Addn / Altn and spl repair to security wall near Bldg No P-98 at HQ ANC, Provn of toilet block near JOC coastal security at Comd HQ and certain sanctioned works under GE Haddo, Sri Vijaya Puram

Amount

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

Demolition of precast cement concrete block walling built in CM or cement lime Mortar complete all as specified and as directed

Rough excavation n. exc 1.5m deep and getting out in hard/dense soil complete all as specified and directed

Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in hard/dense soil for foundation, etc or for shafts, wells, cesspits, manholes, pierholes, etc n. exc 10 Sqm on plan and getting out complete all as specified and directed

M&L for returning filling in hard/dense soil including spreading levelling watering and well ramming in layers n. exc 25cm thick complete all as specified and directed

M&L for removing excavated material (any type of soil) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed

M&L for hardcore of broken stone or boulders of gauge n. exc 63 mm deposited spread and levelled in layers n. exc 15 cm thick watered and rammed to a true surface

M&L for 100mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in path finish the top surfaces even and rough to receive top layer complete all as specified and directed

M&L for chequered cement concrete tiles of size 30cm X 30cm X 25mm thick with grey cement and pigments set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor over and including 20mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for chequered cement concrete tiles of size 30cm X 30cm X 25mm thick on vertical surfaces as in skirtings, dados and risers of steps with grey cement and pigments set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor over and including 10mm thick screed bed in CM 1:3 complete all as specified and directed

M&L Cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundations or mass concrete complete all as specified and as directed

M&L for nominal mix RCC 1:1.5:3 type A1 (using 20mm graded crushed stone aggregate) in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L for nominal mix RCC 1:1.5:3 type A1 (using 20mm graded stone aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed

M&L for nominal mix RCC 1:1.5:3 type A1 (using 20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed

M&L formwork for rough finished flat surface to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and directed

M&L formwork for rough finished surface of square, rectangular or triangular surface to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed

M&L formwork for rough finished flat surface to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc also splays between floors and beams, etc complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L precast cement concrete block masonry exc 10 cm width with solid block PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) and setting in cement mortar 1:4 all as specified

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed

M&L for 15mm thick plaster in CM 1:4 on fair face of concrete surface or brick walls finished even and smooth without using extra cement complete all as specified

M&L for preparing newly plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces complete all as specified and directed

M&L for complete removal of existing treatment on plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed

M&L for mild steel work as posts and struts in fencing including cutting tops as required drilling holes, notching for wires etc and similar works conforming to Fe-290 Gde E-165 complete all as specified and as directed

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar works conforming to Fe-290, Gde-E-165 all as specified and as directed

S&F mild steel roof trusses (framed), trrussed, purlins, crane gantries, rails and fastenings and heavy bracket framming (Beam,Tee, Angle, Channels or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and directed

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10cm width or girth not otherwise described complete all as specified and directed

Excavation in post hole in hard/dense soil (or similar holes) each n. exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering, and removing surplus soil to a distance n. exc 50m and making good surface complete all as specified and directed

M&L for cement concrete 1:2:4 type B1 (Using 20mm graded stone agrregate) as in foundation of posts, railing and similar work complete all as specified and directed

Dismantling plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern in roof coverings complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridges, fixed with self tapping screws all as specified and directed

M&L plain anodised aluminium flat section as in wind tie with GI self tapping screws complete all as specifed

S&F Galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire staples or steel pins etc as directed

Excavation in trenches n. exc 1.5m wide and exc 1.5m in depth but n. exc 3m depth in hard/dense soil for foundation, etc or for shafts, wells, cesspits, manholes, pierholes, etc n. exc 10 Sqm on plan and getting out complete all as specified and directed

Surface excavation n. exc 30 cm deep and averaging 15 cm deep in any type of soil and getting out complete all as specified and directed

M&L for nominal mix RCC 1:1.5:3 type A1 (using 20mm graded crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajja/facia and the like complete all as specified and directed

M&L for reinforced precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in landings, drain cover, cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary form work, set in CM 1:4 complete all as specified and directed (Note : Reinforcement shall be measured and paid for separately)

M&L formwork for rough finished flat surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping) complete all as specified and directed

M&L formwork rough finished surface of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work n. exc 10 cm wide complete all as specified and directed

