C/O Sub Market Yard at Sujanpur, Distt. Hamirpur, H.P. SH-C/O Office, Kissan Bhawan/residence, Toilet block, W.S. and S.I. and Channelization of Nalah.

Amount

(Channelization of Nallah) Excavation in foundation trenches etc. in earth work in all heights and depth in all kinds of soils, including saturated soil comprising of pick work, jumper work, and blasting work both in soft and hard rock with chiselling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the Engineer -in-Charge at site. according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and un- useful material and transportation of the un -useful material for disposing at approved dumping site or otherwise and including payment of prescribed charges of dumping to the owner of dumping site (to be arranged by the contractor) satisfaction of Engineer- in -Charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour ,machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour (if required ).

Providing and laying Mechanically mixed & vibrated cement concrete 1:4:8 (1: cement :4 sand: 8 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of from work in foundation and plinth, including carriage of material within all leads and lifts as per direction of Engineer-in-charge

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu reinforced concrete & plain concrete work in: including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all iincidential charges.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by govermentb) Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Providing and laying cement concrete 1:1.5:3 (one cement into one point five sand into three crushed stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mixed and vibrated, curing complete excluding cost of form work and reinforcement for reinforced concrete work and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge in wall (any thickness but not less than 0.1 m thickness) attached pilasters, buttresses, plinth and string courses etc. upto floor two level.

Backfilling behind abutment wing wall and retaining wall complete Filter as per drawings & technical specification clause 1204.3.8 with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Excavation in earth work and banking in 20cm. Layers including breaking clods, ramming and dressing ground for the purpose of making embankment or filling up ground depressions upto all lead and lifts.

Providing mild steel / tor steel reinforcement for R.C.C. work including binding wire, cutting, bending, binding and placing in position complete upto all floors level including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Stone soling properly hand packed filling interstices with Kharanja stone and consolidating by ramming manually to the required gradient and camber including spreading ,watering and rolling of binding materials moorum or earth etc. including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and laying Mechanically mixed & vibrated cement concrete 1:3:6 (1: cement :3 sand: 6 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of from work in foundation and plinth, including carriage of material within all leads and lifts as per direction of Engineer-in-charge

Providing and laying of interlocking concrete block pavements ISI marked having thickness 80 mm (M 50 grade ) as per drawings and technical specification clause 1504, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Office Kissan Bhawan/Residence and toilet block Providing form work with steel plates 3.15mm (three point one five millimetre) thick welded with angle iron in frame 30x30x5mm ,so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden / steel battens and ballies, height of propping and centring below supporting floor to ceiling up to all heights and removal of the same for insitu-reinforced concrete & plain concrete work. Columns, pillar etc. Square, rectangular, polygonal in plan. including carriage of material within all leads and lifts as per direction of Engineer-in-charge in:-Foundation footing and basis of columns.

Beams, cantilever, girders and lintels:- Side and soffits of beams, beam haunchings, cantilevers bressumersand lintels not exceeding 1meter in depth in all heights from floor.

Providing and laying mechanically mixed and vibrated cement concrete Mix 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement bases of columns and the like and mass concrete. Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers in all heights & all floor level.including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Columns pillars, posts and struts, upto floor to level

Providing second class bricks work using common burnt clay building bricks in super structure above plinth level above in all floor level in: Cement mortar 1:6 (1 Cement :6 Sand) curing complete, including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Second class Half brick masonary in common burnt clay building bricks in superstructure in all floor levels in cement mortar 1:4 (1 cement : 4 sand) including carriage of material in all leads and lifts :- Second class brick

Providing wood work in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position including entire, including carriage of material within all leads and lifts as per direction of Engineer-in-charge.Sal wood.

