Construction 1 No fully furnished conference room adjoining the Chief Engineer Beas Dam office at Talwara township

Amount

Dismantling brick work constructed in cement mortar [CSR item No. 8.5(b)]

Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2 Mtr. Depth including dressing of bottom and sides of trenches stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm layer with compaction including disposal of all surplus soil as directed within lead of 30 Mtr.(CSR item No 6.6)

Earth filling under floors with surplus soil containing more than 40% gravel or kankar excavated from foundation and taken only from outside the building plinth in 15 cm layers including ramming, watering and consolidating lead upto 30 meters (CSR item No 6.8 (ii) )

Cement concrete 1:5:10 with stone ballast 40mm gauge using concrete mixer volumetric type [CSR item No 10.9 (b)

Cement Concrete 1:4:8 with stone ballast of size 20mm gauge [CSR item No.10.11 (ii)

Reinforced cement concrete M-20 (1:1½:3) mechanically batch mixed using batch type Concrete mixture as per IS : 1791 and vibrated by needle vibrated but including steel reinforcement centering and shuttering in foundation and plinth [CSR item No.10.15 & A&C-1 -2020

First class burnt brick work laid in cement sand mortar 1:6 in foundation and plinth. [CSR item No. 11.3(i)

Damp proof course 4 cm thick of cement concrete 1:2:4 with two coats of bitumen 20/30 penetration @ 1.65 kg per sqm laid hot and sanded. [CSR item No. 10.26]

First class burnt brick work laid in cement sand mortar 1:6 in first storey up to 4 meter above plinth level. [CSR item No. 11.4(i)]

First class burnt brick work laid in cement sand mortor 1:4 in first storey upto 4 metres above plinth level [CSR item No. 11.8(i)]

Providing, lowering in trenches to correct gradient and alignment, jointing with tyton rubber joint and cutting of reinforced cement concrete spigot and socketed pipes and specials with rubber ring ISI marekd as per IS code IS 458-2003 into trenches for all depths and laying out the same to correct alignment, gradients, levels etc. cutting of concrete beds and joints holes, supporting the pipes and specials in correct position in a suitable rigid manner while the same are being jointed and until the surrounding benchings, haunches and envelopes are completed. The pipes shall rest on the beds at all joints through their lengths and fixing of rubber ring, facing, testing the pipes for leakage and making good the same leakage and all defects to the entire satisfaction of the Engineer-in-charge including all cartage etc.R.C.C. Pipe P -1 (150mm i/d pipe(CSR Item No. 29.46 (A)-b

Cement concrete 1:2:4 with stone ballast or shingle using concrete mixer volumetric type. (CSR Item No. 10.13 a (ii) A & C-1 -2020

Reinforced cement concrete M-20 mechanically batch mixed using batch mixed using batch type conc. Mixer as per IS : 1791 & viberated by needle viberator but excluding steel reinforcement centering and shuttering in superstructure [CSR item No.10.20. A & C-1 -2020

shuttering for faces of concrete foundations and foundation beam and plinth beam ( vertical or battering) [CSR item No. 9.1]

Centering and shuttering for columns (Square or rectangular or polygonal in plain [CSR item No. 9.4]

Cantering and shuttering for flat surfaces such as suspended floors , roofs landings , chajjas shelves etc.[CSR item No. 9.8 )

Centring and shuttering for sides and soffits of beam, beams aunchings girders bressumers, lintels [CSR item No. 9.6]

Cold twisted deformed ( ribbed/ tor steel ) bars Fe 500 grade as per IS : 1786-1985 for RCC works where not included in the complete rate of RCC including bending binding and placing in position complete [CSR item No. 18.18]

Terracing consisting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg. /Sqm top of R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing etc.[CSR item No. 13.13 (i)

12.5mm thick cement plaster 1:5 [CSR item 15.10]

Plastering on underside of ceiling 10 mm thick cement plaster 1:4 [CSR item 15.44]

Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge 15 mm wide and 15 mm deep groove [CSR item 15.71]

Top khurra 0.6m x0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16.[CSR item No. 13.45]

Bottom Khurra on ground 1.2m x0.6m consisting of brick on-edge laid in cement mortar 1:3 over 75mm cement concrete 1:8:16 including 12.5mm thick cement plaster 1:3 [CSR item No. 13.51]

Cement concrete 1:2:4 gola 10cm x 10 cm concave quadrant along junction of roofs with parapet wall finished smooth where specially specified. [CSR item No. 13.55]

Providing and fixing 110 mm dia . U.P.V.C Rain water pipe of 2.5 kgf./sqm as per IS:4985 including jointing during masonry complete as per specifications and to the entire satisfaction of Engineer-in- charge. (If fixed on wall face clamp to be paid separately as per respective item) [CSR item No. 13.74]

[Providing and fixing 110 mm dia SWR U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge.CSR item No. 13.75 (a)

Providing and fixing 110 mm dia SWR U.P.V.C Coupling/Socket for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. [CSR item No. 13.76 (a)]

Floating coat of 1.5mm thick neat cement laid in one operation to the topping. . [CSR item No. 14.4]

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish [CSR item No. 16.65]

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two coats over one priming coat to give an even shade.[CSR item No. 16.10] A & C-1 -2020

Finishing walls with acrylic smooth exterior paint of required shade with two coats applied @ 1.67 litre/10sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 sqm[CSR item No. 16.59] A & C-1 -2020

Providing and laying vitrified floor tiles (600X600) in different sizes in light colour shades made using Soluble Salt Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Soluble salt Print Penetration should be up to 1 to 2 mm after the tiles are fired & polished ). CSR Item No. 14.112 (a)

Providing and laying Rectified Porcelain floor tiles 400x400mm or more (thickness to be specified by the manufacturer) of premium quality conforming to IS:15622 of approved make in all colours laid on 20mm thick bed of Cement Mortar 1:4 ( 1 Cement : 4 Fine sand) for new flooring or laid with cement based high polymer modified quick set tile adhesive (water based) of approved make IS 15477 marked using 5 Kg adhesive per Sqm of tile area in average 3mm thickness over existing floor, including pointing the joints with white cement and matching pigments etc., complete(CSR Item No. 14.123)

Providing and laying 50 mm thick factory made cement concrete interlocking paver block of M-30 grade machine made rubber moulded smooth finish with strong vibratory process or with vibro- hydraulic compaction machine and of approved size and design / shape laid in Ordinary Grey and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge IS Code 15668(2006) (CSR Item No. 14.136 & A&C-2.

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/ Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 450 x 310 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. ( CSR item No. 14.127)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is:733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, metered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and panelling to be paid for separately) :[CSR item 17.45]

(a) For fixed portion and chawkhats [CSR item 17.45(a)] [email protected]/Sqm

(b) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required. CSR item 17.45(b)][email protected]/Sqm

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece MS sheet outer box with slide plate and with stainless steel cover plate etc. complete as per the direction of Engineer-in-charge[CSR item 17.48]

Providing and fixing aluminium sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :[CSR item 17.49(a)] 300mm x 16mm

Cost of Aluminium fittings complete for doors, windows such as tower bolts, handless and screw etc. for these fittings (Excluding sliding bolt) :[CSR item 17.23(ii)] For shutter area above 0.50 sqm

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete [CSR item 17.43]

I.S.I Designation No. II (size of door 701mm to 850mm) [CSR item 17.43] (b

I.S.I Designation No. III (size of door 851mm to 1000mm) [CSR item 17.43c)

Providing and fixing 22/12 SS wire mesh (AOR attach )

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.:[CSR item 17.46(ii)]

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item) :[CSR item 17.47(i)] Float glass panes of 5 mm thickness.

