REPAIR/REPLACEMENT OF DEFECTIVE SPARES AND COMPREHENSIVE MAINTENANCE OF CRANES AND HOISTS LOCATED IN CVD, COD, 35 INF BDE UNDER GE(U) P AND M DELHI CANTT-10

Amount

Comprehensive preventive maintenance by technically qualified technician and rendering operationally EOT crane of capacity as mentioned below including assemblies inspection and maintenance of including checking / tightening of all nut , bolt & breaks any type any size complete system, adjusting etc of all breaks motions and VFD /VVVF drive adjustment setting of EOT / HOT cranes with having single or double girder type and providing greasing & oiling of traveling / moving parts of crane with connecting motor girder parts for movement of crane hoist / long / cross traveling and including maintaining the controlling of speed / creeping micro speed of motors with minor maint / repair electrically operated main control panel wire with connecting control wiring system consisting of main switch, step down transformer, contactor, HRC fuse, VFD, PLR, control pendent ,wire rope with break drum unit, gear box unit , oil levels, motor bed / foot ,electrical control cable, motor terminal, end cable carriage trolly , motor shaft, bush flange bearing with lathe work ,chain pulley block, ratchet clutch, gear block, chain wheel, chain etc and including locating the defect or fault and rectification of the fault and rectification of oil leakage etc any type any size and replacement of defected nut, bolt & washer and making it soundless/sound proof and after trails testing run of crane for smooth functioning / operation satisfactorily of the following mentioned capacity cranes/Hoist complete all as specified and as directed. Details of EOT Crane (i) EOT crane of 50/10 Ton capacity located at CVD- 01 No. (Make of M/s John Smith) Total - 01 No X 6 Month = 06 month

All as per srl item No 01 here-in-before but EOT Crane/Hoist of capacity mentioned as under complete all as specified and as directed. (i) EOT crane of 10 Ton capacity located at CVD- 01 No. ( Make of M/s Hindustan Liver) Total - 01 Nos X 6 Month= 06 month

All as per srl item No 01 here-in-before but EOT Crane/Hoist of capacity mentioned as under complete all as specified and as directed. (i) EOT crane of 01 Ton capacity located at COD- 05 Nos. ( Make of M/s Morris) (ii) EOT crane of 02 Ton capacity located at 35 INF Bde - 01 No ( Make of USGC) (iii) EOT crane of 05 Ton capacity located at CVD- 01 No. ( Make of M/s Hindustan Liver) Total - 07 Nos X 06 months = 42 Month Note for item No 1 to 3 :- (i) Inspection checking decarbonising & tightning of electrical connection in total system including replacement of thimbles etc. (ii) Inspection & checking of fuses, setting & tightning the same as per their capacity. (iii) Inspection and setting of voltage system including replacement of fused indicating lamp etc. (iv) Spares for EOT crane will be measured and paid seperately as given in Section II of BOQ. (v) Contractor will carry out comprehensive maintenance once in a month for six (06) months and maintain the record of same as per the performa of monthly maintenance check enclosed in the tender documents.The same shall be forwarded alongwith RAR failing which no payment shall be released to the contractor. (vi) Contracor will ensure serviceability and safety of crane during his each visit by way of maintining job card duly signed by Engr-in-Charge and JE E/M. (vii) The contractor will also send Technician on call basis in case of any fault. Fault to be rectified within 8hrs of receipt of complaint failing which Rs 500/- per day will be deducted till rectification of defect.

Note for item No 1 to 3 (Contd...):- (viii) Rates of all consumables such as lubricant, gear box oil, thrustor brake oil , nut bolt, split pins, bushes, gasket , Push Buttorn for pendent are deemed to be included in the quoted rates. (ix) The maintenance & repair under this contract shall be done through MoU issued by any one of OEM i.e. M/s Rockwell Hoisto Cranes Pvt Ltd, M/s Poineer Cranes, M/s Hercules Hoisto, M/s Turbo Fergusan (India) Pvt Ltd, M/s Cranex, M/s USGC, M/s Garlik, M/s Morris, M/s Hindustan Liver, M/s Grip Engineers, M/s Meta feb, M/s JPSENT. The contractor will have to submit MoU on stamp paper of Rs 100/- duly notarized, as per specified Performa within fifteen days of acceptance of tender, failing which the contract will be liable to be cancelled and work shall be executed as per policy in vogue. (x) OEM’s are exempted from production of MoU, if they participate in bidding directly, subject to fulfilling requirements as mentioned in the tender. It may also be noted that, if the OEM’s issues MoU for participation of other bidder than OEM’s bid will be rejected upon his direct participation in the tendering process.

