CERTAIN REPAIR TO ROOF JOINERY FLOORING CEILING PLASTERING SAINITARY FITTING WATER TANK CLEANING AND ALLIED SERVICES AT 4 3 GR 87 MTN BDE SIG COY OTM ACCN UNDER AGE BRI GE SOUTH UDHAMPUR

Amount

Material and labour for cleaning the entire roof surface thoroughly to remove all loose particles, dust/dirt particles and applying with One coat of industrial bitumen 85/25 grade at the rate of 1.20 Kg/Sqm over the plastered surfaces of roof all as specified and as directed by the Engineer-in-Charge.

Material and labour for 3mm thick APP based polymeric membrane minimum weighing 3 kg/sqm non-woven polyester reinforcement polymeric water proofing membrane (wt not less than 150 gms/sqm) laid on primed surfaces by gas flame torch application and apply one coat of industrial bitumen 85/25 grade at the rate of 1.20 Kg/Sqm over APP Memberence complete all as specified and as directed by the Engineer-in-Charge. Note :- Water proofing treatment will be done by IWL or through a specialized agency which will further have to give a five years warranty for rectification of any defect if incurred at a later stage, otherwise no payment shall be made to the contractor if water proofing treatment is executed by engaging local labour.

Material and labour for Applying a coat of bituminous aluminium paint @0.10kg/Sqm as weather proof coat all as specified and as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish of the premises complete all as specified and directed.

M&L for glazed coloured ceramic tiles in dado/vertical surface size 600mmx300mmx9-10mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface including 10 mm thick rendering as backing coat to receive the tiles on fair faces of brick /concrete surfaces in cement mortar 1:3 and finished even and rough complete all as specified and directed.

M&L Non - Skid Ceramic tiles (square/rectangular) (size400x400x7mm thick joint free)area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thich screed bed or bedding layer in cement mortar (1:4) etc complete all as specified and directed.

M&L for Non skid coloured tiles (square/rectengular) (size 600x600x9-10mm thick joint free) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 15mm thich screed bed or bedding layer in cement mortar (1:4) etc complete all as specified and directed.

M&L for Non skid coloured tiles (square/rectengular) (size 1200x600x9-10mm thick joint free) area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 15mm thich screed bed or bedding layer in cement mortar (1:4) etc complete all as specified and directed.

All as per item No 8 above but on vertical surfaces as in skirting including 10 mm thick rendering as backing coat to receive the tiles on fair faces of brick /concrete surfaces in cement mortar 1:3 and finished even and rough complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick (size 600mmx600mm) over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 20mm thich screed bed or bedding layer in cement mortar (1:4), rubbing and polishing and moulding etc. complete all as specified and directed. Note :- Machin cut kota stone is to be laid on the stair in single piece.

M&L for machine cut kota stone 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 15mm thich cement screed or bedding layer in cement mortar (1:4), rubbing and polishing etc. complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L Granite slab 16 to 18 mm thick as in pillars, window cill, cooking platform and the like in cement motar 1:4 including painting in white cment 1:2 using marble dust with a mixture of pigment to match the shade of granite including cutting polishing and moulding on edges complete all as specified and directed.

M&L for Rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions height of bldg upto 7.50 mtr including scapfoldings complete all as specified and as directed. (Water proofing compound to be measured and paid for separately).

M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified and directed.

M&L for Rendering 5mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt ), all as specified and directed by Engineer-in Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed by Engineer-in Charge.

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for providing cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified and as directed.

M&L for factory made, 2nd class hard wood 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

All as per item No 24 above but glazed and skeleton shutter with sash bar for glass / wire gauge complete all as specified and as directed.

S&F steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and as directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Description all as per item as above here in before but without glazing bar complete all as specified. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately

S&F factory made mild steel ventilators box type with upper top hung shutters and bottom fixed type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all as specified and as directed. Note :- i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks and similar work conforming to Fe 290 Gd E-165 complete all as specified and as directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

S&F 4 mm thick sheet glass frosted ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal and average width of apreture 1.40mm and fixed with tinned teaks or wire staple complete all as specified and as directed.

M&L for rolled mild steel work of angle iron as in frames of doors & Cup Board & Iron ladders etc conforming to grade Fe 410-O or Fe-310-O complete all as specified and as directed.

S&F Hard Drawn steel wire fabric cut to length bent to shape required and tying,welding to the angle iron frame etc complete all as specified and directed.

