,165 |
| 59 | "Breaking of concrete and releasing of STOP board/Warning board/ LEGEND boards along w i t h r a i l s , accounting a n d stacking them neatly a t a place a s instructed b y Railway representative at site. Also the resultant pits s h a l l b e re-surfaced a n d consolidating by ramming and levelling" | Numbers 4.00 | — | 1,580.36 | 6,321.44 |
| 60 | Releasing o f existing apparatus cases (Full/ H a l f / Q uarte r s i z e ) w i t h o u t d a m a g e after releasing the shelf planks, Terminal blocks, Fuse Blocks, Terminal Boards, Relays o f all t y p e s E K T s , S e c o n d a r y Cells, power equipments, 'E' type locks, etc., and breaking the concrete foundation. After releasing, the resultant pits are to be closed and consolidated by ramming and levelling. The released materials s h a l l b e accounted and stacked a t a place a s instructed by Railway representative at site. | Numbers 4.00 | — | 3,006.71 | 12,026.84 |
| 61 | Dismantling and releasing of existing Colour light Signals complete (upto 4 aspects) with or without Route Indicators, calling on signals, shunt signals etc., carefully without any damage to the gadgets, accounting and stacking them neatly at a place as instructed by Railway representative at site. The work i n c l u d e s b r e a k i n g t h e concrete foundation,closing t h e r e s u l t a n t p i t and resurfacing it by ramming and levelling. | Numbers 8.00 | — | 3,083.03 | 24,664.24 |
| 62 | Dismantling and releasing of ground lever frame along with all connected gadgets like lever locks, 'E' type locks, HP locks, etc., accounting and stacking them neatly at a place as instructed by Railway representative at site. The work also involves breaking and removal of concrete foundation and the resultant pit shall be filled and consolidated by ramming and levelling. | Set 2.00 | — | 5,550 | 11,100 |
| 63 | Releasing of all the S & T gadgets at LC gates like SM slide instruments, illuminated diagram b o a r d , b l o c k c o u n t e r , termination box, telephones, emergency k e y b o x , etc and concerned wiring, accounting and stacking them neatly at a place as instructed by Railway representative at site. After releasing any holes on the walls/ floor are to be filled with cement mortar and plastered. | Set 2.00 | — | 9,557.1 | 19,114.2 |
| 64 | Protection adjustments and re-instating of S&T gears by deputation of Helpers/Unskilled Labour for executing additional S&T portion of t h e w o r k s . The work can involve fixing, releasing, dismantling, replacement,excavation, clearing of vegetation, loading and unloadingof material and assisting skilled persons etc as per instruction of Railway representative. | Man- 82.00 Days | — | 847.59 | 69,502.38 |
| 65 | Protection, adjustment and reinstating of S&T g e a r s b y d e p u t a t i o n of Fitter/Wireman/Painter/Welder/ Mason/Cable Jointer (Skilled Labour or Technician ) etc., for executing additional S&T portion of works. The w o r k c a n i n v o l v e fixing, releasing, dismantling, replacement, painting or alteration o f vario us signallilng assets or parts, termination of cables, minor patch work on damages at location box, Plastering, Concreting b r i c k w o r k , w i r i n g alterations, cable jointing etc as per instruction of Railway representatives at size. | Man- 55.00 Days | — | 1,073.45 | 59,039.75 |
| 66 | Transportation of Signalling materials by road a s p e r t h e i n s t r u c t i o n s o f Railway representative at site. The work also includes l o a d i n g a n d u n lo a d in g o f the materials a)Transportation o f Signalling materials upto 100kms | MT-Km 2500.00 | — | 22.75 | 56,875 |
| 67 | Engaging mechanical excavators like JCB or other machineries for regarding and levelling t h e formation, dismantling a n y infringing structures, clearing and removing debris etc., with all leads and lifts etc., complete and as per the instruction o f Railway representative at site. | Hour 15.00 | — | 1,202.5 | 18,037.5 |
| Schedule total | ₹57,15,432.38 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TenderDocumentCGLAJJsection.docx.pdf
ATTACHMENT
2026_03_13AdvanceCorrectionSlipNo_111.pdf GCC Corection slip no11
ATTACHMENT
GCC April 2022
ATTACHMENT
GCCCorrectionslip1to10.pdf
ATTACHMENT
SOR2011BOOKLET.pdf
ATTACHMENT
VolumeIIBOOKLET.pdf
ATTACHMENT
JPOforundertakingtheDiggingwork1.pdf
ATTACHMENT
GCC_April-2022_2022_CE-I_CT_GCC-2022_POLICY_27.04.22.pdf
ATTACHMENT
2026_03_13AdvanceCorrectionSlipNo_111.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .