GE/CHM-94/2022-2023 SPECIAL REPAIR TO MD ACCN IN SECTOR C, ADDN/ALTN TO MD ACCN IN SECTOR E AND OTHER SANCTIONED WORKS UNDER AGE B/R III AT CHANDIMANDIR

Amount

Taking down wooden chowkhats or frame n.exc 1.5 Sqm with shutter (without taking off shutters from the frame) and removal from site complete all as specified & directed.

Taking down wooden chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm with shutter (without taking off shutters from the frame) and removal from site complete all as specified & directed.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm and removing to store complete all as specified and directed.

Taking down and re-fixing of shutters of any type description exc 1 sqm but not exc 2 sqm each in same opening after securing or easing & adjusting complete all as specified & directed.

Pressed steel frames 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including fill of PCC 1:3:6 complete all as specified and directed.

Pressed steel frames 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including fill of PCC 1:3:6 complete all as specified and directed.

35mm thick flush shutters, solid core costruction, with block board core and plywood face panels, commercial type on both sides as in cupboards, etc. complete all as specified and directed.

35 mm thick, factory made, second class hard wood, plain framed hammer marked, panelled shutter (two panel)with lock rail and panel of 9 mm BWP commercial ply both face including 1.00 mm thick sunmica (lamination) on both sides of p-anel and 20 mm x 20 mm x 10 mm wooden beading all round the panel. The size of rail and stile as per IS : 1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and directed.

35 mm thick second class hard wood glazed and skelton shutters open rebated and prepared to received gauge/ glass etc, edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc complete all as specified and directed.

35 mm thick second class hard wood half panneled & Half glazed and skelton shutters open rebated and prepared to receive gauge/ glass etc, edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass complete all as specified and directed.

Factory made steel window box type with side hung shutters including box type hinges and one shop coat of red oxide primer, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete with glazing bars, dovetailed or welded fixed with and including MS flat of suitable size for fixing grills and guards bars etc as in repairs, complete all as specified.

Factory made steel window box type with side hung shutters including box type hinges and one shop coat of red oxide primer, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete without glazing bars, dovetailed or welded fixed as in repairs, complete all as specified.

Factory made box type steel ventilators, openable with side hung shutters with box type hinges including one shop coat of red oxide primer, hinges, tower bolts 100 mm, steel handles and steel peg stay complete without glazing bars devetailed or welded, fixed in repairs, complete all as specified and directed.

Galvanised mild steel wire cloth 0.56 mm nominal dia of wire & avg width of aperture 1.18 mm in fixed with tinned tacks complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden, metel frames including punching or drilling out glazing pins/spring clips complete all as specified and directed.

4mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

Solid PVC frame (Single Rebated) of size 75mm x 50mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed. Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed. Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

Factory made solid PVC board 20-22 mm thick as in cup board shelf/ door, sag free thermal and electrically insulated, light weight wrap free, impact resistant, fire resistant, termite resistant, chemically resistant and smell free, complete all as specified and directed.

Factory made solid PVC board 18-19 mm thick as in kitchen cabinet/ cupboard panell with 19mm wide PVC leaping pasted at exposed side, sa free thermal and electrically insulated, light weight wrap free, impact resistant, fire resistant, termite resistant, chemically resistant and smell free complet,e all as specified and directed.

Framed work such as grill guard bars etc welded to steel frame MS round/square bar conforming to Fe 290 Gde-E 165 complete all as specified and directed.

Cutting holes in brick walls built in cement mortar (exc. half brick but not exc. one brick ) and making good the surfaces by cement mortar (1:3) or PCC (1:2:4) type B-1, complete all as specified and directed.

100 mm size butt hinges medium weight cold rolled mild steel complete, all as specified and directed.

100mm butt hinges , extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed for PVC door, type C-21 complete all as specified and directed.

Continuous (Piano) hinges of size 30mm (width of flap when open) , mild steel , complete all as specified and directed.

