Extension of kendriya Bhandar at 1st floor level at IIPA, New Delhi

BILL OF QUANTITIES (BOQ)

S.No. Sub-Head DSR Amount (in Rs.) NDSR Amount (in Rs.)

2 ELECTRICAL WORKS 2,69,763.00 89,173.40

3 PLUMBING WORKS 1,33,989.15 27,411.23

GRAND TOTAL 55,88,269.00

GRAND TOTAL 55,88,269.00

Digitally signed by AMIT

EXTENSION OF KENDRIYA BHANDAR AT IIPA (1ST FLOOR) , NEW DELHI

SUMMARY OF CIVIL & INTERIOR WORKS

A DISMANTALLING 2,26,433.55 0.00

B EARTH WORKS, PCC & RCC WORKS 20,53,369.45 0.00

C FLOORING, MASONRY & WET WORKS 16,02,074.60 86,478.56

D DOORS & WINDOWS 92,943.36 4,76,301.18

E FINISHES & MISCELLANEOUS 4,75,331.90 55,000.00

EXTENSION OF KENDRIYA BHANDAR AT IIPA (1ST FLOOR) , NEW DELHI

SR. NO. DESCRIPTION UNIT QTY DSR RATE DSR AMOUNT NDSR RATE NDSR AMOUNT

Demolishing brick tile covering in terracing including stacking of

1 15.26 serviceable material and disposal of unserviceable material within SQM 185.00 105.35 19,489.75

50 metres lead.

Demolishing mud phaska in terracing and disposal of material

within 50 metres lead

Demolishing brick work manually / by mechanical means including

stacking of serviceable material and disposal of unserviceable

material within 50 metres lead as per direction of Engineer-in-

Demolishing cement concrete manually / by mechanical means

4 15.2 including disposal of material within 50 metres lead as per direction

of Engineer-in - charge.

15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) CUM 5.00 2,434.25 12,171.25

Demolishing R.C.C. work manually / by mechanical means

including stacking of steel bars and disposal of unserviceable

material within 50 metres lead as per direction of Engineer-in-

Disposal of building rubbish / malba / similar unserviceable,

dismantled or waste materials by mechanical means, including

6 15.60 loading, transporting, unloading to approved municipal dumping CUM 110.00 263.95 29,034.50

ground or as approved by Engineer-in-charge, beyond 50 m initial

lead, for all leads including all lifts involved.

TOTAL OF DISMANTALLING 2,26,433.55 0.00

Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means in foundation trenches or drains (not

exceeding 1.5 m in width or 10 sqm on plan), including dressing of

sides and ramming of bottoms, lift upto 1.5 m, including getting out

the excavated soil and disposal of surplus excavated soil as

directed, within a lead of 50 m.

2.8.1 All kinds of soil

Digitally signed by AMIT

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in

depth, consolidating each deposited layer by ramming and

watering, lead up to 50 and for all lift.

PLAIN CEMENT CONCRETE(1:4:8) WITHOUT FLY ASH

Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work up

to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural

4.1.8 sources : 8 graded stone aggregate 40 mm nominal size CUM 7.00 6,812.00 47,684.00

derived from natural sources)

Providing and laying in position ready mixed or site batched design

mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural

sources, Portland Pozzolana / Ordinary Portland /Portland Slag

cement, admixtures in recommended proportions as per IS: 9103 to

accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but

excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge, for the

following grades of concrete.:

Note: Extra cement up to 10% of the minimum specified cement

content in design mix shall be payable separately. In case the

cement content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement.

5.33.1 All works upto plinth level

Concrete of M30 grade with minimum cement content of 350 kg

5.33.2 All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg

Concrete of M30 grade with minimum cement content of 350 kg

Centering and shuttering including strutting, propping etc. and

removal of form for

5.1 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete SQM 20.00 392.15 7,843.00

5.2 5.9.3 Suspended floors, roofs, landings, balconies and access platform SQM 220.00 927.25 2,03,995.00

5.3 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers SQM 99.00 736.60 72,923.40

5.4 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts SQM 65.00 961.30 62,484.50

Digitally signed by AMIT

5.5 5.9.7 Stairs, (excluding landings) except spiral-staircases SQM 15.00 764.95 11,474.25

