REPAIR PAINTING POLISHING TO WOODEN AND STEEL FURNITURE AT CQA AREA UNDER GE MH AND RH KIRKEE

Amount

Taking down carefully / removing following unserviceable component / member of TABLE DINING 6 / 8 PERSONS and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge Note : (i) Timber shall be of Ist class hard wood Teak (ii) 4 mm thick teak wood beading shall be provided all round all as shown on drg. Drg No : TABLE DINING 6 / 8 PERSONS (FD-273,30(M)/FD/MAP/-II/03)

18/19mm thick Prelaminated MDF Board two side laminated exterior grade type two grade-I ISI marked table top for table dining 8 persons of size 1800 x 900.

18/19mm thick Prelaminated MDF Board two side laminated exterior grade type two grade-I ISI marked table top for table dining 6 persons of size 1500 x 900.

Leg of size 75 x 40 x 742 mm

Long rail of size 25 x 100 x 1800 mm

Long rail of size 25 x 100 x 1500 mm

Short rail of size 25 x 100 x 900 mm

Stiffener 25 mm thick and 90 mm wide

Corner of table dining

PVC/hard rubber shoe

Taking down carefully / removing following unserviceable component / member of CHAIR DINING and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge Note : Timber shall be of Ist class hard wood Teak Drg No : CHAIR DINING (FD-279, FD-228)

Tightening and fixing of loose parts of chair dining with bamboo pins and SS screws complete.

Rail with suitable holes for canning.

Front leg

Rear leg

Stiffner

Back rest

PVC/hard rubber shoe

Corner of chair

Taking down carefully / removing following unserviceable component / member of CHAIR WRITING and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge Note : Timber shall be of Ist class hard wood Teak Drg No. : CHAIR WRITING (FD-250, FD-280)

Tightening and fixing of loose parts of chair dining with bamboo pins and SS screws complete.

Rail with suitable holes for canning.

Front leg

Rear leg

Stiffner

Arm rest

Back rest

PVC/hard rubber shoe

Corner of chair

Taking down carefully / removing following unserviceable component / member of CHAIR EASY and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge Note : Timber shall be of Ist class hard wood Teak Drg No. : CHAIR EASY (FD-229)

Tightening and fixing of loose parts of chair easy with bamboo pins and SS screws complete.

Rail with suitable holes for canning.

Front leg

Rear leg

Arm rest

PVC/hard rubber shoe

Corner of chair

Taking down carefully / removing following unserviceable component / member of CHAIR DINING WITH CUSHION and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge. Drg No : CHAIR DINING WITH CUSHION: (MAP): FD/E6/ MAP/II/04

Cushion 32 density 75mm thick for seat duly covered leathrite rexine (Not less than Rs 250/- per mtr) (shade as approved by GE/Engr-in-Charge) as per existing shape and size as directed by GE.

Front leg

Rear leg

Batten

Side rail

12mm thick BWR plywood for seat.

Taking down carefully / removing following unserviceable component / member of BED PLY TOP and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge Note : Timber shall be of Ist class hard wood Teak Drg No : BED PLY TOP (FD-246)

Tightening and fixing of loose parts of bed hard with ply top with bamboo pins and SS screws complete.

Long rail

4mm Thick one side teak face ply wood ISI Marked BWR of size 780 x 340 mm on both side of head board all as per drg.

4mm Thick one side teak face ply wood ISI Marked BWR of size 780 x180 mm for foot board on both side of Foot board all as per drg.

12 mm thick Plywood BWR grade for bed top size as per drg

Bottom rail

Leg of head board

Leg of foot board

Corner of bed

Taking down carefully / removing following unserviceable component / member of SOFA SET 5 SEATER / 4 SEATER and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge Drg No : SOFA SET 5 SEATER / 4 SEATER (FD-281/ FD-373/ FD-258)

Replacement of existing tapestry and cushions of sofa set by replacing old unserviceable cushion with 40 density U-foam new cushion (size as per drg) including providing long cloth lining for cushion, covered with new tapestry cloth of first quality (as per sample available at BSO yard) and rate not less than ₹ 750/- per RM) of approved shade duly stiched in shape and provided with good quality nylon zip on one side for sofa set 5 seater for Set of 10 cushions.