Material and labour for fixing of shrouded copper conductor busbar 160Amp TPN (4 Bar) "W" Type with PVC sleeves RYBG DSL 4 Bar , hanger,clamps,anchor clamps, power feed kit and caps, joining tool with towing arm, end cap complete and including MS fabricated supports for mounting of conductors made out of mild steel angle of size 40x40x5 mm and 450 mm long and necessary welding work complete and including two coats of synthetic enamel back paint cover a coat of red oxide primer and supports to be provided at every one mtr distance complete all as all as specified and as directed .

Supply and fixing in replacement of 2 way lever type limit switch 2 contact type LS/2SH/2 in IP 54 Enclosure suitable for Crane operation complete bracket and welding work required for fixing complete all as specified and as directed.

Supply and fixing in replacement of Rotary type geared limit switch ratio 48:1 with 4 contacts type RLS/48/4SE.suitable for Crane operation or as per sample complete all fitting on existing place, complete all as specified and as directed.

Supply and fixing in replacement of one way type gravity limit switch alonwith counter weight operated shunt limit switch type CWLS/ISH/2 with IP54 enclosure and suitable for crane operation or as per sample complete all fitting on existing place complete all as specified and as directed.

Supply & fixing in replacement Master Contactor 5 Step Type CMN/7 No of Contact 7 Spring return Type in Sheet Steel Enclosure suitable for crane operation or as per sample complete all as specified and as directed.

Supply & fixing in replacement Master Contactor 4 Step Type CMN/6 No of Contact 6 Spring Retun Type in Sheet Steel Enclosure suitable for crane operation or as per sample complete all as specified and as directed.

Material and labour for cutting/fabrication ,fixing & welding of MS angle iron of size as per site requirement for fixing chequered plates/making ladders, supports fixing brackets etc including bracing ,supports ,clamps,and back plates fabricated fron structural steel section including Nits & Bolts ,washers,welding,bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one coat of Red Oxide Zinc chrome primer and two coat of alumunium paint as per existing colour complete all specifed and as directed. Note:- The cost of PCC work for fixing of structure/ladders, if needed is deemed to be included in rate quoted by contractor.

Material and labour for phase indication lamp with indication colour Red,Yellow and Blue for DSL busbar of crane with best quality LED lamps , visibility range upto 200 mtr, including ss powder coated enclosure and necessary welding and bracket for fixing indicator on the bus bar complete all as specified and as directed.

Dismantling & taking down brake drum of size 100-400mm dia by disconnceting it from brake drum assembly and taking it to workshop for sanding the plain surface in order to make grip for brake shoe for holding /releasing the brake of the Crane and after making a good fixing it at the same position complete all as specified and as directed.

All as per srl item No 13 here-in-before but motor of capacity 5.0 HP /3.7 KW ,3 phase, 415 volts ,50 Hz complete all as specified and directed.

All as per srl item No 13 here-in-before but motor of capacity 3.0 HP / 2.2 KW ,3 phase, 415 volts ,50 Hz complete all as specified and as directed.

Dismantling and removing of damaged & worn out mild steel wheel ( Long /Cross travel) including complete wheel assembly i.e wheel shaft, bearing housing ,bearing and connected accessories complete of EOT crane 02 Ton to 50 Ton capacity at the height of 20 feet and above complete all as specified and as directed. Note:- (i) Necessary safety measures to be taken by the contractor while dismantling and fixing the crane wheels. (ii) Any damage to govt property while executing the work is to be make good by the contractor. (iii) The cost of scaffolding arrangement laddars,safety belt,lifting jacks,and T&P used while working in the crane will be borne by the contractor itself.

