CONSTRUCTION OF 01 NEW LAB AT PM SHRI KENDRIYA VIDYALAY, AIR FORCE STATION DEOLALI

Amount

Excavation in trenches n . exc 1.5 m wide and n. exc 1.5 m in depth; for foundation etc. or for shaft, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n exc 1.5 m in depth and getting out any type of soil deep and getting out in hard/dense soil.

Surface excavation n. exc 30cm deep and getting out in soft soil.

Returning filling including spreading, leveling, watering and well ramming in layers n exc. 25 cm complete all as specified and as directed.

Removing excavated material exc 250 Mtr but not exc 500mtr and depositing, where directed at a level n.exc 1.5 Mtr above the starting point complete all as specified and as directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

M&L for PCC 1:4:8 type D-2 using 40mm stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L brick work with fly ash bricks (FASB) conferming to IS 12894, of strength M-10 straight or curved on plan exc 6m mean radious built cement mortar 1:4 complete (on parapet wall) all as specified and as directed.

Brick work with sub class'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:6) as in Manhole/dwarf wall/septic tank all as specified and directed

M&L re-inforced Cement Concrete, type M-25, (using 20mm graded granite stone aggregate) as in foundations including rafts, footings, plinth beams and mass concrete.

M&L re-inforced Cement Concrete, type M-25, (using 20mm graded granite stone aggregate) as in Columns, piers, posts and struts.

M&L re-inforced Cement Concrete, type M-25, (using 20mm graded granite stone aggregate) as in Beams, cantilevers, lintels over 1.5M span.

M&L re-inforced Cement Concrete, type M-25, (using 20mm graded granite stone aggregate) as in slabs suspended, on walls, beams and columns, in floors, roofs, landings and in shelves and the like.

M&L re-inforced Cement Concrete, type M-25, (using 20mm graded granite stone aggregate) as in chajjas

Use & waste of form work to sides of concrete foundations rafts etc, fair finished, flat all as specified.

Use & waste of form work to sides of pillars, posts, struts, columns and stanchions, fair finished, square, rectangular or polygonal.

Use & waste of form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc. Fair finished, flat.

Use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc 200mm thick, fair finished , flat.

Formwork to chullah hods, chajjas, troughs and similar items including edges

Use & waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls floor and roofs not exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work, fair finished, flat.

M&L reinforcement 10mm and over using TMT bars cut to length bent to shape as required including cranking bending spirally for hooking ends and binding with and including mild steel wire (annealed not less than 0.9mm dia or securig with clips etc complete.

M&L reinforcement 6mm to 8mm TMT bars cut to length bent to shape as required including cranking bending spirally for hooking ends and binding with and including mild steel wire (annealed not less than 0.9mm dia or securig with clips etc complete.

M&L reinforcement 5mm to 10mm TMT bars in stirrups cut to length bent to shape as required including cranking bending spirally for hooking ends and binding with and including mild steel wire (annealed not less than 0.9mm dia or securig with clips etc complete.

M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

M&L Anti Termite treatment of pre construction the top surface of filled earth at the rate of 5 litres of emulsion per sqm of surface

M&L Anti Termite treatment of pre construction the soil under plinth protection at the rate of 5 litres of emulsion per sqm of surface

M&L Anti Termite treatment of pre construction the soil along with external perimeter of building at rate of 2.25 litre of emulsion per meter of the perimeter wall.

M&L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for 75mm thick cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sub base of floor complete all as specified and as directed.

S & F Vitrified Ceramic tiles 600 x 600x 10mm thick (square/ rectangular)polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc over 15mm thick Screed bed with Cement mortar 1:6 and set and jointed in neat cement slurry and pointed in white or coloured cement to match including jambs

M&L for glazed coloured ceramic tiles 300 x 600 x 10 mm thick for work on vertical surface such as skirting, dado, set & jointed in cement slurry and pointed in white or coloured cement to match the existing wall surfaces, over and incl 10mm thick rendering in cement mortar 1:4 etc complete.