125mm hasp and staple,aluminium anodised, wire type, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

200 mm size aluminium , barrel tower bolt of extruded section and fixed complete all as specified and directed.

150 mm size aluminium, barrel tower bolt of extruded section and fixed for PVC door complete all as specified and directed.

150 mm aluminium handles cast type complete all as specified and directed.

250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed,complete all as specified and directed.

300mm MS ordinary rat tail rod pattern spring incl roller plate complete all as specified and directed.

Magic eye of size suitable for wooden door complete, all as specified and directed.

Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed.

Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide, zinc chrome complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

Preparation of old steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Brick work with sub class ‘B’ bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg / Sqcm) old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Taking down existing plaster of any description on brick wall/ concrete surface including racking out joints, hacking for key, scrubbing down with water etc complete, all as specified and directed.

Dubbing out average 15mm thick on irregular faces of walls, exposed reinforced surfaces, in CM 1:4 complete all as specified and directed.

Rendering 5mm thick in CM 1:3 on fair faces of concrete/brick surfaces as in ceiling, chajja, etc. finished fair and smooth complete all as specified and directed.

Rendering 15mm thick in Cement and Sand mortar 1:6 over brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

15mm thick rendering in Cement and Sand mortar 1:4 over brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

Racking out joints/ pointing to brick work built in cement mortar, in walls etc and flush pointing in cement mortar 1:3 to brick wall complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of primer complete all as specified and directed.

Three coats of white wash on ceiling surfaces including preparation of new plastered surfaces complete all as specified and directed

Preparation of new plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

One coat of white wash on ceiling surfaces including preparation of old surfaces complete all as specified and directed.

One coat of white wash on wall surfaces including preparation of old surfaces complete all as specified and directed.

Complete removal of existing treatment by using of wire brush /mechanical grinder including preparation of old surfaces of walls and applying two coats of oil bound distemper, complete all as specified and directed

Complete removal of existing treatment by using wire brush /mechanical grinder including washing rubbing down and stopping of distempered or painted surfaces and applying two coats of cement base paint incl necessary curing on wall surface of any description complete all as specified and directed.

25mm thick cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

Demolition of un-reinforced cement concrete exc 15cm thick on any description and in any position not other wise specially provided for ,complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors, beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed.

Reinforced cement concrete type B-1, 1:2:4 (nominal mix, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete all as specified and directed Note : Reinforcement and form work shall be measured and paid separately

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs rough finished surface of concrete flat not exc 200mm thick complete all as specified and directed.

Plain cement concrete 1:5:10 type E-2 using 40mm graded brick coarse aggregate as in sunken floor filling and mass concrete complete all as specified & directed.

Water proofing treatment to sunken portion and adjoining walls of kitchen, WC, Bath & Toilet, etc complete all as specified as under:- (a) 15 mm plaster in cement mortar (1:3) mixed with water proofing compound as per manufacturer’s instructions after roughning and cleaning the surface . (b) Curing the sunken portion with water minimum for 48 hours by ponding. (c)Applying 3mm thick APP membranne with bitumen by torch application to the treated sunken surface over a coat of primer as per manufacturers instructions. (d) Joints/Traps/WC/soil pipes shall be properly sealed with approved sealing compound .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick bedding layer in CM 1:6, complete all as specified and directed.

Glazed ceramic coloured tiles of size 300mmx450mmx 7mm thick as in dado, set and jointed in neat cement slurry and grouted in white cement complete as on vertical surfaces over and including 10 mm thick bedding layer in CM 1:4 complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick screed or bedding layer in CM 1:6, complete all as specified and directed.

Dismantling of stone slabs of any description in floors laid, bedded and pointed in any mortar complete all as specified and directed

Baroda green marble 15 to 17mm thick, machine cut, laid over and including 10mm thick screed bed in cement mortar (1:4), bedded and jointed with grey cement slurry and pointed with grout of matching shade including moulding and all necessary cutting and machine polishing (table rubbed and polished), as in kitchen platform, step, jambs, pillars and like, complete all as specified and directed.