S&F 19mm thick ISI, termite proof , chemically well pressed, prelaminated particle board(HDHMR) exterior grade prelaminated, one side with decorative choice lamination and other side balancing white lamination fixed with screws to frame work for kitchen cabinetstand cup boards etc includimg 6mm thick wood beading all around complete all as specified and directed.

Demolition of brick/stone masonry built in CM complete all as specified and as directed.

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed by Engr-in-charge. Note PCC Bond Stone shall be paid separately under appropriate item and volume of bond stone shall be deducted complete all as specified and as directed.

All as per item No 36 above but except stone complete all as specified and as directed.

M&L for Precast cement concrete Block (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in bond stones set in cement mortor 1:6 all as specified and directed.

Extra over stone walling for hammer dressing with miximum depression on face from straight edge held against the dressed surface not exceeding 20 mm to face stones (Granite or Trap stone) and dressing of face beds and joints, as specified of random rubble walling, uncoursed or brought upto courses complete all as specified and as directed.

M&L Flush pointing to random rubble masonry in CM (1:4), uncoursed or brought upto courses complete all as specified and directed.

M&L brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 complete all as specified and as directed.

M&L brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 but except bricks complete all as specified and as directed.

M&L half brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:4 all as specified and directed.

M&L Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F continuous MS CP piano type hinges 30mm flap (when opened), bright finish or electrogalvanised complete all as specified and as directed.

S&F Aluminium handles, cast type, 150 mm long complete all as specified and as directed.

S&F 100mm size hasp and staple safty type aluminum anodized with mild steel hinges pin including bolt to hinge plate and fixed with screw complete all as specified and as directed.

S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed.all as specified and directed.

S&F 250 mm mild steel ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F stainless steel curtain Rods, 25 mm Dia, chromium plated with fixing brackets, stops, rollers etc complete all as specified and as directed.

S&F solid mouled PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube and fixed in opening as per specification and drawing on page No. 150 MES SSR-2004 Part II including taking down old frames with doors complete all as specified and as directed.

S & F factory made solid PVC moulded door shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, fixing in frame at site as per specification & drawingcomplete all as specified and as directed.

S&F vitreous China wash basin corner, white, flat back, size 550x400mm excluding tap, chain, plug but including brackets, waste fitting 32mm dia ,brass chromimium plated for glazed ware sink, basin,with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

M&L for preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for preparation of steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed.

M&L for applying two coats of white washing on ceiling including preparation of new/old plastered surfaces complete all as specified and as directed.

M&L two coats of oil bound distemper on walls including preparation on new/old surfaces including applying 1 mm thick layer of wall putty on walls to give uniform surface complete all as specified and directed. Note :- (Before applying of wall care putty, complete removing of treatment as directed and approved by Engr-in-charge).

Material and labour for preparation of New plastered surfaces of walls and applying two coats of cement based paint white or tinted complete all as specified and as directed by Engr-in-charge.

S&F vitreous China wash down water closet pan pedestal pattern, white (excluding fixing bolts, flushing cistern and flush pipe) with P or S trap but including plastic water closet seal, seat cover ,white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device including connection to drain and flush pipe complete all as specified and as directed.

S&F in repair 10 ltr PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

Supply only flush pipe of PVC 32 mm dia for low level cistern complete all as specified and as directed.

S&F MS grating 100mm dia fixed to floor trap complete all as specified and as directed.

M&L 600 mm long brass chromium plated towel rail fancy type complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of lengh 450mm complete all as specified and as directed.

S&F steel peg set colour coated of six as per sample complete all as specified and as directed.

S&F Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F plate rack made of stainless steel, 600 x 750X0.55mm including fixing as per manufacturers instruction complete all as specified and as directed.

M&L PCC 1:5:10 type E2 using 40 mm graded brick aggregate as in filling under sunken floors etc complete all as specified and as directed.

Dismantling cast iron pipe & reinforced concrete drain pipes, jointed in cement mortar of any dia upto 100mm complete all as specified and as directed.

PVC (SWR) pipes 110mm bore single socketed , in any length with rubber ring joints fixed to wall complete all as specified and as directed.

PVC (SWR) pipes 75mm bore single socketed , in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S&F PVC (SWR) bend any radius for 110mm bore pipe complete all as specified and as directed.

S&F PVC (SWR) bend any radius for 110mm bore pipe complete all as specified and as directed.

S&F PVC (SWR)branch piece single (single Y ) equal or unequal for 110mm bore pipe complete all as specified and as directed.