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L precast cement concrete block masonry exc 10 cm width with solid block PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) and setting in cement mortar 1:6 all as specified

M&L for 10mm thick plaster in CM 1:6 on fair face of concrete surface or brick walls finished even and smooth without using extra cement complete all as specified

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth complete all as specified and directed

M&L for 10mm thick plaster in CM 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified

M&L for preparation of newly plastered ceiling surface and applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty complete all as specified and directed

M&L for 25mm thick cement concrete 1:2:4 type B0 (Using 12.5mm graded stone agrregate) as in levelling course, padding etc complete all as specified and directed

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.18 Sqm but n. exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed

M&L for coloured Glazed ceramic tiles in vertical surfaces 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering or bedding layer of cement mortar 1:3 complete all as specified and directed

M&L 14-16mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed

M&L for non glazed ceramic coloured wall cladding tiles 9-10mm thick area of each tiles n. exc 0.18 Sqm as in vertical surface incl cutting the tiles for fixing on curved surfaces set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering or bedding layer of cement mortar 1:3 complete all as per sample kept in the office, specified and directed by Engr-in-Charge

M&L for seamless designed gypsum board false ceiling 12mm thick including for any sunk or raised moulding with 25mm long self drilling/ tapping screws having philips head with joining compound and 48mm wide fiber tape to provide seam less finish and including GI frame work of seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flange of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm suspended from soffit at approx 900mm c/c with GI cleats and steel expansion fasteners with and incl ceiling section ( not exc 1.2m length) of 0.55mm thick having kurled web of 50mm an flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting across the intermediate channel at 457mm c/c incl hangers 6mm dia GI adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete and finally applying two coats of oil bound distember with roller finish over a coat of chalk whiting primer cmplete all as specified and directed

S&F for 2nd class hard wood (SAL) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed

M&L for 35mm thick rubber wood superior quality, chemically pressure treated, egde glued, finger jointed, tongued, grooved as in skelton door shutter complete all as specified and as directed

M&L for 18mm thick designed rubco hut rubber wood frame shutter for cupboard, WHB counter cupboard, wall with finish to match all adjoining surfaces including sanding and applying mixture of filler and NCD thinner (Sheenlac make), pasting chalk putty, applying sealer (Sheenlac make) and wall nut colour stainer and finally applying waxpol (Silicon make) complete all as specified and as directed

M&L for preparation of new/old wooden surfaces and applying melamine polish through the process of snading with wood sanding paper of size 60 & 80 and applying wood filler mixed with NCD thinner including applying wood putty on shabby/ nailing area and sanding with sand paper of size 120 and applying sealer and walnut colour stainer and sanding with sand paper of size 320 and melamine polishing with spray application and again sanding with 400 sand paper and finally applying silicon of make Waxpol with soft fine cloth for better shining and finishing complete all as specified and directed

S&F factory made uPVC white colour sliding window area n. exc 2 Sqm each three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware (Touch lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories (Note : The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose)

Supply only sheet glass, ordinary quality 5.5mm thick in uPVC window/ventilator shutter n. exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 250mm long brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified

S&F 100mm size butt hinges, extruded brass, with mild steel hinge pin, bright polished type B-11 complete all as specified

S&F 200mm size brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified

S&F 150mm size brass handles, cast type, polished bright complete all as specified

S&F floor door stopper of brass body and tongue, anodised, with hard drawn steel spring fixed in floor 140mm overall length of cover plate

S&F 100mm brass 4 levers mortice lock, vertical type complete all as specified

S&F door closer hydraulically regulated aluminium (die cast) body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified

S&F circular/oval LED decorative wall mounted mirror of size ranges 24" to 36" with minimum three types of light (Cool day light, White light, Warm light) complete all as specified and directed by Engr-in-Charge

M&L for 18mm thick HDF boarding (Fire and water proof) as in cup boards/shutters/racks/shelves exterior grade with one side white lamination and other side coloured prelaminated, size of the cabinet as per requirement of the site complete all as specified and as directed by Engr-in-Charge. Make : bajaj/ Axis/Greenply/ Amnchidply or equivalent. Note : (i) Cutting edges of cupboard shutter/ shelves to be finished with adhesive edge binding tape all as directed

S&F stainless steel non megnetic barrel tower bolt 150mm long of extruded section complete all as specified. Make : Hettich/Harrison/Dorsel