Material and labour machine cut Kota Stone Slab flooring, 18 to 20mm thick, best quality (one piece in stair case tread) over and including cement screed bed 20mm thick in cement mortar 1:6, laid and jointed with grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab, cutting, rubbing, grinding and polishing (mirror finish) complete all as specified and directed.

Machine cut kota stone slab flooring 18-20mm thick of one piece in stair case, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab,as in in skirting, dados, risers to steps, pillar etc, laid over and including 10mm screed layer in cement mortar 1:4, cutting, rubbing, grinding and polishing complete, all as specified.

Making holes into or through concrete slabs/ stone slabs 150 mm long for 25mm dia pipe as in cooking plateform, incl making good the surface complete all as specified and directed.

Cast iron nahani traps 100mm dia with grating including jointing to waste pipe with run led jointed and setting/fixed in cement concrete type B-1 1:2:4 fixed as in repair complete all as specified and directed.

Wash hand basin, vitreous china, flat back, white of size 550 x 400 mm with waste coupling, angle brackets, PVC connection 15mm size, 450mm long, PVC waste pipe, fixed as in repair complete all as specified and directed.

Vitreous China Wash down water closet (pedestal pattern), white with and including PVC seat cover, complete all as specified and directed.

Vitreous china squatting pan, “Orissa” pattern size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe complete including trap, set with cement fixed in repair complete all as specified and directed.

100mm dia bore traps 'P' or 'S' complete all as specified and directed.

White PVC valveless flushing cistern (Duel type) of capacity 10 litres, syphonic action , low level with inlet, ball valve, float, handle, PVC connection & 32mm dia CP flush pipe (long type for squatting pan) incl brackets, as in repairs, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts of length 450mm long as in repairs complete all as specified and directed.

Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190gms), fixed as in repair complete all as specified and directed.

Towel ring of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 90gms), fixed as in repair complete, all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with CP bracket guard and railing 60cm long, fixed as in repairs, complete all as specified and directed.

Grating doom 100mm dia of PTMT, fixed to floor trap with cement mortar 1:3, fixed as in repairs, complete all as specified and directed.

Plate rack of stainless steel sheet 1.0mm thick of size 750mmx 600x250mm with steel shelves and hanging arrangements for utensil, fixed as in repairs, complete all as specified and directed.

Kitchen sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and CP waste coupling, overall size 915mm x 460mm x 203mm, with bowl of size 405mm x 354mm x 203mm incl fixing cantilever brackets, fixed as in repairs, complete all as specified and directed.

Taking up or down steel tubing and connections 15mm bore, complete all as specified and directed.

Taking up or down steel tubing and connections 20mm bore ,complete all as specified and directed.

15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors ,complete all as specified and directed.

Refixing old steel tubing of 15 mm bore and connections in new or old position (walls, ceilings, floors etc.) including cleaning ,complete all as specified and directed.

20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

Refixing old steel tubing of 20 mm bore and connections in new or old position (walls, ceilings, floors etc.) including cleaning, complete all as specified and directed.

16 mm (outer dia) CPVC pipes, SDR 11 and Plain CPVC SDR 11 fittings, fixed on walls/ceiling or laying in floors, complete all as specified.

20 mm (outer dia) CPVC pipes, SDR 11 and Plain CPVC SDR 11 fittings, fixed on walls/ceiling or laying in floors, complete all as specified.

Brass Elbow 16 mm for CPVC Pipe, all as specified.

Brass Elbow 20 mm for CPVC Pipe, all as specified.

Brass Elbow (3/4 X ½) for CPVC Pipe, all as specified.

Brass Tee 16 mm dia UPVC pipe,, all as specified.

Brass Tee 20 mm dia UPVC pipe, all as specified.

Male Brass Threaded Adaptor 16 mm dia (MTA/ MBTA) for CPVC pipe, all as specified.

Male Brass Threaded Adaptor 20 mm dia (MTA/ MBTA) for CPVC pipe, all as specified.