Front or rear leg

Batten

Long rail (front or rear) of sofa single seater

Long rail (front or rear) of sofa 3 seater

Removing old faded tapestry cloth from cushion of sofa set five seater (two single plus one three seater) and S & F tapestry cloth of best quality not less than ₹750/- per metre as per approved sample for complete sofa set five seater as per requird size / shape complete all as specified shown in drwaing and as directed.

Removing Old unserviceable cushion of sofa set five seater (two single seater + one three seater) and S & F 100mm thick cushion (cool foam) 40 density duly upholestered/covered with new cover.

M & L for preparation of old decorated / new replaced parts/surface of sofa set five seater smoothening by required grade of sand paper and applying one or more coats of french polish to achieve glossy finish including tightening the frame work all as specified shown in drawing and as directed.

Taking down carefully / removing following unserviceable component / member of TABLE DRESSING LADIES and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge. Drg No : TABLE DRESSING LADIES (FD-251/ FD-32)

Box w/o Drawer of 18/19mm thick prelaminated particle board exterior grade with 4mm thick teak wood beading all as per drg.

Sliding glass shutter 5 mm thick of size 550mm x 380mm with aluminum channel of table dressing ladies complete all as per drg & as specified and directed.

Mirror 366mm x 1220 x 5mm thick of table dressing ladies, complete all as specifed and directed.

Back frame made out of 6mm thick commercial ply wood and 45mm x 40mm 1st Class teak wood frame, as per existing, complete as specified and directed.

Chromium plated knob 25mm dia 24mm length of best quality as approved.

Drawer of 12mm thick prelaminated particle board exterior grade approved by GE with 4mm thick teak wood beading all as per drg.

Legs with frame complete all as specified and directed.

Taking down carefully / removing following unserviceable component / member of TABLE DRESSING GENTS and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge. Drg No : TABLE DRESSING GENTS (FD-230/FD-31)

Box (size 900 x 300 x 150 mm) w/o drawer of 18/19mm thick prelaminated particle board exterior grade approved by GE, with 4mm thick teak wood beading all as per drg.

Mirror of size 380mm x 760mm x 5.0mm thick all as shown on drg, and directed by the Engineer-in-Charge.

Back frame made out of 35mm x 25mm 1st Class teak wood & 6mm thick commercial ply grade MR, type BB, all as shown on drg, and directed by the Engineer-in-Charge.

Chromium plated knob 25mm dia all as per drg.

Drawer of table dressing gents as per existing/drawing complete all as specified and directed.

S&Fand Fitting of loose /dismantaled / sagged table dressing gents to the wall with "L" Bracket (Pair) as per drg and all accessories such as screw,clips, plugs, clamps, etc complete all as directed by Engineer-in-Charge.

Taking down carefully / removing following unserviceable component / member of TABLE CENTRE and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge. Drg No : TABLE CENTRE (FD-274)

18/19 mm thick of Prelaminated MDF Board two side laminated exterior grade type-II grade-I with 4mm thick teak wood beading for table center Top all as per drg.

Short rail

Long rail

PVC/hard rubber shoe

Taking down carefully / removing following unserviceable component / member of TEAPOY WOODEN and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge. Drg No : TEAPOY WOODEN (FD-278)

18/19 mm thick of Prelaminated MDF Board Two side laminated exterior grade type-II grade-I for top with 4mm thick teak wood beading all as per drg.

Short rail

Long rail

PVC/hard rubber shoe

Taking down carefully / removing following unserviceable component / member of TABLE BED SIDE and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge. Note : 4 mm thick teak wood beading shall be provided all round all as shown on drg. Drg No : TABLE BED SIDE (FD-276)

18/19 mm Thick prelaminated Particle board exterior grade for table bed side top of same size and shape.

18/19 mm Thick prelaminated Particle board exterior grade for table bed side, sides of same size and shape.

12 mm thick prelaminated Particle board exterior grade for shelf of same size and shape.

6 mm thick BWR ply wood for Back conforming to IS: 303 BWR grade all as specified and shown in drg.

Taking down carefully / removing following unserviceable component / member of TABLE WRITING and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge. Drg No : TABLE WRITING (FD-33/FD-249 /FD-275)

18/19 mm thick of prelaminated MDF Board two side laminated exterior grade type-II grade-I for Table writing Top of size 1145 x 600 with 4mm thick teak wood beading all as per drg.

6mm plywoood including chromium plated knobs etc in bottom of drawer all as shown on drawing.