Steel reinforcement for R.C.C. work including straightening, cutting,

6 5.22 bending, placing in position and binding all complete upto plinth

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. KG 1,201 107.85 1,29,491.00

Steel reinforcement for R.C.C. work including straightening, cutting,

7 5.22A bending, placing in position and binding all complete above plinth

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. KG 7,200.00 107.85 7,76,520.00

TOTAL OF EARTH WORKS, PCC & RCC WORKS 20,53,369.45 0.00

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate) finished with a floating coat of neat

cement, including cement slurry, but excluding the cost of nosing of

steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 345.00 614.20 2,11,899.00

Providing and applying fibre reinforced elastomeric liquid water

proofing membrane with resilient acrylic polymers having Sun

Reflectivity Index (SRI) of 105 on top of concrete roof in three coats

@10.76 litre/ 10 sqm. One coat of self-priming of elastomeric

waterproofing liquid (dilution with water in the ratio of 3:1) and two

2 22.22A coats of undiluted elastomeric waterproofing liquid (dry film SQM 30.00 536.10 16,083.00

thickness of complete application/system not less than 500

microns). The operation shall be carried out after scrapping and

properly cleaning the surface to remove loose particles with wire

brushes, complete in all respect as per the direction of Engineer-in-

Providing and applying fibre reinforced elastomeric liquid water

proofing membrane with resilient acrylic polymers having Sun

Reflectivity Index (SRI) of 105 on top of concrete roof in three coats

@10.76 litre/ 10 sqm. One coat of self-priming of elastomeric

waterproofing liquid (dilution with water in the ratio of 3:1) and two

3 coats of undiluted elastomeric waterproofing liquid (dry film SQM 185.00 531.10 98,253.50

thickness of complete application/system not less than 500

microns). The operation shall be carried out after scrapping and

properly cleaning the surface to remove loose particles with wire

brushes, complete in all respect as per the direction of Engineerin-

Digitally signed by AMIT

Providing and laying Vitrified tiles in floor in different sizes (thickness

to be specified by the manufacturer) with water absorption less

than 0.08% and conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid on 20 mm thick cement

mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement

slurry @3.3 kg/sqm including grouting the joints with white cement

and matching pigments etc. The tiles must be cut with the zero

chipping diamond cutter only . Laying of tiles will be done with the

notch trowel, plier, wedge, clips of required thickness, leveling

system and rubber mallet for placing the tiles gently and easily.

11.41A.2 Glazed vitrified floor tiles polished finish of size

Same as above but for skirting and silimar locations upto100mm

Providing and laying rectified Glazed Ceramic floor tiles of size

300x300 mm or more (thickness to be specified by the

manufacturer), of 1st quality conforming to IS : 15622, of approved

make, in all colours, shades, except White, Ivory, Grey, Fume Red

Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse

sand), jointing with grey cement slurry @ 3.3 kg/ sqm including

pointing the joints with white cement and matching pigments etc.,

Grouting the joints of flooring tiles having joints of upto 5 mm width,

using epoxy grout mix of 0.70 kg of organic coated filler of desired

7 MR shade (0.10 kg of hardener and 0.20 kg of resin per kg), including

filling / grouting and finishing complete as per direction of Engineer-

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x

20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70

and initial emittance > 0.75 on waterproof and sloped surface of

terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4

8 12.55 (1 cement : 4 coarse sand) and grouting the joints with mix of white SQM 185.00 1,703.95 3,15,230.75

cement & marble powder in ratio of 1:1, including rubbing and

polishing of the surface upto 3 cuts complete, including providing

skirting upto 150 mm height along the parapet walls in the same

Digitally signed by AMIT

Providing and laying flamed finish Granite stone flooring in required

design and patterns, in linear as well as curvilinear portions of the

building all complete as per the architectural drawings with 18 mm

thick stone slab over 20 mm (average) thick base of cement mortar

1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry

and pointing with white cement slurry admixed with pigment of

matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown,

Cat Eye or equivalent.

Brick work with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in foundation and plinth in:

6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) CUM 55.00 7,370.65 4,05,385.75

Half brick masonry with common burnt clay F.P.S. (non modular)

11 6.13 bricks of class designation 7.5 in superstructure above plinth level up

to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) SQM 30.00 1,123.80 33,714.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars

at every third course of half brick masonry.

