CONSTRUCTION OF LPG CREMATORIUM IN Kattangaluthur

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

For Foundation

For Plinth Beam

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials)

Below Ground Level

Above Ground Level

Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Brick work in CM 1:5 (one cement & five sand) using Third Class Country Brick Kiln Burnt of size 8"X41/4"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Below Basement

Above Basement

Plastering with cement mortar (1:3) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications

Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Brick lining for 300mm thick in furnace roof side walls and bottoms. Front and back door will be in LI 2800L * 900W * 700H in mining chamber size. Door locations; Up and down movement man hole. Opeating maximum temperature: 700-900'C.

LPG burner sets with LPG bank and control panel supply of 4Nos, 5 burners with blower and fully auto control system. LPG fired ignition, flame sensor and auto cut off imcorporated in a separate controller equivalent to imported control system for air and LPG with auto ignition system and supply of 20+20 cylinder bank with pipeline from LPG cylinder back upto each burner end by using TATA; C class grade matyerial pipe

3HP motor 2 Nos for use to ID fan and 1HP motor use for wet scrabbing. Wet scrabber for gas cleaning system; Thisn system should be enhanced with stainless steel cylinder and SS ID fan (3HP motor * 2Nos with ISI standard) to avoid rusting, vloume of water should be increased for effective scrubbing

Guy supported chimney. This is the cylinder type MS IS - 2062 quality, 8m plate chimney with two quoted of alumnium heat resistance paint externally, 7000mm long bottom cylindrical chimney. It is rested on 16mm MS IS 2062 quality, 100feet thick base flange and stool flange 16mm thick with 12mm gusset support. Cylindrucal chimney mounted on foundation 12Nos * 25mm dia bolt, nut joints. Top 1 cylindrical shell boiler quality 8mm plate into 7000mm. Long base chimney : it is rested 50mm width base flange, top to cy7lindrical shell boiler quality 6mm plate into 7000mm long base chimney it is rested 50mm with base flange and wind force curtain MS flash sheet with lightning arrester 25mm *3mm copper flat earthing with easy hinges type Manual opened man hole door. Necessary for polution control board monitoring, sample ports arranged lader assembly with safety guards set 70feet full height. 1seets of ditachable platform overall size 8mm dia* 400mm dia * 21000mm length

Erection and commissioning charges for furnace, burner, wet srubber, chimney including labour and material for fixing