Supplying Pressed steel sheet frames (chowkhat) consisting of 18gauge (1.25 mm thick steel sheet of the specified section, including iron lugs (hold fast) iron hinges conforming to PWD specification including bolts for fixing stops lock notch provision for receiving tower bolts and finished with 1 primer coat approved quality, fixed in position excluding the cost of cement concrete 1:3:6 for fillings in the frame and cement concrete 1:2:4 for lugs complete ( CSR 18.24 )

Doors and windows frame of size 113mm x 60mm with 35 mm wide single rebate weighing 3.38 kg per meter.

Doors and windows frame of size 151mm x 60mm with 35 mm wide double rebate weighing 3.95 kg per

Cutting Chase in brick walls in cement or in floor for embedding G.I or C.I pipes line and making good the same to its original condition Size 75x75 mm.(CSR item No. 30.85 (a))

Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) B Class including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete. (CSR 28.35 (a)

Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) B Class including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete. (CSR 28.35 (b)

Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) B.Class including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete. (CSR 28.35 (c)

Providing, fixing & jointing ISI Marked Gun metal peet valves( heavy pattern) as per IS 778 with hand wheels, on GI pipe lines laid in the ground or inside buildings including all carriage complete (a) 15mm i/d Gun Metal peet valve heavy pattern. [CSR item No.28.43(a)]

Providing, fixing & jointing ISI Marked Gun metal peet valves( heavy pattern) as per IS 778 with hand wheels, on GI pipe lines laid in the ground or inside buildings including all carriage complete (b) 20mm i/d Gun Metal peet valve heavy pattern. [CSR item No.28.43(b)]

Providing, fixing and jointing G.I. Union couplings (of approved make with the approval EIC) as per IS 1879 in G.I. pipe lines complete in all respect. 15mm i/d G.I. Union [CSR item No. 28.40(a)]

Providing, fixing and jointing G.I. Union couplings (of approved make with the approval EIC) as per IS 1879 in G.I. pipe lines complete in all respect. 15mm i/d G.I. Union [CSR item No. 28.40 20mm i/d G.I. Union[CSR item No. 28.40(b)]

Providing and fixing in position single socket SWR UPVC soil waste vent or antisyphonage pipes as per IS- 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing wastage, but excluding cost of jointing. Single socket Type B 160 mm o/d SWR UPVC pipe Line laid complete [CSR item No.30.74 iii (B) (a)]

Providing and fixing in position single socket SWR UPVC soil waste vent or antisyphonage pipes as per IS- 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing wastage, but excluding cost of jointing. Single socket Type B 110 mm o/d SWR UPVC pipe Line laid complete [CSR item No.30.74 iii (B) (b)]

Providing and fixing in position SWR UPVC specials for soil waste vent or antisyphonage pipes as per IS- 14735 including cutting, jointing wastage etc. Cutting holes in walls roofs or floors etc. And making good to its original condition but excluding cost of lead jointing. B For 110mm o/d pipes P Trap or Floor Trap110 mm x 110 mm [CSR item No.30.81iii B (ix)]

Providing and fixing in position SWR UPVC specials for soil waste vent or antisyphonage pipes as per IS- 14735 of approved make ( to the approval of Engineer in charge) including cutting, and wastage etc. Cutting holes in walls roofs or floors etc. And making good to its original condition but excluding cost of lead jointing. B For 110mm o/d pipes elbow 90 degree( all side socketed) [CSR item No.30.81iii B (v)]

Providing and fixing in position SWR UPVC specials for soil waste vent or antisyphonage pipes as per IS- 14735 of approved make ( To the approval of Engineer in charge) including cutting, jointing wastage etc. Cutting holes in walls roofs or floors etc. And making good to its original condition but excluding cost of lead jointing. B For 110mm o/d pipes vent Cowl [CSR item No.30.81 iii B (vi)]