13 13.1 12 mm cement plaster of mix :

14 13.4 12 mm cement plaster of mix :

POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm

15 MR - 02 to 15mm thick POP Punning over cement plaster in line & plumb SQM 135.00 299.79 40,471.24

finished smooth to receive paint. (Internal surfaces of walls).

TOTAL OF FLOORING, MASONRY & WET WORKS 16,02,074.60 86,478.56

Digitally signed by AMIT

Providing and fixing factory made single extruded WPC (Wood

Polymer Composite) solid door/window/Clerestory windows & other

Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-

60 (Suspension Grade), calcium carbonate and natural fibers

(wood powder/ rice husk/ wheat husk) and non toxic additives

(maximum toxicity index of 12 for 100 gms) fabricated with miter

joints after applying PVC solvent cement and screwed with full

body threaded star headed SS screws having minimum frame

density of 750 kg/cum, screw withdrawal strength of 2200 N (Face)

& 1100 N (Edge), minimum compressive strength of 58 N/mm2,

modulus of elasticity 900 N/mm2 and resistance to spread of flame

of Class A category with property of being termite/borer proof,

water/moisture proof and fire retardant and fixed in position with

M.S hold fast/lugs/SS dash fasteners of required dia and length

complete as per direction of Engineer-In- Charge. (M.S hold

fast/lugs or SS dash fasteners shall be paid for separately).

Note: For WPC solid door/window frames, minus 5 mm tolerance in

dimensions i.e depth and width of profile shall be acceptable.

Variation in profile dimensions on plus side shall be acceptable but

no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood

Polymer Composite) solid plain flush door shutter of required size

comprising of virgin polymer of K value 58-60 (Suspension Grade),

calcium carbonate and natural fibers (wood powder/ rice

husk/wheat husk) and non toxic additives (maximum toxicity index

of 12 for 100 gms) having minimum density of 650 kg/cum and

screw withdrawal strength of 1800 N (Face) & 900 N (Edge),

minimum compressive strength 50 N/mm2, modulus of elasticity 850

N/mm2 and resistance to spread of flame of Class A category with

property of being termite/borer proof, water/moisture proof and fire

retardant and fixing with stainless steel butt hinges of required size

with necessary full body threaded star headed counter sunk S.S

screws, all as per direction of Engineer-In- Charge. (Note: stainless

steel butt hinges and necessary S.S screws shall be paid separately)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to

frame with 10 mm diameter bolts, nuts and wooden plugs and

3 9.53 embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 EACH 24.00 228.85 5,492.40

cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal

Digitally signed by AMIT

STILE DOOR - Providing & Fixing of Stile Door System having size of

75*45 with Door Frame formed out of 45* 40mm / 50*50mm of 6063-

T6 Virgin grade duly Anodized Aluminium, including 10 mm

Toughened Glass. The cost to include hardware like Door Closure,

4nos Hinges, Lever Handle with mortice lock, Door Seal & Gaskets

etc. in approved shade and design as per architectural drawings

and instructions of the architect. The size of door shall be upto

UPVC Windows : Supply and Fixing of Tripple Track/ Tripple Channel

UPVC Windows, DGU/ Sandvich Glasses (6 mm Reflective Glass + 10

5 MR - 04 mm Air Gap + 6 mm Plain Toughned Glass) on two tracks and SS SQM 26.74 13,720.00 3,66,840.00

Mesh on One Track, complete as per the requirement of engineer

MORTICE LOCK AND LEVER HANDLES- Providing and installing

6 MR - 05 Tubular Handle in SS packaged with Mortice lockset 55mm backset, NOS 4.00 5,140.00 20,560.00

20 SS forend, SS strike plate and EP Cylinder for all flush doors.

TOTAL OF DOORS & WINDOWS 92,943.36 4,76,301.18

Applying priming coats with primer of approved brand and

1 13.85 manufacture, having low VOC (Volatile Organic Compound)

With water thinnable cement primer on wall surface having VOC

content less than 50 grams/litre

Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50

2 13.83 grams/ litre. of approved brand and manufacture, including

applying additional coats wherever required to achieve even

shade and colour.