Supply,fixing and testing of traveling for Cross travel Mild steel forged cast alloy wheel assembly complete with new driving axel,new spacers,new shaft,new bearing with housing of suitable size nut 7 bolts,washers and packing materials etc as per existing specifiaction for EOT Crane 2 to 5 Tons capacity complete all as specified and as directed. (Make:- As per ISI Marked)

Supply,fixing and testing of traveling for Long travel Mild steel forged cast alloy wheel assembly complete with new driving axel, new spacers, new shaft, new bearing with housing of suitable size nut & bolts, washers and packing materials etc as per existing specifiaction for EOT Crane 2 to 5 Tons capacity complete all as specified and as directed. (Make:- As per ISI Marked)

Supply,fixing and testing of traveling for Cross travel Mild steel forged cast alloy wheel assembly complete with new driving axel,new spacers,new shaft,new bearing with housing of suitable size nut 7 bolts,washers and packing materials etc as per existing specifiaction for EOT Crane 10 to 50 Tons capacity complete all as specified and as directed. (Make:- As per ISI Marked)

Supply,fixing and testing of traveling for Long travel Mild steel forged cast alloy wheel assembly complete with new driving axel, new spacers, new shaft, new bearing with housing of suitable size nut & bolts, washers and packing materials etc as per existing specifiaction for EOT Crane 10 to 50 Tons capacity complete all as specified and as directed. (Make:- As per ISI Marked)

Material and labour for alignment of EOT Crane rail tracks on both sides of the way approx 20 Ft height and above from the ground floor, including gas cutting, welding and grinding, fish plates , nuts & Bolts for smooth movement of LT Motion of the EOT Cranes ( approx one side length of track 100-150 RM ) complete all as specified and as directed. Note:- (i) Necessary safety measures to be taken by the contractor while working on rail tracks. (ii) The cost of scaffolding arrangement laddars,safety belt,lifting ,and T&P used during the alignment/working on rail track will borne by the contractor itself.

Servicing of Gear Box assembly of LT/CT/Hoist complete at any height and replacement of gear box oil seal, cover packing seal , gear box ball bearing, gear oil (90W/40) etc or other defected connecting parts as required at site as per existing sample/type and making it oil leak proof and sound less proof complete and including testing for EOT crane upto 10 ton capacity complete all as specified and as directed. Note- (i) Servicing of gear box of any type and testing run work will be carried out by well qualified technician having good experience in the repairing field of EOT / HOT Cranes/Hoist or as approved by Engineer-in-Charge. (ii) Necessary safety measures to be taken by the contractor while dismantling and fixing the gear box. (iii) Any damage to govt property while executing the work is to be make good by the contractor.

All as per srl item No 22 here-in-before but EOT Crane of 50 Ton capacity complete all as specified and as directed.

Material and labour for preparing surface and painting of EOT cranes of any capacity complete including double girder beam, trolly, foot path, railing path, motors , shaft, ladder and Gear Box and other connecetd parts of crane by scraping, cleaning, using wire brush, sand paper etc, and painting complete with two coats of synthetic enamel paint of golden yellow/ tractor orange / gray colour as per existing colour code over one coat of zinc chrome primer ( LT Span of the cranes not more than 30 metres) complete all as specified and as directed. Note:-(i) Necessary safety measures to be taken by the contractor while painting the cranes. (ii) Any damage to govt property while executing the work is to be make good by the contractor. (iii) The cost of scaffolding arrangement laddars,safety belt,lifting ,and T&P used while painting in the crane will borne by the contractor itself. (iv) Marking on the display board of the Crane i.e Make of cranes , Capacity , MES No/Sr No and Installtion Year in Black paint completed.

Supplying, Laying ,and fixing in replacement of XLPE insulated armoured heavy duty electric cable of the following size, 1100 Volts grade, with stranded aluminium conductor served with an inner sheathing of PVC tape armoured with GI wire and over all PVC sheathed in laid trenches/ passing through pipe/duct/road crossing/surface of wall/in hume pipe etc including fixing hardware,clamps,gland, thimble and making good the damaged surfaces etc complete all as specified and as directed.

95 Sqmm 3.5 core

35 Sqmm 3.5 core

Supply and fixing in replacement of defective DC Disc Brake Type Fail Safe Brake Model SLDC 150, 75 Watt. Torge 2 KGM , 3 Phase 415 V complete fitting as per existing loaction complete all as specified and as directed.

Supply and fixing in replacement of Current Collector 100A (Suitable for shrouded busbar) with 1mtr PVC copper cable for connection including bracket , welding etc complete all as specified and as directed.

Supply and fixing in replacement of Current Collector 160A (Suitable for shrouded busbar) with 1mtr PVC copper cable for coonection including bracket , welding etc for complete all as specified and as directed.