M&L renderig 15mm thick in cement mortar 1:6 over fair faces of of brick or concrete surface of wall rendering is to be finished even and smooth without using extra cement.

M&L renderig 15mm thick in cement mortar 1:4 over other than fair faces of brick/stone masonry surface of wall rendering is to be finished even and smooth without using extra cement.

M&L renderig 5mm thick in cement mortar 1:3 on ceiling surface and finished even and smooth with out using extra cment

M & L for preparation of new plastered surface and applying two coat of oil bound distemper on walls over 1mm thick wall care putty complete all as specified and as directed.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including prepration of new wall surfaces.

M & L for preparation of new plastered surface and applying three coat of white wash on ceiling complete all as specified and as directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone including cutting and polishing types over 15 mm thick in CM(1:6) etc complete.

S&F Sheet glass 4.8 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

S&F aluminium anodised barrel tower bolts of extruded section and fixed fixed 200 mm long etc complete.

S&F aluminum handles cast type anodized 150 mm size etc complete.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy.

M&L two coat synthetic enamel paint over one coat of red oxide primer on new steel surface of any description not otherwise described over 10 cm width or girth etc complete.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in plinth protection /path finished even and smooth without using extra cement complete all as specified and directed.

M&L for cement concrete type B-1 ,1:2:4 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L for plain cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

M&L 10 mm thick rendering in cement mortar 1:4 on concrete surfaces when concrete is stil green finished even and fair including mixing of water proofing compound as per manufacturer instruction etc complete all as specified and as directed. Note :- Water proofing compound shall be measured separately as supply only

Supply only integral water proofing compound complete all as specified and as directed.

M&L One coat of bituminous based primer conforming to IS-3384-1965 @ 0.3 Kg/Sqm to be applied on prepared surface, till the surface is properly impregnated.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application with solar reflective bituminous aluminium paint @ 0.10 kg/sqm complete all as specified.

Supplying and laying of 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings and fixed to wall, ceiling or laid in floor. Note :- Rate inclusive of chase cutting in stone/brick masonry of concealed tubing.

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings and fixed to wall, ceiling or laid in floor. Note :- Rate inclusive of chase cutting in stone/brick masonry of concealed tubing.

S & F 1000 litre capacity of rotational moulded polyethylene water storage tank multilayered construction, ISI marked of make specified (cylindrical vertical with closed top) hoisted and fixed in position including S & F 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings complete all as specified in SSR Part-I complete all as specified and as directed.

S&F 20mm CPVC Gate valves (brass insert) as per requirement of the site

S&F 20 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. .(Minimum weight 15mm-142gms/ 20mm-210 gms./25mm-455gms/ 40mm etc complete.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls.

S&F PVC (SWR) bends of radius 110.

S&F 75mm bore CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) .

S&F 100x150mm, P/S type Salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P'

S & F Vitreous China Ware Wash hand basin white, oval shape, glossy finish, under counter size 580 x 410 mm size (Oval shape) fixed to granite slab jointed in cement slurry including waste pipe complete all as specified and directed. Make : Jaquar ( Cat Part : SLS-WHT-6601) or equivalent.

S&F PVC connection 15mm dia with Brass nuts of length 450mm etc complete.

S&F 15 mm bore angle stop cock long thread fancy type chromium plated cast copper alloy, screwed down high pressure with crutch or butter fly handle screwed both and for iron pipe or for union and fixed etc complete.

S&F 15 mm bore bib taps long body chromium plated fancy type, cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe or for unions and fixed 15 mm bore etc complete. Make : Jaquar ( CON -107 KN) or equivalent

S & F 15mm bore swan neck pillar taps, Cast Copper alloy, with capstan heads, chromium plated, fency type screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe. Make : Jaquar ( CON -123 BKN) or equivalent.

S&F brass chromium plated tubeler towel rail D type 600mm long fixed with and dincluding cromium plated brass screws and wooden/plastic cleats complete as specified.

S&F Soap dish any type , fixed to plugs with chromium plated brass screwes.