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm.(a) 100 mm internal Diameter S.W gully Trap with H.C.I grating and cast iron cover weighing approximately 7.26 Kg. And frame clear opening 300 x 300 mm and out of side size 330 x 330mm.[CSR item No.30.99 (a)]

Providing and fixing in position Chinaware extended wall mounted E. W.C. type suite (size 66 x 46 x 77.5 cm ) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) with or without 10 ltr. chinaware matching flushing cistern and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge. (CSR-30.5 b)

Providing and fixing in position concealed cistern including flushing plate of approved make (to the approval of the Engineer-incharge) complete in all respect. .(CSR-30.6c)

Providing and fixing stainless steel Health faucet complete in all respect. (CSR- 30.24)

Providing and fixing in position vitreous Chinaware white Senso urinal size 37 x 39 x 61 cm of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass Urinal waste Coupling dome type 32mm outer length 75 mm complete in all respect.(CSR-30.17A)

Providing and fixing partition for different type of urinals 19 to 20 mm thick Granite stone partition size 375mmx750mm. [CSR-30.21(A)ii ]

Providing and fixing in position vitreous chinaware white channel of approved make (to the approval of Engineer –in-charge) of size 600 x 100 mm including laying and fixing in cement concrete 1:2:4 complete in all respect. (CSR-30.100)

Providing and fixing in position vitreous chinaware with lavatory suites of approved make (to the approval of Engineer –in-charge) consisting of C.P brass waste 32mm dia with one C.P brass pillar tap including Rack bolt screw pair 115mm long complete in all respect. (CSR-30.32(ii)) Size 550mmx400mmx 815mm

Providing and fixing in position CP Brass single lever surgical mixer with swinging spout approved make (to the approval of Engineer-in-charge) complete in all respect.(CSR Item No. 30.40

Providing and fixing in position vitreous chinaware s pedestal of approved make (to the approval of Engineer –in-charge) for wash hand basin complete in all respect. (CSR-30.43(i)) Viterous chinaware standard white pedestal for wash hand basin

Providing and fixing in position C.P brass bottle trap 32mm dia with 40mm seal of approved make (to the approval of Engineer –in-charge) complete in all respect. (CSR-30.44)

Providing and fixing in position stop cock/Angle valve of approved make (to the approval of Engineer-in-charge) complete in all respect C.P brass15mm angle valve without flange. (CSR item No. 30.66 (c))

Providing and fixing in position 15 mm CP brass auto close bib cock of approved make (to the approval of Engineer-in-charge) (CSR-30.35)

Providing and fixing in position 5mm thick beveled edge mirror of superior glass(of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P brass screws and washers and S/S studs on top complete in all respect (as required by the Engineer-in-charge) Size 600mmx450mm (CSR-30.61a)

Providing and fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge) complete in all respect PVC tube connection of size 15mm x 450mm with C.P Brass nut. (CSR-30.72 b)

Providing and fixing in position S.S. grating with frame of approved make (to the approval of Engineer-in-charge) complete in all respect. ( CSR-30.80)

Providing and fixing in position storage type automatic electric water heater pressure/ non-pressure type thermostatically controlled, single phase vertical wall mount of approved make (to the approval of Engineer-in-charge) with thermostats, inner container of stainless steel complete with 1 Mtr three core flexible cord with plug non-return valve and pressure release valve complete including fixing and testing complete in all respect (CSR-30.101 (a)) 25 Ltr capacity water Heater.

Providing and fixing in position paper holders of approved make (to the approval of Engineer-in-charge) fixed in wall with C.P brass screws complete in all respect. (CSR-30.57a) C.P brass Toilet Paper holder

Providing and fixing in position towel rails/ring of approved make (to the approval of Engineer-in-charge) fixed in with rawl plugs embedded in walls with brass screws complete in all respect. (CSR-30.58) a C.P brass towel rails size 15mm dia 610mm long.