Supply and fixing in replacement of Pneumatic Time Delay Relay 0-60 Sec Coil Voltage 110 V AC complete all as specified and as directed.

Supply and fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 25 Amp. ML-1.5 with 2 N.O. + 2 N.C. Aux Contact Coil Voltage 110V AC complete all as specified and as directed.

Supply and fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 32 Amp. ML-2 with 2 N.O. + 2 N.C. Aux Contact Coil Voltage 110V AC complete all as specified and as directed.

Supply and fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 40 Amp. ML-3 with 2 N.O. + 2 N.C. Aux Contact Coil Voltage 110V AC complete all as specified and as directed.

Supply and fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 70 Amp. ML-4 with 2 N.O. + 2 N.C. Aux Contact Coil Voltage 110V AC complete all as specified and as directed.

Supply and fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 110A Amp. ML-6 with 2 N.O. + 2 N.C. Aux Contact Coil Voltage 110V AC complete all as specified and as directed.

Supply and fixing in replacement of Three pole power contactor 3 phase,415 Volt MNX 185 with 2NO+2NC complete all as specified and as directed.

Supply and fixing in replacement of Three pole power contactor 3 phase,415 Volt MNX 140 with 2NO+2NC complete all as specified and as directed.

Supply and fixing in replacement of Three pole power contactor 3 phase,415 Volt MNX 32 with 1NO or 1 NC complete all as specified and as directed.

Supply and fixing in replacement of Three pole power contactor 3 phase,415 Volt MNX 25 with 1NO or 1 NC complete all as specified and as directed.

Supply and fixing in replacement of power contactor 3 phase MNX series type or as per existing sample / model of rated capacity 6 Amp to 9 Amp 415volts along with suitable rating of NC/NO type Auxiliary contactor block complete all as specified and as directed.

Supply and fixing in replacement of 3 core 1.5 Sqmm PVC insulated & round sheathed bright annealed copper conductor cable for voltage grade 1100 V as per IS: 694 complete all as specified and as directed.

Supply and fixing in replacement of 3 core 2.5 Sqmm PVC insulated & round sheathed bright annealed copper conductor cable for voltage grade 1100 V as per IS: 694 complete all as specified and as directed.

Supply and fixing in replacement of 3 core 4.0 Sqmm PVC insulated & round sheathed bright annealed copper conductor cable for voltage grade 1100 V as per IS: 694 complete all as specified and as directed.

Supply and replacement of 3 core 6.0 Sqmm PVC insulated & round sheathed bright annealed copper conductor cable for voltage grade 1100 V as per IS: 694 complete all as specified and as directed.

Supply & fixing in replacement of FRLS cable PVC insulated & PVC round sheathed bright annealed copper conductor flexible cable of size 8 Core 1.5 Sqmm voltage grade upto 1100 V as per IS 694/1990 complete all as specified and as directed.

Supply & fixing in replacement of FRLS cable PVC insulated & PVC round sheathed bright annealed copper conductor flexible cable of size 16 Core 1.5 Sqmm voltage grade upto 1100 V as per IS 694/1990 complete all as specified and as directed.

Supply and fixing in replacement of cable resting trolly MS four wheel (with four ball Bearing) type suitable for EOT Crane or as per sample and necessary welding work complete all as specified and as directed.

Supply and fixing in replacement of Bearing with plumber Block No. SYJ80TF of complete mounting in existing place alonwith any retrofit work complete all as specified and as directed.

Supply & fixing in replacement of Step Down Transformer double bound type 415/110V AC 500VA complete all as specified and as directed.

Supply & fixing in replacement of Step Down Transformer double bound type 415/220V AC 1KVA complete all as specified and as directed.

Supply and fixing in replacement of Automatic Phase Sequence Corrector 34.0 HP 3 Phase 415 V. AC in CRCA Sheet Enclosure 2 mm Thick duly Powder Coated Indoor Type self standing / wall mounting,including connecting cable in/out complete all as specified and as directed.

Supply and fixing in replacement of Automatic Phase Sequence Corrector 25.0 HP 3 Phase 415 V. AC in CRCA Sheet Enclosure 2 mm Thick duly Powder Coated Indoor Type self standing / wall mounting,connecting cable in/out complete all as specified and as directed.

Supply and fixing in replacement of Automatic Phase Sequence Corrector 17.5 HP 3 Phase 415 V. AC in CRCA Sheet Enclosure 2 mm Thick duly Powder Coated Indoor Type self standing / wall mounting,connecting cable in/out complete all as specified and as directed.