S&F stainless steel non megnetic bow handle "D" type anodized 150mm long complete all as specified. Make : Hettich/Harrison/Godrej

S&F telescopic ball bearing runners minimum length 400mm (KA 5632) full extension load capacity 45 Kg complete all as specified. Make : Godrej/Hettich/Kaff

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete all as specified. Make : Hettich/Kaff/Godrej/Kich

S&F stainless steel auto closing hinges 35mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified. Make : Hettich/Harrison/Godrej

S&F curtain rods 25mm dia, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified

S&F double layer rotational moulded PVC water storage tank cylinderical, vertical with closed top hoisted and fixed in position tank capacity 1000 Ltr with and including PTMT float valve 20mm dia and making connection for inlet and outlet complete all as specified and directed

S&F 20mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including suitable reducer for 15mm dia taps fitting as required complete all as specified

Cutting chases in stone, concrete block or slab walls, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth

S&F 25mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including suitable reducer for 15mm dia taps fitting as required complete all as specified

S&F 25mm bore gun matel globe or gate valve with iron wheel, screwed both ends for iron pipes complete all as specified

S&F PVC (SWR) pipe 110mm bore, single socketed, in any length including bends, socket etc with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed

S&F PVC (SWR) pipe 110mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed

S&F PVC (SWR) 110mm dia bend of any radius and jointed with approved adhesive complete all as specified and directed

S&F PVC (SWR) vent cowl 110mm dia jointed with approved adhesive complete all as specified and directed

S&F PVC (SWR) pipe 75mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed

S&F PVC (SWR) bend 75mm dia, any radius as required and jointed with approved adhesive complete all as specified and directed

S&F 75mm outlet dia PVC (SWR) floor trap with grating including jointing with solvent cement to waste pipe complete all as directed

S&F vitreous china wash down tankless single piece water closed pan (Pedestal pattern) of size 360x590x450mm including 'S' trap 300mm with UF soft close slim seat cover, hinges, single flush with sensor and manual operated including all fixing accessories complete all as specified Make : Jaquar Cat Part No ARS-WHT-39851S300UFSMTL or equivalent in Parryware/Hindware/Prayag

S&F vitreous china counter top wash hand basin rectangular shape of size 495x395x150mm including 32 mm CP waste coupling, waste fittings all necessary inlet and out let connections complete all as specified Make : Jaquar Cat Part No JDS-WHT-25909 or equivalent in Parryware/Hindware/Prayag

S&F sensor faucet for wash hand basin (battery operated), 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, with long swan neck, screwed both ends for iron pipe or for unions complete all as specified Make : Jaquar Cat Part No SNR-CHR-51011N or equivalent in Parryware/Hindware/Prayag

S&F Vitreous China urinals, half stall type complete including waste coupling, waste pipe, providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed Make : Jaquar Cat Part No URS-WHT-13263 or equivalent in Parryware/Hindware/Prayag

S&F sensor flushing valve for urinal with complete fittings (battery operated) suitable for urinal URS-WHT-13263 complete all as specified and directed Make : Jaquar Cat Part No SNR-CHR-51097 or equivalent in Parryware/Hindware/Prayag

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed Makte : Jaguar Cat Part No ALD-573 or equivalent in Parryware/Hindware/Prayag

S&F in repair two way bib cock, 15mm dia cast copper alloy chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified

S&F in repair angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for unions complete all as specified and as directed Make : Jaquar Cat part No CON-053KN or equivalent in Prayag/ Parryware

S&F tubular towel rail, brass, chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs complete all as specified and as directed Make : Jaquar Cat part No AQN-7711 or equivalent in Prayag / Parryware.

S&F Toilet paper holder Make : Jaquar Code ACN-1153N or equivalent model in Parryware/Prayag/Gem

S&F stainless steel hanger of size 450x3.5x1mm thick having minimum 6 pegs suitable for hanging cloths and fixed with minimum 2 Nos stainless screws complete all as specified complete all as specified

S&F CP corner glass shelf with bracket complete all as specified. Make : Jaguar Cat Part No - CAN-1173 or equivalent in saint Gobain / Modi.

