MISC REPAIRS TO KITCHEN, BATHROOM INCLUDING ALLIED WORKS AND ROOF REPAIR IN AREA UNDER AGE B/R-II AT AFS ADAMPUR

M & L for providing PCC 1:3 :6 type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats complete all as specified and as directed .

M&L for PCC type E-2 (1:5:10), using 40 mm graded crushed stone aggregates as in filling & mass concrete, complete all as specified and directed.

M&L for Reinforced cement concrete, type B-1, (1:2:4), using 20 mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, and in shelves and the like complete all as specified and directed.

M&L for Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified and directed.

M&L for Brick work (Except bricks) as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified and directed.

M&L for Cutting chases pinning in making good to facing where required and pointing in cement mortar (1:3) for concealed water tubing in brick walls cutting n.exc 10 cm girth. complete all as specified and directed.

M & L for Granite 15-18 mm (of any type) work (table rubbed and polished) thick in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including 20 mm thick screed bed in CM (1:6) for laying of granite slab & pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, etc complete all as specified and directed.

M&L for Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) with fair finished surfaces of concrete, complete all as specified and directed.

S & F 35 mm 2nd class hard wood factory made, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) etc complete all as specified and directed.

M&L for Factory made, 35 mm thick, second class hard wood, plain framed, hammer marked, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for Factory made, 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides,ISI marked, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sq.m each and removing from site all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sq.m but not exceeding 4.00 Sq.m each and removing from site all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each and removing from site all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each, including stacking at directed location and refixing the same on original or new location after resecuring or easing & adjusting, complete all as specified and directed.

M&L for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded wood grain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and wood grain colour PVC sheet for top rail, lock rail and bottom rail, panelling of wood grain colour PVC sheet to be fitted in the MS frame welded / sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement as specified in SSR Part II, complete all all as specified and as directed.

M&L for Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick wood grain colour PVC sheet reinforced with mild steel square tube, suppling & fixing in opening, complete all as specified and directed.

S&F, Aluminium anodised barrel tower bolt of extruded section 150 mm long, ISI marked, complete all as specified and directed.

S&F, Aluminium alloy, anodised, ISI marked sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300 mm long, complete all as specified and directed.

S & F for Butt hinges, extruded Stainless steel with galvanised mild steel hinge pin, anodised and fixed, type B-21, size of hinges in 100 mm, etc complete all as spd and directed.

S & F 300 mm long mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed.

S & F 125 mm size, aluminium anodized handles, cast type complete all as specified and directed.

S&F in repair Stainless steel conduit 20 mm bore, cut to size and erected in position including provision SS brackets & SS decorative type finial (Two nos for each opening) complete all as specified and directed.

S & F in repair Brass chromium plated, tubular towel rails 20 mm dia, D- type, 60 cm long between flanges, completed all as specified and directed.

S & F for Stainless steel wire cloth,0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, etc complete all as specified and directed..

S&F, Framed mild steel work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S & F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

S&F, Factory made pre painted pressed steel frames, conforming to IS, having profile 105 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete, all as specified and directed.

S&F, Factory made pre painted pressed steel frames, conforming to IS, having profile 165 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete, all as specified and directed.

M&L for Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified and directed.

M&L for 25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per sq. metre, etc completed all as specified.

M & L for 7 to 8 mm thick Coloured Glazed ceramic tiles of size and pattern as approved by Engineer-in-charge , as in vertical surface such as skirting , dados and riser to steps etc set and jointed in neat cement slurry and pointed in white or colour cement to match over and including backing coat of 10 mm thick in cement mortar 1:4 complete all as specified and directed.

M&L for Coloured Glazed ceramic tiles in vertical surface of size 600mmx300mm and 6-7 mm thick of colour and pattern as approved by Engineer-in-charge , set and jointed in neat cement slurry and pointed in white or colour cement to match including Rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces as backing coat complete all as specified and directed.

M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20 mm thick Screed bed or bedding layer of mortar for laying floor finishes in CM 1:6 complete all as specified and directed.

M&L Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20 mm thick Screed bed or bedding layer of mortar for laying floor finishes in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling or stone chips including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, etc completed all as specified.

M&L for repairing of RCC projection chhajjas, roof, facia etc by necessary preparation. Scraping cutting, chiselling de-rusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC with cement concrete (1:1.5:3) using 20mm graded stone aggregate and reinforcement with welded mesh of weight 2 Kg per Sqm but n.exc 3 Kg per Sqm (if reqd) with or without facia and finished with cement and sand mortar (1:3) using coarse sand and work in patches area n.exc 5 Sqm and thickness of RCC member n.exc 70mm including necessary formwork and applying two coats of finishes to match with the existing surfaces at any height complete all as specified and as directed by Engr-in-Charge. (The rate quoted by the contractor shall included for scaffolding and necessary formwork upto triple storey bldg).

M & L for rendering 10 mm thick on brick or concrete surface of ceiling finished fair & even in CM 1:3 complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surface finished fair & even in CM 1:6 complete all as specified and directed.

