Providing Internal, External Electrification, 15 Persons Stretcher cum passenger lift and Disel Generator arrangements to the Additional Building for MCH in Government Hospital at Cheranmahadevi in Tirunelveli District.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module Gl switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points/Coil) (Higher End)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module Gl switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour Concealed PVC Light point / fan point (for electronic regulator) (6 points /Coil) Higher End

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb

Supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 24W LED square type surface fitting with LED (Higher end) with 1.5 sq.mm PVC unsheathed FRLS copper leads from terminals to the fitting

Supply and fixing of 4 Feet LED 20W Fitting with LED 20W tube (Higher End) complete with TW round blocks on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting

Supply, and fixing of 100 W LED Highway Light with all necessary accesseries in ceiling with connections complete.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. Gl pipe (class B) with 1 no.32 mm dia Gl bend complete on the existing post/on wall with PVC unsheathed FRLS copper leads with MS clamps and with painting.

Supply and run of 1.5 sq.mm PVC insulated SC unsheated FRLS copper conductor of 1100V grade in existing concealed PVC pipe with necessary connection complete.

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 300mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Supply and fixing of 3nos.6A two module 3 pin socket 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (G1) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End

Supply and fixing of 20A Flush type Wall Socket 32A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug)

Supply and fixing of 32A 10kADP MCB in sheet steal enclosuer in flush with wall and making good of the concealed portion with earth connection. (The MCB and metal enclouser shoud be of Higher End)

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour

Supply and fixing of 3nos.6A two module socket, 1 no. 6/16A two module socket 3 nos. 6A one module switch, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End.

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door ( metal) with 1 no. 32A DP MCB as incoming and 10nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of 32A FP MCB in sheet enclosure in flush with wall and making good of the concealed portion with earth connection. (The MCB and metal enclosure should be of Higher End.

Supply and fixing of 4 way 7 segment triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP42 Protection with 25A 4 pole MCB as incoming and 3 Nos. 25A DP RCCB with 30mA sensitivity as sub incomes and 12nos. 6A to 20A SP MCB an outgoing in flush with wall and making good of the concealed portion with earth connection. (Higher end)

Supply and run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 Nos 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed portion

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCB switch as incoming and 2 Nos 63A TP MCB 2 nos 32A TP MCB and 12Nos 32 SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and Run of 4 of 25 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 16sq.mm copper wire and making good of the concealed portion.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and run of No-8 SWG Copper wire in suitable PVC rigid pipe on wall / floor /ground for earth connection.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps /supports on wall / floor / ground for earth connection.

Design, Engineering, supply, fabrication. Erection, Testing commissioning and with handing over of 1 No 15 Persons Stretcher-cum-Passenger Lift with speed 1m/s with M/C room with stainless steel panels, disable friendly, microperocessor board controller, VVVF drive, Fire rated doors and ARD as per the following Technical specifications. as per the swer the S following Technical Specification. (GEARLESS LIFT WITH MACHINE ROOM) 1.Type of Lift: Stretcher cum Passenger Lift 2. Capacity of Lift: 15 Persons/1020Kgs 3. Speed: 1.00 Meter/Sec 4. Type of Drive: specific Variable Voltage 5. No. of Floors : (Ground Floor + 3 upper floor) 6. Total Travel: 10.8 mtr approximately 7. Levelling Accuracy: High Level Accuracy with Smooth and jerk free

8. Construction of Car: High quality and suitable thickness S.S. car and M.S false ceiling. 9. Position of Machine: Directly above the 10. No. of Landing Entrance: 4 (Ground +3) 11. No. of car Entrance: One in Front only. 12. Car Entrance Door: Power Operated V3F drive side Opening Sliding S.S Doors with VF operation.

13. Landing Entrance Door: Power Operated V3F driver Side Opening S.S Doors with provision emergency key opening at all Landings. 14. Lift Well Existing: 2400 mm (width) X 3000 mm (depth). 15. Lift Pit Depth required: 1600 mm 16. Car Size: as per standards upto date 17. Car Clear Opening: as per standards upto date. 18. Power Supply: 400/440 V, 3 Phase, 50Cycles / Sec AC supply for power and 230V 50HZ single phase AC Supply for light at machine room with proper two distinct earth flat of adequate size from ISI earthing at ground floor.

