REPAIR TO ROAD AND ROAD FURNITURE WITH OTHER ALLIED WORKS AT KWC AND METCALFE HOUSE AREA UNDER GE I RND DELHI

Amount

M&L for repair to pot holes any depth, not exc, 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths etc cutting around edges to at least 25 mm in depth, making good by applying tack coat @ 5Kg per 10 Sqm, putting in pre-mixed bituminous macadam, well rammed and sealed with binder 9.8 Kg/10 Sqm and blinded with 0.09 Cum of stone chippings, 6.3 mm size and again well rammed (including supply of premixed macadam, binder and chippings), depth of potholes exc 30mm complete all specified and directed.

M&L for preparing of existing black top surface by brooming or brushing with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dust etc and applying evenly a priming/ tack coat with bituminous primer of paving bitumen(VG-10) @ of 5 Kg /10 Sqm with mechanical sprayer and laying of Bituminous premixed Semi Dense Asphaltic Concrete 25 mm thick consolidated thickness with binder content of paving bitumen (VG-30) @ 5.5 % by weight of total mix including supply of filler (OPC cement) as per design mix, spread using Mechanical sensor paver rolled and compacted with 8 to 12 ton power road roller to a required camber and gradient complete all as specified and directed. The content of Bitumen specified in this item is maximum content, in case, the quantity of Bitumen required is less as per approved design mix, the minus price adjustment for less quantity of bitumen shall be made @Rs.50.00/Kg Note " Material shall be broght at site from approved / authorised Hot Mix plant at any distance. Hot mix plant shall be got approved from GE(I).

M&L for preparation including cleaning the surface of all dirts scales and foreign materials of new bituminous surfaces of road dispersal and applying thermo plast reflective type road marking material conforming to BS standard 3362 with 20% glass beads (Inter mixed) minimum 2.5 mm thick with hot application, white or golden yellow by automatic engine drive in desire pattern not exc 10 cm wide over and including applying one coat of sealing primer complete all as specified and directed.

S&F in repair Plastic Speed Bump which are highly resistant to severe impacts and harsh weather condition. Its interlocking sub units make it bind perfectly into a one firm bump. Its fixing with metalic bolts/MS Stud/Anchor fastener and suitable adhesive are used for installation on road. Make : Road star Model No. GP1006 or equivalent approved.

S&F in repairs ABS Plastic body road studs/cat eye highly reflective and can withstand a load of more than 10 Tons, fixed to road surface with MS stud /Anchor bolts coplete all as specied and directed. Make : Road star Model No. 3M 290 series or equivalent approved.

S&F in repair Stainless steel (Grade 304) hollow round or square pipe of minimum 16 gauge thickness fixed as in posts for sign board with frame work structure as design by Engr-in-charge for fixing sign board, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete all as specified and directed. Note: Excavation in post hole and PCC work shall be measured and paid separately

S&F in repair direction sign board of any size with 2mm thick aluminium composite panel comprising both side high intensity prismatic grade retro reflective sheeting as base and with cut out massage (legends borders letters / numerals etc) as directed with high intensity prismatic grade retro reflective sheeting both side of boards with epoxy powder coating, including fixed over framed work of stainless steel complete all as specified and directed. The following specification for sign board to be used:- (i) Paper used for printing should be 170 GSM 3M Reflective Vinyl. (ii) Printing of letter with Mutoh Eco Solvent. (iii) Base of Material shall be used 3mm Alcabond.

S&F in repairs of solar Road Studs/ cat eye 125mmx125mmx25mm. Solar road stud made from aluminium alloy, solar powered by monocrystal solar panel, fix with epoxy or other suitable adhesives as per manufacturer instructions and fwd specificatio :- (i) Battery type - one high capacity Ni-Cd rechargeable battery. (ii) Back up time shall not be less than 12 hours of continuous lighting at night. (iii) Designed to bear 25 Tonnes load. Make : Road star Model No. GSR-909 or equivalent approved.

S&F in repair of Vertical Guide Post/ Delineator consisting of retro reflective unit and fixing as per manufacturer's instructions complete all as specified and directed. Make : Road star Model No. RSSP-750/3 or equivalent approved.

S&F in repair convex mirror of 800 mm dia size made of polycarbonate plastic, outdoor type mounted on stainless steel frame and fixed at a suitable height including all fixing arrangements complete all as specified and directed. Make : Road star Model No. RSCM-80 or equivalent approved.

Demolition of PCC of any description and in any position not otherwise specifically provided including removing the demolished material out side MoD land in low laying area complete all as specified and as directed.

S&F in repair at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with CM 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment PCC kerb stone shall be approved by Engineer-in-charge.

M&L for applying two coat of synthetic enamel paint over concrete/plastered surfaces along with prepration of new or previously untreated surfaces of any description over 10cm width or girth with one coat of priming paints plaster coat complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for factory made rubber pressed polished with coating material, concrete coloured designer interlocking paver block with Grey cement and pigment, any shape and size, 60 mm thickness, M-35 grade over and including 40mm sand cushioning layer and dismantling of old unserviceable interlocking paver block with sand cushioning complete all as specified and as directed.

M&L for Rubber pressed coloured chequered concrete paving/ tiles 30cmx30cmx25mm thick, set, jointed and pointed in neat cement slurry in floors using with grey cement and pigment over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed

M&L for dismantling of floor tiles / hearth of wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish of the premises etc complete all as specified and directed.

M&L for glazed ceramic designer coloured tiles in stones / Mat finsih of size 450x300x7-8 mm thick on vertical surface as in skirting/dado set and jointed in neat cement slurry and pointing in white or coloured cement to match the surface over 10mm thick rendering in CM (1:4) on brick wall complete all as specified and directed.

Demolition of brick work built in cement mortar of any description complete all as specified and as directed.

Material and labour for brick masonry with sub class `B` brick (old size) straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed

All as per item No 20.00 above but except bricks.

M&L for 15mm thick randering in CM 1:4 on brick/concrete surface finished even and smooth with out using extra cement.complete all as specified & directed.

M&L for prepration of newly plastered surface and apply two coat of cement base paint over a coat of primer complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc. 50 mtr complete all as specified and directed.

M&L for PCC 1:2:4 type B2 using 20 mm graded mechanically crushed stone aggregate as in filling in post holes, walls or retaining walls, any thickness, size or shape all as specified.

DR Buildcon

Som Builders