Stiffner

Drawers of size 600 x 500 made out of 18 mm prelaminated Particle board exterior grade ISI marked all as per drg complete.

Lock of drawers 6 lever 50 mm

PVC/hard rubber shoe

Long rail

Short rail

6mm thick ply wood for rear side

Shutter made of 18/19mm prelaminated Particle board exterior grade with 4mm thick beading hung with SS piano type hinges including one knob complete as per drg.

Taking down carefully / removing following unserviceable component / member of BOOK CASE and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge. Drg No : BOOK CASE (FD-45)

6 mm Thick commercial ply back as per shape and size shown in drawing of including french polishing to match the other parts

Bottom frame and legs made of 1st class teak wood

18/19 mm thick prelaminated Particle board exterior grade for door shutter

M & L for preparing old wooden surfaces / replaced member of furniture items of any description by sand paper, removing the stains and filling holes, cracks by putting bees wax and chalk powder etc, and applying two coats of french polish to glossy finish to the exposed surface shade shall as approved by GE for the following articles:-

Bed ply top DRG NO: FD-246

Book case small DRG NO: FD-237/FD-45(M)

Chair Dining DRG NO: FD-16/FD-279/FD-228

Chair easy DRG NO: FD-229

Chair Writing DRG NO: FD-280/FD-250

Table centre DRG NO: FD-274/FD-235

Table dining 6/8 pers DRG NO: FD-30(M) /FD-239/FD-273

Teapoy DRG NO: FD-278/FD-232

Table 3'x2' without drawer/withdrawer DRG NO: FD-284/FD-283

Stool Dressing DRG NO: FD-252 /FD-282

Table Dressing Gents DRG NO: FD-31(M) / FD-230

Table office clk (w) DRG NO: DB-4120

Table office officer (w) DRG NO: DB-4119

Hat stand DRG NO: FD-233 / FD-206

Table dressing ladies DRG NO: FD-251 / FD-32

Table writing DRG NO: FD-275/FD- 249

Sofa Single Chair DRG NO: FD-258 / FD-281

Sofa set 3 seater DRG NO: FD-258 /FD- 281

REPAIRS TO CHAIR VERANDAH: DRG NO : FD-359 Note for item Nos 19.01 to 19.04 :- (i) Old damaged canning shall be removed before painting. (ii) Colours of cane and paint shall be as approved by GE.

Taking down old existing unserviceable cane from chair verandah and Material and Labour for preparation of existing painted surfaces of steel frame of chair verandah by hand scrapping, cleaning of the surfaces and applying two coats of synthetic enamel paint including preparation of steel surface complete all as directed.

M&L for reweaving the same with new 4mm wide plastic cane oval type best quality, in seat and back, complete all as shown on drawing and as directed by Engr-In-Charge.

Material and Labour for welding before painting as required broken portion of Chair. In repairs exc 2.5 but not exc 5cm length and thickness of metal to be welded not exc 6mm

PVC/hard rubber shoe

Taking down carefully / removing following unserviceable component / member of BED HARD STEEL MAP and supply, fixing and tightening new component / member with bamboo pins and SS Screws (ISI marked) as per existing shape and size complete all as shown on drg and as directed by Engr-in-Charge. DRG NO :BED HARD STEEL MAP FD/MAP/08(R)

Head rest size 25" x 9¼" x 18mm Prelaminated MDF Board two side laminated exterior grade type two grade one ISI marked.

Foot rest size 25" x 12" x 18mm Prelaminated MDF Board two side laminated exterior grade type two grade one ISI marked with 4 side 4mm thick TW beading in Bed Hard Steel all as per drg.

12mm thick BWR Gde ply 78"x33½’ of ISI Marked all as per Drg and as directed by Engineer-in-Charge.

Taking down carefully unserviceable cane from different types of chairs and M&L for recaning the same with new 2mm wide oval type plastic cane and bordering with 3mm wide plastic cane complete all as shown & as directed.

Taking down carefully / removing following unserviceable component / member of TABLE OFFICE OFFICER STEEL and supply, fixing new component / member all as per drg complete. DRG NO : TABLE OFFICE OFFICER STEEL FD-1002/FD-1003/ FD-84(M)

18/19 mm Prelaminated MDF Board two side laminated exterior grade type two grade one ISI marked with teak wood beading all round 4 mm thick all as shown on drg.