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

M&L Anodised powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S&F Sliding Powder Anodised aluminium window and ventilator shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as completed

S & F 40 mm thick Flush shutters, solid core construction, with particle board core and if both faces are covered with decorative face veneer with lipping/frame to match

M&L 2nd class HW plain solid straight chowkhats and frames worught framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete

M&L 2 coat of synthetic enamel painting to wood and wood based material surfaces exc 10cm width or girth over a one coat of pink primer incl preparation.

M & L for prepariation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Forming contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound.

Point wiring with PVC insulated and unsheathed multistranded FRLSH copper conductor single core 1.5 sqmm (nominal area) cable using approved colour code as per IS drawing in and incl heavy duty PVC concealed conduit wiring. not less than 25 mm which shall be increased as per site requirement with all accessories suitable for modular type fitment including provision for fixing of modular flush boxes of suitable size complete alongwith copper earth wire PVC insulated & unsheathed multistranded (FRLSH) copper conductor cable of size 1.5 mm as continuous earth wire connected to common earth dolly complete all specified and marking good disturbed surfaces of wall, floor or ceiling with plaster and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete and as directed Engr-in-Charge. (a) One light point/Fan point controlled by one switch. Make : Polycab, Havells, KEI, Legrand

(b) One 3 pin socket outlet 5Amps on the same board with other swithches.

Point wiring with PVC insulated and unsheathed multistranded FRLSH copper conductor single core 2.5 sqmm (nominal area) cable using approved colour code as per IS drawing in and incl heavy duty PVC concealed conduit wiring. not less than 25 mm which shall be increased as per site requirement with all accessories suitable for modular type fitment including provision for fixing of modular flush boxes of suitable size complete alongwith copper earth wire PVC insulated & unsheathed multistranded (FRLSH) copper conductor cable of size 2.5 mm as continuous earth wire connected to common earth dolly complete all specified and marking good disturbed surfaces of wall, floor or ceiling with plaster and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete and as directed Engr-in-Charge. Make : Polycab, Havells, KEI, Legrand

M &L for ceiling rose 2to 3 terminal PVC/polycarbonate, isolated body type suitable for AC 230 volts complete all as specified. Make : Anchor, Havells, Legrand

M & L for module cover plate with frame as per site requirements for following module complete all as specified and as directed. (a) 1 module Make : Anchor, Havells, Legrand

(b) 3 module Make : Anchor, Havells, Legrand

(c) 6 module Make : Anchor, Havells, Legrand

M &L for modular metal flush box as per site requirement complete all as specified and as directed. (a) 1/2 module Make : Anchor, Havells, Legrand

(b) 3 module Make : Anchor, Havells, Legrand

(c) 6 module Make : Anchor, Havells, Legrand

M & L for modular switch 1 way 6 Amp 1 module complete all as specified and as directed Make : Anchor, Havells, Legrand

M & L for modular switch 1 way 16/20 Amp 1 module complete all as specified and as directed. Make : Anchor, Havells, Legrand

M & L for modular socket 6A 2/3 pin universal 2 modular, complete all as specified and as directed. Make : Anchor, Havells, Legrand

M & L for modular socket 16A/6A 2/3 pin combined 2 module complete all as specified and as directed. Make : Anchor, Havells, Legrand

M & L for modular fan step regulator 120 well 2 module complete all as specified and as directed. Make : Anchor, Havells, Legrand

Supply and fixing ceiling fans complete with blades, down rods, with remote, clamps accessories complete with nut bolt, 230 V, 1400 mm sweep. Min air delivery 245 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) Make : Orient, Havells, Usha