3 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade:

New work (Two or more coat applied @ 1.67 ltr/10 sqm over

13.46.1 and including priming coat of exterior primer applied @ 0.90 SQM 300.00 160.60 48,180.00

Digitally signed by AMIT

Providing and fixing double scaffolding system (cup lock type) on

the exterior side of building/structure, upto 25 metre height, above

ground level, including additional rows of scaffolding in stepped

manner as per requirement of site, made with 40mm dia M.S. tube,

placed 1.5 metre centre to centre, horizontal & vertical tubes joint

with cup & lock system with M.S. Tubes, M.S. tube challis, M.S.

clamps and staircase system in the scaffolding for working platform

etc. and maintaining it in a serviceable condition for execution of

4 24.2 work of cleaning and/ or pointing and/ or applying chemical and sqm 100.00 338.25 33,825.00

removing it thereafter. The scaffolding system shall be stiffened with

bracings, runners, connecting with the building etc, wherever

required, if feasible, for inspection of work at required locations with

essential safety features for the workmen etc., complete as per

directions and approval of Engineer-in-charge. Note:- (1) The

elevational area of the scaffolding shall be measured for payment

purpose. (2) The payment will be made once only for execution of

all items for such works.

Preparation of complete set of arhchiteural drawings including

5 MR architecutral details. A qualified professional for the purpose shall Nos 1.00 55,000.00 55,000.00

be appointed after due appproval from Engineer In Charge.

Steel work welded in built up sections/ framed work, including

6 10.25 cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and

Providing and fixing hand rail of approved size by welding etc. to

7 10.26 steel ladder railing, balcony railing, staircase railing and similar

works, including applying priming coat of approved steel primer.

Supplying and fixing rolling shutters of approved make, made of

required size M.S. laths, interlocked together through their entire

length and jointed together at the end by end locks, mounted on

specially designed pipe shaft with brackets, side guides and

8 10.6 arrangements for inside and outside locking with push and pull

operation complete, including the cost of providing and fixing

necessary 27.5 cm long wire springs manufactured from high tensile

steel wire of adequate strength conforming to IS: 4454 - part 1 and

M.S. top cover of required thickness for rolling shutters.

10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover SQM 25.00 3,653.20 91,330.00

9 10.7 Providing and fixing ball bearing for rolling shutters. EACH 4.00 492.35 1,969.40

Digitally signed by AMIT

Extra for providing mechanical device chain and crank operation

for operating rolling shutters.

Exceeding 10.00 sqm and upto 16.80 sqm in the area SQM 25.00 1,281.35 32,033.75

Extra for providing grilled rolling shutters manufactured out of 8 mm

11 10.9 dia M.S. bar instead of laths as per design approved by Engineer-in- SQM 10.00 786.25 7,862.50

charge, (area of grill to be measured).

Finishing with Epoxy paint (two or more coats) at all locations

prepared and applied as per manufacturer’s specifications

including appropriate priming coat, preparation of surface, etc.

TOTAL OF FINISHES & MISCELLANEOUS 4,75,331.90 55,000.00

Digitally signed by AMIT

EXTENSION OF KENDRIYA BHANDAR AT IIPA (1ST FLOOR) , NEW DELHI

SUB HEAD NDSR AMOUNT (Rs.) DSR AMOUNT (Rs.)

1 CABLES AND DISTRIBUTION BOARDS Rs. 85,569.69 Rs. 99,787.00

2 CIRCUIT POINT WIRING Rs. - Rs. 1,32,240.00

3 LIGHTING FIXTURES & FANS Rs. 3,603.71 Rs. 37,736.00

GRAND TOTAL Rs. 3,58,936.40

GRAND TOTAL Rs. 3,58,936.40

EXTENSION OF KENDRIYA BHANDAR AT IIPA (1ST FLOOR) , NEW DELHI

SR. NO. DSR REF. NO. DESCRIPTION UNIT QUANTITY RATE MR AMOUNT DSR AMOUNT

A CABLES AND DISTRIBUTION BOARDS

Supply, testing and commissioning of following sizes of 1.1 KV grade XLPE insulated FRLS

Aluminium /Copper conductor cables laid over MS supports cable racks or fixing on walls

including clamping the cable to supports in an approved manner as required complete with

Copper earthing as specified for continuous earthing along with cable . (Earthing will be

measured separately and need not be quoted under this item). All complete as required and

as per final instruction as given by engineer-in-charge and as per Technical specifications.