19. Control: (Microprocessor) Microcomputer based Simplex, Collective control with or without attendant 20. Car Fittings: Compact LED Lighting with 2 Nos. 300 mm Sweep Cabin Fan. 21. Lift Well: R.C.C Construction with Brick Masonry. 22. Indication: UP/DOWN Digital Direction and position indicator for all landing and inside the car. 23. Emergency Alarm Bell: Battery Operated alarm bell with Automatic Charging Device.

24. Emergency Light: Battery operated Light with Automatic Charging Device. 25. Fire Man's Switch: Include at Ground Floor. 26. Scaffolding: Included. 27. M.S. Sill angels and facis Plates: Included 28. Steel for Lift Machinery: Included 29. Servicing and maintenance: Free comprehensive servicing and maintenance during the guarantee period of one year.

30.Automatic Rescue Device: To facilitate the landing of the lift to the nearest floor at the time of Power Failure. This shall consists of suitable type of Battery system with charger, invertor, under Voltage Protection system etc., Complete with all Accessories.

31. Provision of Intercom with phone: Included 32. Lift Licence: Preparation of Drawing, payment of Charges to CEIG / Lift inspectorate and insurance policies if any and obtaining CEIG safety certificate as per Lift Act. 33. Floor Annunciator with music: Included.

34. SPECIAL FEATURE: A.) Infra-Red colour Sensor with Height Screen. B.) Stainless steel signal fixtures. C.) Vandal Proof Button with S.S Cover. D.) S.S door frames for landing doors. E.) VF Door operator. F.) Calls register Signal. G.) Stainless Steel Facia plate for car operating Panel and landing fixtures. H.) ON-OFF Switch for fan and Light. 1.) Voice Annunciator.

35. Lift Duty motor of adequate capacity electromagnetic brake with compression springs, over speed Governor, Phase failure and phase reversal relay, alarm Bell, T Guide Brackets for car and Counter weight, Rubber padding under winding unit, car safety Gears, Buffer, Electro Mechanical Door Locks, Emergency Key. Side supporting angles motor Over Load Protection Devices. Final limit Switch, main suspension ropes, Counter weights, Lifting Joist for Mounting the Machineries. 36. Site testing in accordance with IS 14665 or asper standard upto date should be carried out at the time of handing over.

Supply and installation, testing and commissioning of 58.5 KVA WATER COOLED Diesel Generator set with acoustic enclosure conforming to CPCB IV+ norms and BIS specifications with AMF panel as per Technical specifications

A) DIESEL ENGINE:- Diesel engine Model liquid cooled, turbocharged with after cooler, developing 74HP @ 1500 RPM. is Three cylinders in line, electric start, compression ignition, 4 stroke, designed to run continuously at 1500 RPM confirming to IS 10002, ISO-3046, BS 5514 standard. Diesel Engine will comply with present CPCB-VI+ norms. The diesel engine will comprise of following

1. Dry type air cleaner 2. Exhaust Silencer suitable for canopy 3. Expansion bellow 4. Lube Oil cooler 5. Lube oil filter 6. Fuel Filters 7. Radiator with pusher type fan and

8. In-line mono block fuel injection pump 9 Electronic governor and fuel feed pump 10. Flywheel with starter ring and bell housing suitable for close coupling 11. 24 Volt electric starter motor 12. Battery charging alternatof 13. Microprocessor based Controller mounted on the Controller KG745 14. Protection System for Low lube oil pressure High water temperature

B) 12/24 Volt Electronic starting Equipment: Complete with starter motor, dynamo, standard batteries with cable, flexible exhaust piping of 50cms length

(C) Engine Instrument Panel / Mounted: Starting push botton / starting key, lubricating oil, temperature gauge, lubricating oil pressure gauge, water temperature gauge, safety control for low lubricating oil, pressure, safety control for high water temperature, safety control for over speed, hour meter (mechnical) and RPM indicator, battery charging ammeter. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous at full load.