S & F energy saving efficient 20 watt (4.0 feet) LED integrated batten type luminaries suitable for wall or ceiling mounting with built in LED chip & integral LED driver 20 watt invertor, Aluminum channel housing & polycarbonate diffuser of length 1200 mm (approx), colour temperature 6500 K or as directed, CRI between 80-85 Low THD, PF-0.90(minimum), efficiency not less than 100 lumen/watt or total lumen output not less than 2000 lumen per 20 watt operating range 200-270V, surge protection of 2 KV over voltage protection and other safety tests as per IS 15886 Part -2/Part-3 estimated life span of 50,000 hrs with all accessories, complete with fixing arrangement, fitting shall be internally prewired and conforming to LM 79 & LM 80 standard, making all connection using 1.5 sqmm copper conductor multistandard PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through PVC flexible conduit complete fixed in position & connection complete all as specified and directed by Engr-in-Charge Note (i) LED fitting shall be provided for 3 years warranty. Make : Havells, Bajaj, Phillips

S & F energy saving efficient 10/12 watt (2.0 feet) LED integrated batten type luminaries mirror type suitable for watt or ceiling mounting with built in LED chip & integral LED driver 10/12 watt invertor. Aluminum channel housing & polycarbonates diffuser of length 600 mm (approx) Color temperature 6500 k or as directed efficiency range 200-270V surge protection of 2 KV estimated life span of 50,000 hrs with all accessories, complete with fixing arrangement fitting shall be internally prewired and confirming to LM 79 & 80 standard, making all connection using 1.5 sqmm copper conductor multistandard PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through PVC flexible conduit complete fixed in position & connection complete all as specified and directed by Engr-in-Charge (Note (i) LED fitting shall be provided for 3 years warranty (ii) Location for installation of LED fitting shall be as per approved drawing) Make : Havells, Bajaj, Phillips

Supply and fix distribution board (DB), double (CRCA sheet ) dust and vermin proof SPN 8 way with appropriate Amps rated copper busbar, neutral bar, internal earth bar and cable tiles for cable management reversible door for iP 43 & IP 54, IK 09 impact resistance, single pole and neutral 250 volts ,flush to watt including chases cutting in wall for fixing good distributed wall surfaces to match with existing specification complete all as specified all as directed Note – Rates are inclusive for flush (concealed) mounting of DB SPN) Make : L&T, Havells, Legrand

All as per Item No 96 above but, SPN 4 way with appropriate Amps rated complete all as specified all as directed Note – Rates are inclusive for flush (concealed) mounting of DB SPN) Make : L&T, Havells, Legrand

Supply and fixing 240V, 10 KA ‘C’ curve miniature circuit breaker (MCB) single pols of current carrying capacity 6 to 32 AMP, in the MCB DB complete with connection testing and commissioning all as specified and directed. Make : L&T, Havells, Legrand

Supply and fixing 240V, 10KA ‘C’ curve miniature circuit breaker (MCB) single pole and nutral of current carrying capacity 32 Amps, in the MCB DB complete with connection testing and commissioning all as specified and directed. Make : L&T, Havells, Legrand

M & L sub main wiring using PVC insulated FRLSH cable 4.0 sqmm and unsheathed multistranded FRLSH copper conductor cable using approved colour code as per IS drawing in and intel PVC concealed conduit wiring with all accessories and making good disturbed surfaces of watt, floor or ceiling with plaster and finishing the surfaces with distemper/white washing/color washing tom match with the existing surface complete as per specified and as directed by Engr-in-Charge of the following sizes of cables. Note : 2 runs of 4 sqmm copper cable ^ 1 run of 4.0 sqmm copper cable in and includingPVC concealed conduit wiring shall be measured as one unit.

S&F or exhaust fan 450mm sweep, heavy duty motor with double ball bearing ,metallic body with laid guard to protect the dan to running AC, single phase 230 volts, including connection with 1.5 sqmm multi standard copper conductor flexible wire from ceiling rose, complete with blades/frame and outside louvers with necessary fixing arrangement and making good to disturbed surface complete all as specified and directed. Make : Bajaj, Usha, Havells

M & L for Earthling compete with GI earth electrode plate of Size 600x600x6mm thick, buried directely to ground/earth pit not less than 2.25m deep below normal ground level, connected to GI wire 4 mm dia as earth lead up to test point with suitable GI nut/bolts and brazed properly up to main board including earth pit in cement concrete 1:2:4 reinforced with expanded metal weight not less than 4 kg/sqm and frame of angle iron 25x25x6mm with lugs 02 nos with 5 mm dia MS bar handle made to shape excavation and earth work in any type of soil and including light grade GI watering pipe 20mm bore with funnel and wire mesh and light grade of earth wire protection pipe 15mm bore up to main board complete as shown in electrical plate no 3 of MES schedule Part-I ,connected to earthling testing point and testing on completion complete all as specified and directed by Engr-in-Charge.