Female Brass Threaded 16 mm dia Adaptor (FTA/ FBTA) for CPVC Pipe, all as specified.

Female Brass threaded 20 mm dia adaptor (FTA/ FBTA) for CPVC Pipe, all as specified.

Tank adapter16 mm dia for CPVC Pipe, all as specified.

Tank adapter20 mm dia for CPVC Pipe, all as specified.

Union 16 mm dia for CPVC Pipe, all as specified.

Union 20 mm dia for CPVC Pipe, all as specified.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

PVC (SWR) rain water pipe, 75mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

75 mm bore PVC (SWR) bends of any radius complete, all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc and cutting chases for concealed water tubing & making good, cutting not exc 10 cm girth, in brick walls complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 20mm bore pipe, fixed as in repairs complete all as specified and directed.

Bib taps brass, fancy type, Short body with wall flange, standard chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Bib taps brass, fancy type, long body with wall flange, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve (concealed type), chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Wash hand Basin brass Mixer of chromium plated hot and cold water screwed down for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair, complete all as specified and directed

Chromium plated, fancy type shower rose with swivel joints 125mm dia with arm and fixing to steel pipe 15mm bore, fixed as in repairs, complete all as specified and directed

Taking down rain water pipes (any types) including all fittings any size and pattern complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, complete all as specified and directed.

110 mm bore PVC (SWR) bends of any radius complete, all as specified and directed.

Dismantling of existing brick tiles or terracing tiles single layer on roof grouted in cement mortar including removal of any existing treatment complete all as specified & directed.

Demolition of mud phuska as in roof of any thickness incl plastering and leeping etc (whether full thickness removed or only a part thereof) complete all as specified & directed.

Plain cement concrete 1:2:4 type B-1(20mm graded stone aggrete) as in roof padding, terraces and in other similar locations as per site requirement , complete all as specified and directed.

Supply only water proofing compound, ISI marked complete all as specified and directed.

3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gm/sqm) laid over a coat of bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS. The membrane shall be laid using butane torch and sealing all joints etc after preparing the surface as per standard practice and as per manufacturer instructions including dismantling of existing felt /treatment, complete all as specified & directed.

40mm thick brick tiles over and including 20mm thick Cement mortar 1:4 joints, grouted & pointed flush as the work proceeds mixed with crude oil 5% by wt of cement complete all as specified and directed.

All as per item No 127 here-in-before but except tiles.

Plain cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in roof kerbs of mud stops, rounded or chamfered on edges usingincluding necessary form work, complete all as specified and directed.

20mm dia anodised aluminium alloy curtain rod including fixing fancy types brackets, stops, rollers etc., as in repairs complete all as specified and directed.

Float valve/ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed for 20mm bore pipe (minimum weight 210 gms), fixed as in repairs, complete all as specified and directed.

500 Litres capacity Rotational moulded polythene water storage tanks (cylindrical vertical with closed top) double layered hoisted and fixed in position including PTMT ball valve 20mm bore & PTMT tank nipple, etc, fixed as in repairs, complete all as specified and directed.

Wire brushing and cleaning top surface, terracing or cement concrete, includng flashings and junction of parapets etc including 3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid over a coat of oil boubd bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS. The membrane shall be laid using butane torch and sealing all joints etc having 75mm side lap joint and 100m end lap joint after preparing the surface as per standard practice and as per manufacturer instructions and finished with applying two coats of bituminous aluminium paint @100gm/sqm on top of membrane, complete all as specified & directed.

Rendering 20mm thick (average thickness) plaster in cement mortar 1:4 mixed with WPC on concrete roof surfaces including flashings and junction of parapets etc , finishing the surface even and fair without using extra cement all as specified and directed by Engineer-in-charge. Note :- WPC will be measured & paid separately as supply only).

Surface dressing in any type of soil, not exceeding 15cm deep and getting out , all as specified.