Drawer

Hard rubber shoes

Taking down carefully / removing following unserviceable component / member of ALMIRAH LARGE STEEL WITH SHELVES: and supply, fixing new component / member all as per drg complete. Drg No. : ALMIRAH LARGE STEEL WITH SHELVES: DRG NO: FD-67 /FD-1031

CP handle 125 mm with nut and bolts as per drg.

Locks of 6 lever as per drg.

Locking device including MS Rod rest all as per drg.

MS hinges of reqd size as per drg.

Legs made out of 1 mm nominal thick MS sheet as per drg.

Shelve made out of 1mm nominal thick MS sheet as per drawing.

Shutters made out of 1mm nominal thick MS sheet as per drawing.

Adjustment of exsisting shelves by providing new clamps after removing unserviceable clamps all as directed by Engr-in-charge

Taking down carefully / removing following unserviceable component / member of ALMIRAH MEDIUM/SMALL STEEL WITH SHELVES and supply, fixing new component / member all as per drg complete. DRG NO: ALMIRAH MEDIUM/SMALL STEEL WITH SHELVES (FD-243/FD-1032)

CP handle 125 mm with nut and bolts as per drg.

Locks 6 lever as per drg.

Locking device including MS Rod rest all as per drg.

MS hinges of reqd size as per drg.

Leg made out of 1 mm MS sheet as per drg.

Shelf made out of 1mm nominal thick MS sheet as per drawing.

Shutter made out of 1mm nominal thick MS sheet as per drawing.

Adjustment of the existing shelves by providing new clamps after removing unserviceable clamps all as directed.

Taking down carefully / removing following unserviceable component / member of TABLE OFFICE CLERK STEEL and supply, fixing and tightening new component / member as per existing shape and size complete & all as shown on drg and as directed by Engr-in-Charge. Drg No : TABLE OFFICE CLERK STEEL (FD-84 / FD-1004)

18/19 mm Prelaminated MDF Board two side laminated exterior grade type two grade one ISI marked with teak wood beading all round 4 mm thick all as shown on drg.

Drawers

Locks

Hard rubber shoes

M&L for preparing old painted steel surfaces (internal & external) by sand paper, cleaning, including denting patches by filling putty (metal paste) and applying one coat of synthetic enamel paint, shade shall as approved by GE/Engr-in-charge for the following articles/ items:-

Almirah large steel Drg No. FD-67 / FD-1031

Almirah med steel Drg No. FD-1032/FD-243

Table office officer steel Drg No. FD-84/FD-1002/FD-1003

Table office clerk steel Drg No. FD-84/FD-1004

CHAIR CBA STEEL WITH ARMS : DRG NO : FD-75

M&L for removing existing old unserviceable Seat and Back of Chair Steel Tubular with Arm (FD-75) and Welding MS FIat 11" x 2" and 4mm thick for seat (02 Nos) and Welding MS FIat 8" x 2" and 4mm thick for Back (02 Nos) on GI Tube frame work as per direction of Engr-in-charge. (a) Steel GI Tubing parts (frame Work) of chairs duly scrapping for removal of rust, dirt and Two coat of SE paint of Black colour or shades approved by Engr-in-Charge (b) S&F Plywood 12mm thick commercial size 18½" x 18¼" fixed on welded MS Flat (cleats) with the help of suitable Nut & Bolt with washer for a seat and paste 50mm U Foam on plywood for cushioning of Seat coverd with tepestry cloth with the help of suitable stappler pin for upholstery work . (as per sample kept in BSO Yard) (c) S&F Plywood 12mm thick commercial size 18¼" x 16" fixed on welded MS Flat (cleats) with the help of suitable Nut & Bolt with washer for a Back and paste 50mm U Foam on plywood for cushioning of Back coverd with tepestry cloth with the help of suitable stappler pin for upholstery work (as per sample kept in BSO Yard) . Note : Tepastry cloth (Not less than 200/- per mtr) as per sample kept in BSO Yard or shades approved by Engr-in-Charge

S & F in repairs hand rest made of 2nd class hard wood duly polished in black colour as per drg.

S & F in repairs caps as per drg.

S & F in repairs PVC/hard rubber shoes as directed by Engr in Charge.

M&L for welding in reapairs exceeding 2.5 but not exceeding 5cm length and thickness of metal to be welded not exceeding 6mm all as directed.

M/s Green Leaf Electricals

Mahesh Traders