Supply and spreading sand under floors or in foundation including watering and consolidation.

M&L for machine pressed concrete interlocking paver block with g-rey cement and pigment any shape , size and colour confirming to IS 15658 of 60mm thickness , M-40 grade.

M&L for PCC 1:2:4 (type B1) using 20mm graded stone aggregate as in coping ,benching for man hole including necessary form work and finishing all exposed surfaces of concrete even and smooth using extra cement all as specified and directed.

Removing excavated material (soils) nexc 250m and depositing where directed at a level not exc 1.50m above the starting point all as specified & directed.

Excavation in trenches not exc. 1.5 mtr wide and not exc 1.5 mtr depth in any type of soil (soft/loose/hard/dense soil) for laying / taiking up/ taking down of water pipes of any size and type including levelling of bottom surface to required level all as specified and directed by Engineer-in-Charge.

Returning filling in trenches including spreading, levelling, watering and well ramming soil in layers not exceeding 25 cm thick all as specified and directed.

Removing excavated material from site to a distance n. exc. 50 mtrs away and depositing where directed at a level n. exc. 1.5 mtr avove the starting point all as specified and directed by Engineer-in-Charge.

Supply and lay 25 mm bore galvanised steel water tubing medium grade including all fittings such as bends, elbows, tees, reducers, sockets, union etc and laid in trenches complete all as specified and drected.Make-Swastic,Jinadal or equivalent. Note : Excavation & earthwork will be measured & paid sperately.

All as per item no.04 above but 50mm bore make-Swastic,Jindal or Equivalent.

Material and labour for Cutting and screwing existing steel tubing or alterations or additions of following size:25mm bore.

All as per item no.06 above but 50mm bore .

Supply & Fix of Bronze gate valve (Hex type) ISI marked screwed both ends of 50 mm diameter Art No 1006 of Make: Zoloto or Equivalent in Leader/L&T, complete all as specified and as directed by Engineer-In-Charge.

Supply & Fix of Bronze gate valve (Hex type) ISI marked screwed both ends of 25 mm diameter Art No 1006 of Make: Zoloto or Equivalent in Leader/L&T, complete all as specified and as directed by Engineer-In-Charge.

Supply and laying intranch fitted on wall Bldg of LT XLPE insulated/PVC heavy duty armoured cablle 1100 volts grade UG mult-stranded aluminium conductor electric cable cross sectional area 35 Sqmm 3.5 Core including necessary connection with provision of lugs & cable gland fixing arrangements all as specified and directed. Make : Polycab, Gloster, Havells

Supply and laying intranch fitted on wall Bldg of LT XLPE insulated/PVC heavy duty armoured cablle 1100 volts grade UG mult-stranded aluminium conductor electric cable cross sectional area 16 Sqmm 2 Core including necessary connection with provision of lugs & cable gland fixing arrangements all as specified and directed. Make : Astral, Rex, Duraline or euilent

M&L for double wall corrugated (DWC) duct (dure guard) as per IS 14930 part II LT UG cable protection including coupler, elbows, T joiints, Bends etc. and test report Make: Dura line/ Gemini/ Rex of size 38mm inner dia and 50mm outer dia al as per direted by Engr in charge.

Excavation in trenches n. exc 1.5 Mtr wide and n. exc 1.5 mtr in depth and getting out in soft soil.

Excavation in trenches n. exc 1.5 Mtr wide and n. exc 1.5 mtr in depth and getting out in hard soil.