3.5 Core x 50 sq.mm., XLPE Insulated Aluminium Conductor Armoured Cable Mtr. 100.00 671.10 67,109.69

Supply of following sizes Copper conductor armoured PVC insulated PVC sheathed XLPE cable

2 MR - 02 of grade 1.1 KV in the existing open masonary duct/ surface/ cable tray/ pipe etc complete

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1

KV grade of following size on wall surface as required.

10.7.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) Mtr. 110.00 151.00 16,610.00

Supplying and making end termination with brass compression gland and Copper lugs

3 MR - 03 for following size of PVC insulated and PVC sheathed / XLPE Copper conductor cable of

1.1 KV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for

4 11.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV

grade as required.

Supplying Installation, Testing and Commissioning of following capacity TPN tap off box made

5 3.2 of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains

complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB

distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned

6 2.5 copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs

and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase

outlets are required.)

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual

7 2.15 current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Digitally signed by AMIT

EXTENSION OF KENDRIYA BHANDAR AT IIPA (1ST FLOOR) , NEW DELHI

SR. NO. DSR REF. NO. DESCRIPTION UNIT QUANTITY RATE MR AMOUNT DSR AMOUNT

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker

9 2.10 suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing Single Pole Blanking Plate in the existing MCB DB complete Etc. as

A TOTAL OF CABLES AND DISTRIBUTION BOARDS (CARRIED OVER TO SUMMARY) 85,569.69 99,787.00

B CIRCUIT POINT WIRING

Point wiring for light point /Fan/Exhaust Fan point/ call bell point using 2 runs of 1100 V grade

1.5 sqmm & one run of 1.5 sq.mm FRLS insulated multistranded copper wires, in & including

1 25 mm dia , MS conduit surface/ concealed in wall / ceiling conferming to IS 732 including all

accessries such as junction boxes , conduit bends, elbows and ceiling rose , and anodised GI

switch box with modular switch ,modular plate and the box covered with front plate

a 1.3.3 One light point controlled by one 6A switch Per Pts 10.00 1,845.00 18,450.00

b 1.54.3 Secondary light point controlled by same switch Per Pts 20.00 1,094.00 21,880.00

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

a 1.7.1 2x1.5sqmm+1x1.5sqmmearth wire 100.00 327.00 32,700.00

3 1.3.3 Exhaust fan point including of ceiling rose near fan. Per Pts 2.00 1,845.00 3,690.00

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

4 1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC

conduit as required.

Supply and fixing of following sizes of MS conduit along with accessories in surface /recess

5 1.20 including painting in case of surface conduit,or cutting the wall and making good the same in

case of recessed conduit as required

TOTAL OF CIRCUIT POINT WIRING (CARRIED OVER TO SUMMARY) 0.00 1,32,240.00

Digitally signed by AMIT

EXTENSION OF KENDRIYA BHANDAR AT IIPA (1ST FLOOR) , NEW DELHI

SR. NO. DSR REF. NO. DESCRIPTION UNIT QUANTITY RATE MR AMOUNT DSR AMOUNT

Digitally signed by AMIT

EXTENSION OF KENDRIYA BHANDAR AT IIPA (1ST FLOOR) , NEW DELHI

SR. NO. DSR REF. NO. DESCRIPTION UNIT QUANTITY RATE MR AMOUNT DSR AMOUNT

C LIGHTING FIXTURES & FANS

1 8.9 LED Batten light (System lumen efficacy ≥105 <120 lm/Watt)

Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of

following body material and construction as per IS : 10322 with driver (Replaceable) as per the

requirement with Driver efficiency >85% ,Operating voltage AC 140-270 Volt, freq 50/60 hz,

Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with

Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should

be below 5 %), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours

with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K

(As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power

consumption should not more than the specified rating and Fixture shall be of relevant BIS

standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm

FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 &

LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be

submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per

requirement. (Thermal management: heat sink of aluminum housing such that LED junction

temperature shall not rise above 90°C).