Supply and fixing in replacement of Floating shaft made out EN-8 material horizontal straight medium carbon steel with key way slot as per existing sample for LT/CT of EOT crane capcity upto 10 Ton complete all as specified and as directed.

Material and labour for taking down of unserviceable motor from EOT crane and including transporting and re-winding of electric motor of capacity 15.0 HP/ 11.0 KW, 3 phase 415 volts, with super enameled copper conductor wire as per existing size/gauge including making varnishing drying and connecting fixing accessories etc including refixing on same position and testing on load complete all as specified and as directed.

All as per srl item No 56 here-in-before but motor of capacity 7.5 HP/5.5 KW complete all as specified and as directed.

All as per srl item No 56 here-in-before but motor of capacity 2 HP/ 1.5 KW complete all as specified and as directed.

Supply, installation and testing of Hoist assembly complete with including parts i.e lifting motor, travelling motor,rope drum ,gear,shaft , limit switches , wheels, wiring etc.as per existing specification complete making good and smooth functioning for hoist assembly of capacity 01 Ton Electric Hoist make of M/s Morris including taking down old unserviceable one complete all as specified and as directed. Note:- Steel wire rope and bottom block hook are measured and paid seperaterly.

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 100-18 Kg , alongwith suitable brake shoe liner with ribets complete, required any retrofit work for fitting in existing foundation of thrustor brake complete all as specified and as directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 150-18 Kg , alongwith suitable brake shoe liner with ribets complete, required any retrofit work for fitting in existing foundation of thrustor brake complete all as specified and as directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 200-18 Kg , alongwith suitable brake shoe liner with ribets complete, required any retrofit work for fitting in existing foundation of thrustor brake complete all as specified and as directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 250 -18 Kg , alongwith suitable brake shoe liner with ribets complete, required any retrofit work for fitting in existing foundation of thrustor brake complete all as specified and as directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 300-34 Kg , alongwith suitable brake shoe liner with ribets complete, required any retrofit work for fitting in existing foundation of thrustor brake complete all as specified and as directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 400-34 Kg , alongwith suitable brake shoe liner with ribets complete, required any retrofit work for fitting in existing foundation of thrustor brake complete all as specified and as directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor 18 Kg , 415 Volts, 3 phase power supply alongwith standard grade brake oil filling and required any retrofit work for fitting in existing foundation complete all as specified and as directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor 34 Kg , 415 Volts, 3 phase power supply alongwith standard grade brake oil filling and required any retrofit work for fitting in existing foundation complete all as specified and as directed.

Supply & fixing in replacement of Protective Cum Control panel for 2 Ton EOT crane indoor type, made out of CRCA sheet 2mm thick, compartmental type, dully powder coated, self-standing / wall mounting and complete internal wiring by PVC flexible copper cable and ferruels. Control wiring not less than 1.5sqmm and power wiring not less 2sqmm with incoming and outgoing cable connection and comprising the following items:- a). MCCB 3P, 100A , 25KA, Qty : - 1No b). MCB 3P, 63A 415Volt Qty : - 2Nos. c). MCB 3P, 16A, 415 Volt. Qty : - 3Nos. d). MCB 2P, 4A, 230 Volt Qty : - 2Nos. e). MCB 2P, 6-10A, 230V Qty : - 2Nos. f) Step Down Transformer double bound type 415/110V AC 500VA – Qty-01 No g) 3 Pole Power Contactor 3 phase 415V ML-2 with 2 NO. + 2 NC.Aux Coil Voltage 110V AC : - 5 Nos. h) 3 Pole Power Contactor 3 phase 415V ML-1.5 with 2NO. + 2 NC. Aux Coil Voltage 110V AC - 5 Nos. i) Thermal Overload relay ML-2 relay range 6-10A .Qty : - 2 Nos. j ) Thermal Overload relay ML-2 relay range 3-5A Qty : - 3 Nos. k) Thermal Overload relay ML-2 relay range 9-15A Qty : - 1 No. l) Single Phase Preventer 3 Phase 415V Qty : - 1Nos. m) Step Down Transformer 415/220 V AC 1KVA Double Bound. Qty : - 1No. n)Connector Block of suitable sizes. 1 Set. o) Crane operate rotory swich ON/OFF Qty : - 2Nos.