Returning Filling in including spreading, leveling, watering & well ramming in layers n. exc 25 Cm.

Removing excavated/Surplus soil n exc 50 Mtr & depositing where directed at a level n. exc 1.5 Mtr above the starting point.

M&L for Cable route indicator fabricated from 40x40x6mm angle iron 450mm long, rivited or welded with 100mm dia CI or MS round disc duly engraved " LT cable" in letters including grouted in ground with PCC 1:4:8 type D-2 compete all as specified and directed by Eng in Charge

Supply, install, testing and commissioning of cubicle type outdoor LT distribution panel fabricated out of 3.15mm thick CRCA sheet with separate locking arrangement, painted with epoxy powder coated over a coat of red oxide primer, factory made, cubicle type, double door hinged type, both side openable, provided with 6mm thick bakelite / fiber sheet for mounting electrical accessories, holes for cable entries, detachable gland plates at top and bottom, earth connection terminals etc. and mounted on 40x40x5 mm size angle iron frame, adequate clearance from ground level for the entry and exit of cables, provision of ventilation on sides, manufacturer details, necessary PCC work for grouting and provn of cable lugs for connection etc. complete and consisting of following:- (a) MCCB 100 Amp 4 pole, 10 KA -01 Nos ( as main incomer) (b) LED indication lamps 3 Phase, (c) Aluminum bus bar 200 Amp (d) Multifuction panel meter square type to measure three/single Voltage phase, load current, frequency, power factor kWh including necessary CT/PT of suitable ratio 01 Nos (d) MCCB 63A 4 pole, 10 KA -02 Nos ( as out going)

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to GI strip 25x4mm through GI pipe light grade 40 mm dia by means of bolts,nuts, check nuts and washers of galvanised iron or steel, proper watering arrangements with medium grade GI pipe 20 mm, funnel etc. PCC chamber,Chamber Cover all as shown in electrical plate no 3of SSr part I 2009 connected to earthing test point all as specified or indicated and testing on completion.

Excavation in trenches, not exceeding 1.5M wide and not exceeding 1.5M depth for foundation etc and getting out in Hard/ dense soil all as specified of 150mm bore.

M&L for PCC 1:3:6 (type C-2) using 40mm graded stone aggregate for bed to drain pipe of dia 150 mm including packing under and hauching against the side of pipes

M&L for RCC pipe class NP-2 laid in jointed complete with collars , bore of pipe 150mm complete all as specified and directed by engr-in-charge .

M&L for PCC 1:3:6 (type C-2) using 40mm graded stone aggregate as in foundations, filing and mass concrete.

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6.

M&L for rendering 15 mm thick in cement mortar 1:4 mixed with water proofing compound on fair surfaces of stone masonry work or concrete surfaces and finished even and smooth with using WPC (Note : WPC shall be measured & paid separately).

Supply only integral water proofing compound.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including form/moulds, mitred/stop end etc complete all as specified & directed.

M&L for precast RCC 1:2:4 (type B1) using 20mm graded stone aggregate as in cover slab for manholes etc set in CM (1:4) and finishing all exposed surfaces of concrete even & fair without using extra cement all as specified.

S&F TMT bars 10mm and over dia cut to length bent to shape required including bending, hooking, binding with and including MS witre not less than 0.9mm dia.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soils.

Removal of excavated material exc 50mtrs and depositing where directed at a level of n.exc 1.5mtrs above the starting point in soil.

M&L for PCC 1:3:6 (type C-2) using 40mm graded stone aggregate as in surface channels and drains.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM1:6.

M&L for rendering 10 mm thick in cement mortar 1:4 on concrete surfaces and finished even and smooth .

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in Hard /dense soil

N.U. MIRZA (BID ID -3344932)

Vinod Enterprises (BID ID -3345197)

shubham Enterprises (BID ID -3342330)

M/s.TIRUPATI BUILDERS (BID ID -3343688)

BHUSHAN BHIMRAO PATIL (BID ID -3345645)