D) ALTERNATOR:- 58.5kVA Alternator, suitable for continuous operation rated at 1500 rpm 415 V, 0.8 PF, 50Hz, 3Ph. in SPDP enclosure, self-excited & self-regulated, Brush less, floor mounted with Ball or Bearings on end shields. The alternator conforms to IS: 4722, BS EN 60034-1& will be suitable for tropical condition. With ASAS provision

E) BASE FRAME:- Suitable to couple above Engine & Alternator made from steel sheet metal.

F) FUEL TANK:- 165 Liters Capacity, with Inlet & Outlet arrangement, air vent & drain plug arrangement

G) BATTERIES:- 12 Volts Battery with one set of connecting leads of Copper Cable

H). Exhaust Gas Recirculation system arrangements as per CPCB IV+ norms as amended

(I) AMF CONTROL PANEL: The AMF control panel (cubical) should be fabricated with vermin proof and dust proof best quality sheet steel and floor mounted with removable rear panels and hinged front doors with enamel painted and incorporating the following with suitable provision for connection incoming and outgoing leads having been made on the control panel.

8. 1 set Air break contactor with auxiliary netural contactor for main supply 9. 1 set Low volage HRC fuse for the short circuit protection of the main supply 10. 1 set Alternator contactor with auxiliary netural contactor

11. 1 set Three pole bimetal release for over load protection of alternator 12. 1 set low voltage HRC fuse for the short circuit protection of the alternator 13.1 set DC control relays incorporating engine start/stop and failure to start /lockout

19. 1 no signal lamp for indicating load on set 20.1no signal lamp for indicating set fails 21.1no signal lamp for indicating set running 22.1No signal lamp for indicating battery 23. 1set Pilot lamps of 3 nos

24. MCCB of 100A capacity with magnetic thermal overload release, instant start circuit trip and under voltage release switch 25.Rectangular copper bus bars (1No for each phase, neutral and earthing terminals) of adequate capacity duly colour coded with head shrinkable PVC sleeves.

26.1No mains voltage monitor 27.Hooter/Audio alarm for indicating set fails to start and for DG O/L. 28.1set Timers

29.Audio and Visual indicator arrangements for: a) Low lubricating oil pressure b) High water temperature c) Over speed 30.1No Earth fault relay

31.Isolator to isolate the neutral 1. The control panel should be complete with necessary fuses, cables, label, other accessories with neutral isolation arrangements.

2. The engine should trip for the following: a) Low lubricating oil pressure b) High water temperature (c) Over speed

3.Supply and fitment of Auto Mains Failure Panel, 1 EB Service wih Suitable Amps switch and contactors SUF Control relays, timers etc suitable for auto change over of DG & EB Service.

J)CANOPY The Genset is Positioned Integrally inside the ARAI approved TYPE TESTED Canopy as per the norms for emission and noise pollution implemented by the Central Pollution Control Board(CPCB), which is effective from 01.01.2005.

K.Auto Start Auto Stop Panel : Line Voltage Monitoring (LVM) TECHNICAL ACOUSTIC CONSTRUCTION SPECIFICATION OF ENCLOSURE Following are some technical features of Acoustic Enclosure:-

1. The enclosure is modular in construction 2. Base frame is made of Sheet metal 3. Durable industrial locking system is provided on doors. 4.Doors are gasket with high quality EDPN material.

CORROSION RESISTANCE:- To make the enclosure weather proof: - 1. All sheet metal parts/components are hot dipped in seven tanks process, pretreated and passivated. 2. Sheet metal components are painted with P.P base power. 3.Base frame is epoxy coated. 4. Zinc passivated hardware is used to avoid rusting

ACOUSTIC INSULATION:- 1. Sound proofing of the enclosure done with quality Foam confirming to IS: 8183. 2. Acoustic form shall be fire retarded and fire resistant.

3. Attenuates are provided to control sound at entry and exit to and from the 4. Specially designed Residential Silencer is provided.

ELECTRICAL:- Neutral earth connecting point at termination block / neutral bus at control panel & Body earthing points at alternator leg and acoustic enclosure base frame.

SOUND LEVEL:- The Genset being offered comply to a sound level of < 75 dbA (12 point average) at a distance of 1-meter in free field conditions conforming to CPCB Norm

WARRANTY:- The warranty is for 24 months from commissioning or 5000 hours of operation whichever is earlier, subject to use.

L)Erection of generator set with proper alignment over the existing foundation.