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embeding in cement concrete block 10x10x15cm. 1:3:6 (1 cement:3 sand:6 graded stone aggregate 20mm nominal size), including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing flush door shutter interior grade , commericial type, core of black board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bend and face veneers on both faces of shutter as per HP.PWD specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One), including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all iincidential charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government . a)40mm thick

Providing and fixing panelled glazed or panelled & glazed shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws including carriage of materials in all leads and lifts. 35 mm thick 2nd class deodar wood, including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge desigantion 85 G with wire of dia 0.56mm for doors windows and clerestorey windows and including bright finished black enamelled iron hings with necessary screwsd 30 mm thick 2nd class deodar wood including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing M.S. Grills of required paterns in wooden/steel frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. Plain Grill: with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing mild steel / tor steel reinforcement for R.C.C. work including binding wire, cutting, bending, binding and placing in position complete upto all floors level including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

15mm cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 30cm in girth and finished even and sand opapered smooth. including carriage of material within all leads and lifts in all floor levels as per direction of Engineer-in-charge in Cement mortar 1:6 (1 cement : 6 sand)

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior / exterior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 30cm in girth and finished even and smooth including carriage of material within all leads and lifts in all floor levels as per direction of Engineer-in-charge in Cement mortar 1:6 (1 cement : 6 sand).

Kota stone slab flooring 20mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and mirror polishing etc. complete 25 mm thick , including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

White/coloured glazed tiles of size 300 X 450 mm, of approved shade and brand ORIENT / NITCO or equivalent in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry complete including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing anodized aluminium sliding door bolt anodized trans parent or dyed to required shade and colour with screws etc. Complete with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. 250x16 mm.

Providing and fixing aluminium tower bolts (berrel type) anodized transparent or dyed to required shade and colour with screws etc. (a) 150x10 mm, including carriage of material within all leads and lifts.

Providing and fixing aluminium tower bolts (berrel type) anodized transparent or dyed to required shade and colour with screws etc. (b) 100x10 mm, including carriage of material within all leads and lifts.

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with neessary screws etc. Complete 125 mm including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

providing and fixing oxidized M.S hooks and eyes 300mm including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Applying two or more coats of Birla white wall care putty or equivalent over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of material within all leads and lifts in all floor levels as per direction of Engineer-in-charge.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil grease dirt and other foreign matter sand papering and knotting including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Painting two coats (excluding priming coat) on new wood and wood based surfaces, with enamel paint, brushing to give an even shade including cleaning of all dirt, dust and other foreign matter sand papering and stopping with enamel paint other than white including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall / ceiling / slopping surfaces to give an even shade over and including priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth Priming coat with distemper primer including carriage of material within all leads and lifts in all floor levels as per direction of Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its eqivalant on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foeign matter etc. including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing 0.60mm thick prepainted steel sheet of approved TATA (Durashine) of shade and design in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5microns over 5 microns primer coating including fixing with G.I. self drilling screws of required sizes / prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge:-0.60 mm ( zero point sixty millimetre) thick sheet including carriage of material within all leads and lifts as per direction of Engineer-in-charge:-

Providing and fixing ridges or hips 60 cm overall with 0.45mm (Zero point forty five milimetre) thick prepainted steel sheets of TATA (Durashine) of approved shade & design in roofing with hot dipped metalilc zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating+back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I limpet and bitumen washers complete 0.60mm (zero point six zero milimeter) including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Steel work welded in built up sections including , trusses and framed work, including cutting hoisting fixing in position and applying a priming coat of red lead paint including carriage of materials within all leads and lifts in trusses and trussed purlins in buildings.

Steel work welded in built up sections including in trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In gratings framed guard bars, ladders, railling, brackets and similar works,including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and laying mechanically mixed and vibrated cement concrete 1 : 6 : 12 ( 1 cement :6 sand : 12 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in : foundation and plinth including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Sanitary work: Providing and fixing to wall ceiling and floor galvanized mild steel tubes (medium grade) of Jindal (Hissar) or equlent tube fittings ISI and clamps including making good the wall, ceiling and floor 15mm nominal bore, within all leads, lifts of materials and other incidentals as per approved drawing design and as directed by the Engineer-in-Charge.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (medium grade) of Jindal (Hissar) or equlent tube fittings ISI and clamps including making good the wall, ceiling and floor 25mm nominal bore, within all leads, lifts of materials and other incidentals as per approved drawing design and as directed by the Engineer-in-Charge.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (medium grade) of Jindal (Hissar) or equlent tube fittings ISI and clamps including making good the wall, ceiling and floor 20mm nominal bore, within all leads, lifts of materials and other incidentals as per approved drawing design and as directed by the Engineer-in-Charge.