S&F PVC (SWR)branch piece single (single Y ) equal or unequal for 75mm bore pipe complete all as specified and as directed.

S&F PVC (SWR) junction single (single T ) equal or unequal for 100mm bore pipe complete all as specified and as directed.

S&F PVC (SWR) junction single (single T ) equal or unequal for 75mm bore pipe complete all as specified and as directed.

S&F PVC (SWR) reducers for100mm bore pipe complete all as specified and as directed.

S&F PVC (SWR)'P' Trap for110mm bore pipe complete all as specified and as directed.

Hacking out old broken glass panes (any thickness, size quality or description) from wooden frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

S&F 4 mm thick sheet glass frosted ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

Dismantling wall and ceiling boards, fibre pulp insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

Providing and fixing flase ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2% humidity resistance of 99%, NRCO 0.50 to 0.75 as per IS 8225 : 1987, non combustible as per BS 475 (Part 4)-1970 and light reflectance of 85%(minimum) to be laid in true horizontal level suspended on interlocking metal T Grid of hot dipped galvanized iron section of 0.33mm thick (galvanised @ 120 grams per sqm both sides) comprising of main T runners of size 15 x 32 mm of length 3000 mm, cross T of size 15 x 32mm of length 600 mm x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e 50 mm long, 12 mm outer diameter M-6 dast fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x 0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specificatins, drawing and as per directions of Engr-in-Charge

Dismantling of plain or corrugated steel sheeting any gauge and thickness including Nainiital or similar pattern roof coveriongs complete all as specified and as directed.

S & F Pre painted galvalume alumiium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strenth of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed.

M & L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n. exc 15 cm thickness below or above GL complete all as specified and as directed.

M & L Providing 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) in sub base of flooring complete all as specified and as directed.

M&L 25 mm thick PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) as in laying of floor finishes and finishing even complete all as specified and as directed.

M & L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) in plinth protection and paving complete all as specified and as directed.

M & L for 100mm thick cement concrete type B 2 PCC (1:2:4) (using 40 mm graded aggregate) as in hard standing finished even and smooth without using extra cement and spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

M&L for Glass dividing strips, 3mm thick of 38mm width complete all as specified and directed.

Demolition of reinforced cement conrete (reinforcement cut as required to facilitate demoletion) of roofs, floors (other than ground floors), beams, staircases, landings, chajjas and similar suspended work complete all as specified and as directed.

M&L (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in beams, cantilever, bressummers, lintel over 1.5m span etc complete all as specified and as directed.

M&L for precast cement concrete 1:2:4 type B-I using 20 mm graded stone aggregate as in Roof & cover slabs, (for man holes) chullah hoods, chajjas, shelves and similar articles with plain faces and set in mortar 1:6 complete all as specified and as directed.

Use and waste of formwork to soffits of floor or roof beams, beam haunching, grider, bressumber, lintels, cantilever, sleves including supports, over hang etc also splay between floor and beams to rough finish surface of concrete flat complete all as specified and as directed.

M&L mild steel TMT bars 8 to 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Complete all as per item No 102 above item but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

S&F for Powder Coating anodised aluminum frame of doors, windows, ventilators with one or more rebates including joining cleats for fixing etc. complete all as specified and as directed.

S&F for Powder Coating anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges anodised alumnium snap beading, screws etc. complete all as specified and as directed.

S&F for Powder Coating anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg /m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc complete all as specified and as directed.

Supply and fixing powder coatedAnodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

Supply and fixed in repair aluminium (extruded section body) door closer hydraulically regulated designation No-3 universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F in repair 150 mm long aluminium handles, cast type anodised, complete all as specified and as directed.

S&F in repair Butt hinges 100 mm size, extruded aluminium alloy with galvanised mild steel hinge pins, anodised and fixed, type B-21 complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality and fixed with aluminum beading and gaskit suitable for aluminum frames in squares not exceeding 0.5 sqm in each pane complete all as specified and directed.

S&F aluminium grill of mesh size 50 mm x 50 mm fixed to aluminum window frame complete all as specified and direceted.

S&F10 mm thick sheet Toughned glass as in hinged door ,partition automatic doors and similar work including cutting to shape,drilling holes required ordinary quality and fixed with aluminum beading and gaskit suitable for aluminum frames complete all as specified and directed.

M&L for rolled mild steel work of angle iron as in frames of doors , coolar stand ,Cup Board,stairs & Monkey Guard etc conforming to grade Fe 410-O or Fe-310-O complete all as specified and as directed.