M)Supply of manuals for operation & maintenance of DG set with warranty card etc.

N) CEIG approval: Preparation of site plan physical layout, electrical line schematic Diagram 10 sets, getting drawing approval from CEIG preparation of complection report rectification report etc., arranging CEIG inspection and obtaining CEIG safety certificate, payment of CEIG inspection fees if necessary and preparation of one set of approval Drawing and copy of safety certificate in a neat frame work.

O)TESTING AND COMMISSIONING After the installation of DG set on its foundation, the DG set should be tested and commissioned with first charging of lubrication oil to its level, first charging of battery and run the set for eight hours on full load test complete. The Genset engine and alternator make should be approved by department officials before used on work.

Supply and fixing of Exhaust Pipe with Silencer for 58.5 KVA Genset.

Providing suitable concrete foundation with plain cement concrete 1: 2: 4 using 20mm jelly for wearing coat including laying compacting finishing and curing etc. complete as per standard specifications and an directed by departmental officers suitable for 58.5 kVA Genset .

Supply and Laying of 3 1/2 x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 3-1/2 x 70 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and providing cable end termination of 3-1/2 x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 70 sq.mm. PVC armoured LTUG cable with earth connection

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box on wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 5 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with suitable Module GI switch box on wall with 1 no. 6A one way module switch and 1 no. 6A 3 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Plug point ( 8 points / Coil) Higher End

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with IP 42 protech in with 1 no. 32A DP MCB as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only.Higher End

Supply and fixing of 63A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with Earth connection only.

Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3-1/2 x 35 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC aluminium armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Design, Supply, Installation, Testing of 400A, 3L+N, Sandwich type Aluminium Bus Bar Trunking system, Straight run feeder (Rising Main)Indoor IP55 protected, insulation class F (155° Dust and Vermin proof made up of Galvanised iron, with provisions for Aluminium Earthing Plug in points at every floor necessary angle iron supporting etc. Reference standard: IEC 61439-6. Reference temperature: 40 °C, Protection degree: IP55. Thickness: 1.6 mm, No of conductors: 4. Painted: RAL 7032 Halogen Free, The insulation between bars is ensured by a multi sheath made with PET film class F(155°C) Complete with Aluminium busbar Flexible with provision for rotary handle mechanism with bottom Cable entry and top Busduct outgoing provision and connections complete.

Supply and Fixing of Tap Boxes 250A 25KA FP MCCB with suitable enclosure and Acessories and earth connection complete

Supply and Fixing of Tap Boxes 100A 25KA FP MCCB with suitable enclosure and Acessories and earth connection complete

Supply and Installation of 400A Flange End for raising mains with necessary accessories and connections complete

Supply and Laying of 25x6mm Aluminimum Earth Flat with necessary clamps/supports for earth connection.

Supply and Fixing of MS Supports for with necessary accessories for fixing Rising Main

Supply and clarnping of 3-1/2 x 150 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps..

Supply and fixing of brass cable gland for 31/2 x 150 sq.mm PVC LTUG armoured cable with earth connection.

Supply and providing cable end termination of 3 1/2 x 150 sqmm PVC LTUG Aluminium armoured cable withnecessary aluminium cable sockets by crimping etc. with electrical connection complete

Supply and fixing of dust and vermin proof cubical type LTCT metering box of size 3ft x 1 ft x 4ft made of 16SWG CRCA sheet steel with door, lock and key arrangement with angle iron support comprising of three compartments for 3 phase energy meter with base plate & view glass arrangements, bus bar arrangements with 1 1/4" x 1/4" insulated tinned Copper bus bar for 3phases & neutral with provision for CTs and sealing arrangements as per TANGEDCO norms and 3nos 315A (500V) fuse units and MS cable entry box. The earth bus with two runs of 1" x 1/4" tinned copper flat must be run all round the panel to provide double earth connection.

The buses should be mounted on the SMC bus insulators with proper spacing and should be provided with heat shrinkable sleeves using RYB & Black colours. The bus bar chamber should be segregated from the adjacent chambers by providing 12mm thick hylem, sheet. The panel should be Powder coated the cable size, location etc., should be marked with white paint affixed with Danger sign with 19/16 PVC insulated Cu wire interconnection from meter to fuse unit and necessary connection complete confirming . CEA regulations.