Supply & fixing in replacement of Protective Cum Control panel for 1 Ton Wire rope electric hoist made out of CRCA sheet 2mm thick compartmental type dully powder coated , wall mounting and complete internal wiring by PVC flexible copper cable and ferruels and comprising the following items a). MCB 3P 63A 415V . : - 1Nos. b). MCB 3P 16A 415V. : - 2Nos. c). MCB 2P 4A 230 V. : - 2Nos. d). MCB 2P 6-10A 230V. : - 2Nos. e) Step Down Transformer double bound type 415/110V AC 300VA Qty : - 1Nos. f) 3 Pole Power Contactor 3 phase 415V AC3 ML-2 with 2NO. + 2 N.C. Aux Coil Voltage 110V AC: - 3 Nos. g) 3 Pole Power Contactor 3 phase 415V AC3 ML-1.5 with 2NO. + 2 N.C.Aux Coil Voltage 110V AC :- 4Nos. h) Pneumatic Time Delay Relay 0-60 Sec Coil Voltage 110 V AC with 1 N.O. + 1 N.C. Qty : - 2 Nos. i) Indicating lamp R, Y, B Qty: - 3 Nos. j) Connector Block of suitable Sizes. 1 Set.

Supply and fixing in replacement of MCCB FP 250 Amp, 35KA,415 Volts with fixed thermal and fixed magnetic setting type complete any retrofit work, terminal links with thimbles, gland complete and taking down of existing MCCBs complete all as specified and as directed.

Supply and fixing in replacement of MCCB FP 200 Amp, 35KA,415 Volts with fixed thermal and fixed magnetic setting type complete any retrofit work, terminal links with thimbles, gland complete and taking down of existing MCCBs complete all as specified and as directed.

Supply and fixing in replacement of MCCB FP 100 Amp, 25KA,415 Volts with fixed thermal and fixed magnetic setting type including powder coated SS enclosure complete, any retrofit work, terminal links with thimbles, gland complete and taking down of existing MCCBs complete all as specified and as directed.

Supply and fixing in replacement of MCB SP , 230 V AC, 6-32 Amp rating 16 KA rupturing capacity, C curve complete with any retrofit work thimbles, gland as per requirement in existing panel complete all as specified and as directed.

Supply and fixing in replacement of MCB 3 pole, 415V AC, 32 Amp rating 16 KA rupturing capacity, C curve complete with any retrofit work thimbles, gland as per requirement in existing panel complete all as specified and as directed.

Supply and fixing in replacement of MCB 3 pole, 415V AC, 63 Amp rating 16 KA rupturing capacity, C curve complete with any retrofit work ,thimbles/lugs, gland as per requirement in existing panel complete all as specified and as directed.

Material and Labour for replacement of steel Wire Rope 8 mm F.M.C Construction 6X36 ungalvanised as per IS 2266/02 alonwith suitable rope clamp complete all as specified and as directed.

Material and Labour for replacement of steel Wire Rope 12 mm F.M.C Construction 6X36 ungalvanised as per IS 2266/02 alonwith suitable rope clamp complete all as specified and as directed.

Material and Labour for replacement of steel Wire Rope 30 mm F.M.C Construction 6X36 ungalvanised as per IS 2266/02 alonwith suitable rope clamp complete all as specified and as directed.

Material and labour for replacement of Bottom Block 1 Ton Capacity 2 fall type totally enclosed hock long shunk forged steel "C" type as IS 3815, hock supporting on thrust bearing and bottom block pulley rest on suitable size ball bearing alongwith safety latch complete all as specified and as directed.

Material and labour for replacement of Bottom Block 5 Ton Capacity 4 fall type totally enclosed hock long shunk forged steel "C" type as IS 3815, hock supporting on thrust bearing and bottom block pulley rest on suitable size ball bearing alongwith safety latch complete all as specified and as directed.

Dismantling and removing of damaged & rusted Copper conductor round bus bar size 6.0 mm dia of EOT Cranes and other connected parts which is installed 20 ft height and more from the ground complete taking down and necessary requirement of scaffolding arrangement laddars,safety belt,and T&P used during the working will be borne by the contractor itself complete all as specified and as directed. Note:- Three wire ( RYB) will be included in the measurement of one running meter.

Universal Switch Gear Control

The new hut furnitures

V r traders

KEWAL SONS

BUSINESS TEK INDIA