Providing and fixing high pressure PVC (Finolex) spigot and socket waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete. including carriage of materials , within all leads, lifts of materials and other incidentals as per approved drawing design and as directed by the Engineer-in-Charge. 110 mm

Providing and fixing high pressure PVC (Finolex) spigot and socket waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete. including carriage of materials , within all leads, lifts of materials and other incidentals as per approved drawing design and as directed by the Engineer-in-Charge. 75 mm

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete. 110 mm dia, with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete. 75 mm dia, with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete. 110 mm dia with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete. 75 mm dia with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing PVC ( FINOLEX) single equal branch (a) with oval access door, ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive etc. complete ,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. 110 mm dia

75 mm dia door tee.

Provding and fixing PVC cowls 110 mm within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Provding and fixing PVC cowls 75 mm within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Providing and fixing vitreous china wash down water closet (European type.W.C. pan) with integral 'P' or 'S' trap of Cera/ Hindware or its equivalent including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately). within all leads, lifts of materials as directed by the Engineer-in-Charge. Angle Indian Universal closet

Providing and fixing 10.0/12.50/15.00 litres vitreous china low level flushing cistern with a with fitting such as lead valve less syphon 15 mm nominal size brass ball valve with polythene floythene float C.P. Brass handle unions and couplings for connections with inlet outlet and overflow pipes 40 mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) ,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing automtic flushing PVC cistern Cera/Hindware make with a pair of C.I. or M.S. brackets complete with fittings including C.I. syphonic with inlet outlet and overflow pipes including cutting holes and making good the same ( overflow pipe to be measured and paid for separately) vitreous china 5 litres, within all leads, lifts of materials and other incidentals as per approved drawing design and as directed by the Engineer-in-Charge.

Providingl and fixing vitreous china wash basin with single hole for pillar tap with C.I. Or M.S.brackets painted white including cutting holes and making good the same but excluding fitting Flat back 550x400 mm including carriage of material within all leads and lifts as per direction of Engineer-in-charge (550mm x 400mm)

providing and fixing CP brass waste for wash basin and sink 32 mm dia with in all leads, lifts of materials as directed by the Engineer-in-Charge.

providing and fixing PVC waste pipe for wash basin and sink 32 mm dia with in all leads, lifts of materials as directed by the Engineer-in-Charge.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws 750mm x20mm, with in all leads, lifts of materials as directed by the Engineer-in-Charge

Providing and fixing 600 mm x 450 mm bevelled edge mirror of superior glass mounted on 6 mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws & washre of aproved make with in all leads, lifts of materials as directed by the Engineer-in-Charge.

Providing and fixing 600 mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete of approved make fixed to wooden plugs with C.P. Brass screws.with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 100mm sand cast iron graing for gully, floor or Nahni trap with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete 110mm*90mm with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing C.P. Brass bib tap Seiko make or its equivalent with capstan head 15 mm dia , with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing C.P. Brass pillar tap of Seiko make or its equivalent with capstan head 15 mm dia with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing PTMT (Paryag Make) angle valve with Nuts and pipe 15 mm dia with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing chromium plated brass soap dish of approved make with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing P.V.C. connection pipe with brass Unions with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.45cm length, 15 mm nominal Bore.

Providing and fixing brass full way valve with wheel / PVC coated lever complete including carriage of material within all leads and lifts as per direction of Engineer-in-charge:- 15 mm nominal boire.

Providing and fixing brass full way valve with wheel / PVC coated lever complete including carriage of material within all leads and lifts as per direction of Engineer-in-charge:- 20 mm nominal boire.

Providing and fixing brass full way valve with wheel / PVC coated lever complete including carriage of material within all leads and lifts as per direction of Engineer-in-charge:- 25 mm nominal boire.

Constructing manhole with R.C.C top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curring and testing :- (i) Inside size 800mm x 800mm and 500mm deep including C.I cover with grame. (Light duty single seal pattern-1) 455 mm*610mm internal dimension total weight of cover and frame to be not less than 38kg (weight of cover 23 kg and weight of frame 15kg.) with 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement 3: sand) including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing PVC water storage tank of ISI 12701 marked G.I. inlet and outlet connection 15 mm nominal bore ball valve and mosquito proof PVC cover with locking angement including hoisting up to all heights above ground level 1000 litres net capacity tank .including carriage of materials with in all leads & lifts as per direction / satisfaction of the Engineer-in-charge .

VIVEK GUPTA

AMIT KATOCH