Supply, fabrication, erection and commissioning of 315A dust and vermin proof floor mounting cubical type panel board of suitable size 5ft x 5ft x 1 ft made up of 16 SWG CRCA sheet steel for outer body and stiffness and doors, switch supports respectively and supply and fixing of following interior mounting switches with centre bus bar chamber of 1 1/4" x1/4" tinned Cu.flot for 3phases,neutral and earth bus and Vertical covers on both sides of the bus bar chamber at the extreme ends side and confirming to CEA regulations. All the main switches should be L&T / Siemens make only.

(1) 315A FP Switch Disconnector Fuse Units interior only with HRC Fuses Double Break as incomer 1 No (L&T/Siemens) 11/4"x1/4" tinned Cu.flat for interconnections with bus (2) 250A TPN Switch Disconnector Fuse Units interior only with HRC Fuses Double Break as outgoing 2 Nos (L&T/Siemens) 1"x1/4" tinned Cu.flat for interconnections with bus

3) 100A TPN Switch Disconnector Fuse Units interior only with HRC Fuses Double Break as outgoing 2 Nos (L&T/Siemens) 1"x1/8" tinned Cu.flat for interconnections with bus (4) 63A TPN Switch Disconnector Fuse Units interior only with HRC Fuses Double Break as outgoing 4 Nos (L&T/Siemens)3/4"x1/8" tinned Cu.flat for interconnections with bus

A separate chamber on top of one side should be built with multi function digital volt meter, ammeter and frequency meter with one set of LED pilot lamp set with fuse base, top with 10A HRC link for 3 phase (Siemns) the bus will have 2 Nos 11/4"x1/4" earth bus must be run all around the panel to provide double earth connection to the cubical switches cable glands, cable adopter box etc.

the bus should be mounted on synthetic moulded compound bus support at equal interval as per CEA regulations. The switch should be separated from the bus by 6mm thick hylum sheet separators, and properly earthed by tinned solid copper flat as per CEA regulations. The panel should be Powder coated , the cable size, capacity of switch, location etc., should be marked with white paint and 2 Nos. metallic danger board affixed complete with mounting on base channel 3"x1"x½" iron frame work support complete.

Supply and fixing of 315 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only

Supply and clarnping of 3 1/2 x 240 sq.mm. PVC armoured LTUG cable LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 240 sq.mm. PVC aluminium armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3-1/2 x 240 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of 300mm x 50mm 16SWG GI Hot dip galvanized powder coated preforated cable tray on ceiling or wall with necessary fastereners, bolt nuts and clamps. and necessary connection complete (Higher end)

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal/ acrylic door cover flush type /surface type fitted with busbars and neutral links with single /three phase MCB outgoings and seperate 4 way provision for accomodating one No 4 pole incoming MCB/Isolator and another seperate 4 way provision for accomodating one No 4 pole ELCB /RCD (totally 8 ways in one segment) (3x 4 ways in Each segment) and seperate provision for MCB /Isolators (totally 12 Nos) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with Earth connection only.63A 4P MCB-1 No, 63A 4P 30MA RCCB/ELCB -1 No, 63A DP MCB Isolator -3 Nos, 6A to 32A SP MCB-12 Nos

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCB as incoming and 2nos. 63A TP MCB, 6no 6A-32A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. Higher End

Supply and fixing of single box type 4' 20W LED fitting with CRCA body complete with TW round blocks with conduit pipe suspension with 20W LED tube with PVC unsheathed FRLS Copper leads from terminals to the fitting. (Higher End)

Supply and fixing of 400mm (16") sweep wall mounting fan complete on wall with connections complete.

Supply and fixing of 63A, 10kA FP MCB in sheet enclosure in flush with wall and making good of the concealed portion with necessary earth connection. (The MCB and metal enclosure should be of Higher End).

Supply and fixing of 4way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A FPMCB switch as incoming ond 4Nos. 32A TP MCB as outgoing in flush with wall with earth connection only. Higher end

Supply and fixing of 65mm (2½") Class B Gl pipe of 5 mtr length with 300mm x 300 mm x 6 mm MS base plate duly welded at the bottom with concreting and mansory pedastal with necessary connection complete.

Please Enable Macros to View BoQ information