M&L for 15 mm thick rendering in 1:4 CM with using 3% WPC as in sunken portion complete all as specified and directed

M & L for rendering 15 mm thick on fair faces of brick wall with mixing WPC @ 3% by wt of cement finished fair & even in CM 1:4 upto three storey complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc completed all as specified.

Supply only water proofing compound, ISI marked, complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces of any description complete all as specified and applying Two coats of interior acrylic distemper over and including a coat of wall care putty and primer complete all as specified and directed

M&L for two coat of white wash on old wall surfaces, including preparation of surfaces, complete all as specified and directed

M&L for complete removal of existing treatment of any description, including preparation of wall surfaces of any description complete all as specified and applying Two coats of interior acrylic distemper over and including a coat of wall care putty and acrylic emulsion primer complete all as specified and directed.

M & L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash on ceiling, complete all as specified and directed.

M & L for One coat of white wash on old ceiling surfaces, including preparation of surfaces, complete all as specified.

Supplied only for 4 mm thick, Sheet glass, ordinary quality, in squares n exc 0.5 sq. m each pane, etc completed all as specified.

Supplied only for 4 mm thick, Figured glass, pin head type in squares n exc 0.5 sq.m each pane, etc completed all as specified.

M&L for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed .

M&L for applying one coat (finishing coat) of synthetic enamel paint, including preparation of old painted wood and wood based surfaces of any description not other wise described over 10cm width or girth and complete all as specified and directed .

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamelled paint over one coat of red oxide primer complete all as specified and directed .

M&L for applying one coat (finishing coat) of synthetic enamel paint including preparation of old painted steel & iron surfaces of any description not other wise described over 10cm width or girth, complete all as specified and directed ..

S & F in repair GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid in floors 15mm bore complete all as specified and directed.

S & F in repair tubes 20 mm bore dia, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Dismantling water tanks P.V.C. or R.C.C. capacity exc 250 ltr & n exc 500 ltr and removing to store, etc complete all as specified and directed .

S&F 500 ltrs rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Disconnecting existing tanks, Capacity exc. 250 ltr but not exc. 500 ltr , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position after cleaning the tank complete all as specified and directed.

S&F in repairs bib tap, cast copper alloy with capstan head, CP fancy type with long body shank, screwed down with high pressure screwed for iron pipe & fixed 15mm bore, complete all as specified and directed.

S&F in repair Pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed .

S&F in repairs stop cock/angle cock fancy type CP with long shank cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed.

S&F in repairs concealed stop cock type CP with long shank cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore complete all as specified and directed.

S & F in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, Bore dia of pipe in 20 mm, etc complete all as specified and directed .

S&F in repair grating doom 100mm dia size with PTMT complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified and as directed.

S & F in repair for 100mm cast iron sanitary P or S trap to fit WC out-let, etc complete all as specified and directed.

S & F in repair for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors , bore of pipe in 75 mm, etc complete all as specified and directed.

S & F in repair for PVC (SWR) bends any radius, bore of pipe in 75 mm, etc complete all as specified and directed.

S & F in repair for 75 mm cast iron sanitary connections—short connections pipe of length upto 300 mm, etc complete all as specified and directed..

S & F in repair for 100 mm cast iron sanitary connections—short connections pipe of length upto 300 mm, etc complete all as specified and directed.

S & F in repair 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4 ) complete all as specified and directed.

S & F in repair 75mm dia PVC floor trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4 ) complete all as specified and directed.

S & F in repair PVC (SWR) pipes single socketed, in any length with or without rubber ring joints, fixed to walls, bore of pipe in 150 mm, etc complete all as specified and directed.

S & F in repair for PVC (SWR) bends/shoe any radius, bore of pipe in 150 mm, etc complete all as specified and directed.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe etc. complete including making good to floor, complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400 mm aps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F in repair brass chromium plated shower roses with swivel joints, 125 mm size in square with CP long shank arm including fixing to steel pipe or union, complete all as specified and as directed.

S&F in repair Stainless steel sink with drainage board made out of 1.00mm thick sheet for kitchen or laboratory with plug , waste pipe ,washers including cantilever cast iron brackets, connecting union etc overall size 940mm x 460mm x 203mm with bowl size 405mm x 354mm x 203mm complete all as specified and directed.

S&F in repairs PVC flushing cistern 10 ltr capacity valve less symphonic action type low level with and incl ball valve float & handle, flush pipe, waste pipe & brackets complete set complete all as specified and directed.

Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided for, cement concrete, etc complete all as specified and directed.

Demolition of reinforced cement concrete as in chimney, Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work complete all as specified and directed.