S&F Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100/110mm bore pipe complete all as specifiecd and directed.

S&F Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore complete all as specified and as directed.

M&L for Reinforced cement concrete (Nominal Mix) type B1 1:2:4 using 12.5mm graded stone aggregate as chajjas , slabe or similar works etc completed all as specified and as directed.

Taking up or down 15mm bore steel tubing with connections for cleaning for refixing or removing to store yard complete all as specified and as directed.

Taking up or down 20mm bore steel tubing with connections for cleaning for refixing or removing to store yard complete all as specified and as directed.

M&L 15mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified and directed.

M&L 20mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified and directed.

M&L Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm complete all as specified and directed.

M&L Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15mm complete all as specified and directed.

S&F fancy type chromium plated angle valve cast copper alloy, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions chromium plated of size 15 mm. complete all as specified and directed.

S&F of Bib tap cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe of size 15mm bore chromium plated complete all as specified and directed.

Ball valves PTMT of size 20 mm bore dia high pressure of with polyetylene float and flynut screwed for iron pipe and fixed including necessary fitting as required at site in repair complete all as specified and directed by Engr-in-Charge.

S&F as in repair chromium plated shower roses 125 mm long with or without swivel joints, any size, including fixing fixing to steel pipe or union complete all as specified and direceted.

Dismantling water tanks and removing to store exc 500 & n.exc 1000 ltrs of capacity complete all as specified and directed.

Dismantling water tanks and removing to store exc 1000 & n.exc 2000 ltrs of capacity complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks white colour , triple layer ( cylindrical vertical with thread closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 liters including all accessories complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks white colour , triple layer ( cylindrical vertical with thread closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 liters including all accessories complete all as specified ..Make : Vectus , Sintex and supreme complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks white colour , triple layer ( cylindrical vertical with thread closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 2000 liters including all accessories complete all as specified and directed.

S & F in repairs 15 mm dia WHB mixer centre hole chromium plated screwed down high pressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specifie and as directed.

S &F sheet glass shelf assembly/corner consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plate bracket guard and railing 60 cm long in repair complete all as specified and directed.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S & F in repairs 15 mm dia wall mixer chromium plated screwed down high pressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specifie and as directed.

M&L, Hard core of broken stone or boulders of gauge exc 63 mm but n exc 100 mm deposited spread and levelled in layers n exc 15 cm thick watered and rolled / rammed to a true surface complete all as specified and directed.

M&L for sand cushion 30 to 40 mm thick for laying and fixing interlocking tiles complete all as specified and directed.

M&L for 80mm thick machine pressed / vibro mechanically floated interlocking paver block any shape and size conforming to IS - 15658-2006, M-35 grade, with topping of cement mixed without pigment. Colour and shape shall be approved by Engr-in-charge.

M & L for Chequered cement concrete tiles 300x300x 25 to 30 mm thick, set, jointed and pointed in neat cement slurry in floors, set jointed and pointed in neat cement slurry as in path with grey cement and no pigment etc including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F Vitrified Dura stone tiles of size 300 x 300 x 10mm thick as in floors and over & including 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair and 15mm thick screed bed or bedding layer in cement mortar 1:6, including jointed with neat cement slurry and pointed in coloured cement to match the surface of tiles, complete all as specified and directed

Welding in repairs to windows, door hinges, grills etc exc 2.50 cm of thickness not exc 6mm complete all as specified and directed.

Material and labour for preparation of old plastered surfaces of walls and applying two coats of cement based paint white or tinted complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of old decorated wall surfaces by washing rubbing down and stopping of distempered surfaces and filling the nail holes by white cement and applying Two coat of oil emulsion distemper white or tinted with roller application complete all as specified and as directed by Engr-in-charge.

M & L for cleaing and removing all scale and dirt etc, from tanks exceeding 500 & n.exc 1000 ltr capacity of tank from mouths of circulating pipes complete all as specified and directed.

M & L for cleaing and removing all scale and dirt etc, from tanks exceeding 250 & n.exc 500 ltr capacity of tank from mouths of circulating pipes complete all as specified and directed.

S&F in repairs Single Piece WC with UF soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings, Size: 370x695x795 mm, S trap-300mmr as approved and complete all as specified and directed by Engr-in-Charge .

vmd traders (BID ID -3325932)

ARNABH ASSOCIATES (BID ID -3326645)

kerni electricals (BID ID -3326478)