Powder coated die cast / Extruded aluminium Body (Thickness

2 8.3 LED Down lighter (SMD Type) (System lumen efficacy >135lm/Watt)

Supplying, Installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round

/square/Rectangular) SMD type of following body material with PMMA and prismatic diffuser

and construction as per IS : 10322 with driver as per the requirement with Driver efficiency

>85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range - 5 0C to

40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P.

F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %),

life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of

initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT

3000°K/ 4000°K /5700°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching)

<3, Maximum power consumption should not more than the specified rating and Fixture shall

be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen

printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR,

PVC insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output. LM79 & LM80 Test

report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT

shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat

sink of aluminium housing such that LED junction temperature shall not rise above 90°C).

Powder coated die cast /Extruded aluminium Body including trim .

Digitally signed by AMIT

EXTENSION OF KENDRIYA BHANDAR AT IIPA (1ST FLOOR) , NEW DELHI

SR. NO. DSR REF. NO. DESCRIPTION UNIT QUANTITY RATE MR AMOUNT DSR AMOUNT

Providing & Fixing Heavy Duty 4 Blade, 15" Exhuast Fan complete with all hardware and

connectors etc., as per the direction of the engineer In charge

9.1 Brush Less Direct Current (BLDC) Fan with Remote

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current

(BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod,

2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body. Power Factor not less

than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019),

THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed

control and all remaining accessories including safety pin, nut bolts, washers, temperature

rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single

phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5

sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as

9.1.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) Each 4.00 2,882.00 11,528.00

TOTAL OF LIGHTING FIXTURES & FANS (CARRIED OVER TO SUMMARY) 3,603.71 37,736.00

Digitally signed by AMIT

EXTENSION OF KENDRIYA BHANDAR AT IIPA (1ST FLOOR) , NEW DELHI

SUMMARY OF WORKS

Sr. No. Item DSR Amount NDSR Amount

A SANITARY FIXTURES 43,499.10 27,411.23

B INTERNAL DRAINAGE 52,463.00

C WATER SUPPLY 38,027.05

SR. NO. DSR REF. NO. ITEM UNIT QUANTITY DSR RATE DSR AMOUNT NSDR RATE NDSR AMOUNT

A SANITARY FIXTURES

Providing and fixing white vitreous china extended wall

mounting water closet of size 780x370x690 mm of

approved shape including providing & fixing white

1 17.78 vitreous china cistern with dual flush fitting, of flushing Each 2.00 14,999.15 29,998.30

capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres),

including seat cover, and cistern fittings, nuts, bolts and

gasket etc complete.

Supply, installation, testing and commissioning of

glazed vitreous china under counter wash basin with

R.S. or C.I. brackets painted white, 32mm C.P. brass

2 MR - 01 waste of standard pattern , C.P brass wall flange 32 Each 2.00 11,952.68 23,905.36

mm dia. C.P. brass bottle trap and union 32 mm dia

C.P. pipes to wall flange. complete including cutting

and making good the walls wherever required.

Digitally signed by AMIT

Providing and fixing white vitreous china battery based

infrared sensor operated urinal of approx. size 610 x 390

x 370 mm having pre & post flushing with water (250 ml

3 17.80 & 500 ml consumption), having water inlet from back Each 1.00 7,979.20 7,979.20

side, including fixing to wall with suitable brackets all as

per manufacturers specification and direction of

Engineer-in-charge.

4 17.34 Providing and fixing toilet paper holder :

Providing and fixing 600x450 mm beveled edge mirror

of superior glass (of approved quality) complete with 6

mm thick hard board ground fixed to wooden cleats

with C.P. brass screws and washers complete.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible

tube upto 1 metre long with S.S. triangular plate to

Eureopean type W.C. of quality and make as

approved by Engineer - in - charge.

Providing & fixing 15 mm dia C.P. brass bib cock with

C.P. wall flange of approved quality.

Detail of Sanitary fixture are for the information of the

Contractor,however model/makes of all sanitary

fixtures shall be selected by Architect/Interior

designer/Project manager and the same shall be

binding for execution.

No additional fixing cost shall be paid for change in

type of sanitary fixtures.

Contractor to receive all the above mentioned items &

store at place as directed at site.