S&F chromium plated soap dish of size 120x80mm, fixed to plugs with chromium plated brass screws complete all as specified

S&F PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer complete all as specified

M&L for 40mm thick PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in path finish the top surfaces even and smooth complete all as specified and directed

Supply only river sand complete all as specified and directed

Supply only water proofing compound complete all as specified and directed

M&L for light shade vitrified ceramic tiles minimum 8mm thick (square/ rectangular) polished area of each tiles n. exc 0.36 Sqm (600x600mm) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed

M&L for light shade vitrified ceramic tiles minimum 8mm thick (square/ rectangular) polished area of each tiles n. exc 0.36 Sqm (600x600mm) in vertical surfaces such as skirting, dados and riser etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed of cement mortar 1:3 complete all as specified and directed

S&F for stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc of required size on the top of floor or the side of waist slab with suitable arrangement complete all as specified

S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staples all as specified and directed

M&L for removing excavated material (any type of soil) to a distance exc 100m but n. exc 200m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

M&L for 100mm thick PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in hardstanding/path laid in panels, finish the top surfaces even and fair complete including filling the joints with mastic compound all as specified and directed

M&L for Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified

M&L for 15mm thick plaster in CM 1:4 including liquid water proofing compound @ 200ml per 50 Kg cement bag on fair face of brick walls or concrete surface, finished the surface even and smooth without using extra cement complete all as specified (Note : WPC shall be measured and paid seperately)

M & L point wiring complete with 1100 volts grade, 1.5 sq.mm (nominal area), single core, FRLS PVC insulated ,unsheathed, multi stranded copper conductor cable drawn through and including medium grade, rigid , non-metallic PVC concealed/ on surface conduit of size not less than 20 mm dia, with all necessary fittings, concealed in walls/ floor or surface on wall/ roof duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth duly including suitable size of factory made fabricated MS sheet modular terminal box, flush mounting in the wall for mounting switches/switch socket combinations/ fan regulators etc., covered with suitable size of modular cover plates complete in making good the existing surface with existing colour coding as required at site complete all as specified for the following :-

Description same as per item Sl No 115 above but for One light/fan point controlled by one modular switch 5 Amps one way complete all as specified and directed.

Description same as per item Sl No 115 above but for one modular 3 pin 6 Amp socket out let on independent board complete all as specified and directed.

Description same as per item Sl No 115 above but for one modular 3 pin 6 Amps switch socket on same Board complete all as specified and directed.

S & F for switch modular type, 6 Amps 1 module, 230 volts AC circuit complete all as specified and directed.

S&F for socket outlet modular type 1 way 6 Amps,3 pin, flush type 230 volts AC circuit complete all as specified and directed.

S&F for ceiling rose, 3 phase, PVC polycarbonate, isolated body complete all as specified and directed.

S&F of decorative ultra slim linear LED lighting fixture of 15 watt recess mounted 220V , 50 Hz with aluminium housing , environmental frendly energy efficient fitting recess mounted round/ spare in shape (Warm white/ white colour as per requirement of site complete) complete all as specified and directed. Make : Philips Cat Part No. Dura slim or equivalent make in CG/Havells/Luker. Note : The rate quoted deemed to include for any alterations required to existing false ceiling as per site condition for fixing light fitting.

S&F air ventilating fan 200 mm sweep single ph, 230 volt PVC body with louvers incl all fixing arrangement complete all as specified and directed. Make : Havellls, Model No. FHVVEDXOWH08 Ventil Air DX or CG Model No. BRISK AIR NEO or equivalent to orient/ Usha/ Khaitan.

M&L for aluminium composite panel sheet of 3 mm thick with skin thickness of 0.25 of aluminium on both sides, sandwiched by 2.5 polyethylene core with PVDF coating of 30.0 micron, cut to shape as required (for ducting of any shape) and fixed with the air ventilation fan on window / wall all as specified and directed by Engr-in-Charge.

M&L cutting channels, grooves or rebates n. exc 15cm girth, and trimming surface with or without reinforcement all as specified and directed by Engr-in-Charge.

LOOK UP ENTERPRISES (BID ID -3279026)

JD Construction (BID ID -3278811)

NAWAZ CONSTRUCTIONS (BID ID -3277560)

CARTWHEEL CONSTRUCTION (BID ID -3278739)

SKV Engineering (BID ID -3279410)

Sree Tirumala Enterprises (BID ID -3278101)

Sri Ram Construction (BID ID -3279535)

M/S VISHAL CONSTRUCTION (BID ID -3279856)