Excavation in post holes (or similar hole) each in hard and dense soil, n.exc 0.50 cu m getting out and removing surplus spoil at a distance not exc 50 metre and making good surfaces complete all as specified and directed.

50mm thick PCC 1:4:8 type D-2 (using 40m graded crushed stone aggregate) as in sub base flooring, finished even ,all as specified and directed.

Hard core of gauge of broken stone or boulders, not exc 63mm , deposited spread and lavelled in layers n-exc 25 cm watered & rammed to a true surface ,complete all as specified.

Plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete, all as specified & directed.

Steel work in tubular trusses and tubular posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 , complete all as specified & directed by Engineer-in-Charge.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Machine pressed Concrete interlocking paver block, with grey cement and no pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning , complete all as specified and directed

Machine pressed Concrete interlocking paver block, with grey cement and pigment, design as approved, any shape and size conforming to IS 15658-2006 of 80 mm thickness, M-40 Grade laid over and including 25mm thick sand cushioning , complete all as specified and directed

Precast kerb stone edging, using factory made pre cast kerb stones (M-20 concrete) of size 300 x 100 x 300mm (laid with width equal to 100mm), set and jointed in CM(1:4), all as specified and directed.

Plain cement concrete type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in seismic and other similar bands, shelves, copings, bed plates, hold fast, plinth courses and the like finished fair & even, including necessary formwork complete all as specified.

Moram /sand filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering , all as specified and directed.

Taking down carefully aluminum/copper point wiring on & including hard wood battens, surface conduit and board/blocks etc or through conduits for light , socket or power point ,fan point complete incl fitting such as switches ,sockets, ceiling rose , holder socket, light fitting, regulators and making good disturbed surfaces of wall, floor , ceiling etc and removing materials (other than those for which credit has been given by the contractor) to the MES stores yard for keeping in safe custody complete all as specified and directed.

Point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original and nothing extra shall be paid on this account. Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account.

All as per serial item 149 herein before but for socket outlet 3 pin 6 Amps on same board complete all as specified and directed

All as per serial item 149 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 149 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Switch piano, flush type, 6 amps, 230 volts, single pole, one way (ISI marked) complete all as directed by Engineer-in-charge

Switch piano, flush type, 16 Amps, 230 volts, single pole, one way (ISI marked) complete all as directed by Engineer-in-charge

Sockets outlet multipurpose 2 in 1 pin, 6 and 16 Amps flush type ISI marked all as specified and directed by Engineer-in-charge

Sockets outlet multipurpose 2 in 1 pin, 6 and 16 Amps flush type ISI marked all as specified and directed by Engineer-in-charge

Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

Lamp holder, PVC/Polycarbonate type with back plate angular type fixed on wall suitable for batten fitting ,complete all as specified and directed.

LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete, fixed in repairs, all as specified..

LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete, fixed in repairs, all as specified.

LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, fixed in repairs, all as specified..

Electric Bell, AC, 230 volts, single pole all as specified and directed by Engineer-in-charge.

Bell push, paino type, 6 amps, 230 volts, single pole, complete all as directed by Engineer-in-charge

Stepped type electronic fan regulator flush type complete all as specfied and directed.

LED retrofit lamp, 7 watt based PVC/Polycarbonate type with back plate angular type fixed on wall suitable for batten fitting ,complete all as specified and directed.

Disconnecting the power supply and taking down carefully by unscrewing from boards fittings and fixtures such as DBs, Junction Box, Panels of any size complete with all MCCB's ,MCB's etc and removing from site, all as specified and directed by Engr-in charge.

MCB DB, having IP 43 protection Powder coated double coated flush mounted complete with locking arrangement suitable for 8 way SPN with 200 Amp rated busbar 230 V AC complete all as specified and directed.

MCB ,SPN, 240 volt, 40Amps, 10 KA , 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

Premier Constructions

M/s Om parkash

PARVEEN KUMAR AND SONS

KUNDRA CONSTRUCTIONS

Standard Const. Co.

M/s Hari Om Engineer and Contractor