A. Construction of bridge connecting Banyan point and Island Garden near central lawn in garden at NBRI, Lucknow. B. Construction and installation of Gate at Nursery Section of Cactus House.

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Disassembling the jointed chimney of dia 200mm to 650mm in to pieces from existing joint between 5.00m to 7.00m length and taking out for repair of damaged parts, tightened through nuts and bolts including cutting the same as and where necessary for one stretch of chimney complete.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: Asbestos sheet.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Execution charges for steel work in built up section in angle, tees, flats and channels including necessary cutting, straightening hosting in position necessary welding etc. complete (labour rate only).

12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand).

Providing Asbestos cement 6 mm thick corrugated sheets roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc.complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required.

Providing and fixing plain A.C. sheet 4.00mm thick facia including fixing with necessary screws/nut-bolt and washer etc. complete.

Cutting and taking out damaged and unshaped irregular part of chimney up to a length of 600mm including correcting in position by replacing through new fabrication with black iron sheet of 14 gauges complete with the help of MS flat 50x5mm flange at both ends including necessary welding complete.

Jointing one part of chimney with second parts through nuts and bolts including necessary gaskets/threads and tightening them to make leak proof through anti gas leakage compound complete.

Grouting of 1 block by 16mm dia. long bolt having hooks and long thread including supply and fixing of 200x200x10mm size MS base plate.

Supply and fixing of 8mm dia. GI wire rope with turned buckle hooks, tinning wire lock including tightening and strengthening through hydra crane complete.

Erection of chimney truly vertical in position through hydra crane including clamping, tightening without any loss of sagging of rope complete (cost of cement concrete block and allied fittings shall be paid in other items separately).

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Credit (buy-back) for damaged and dismantled steel members and the cost will be recovered from the bill of contractor and obtained material will be contractor's property and which has to be disposed off from the site of work.

Note:- Rates should be quoted inclusive of all Taxes, GST etc.

Pranav Kumar

Amiya Enterprises

Moira Interiors Pvt.Ltd.

harpal singh