B INTERNAL DRAINAGE

Providing & fixing PTMT grating of approved quality

18.58.1 Circular type

Digitally signed by AMIT

17.35 Providing and fixing soil, waste and vent pipes :

17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 metre 10.00 1,151.90 11,519.00

17.35.2 75 mm diameter :

17.35.2.1 Sand cast iron S&S pipe as per IS: 1729 metre 10.00 1,044.75 10,447.50

Providing and fixing M.S. holder-bat clamps of

approved design to Sand Cast iron/cast iron (spun)

pipe embedded in and including cement concrete

17.37 blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm nominal size),

including cost of cutting holes and making good the

Providing and fixing bend of required degree with

17.38 access door, insertion rubber washer 3 mm thick, bolts

and nuts complete.

17.38.1.1 Sand cast iron S&S as per IS - 1729 each 2.00 598.50 1,197.00

17.38.2.1 Sand cast iron S&S as per IS - 1729 each 2.00 501.45 1,002.90

Providing and fixing plain bend of required degree.

17.39.1.1 Sand cast iron S&S as per IS - 1729 each 2.00 470.45 940.90

17.39.2.1 Sand cast iron S&S as per IS - 1729 each 2.00 376.25 752.50

Providing lead caulked joints to sand cast

17.58 iron/centrifugally cast (spun) iron pipes and fittings of

Painting sand cast iron/ centrifugally cast (spun) iron

soil, waste vent pipes and fittings with two coats of

17.65 synthetic enamel paint of any colour such as

chocolate grey, or buff etc. over a coat of primer (of

approved quality) for new work :

17.65.1 100 mm diameter pipe metre 10.00 82.80 828.00

Digitally signed by AMIT

17.65.2 75 mm diameter pipe metre 10.00 62.95 629.50

Making khurras 45x45 cm with average minimum

thickness of 5 cm cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate of 20 mm

nominal size) over P.V.C. sheet 1 m x1 m x 400 micron,

finished with 12 mm cement plaster 1:3 (1 cement : 3

coarse sand) and a coat of neat cement, rounding the

edges and making and finishing the outlet complete.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs

for passing drain pipe etc. and repairing the hole after

insertion of drain pipe etc. with cement concrete 1:2:4

18.77 (1 cement : 2 coarse sand : 4 graded stone aggregate Each 4.00 452.00 1,808.00

20 mm nominal size), including finishing complete so as

to make it leak proof.

Providing and fixing on wall face unplasticised Rigid

PVC rain water pipes conforming to IS : 13592 Type A,

12.41 including jointing with seal ring conforming to IS : 5382,

leaving 10 mm gap for thermal expansion, (i) Single

socketed pipes.

Providing and fixing to the inlet mouth of rain water

pipe cast iron grating

15 cm diameter and weighing not less than 440 grams.

SUB TOTAL 52,463.00

C WATER SUPPLY

Providing and fixing Chlorinate Polyvinyl Chloride

(CPVC) pipes having thermal stability for hot & cold

water supply including all CPVC plain & brass

threaded fittings i/c fixing the pipe with clamps at 1.00

18.8 m spacing. This including jointing of pipes & fittings with

one step CPVC solvent cement and the cost of cutting

chases and making good the the same including

testing of joints complete as per direction of engineer

Digitally signed by AMIT

Concealed work including cutting chases and making

good the walls etc.

18.8.1 15 mm nominal outer dia Pipes RM 10.00 497.80 4,978.00

18.8.2 20 mm nominal outer dia Pipes RM 10.00 537.60 5,376.00

18.8.3 25 mm nominal outer dia Pipes RM 20.00 627.25 12,545.00

Providing and fixing G.I. pipes complete with G.I.

18.10 fittings and clamps, i/c cutting and making good the

18.10.1 15 mm dia nominal bore RM 10.00 366.40 3,664.00

Providing & fixing ball valve ( brass) of approved

18.18 quality,High or low pressure, with plastic floats

Providing and placing on terrace (at all floor levels)

polyethylene water storage tank, IS : 12701 marked,

18.48 with cover and suitable locking arrangement and Per Litre 1,000.00 11.00 11,000.00

making necessary holes for inlet, outlet and overflow

pipes but without fittings and the base support for tank.

SUB TOTAL 38,027.05

Digitally signed by AMIT