M&L for applying two coats of two component elastomeric acrylic polymer modified cementations waterproofing coating, Smart care Ultra block 2K or equivalent, having 215% elongation as per ASTMD-2370, resisting 5 bars hydrostatic pressure as per DIN 1048, crack binding upto 3.50 mm as per EN 1062-7 and sprinkling dry fine sand over wet second coating complete, as per manufactures specifications. NOTE: - Unless otherwise recommended by manufacturer, the mixing ratio of the components shall be 6 parts of powder and 4 parts liquid without any water addition in the mixing,

M&L for Cleaning the surface and made free of dirt, foreign particles, laitance followed by grinding all protrusions to make surface modulated. Thereafter, inspection for cracks on the surface caused by thermal expansion contraction. Cutting the grooves with suitable cutter machine in "v" groove filled with Repair mortar/Micro concrete/General purpose grout as recommended proportionally as per recommendation of manufacturer and applying FOSROC nitoproof 650PU over a priming coat of FOSROC Nitoproof WB primer or equivalent product of Asian paints, M/s MC Bauchemie/CIPY/ SIKA/ Pidilite/ DR Fixit/ Thermex STP applied as per manufacturers instructions. Further provide a polypropylene/ polyester non woven geotextile fabric of 150 GSM. Followed by cement screed 15mm in CM (1:4) in slope, over that 20mm thick Terracotta burnt tiles are laid. While laying the tiles, care should be taken to see that joints are thoroughly filled with FOSROC Nitotile grout polymer based joint mortar or equivalent product of Asian paints M/s MC Bauchemie/CIPY/ SIKA/ Pidilite/ DR Fixit/ Thermex STP as per manufacturers instructions. Note: Tiles should be measured and paid separately in respective item.

Supply and fixing heat resistant terrace tiles (300mm x 300mm x 20mm) with SRI (solar refractive index)> 0.70 and initial remittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 and grouting the joints with Epoxy mix , including rubbing and polishing of the surface upto 3 cuts complete , including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (20 mm graded aggregate)as padding in roof including necessary formwork complete all as specified and directed

M&L for cement 1:2:4, type B0, using 12.5 mm aggregate providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified and directed

M&L for 75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, and joints shall be sealed with joint sealing compound grade 'A' complete all as specified and directed.

M & L for 100 mm thick, Cement concrete type D-2, 1:4:8 (40mm graded aggregate), etc completed all as specified and directed.

M & L for Chequered cement concrete tiles 25mm thick of any size and shape, set, jointed and pointed in neat cement slurry in floors, with grey cement and no pigment including 20 mm thick screed bed in CM (1:6) , etc completed all as specified and directed.

M & L for 40 mm thick brick tiles are bedded over 15 mm thick cement mortar (1:4), and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on APP membrane completed all as specified and directed.

M & L for 40 mm thick brick tiles (Except Tiles) are bedded over 15 mm thick cement mortar (1:4), and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on APP membrane completed all as specified and directed.

M & L for Raking out joints/ pointing in cement mortar to brick work or brick tiles, laid flat, in floors, surface channels, roofs, etc complete all as specified and directed.

M & L for Flush pointing to bricks laid flat or brick tiles in paving in cement mortar 1:4 complete all as specified and directed.

Steel windows made of MS sheet 1.25 mm thick box type (primer coated) ERW hollow ‘P’ section of size 60 mm x 25 mm single rebate comprises of skeleton shutter ERW sec 50 x 20 mm & 1 mm thick & openable leaf consisting two Nos sash bars of ‘T’ section 20 x 3 mm complete welded to frame including cutting holes & making good dismantled portion in PCC 1:2: 4 type B1 four Nos for each window including following fitting welded to shutter ;- (a) Hold fast 150 mm long 12 mm x 3 mm made to shape -04 Nos (b) Handle of ‘Z’ section 20 x 25 mm , 100 mm long 01 Nos each leaf. (c) MS tower bolt 150 mm long 02 Nos each leaf. (d) ‘Z’ section 20 x 25 mm , 100 mm stopper-01 Nos each leaf. (e) Cleat 55 mm long of hollow square 15 x 20 x 63 mm welded to hinges-01 Nos per leaf. (f) MS box type hinges of size 75 x 12 mm -02 Nos per leaf. (g) Fabrication & fixing complete all as specified and directed.

All as per item above here-in-before but with out sash bars

S & F in repair floor door stopper of aluminium alloy body double leg 75-80 mm long with rubber stopper at bottom complete all as specified and directed.

S&F in repair 450 mm long Glass Shelf fixed with and including chromium plated brass screws and wooden/ plastic cleats complete all as specified and directed.

S&F in repair steel plate rack made of stainless steel 0.61 mm thick over all size 600mmX750mm complete all as specified and directed by Engineer-in-charge.

S&F in repair Stainless steel Soap dish complete all as specified and directed.

M&L for Preparation of newly plastered wall surfaces of any description complete all as specified and applying Two coats of exterior acrylic emulsion over and including a coat of exterior (water based) primer complete all as specified and directed

M&L for Uprooting tree/plants upto 30 cm girth from wall or any part of building upto double storey buildings completely to the entire satisfaction of Engineer-in-Charge, making good the disturbed portion and filling holes in cement mortar (1:3) or PCC (1:2:4) type B-1 using 20mm graded stone aggregate to match with existing surfaces and removal of rubbish outside MOD land complete all as specified and directed.

Dismantling Brick tiles or terracing tiles, single layer on roofs, etc complete all as specified and directed

Demolition of mud puska in roof any thickness incl plastering & leeping removed complete all as specified and directed.

Notes: Amount of credit for retrieved materials is mentioned in tender documents in pdf form which will be deducted while acceptance of tender offline.