Providing and fixing in position towel rails/ring of approved make (to the approval of Engineer-in-charge) fixed in with rawl plugs embedded in walls with brass screws complete in all respect. [(CSR-30.58) b] C.P brass towel ring

Providing and fixing in position C.P Acrylic shelf with C.P bracket and guard rails of approved make (to the approval of Engineer-in-charge) fixed in with rawl plugs and CP brass screws complete in all respect. (CSR-30.59)(a) C.P brass Acrylic shelf size 560mm x 130mm

Providing and fixing in position C.P brass soap dish of approved make (to the approval of Engineer-in-charge) fixed into with brass screws complete in all respect. (CSR-30.60)

Providing and fixing in position G.M Non return valve 20mm ( Quotation Attached)

Providing and placing in position on terrace ( at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer-in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. (CSR-30.97A (i)) Triple Layer Tanks

Providing and fixing in position G.I tank Nipple of approved make (to the approval of Engineer-in-charge) complete in all respect. G.I tank nipple 20 mm i/d (CSR-30.98(b))

Providing and fixing in position automatic brass ball cock in Tanks. brass ball cock with rod and plastic ball 20mm i/d (CSR-30.96 B) (ii)]

Providing & fixing of non reflective 8mm th.Toughened Glass board (white back Pinted) fixing with adhesive with duster set.(Quotation attached) with GST 18%

Laminated Plywood Paneling (12mm Thk.), Providing & fixing Wall paneling to consist of 12 mm th plywood finished with 1mm Laminate with required frame work with teakwood beading patty or 12 mm plywood backing grove pattern at wall surfaces,Window sill, Partition edge as per required & suggested Area.(Quotation attached) with GST 18%

Providing & applying 3 coats of 1st quality Tractor Emulsion of approved shade with two coats of putty, two coats of approved primer, and three coats of approved plastic paint, including preparation of surface, scrapping, sand papering, scaffolding, all materials and labour, taxes etc complete. as approved by Engg.-in-Charge/ Designer Putty should be of asian, Paint should be Low Volatile Organic Compound level as per standered Applicable (24.14 to 55.62 Gr/Ltr) done as per directed by engineer in charge. (Quotation attached) with GST 18%

Providing & fixing of suspended ceiling, which includes Gypsteel ultra CRPsurface ribbed perimeter channels of size 0.55 mm thk. (having one flange of 20mm & another flange of 30mm and a web of 27mm ) along with perimeter of ceiling, screw fixed to brick wall /partition with the help of nylon sleeves and screws, at 610mm centres then suspending Gypsteel Ultra CRP surface ribbed intermidiate channels of size 45 mm (0.9 mm th with two flange of 15mm each) from the soffit at 1220mm centres with gypsteel ultra CRPsurface ribbed ceiling angle of width 25mm x10mm x 0.55mm thick fixed to soffit with GI cleat and steel expansion fasteners (mfg by Saint Gobain India Gypsum) then Gypsteel ultra ceiling section of 0.55 mm th. having knurled web of 51.5 mm and two flange of 26 mm each with lips of 10.5 mm are then fixed to the Gypsteel ultra intermediate channel with the help of connecting clip and in direction prependicular to the Gypsteel ultra intermediate channel at 457.5 mm centres single layer of 12.5mm tapered edge Gypboard (conforming to is 2095 part 11996) is then screw fixed to ceiling section with 25mm drywall screws at either with screw driver or drilling machine with suitable attachment.(Cost including for suspending Member from rcc ceiling ) Gypsum boards to G.I. framing in perfect level. Necssary offsets and grooves to be povided at the junction of ceiling & Modular ceiling,walls/columns/partitions etc.Cut out for light fittings A/C grills etc.& including providing & fixing necessary G.I./wooden frame supports for the above fixtures & additional suspenders to hang the same independently.(Quotation attached)

Armstrong Ceiling :- Providing and fixing CLASSIC LITE RH 99 (Silhautte grid) 16mm false ceiling system manufactured by Armstrong using hot dipped galvanized steel section, rotary stitched main tee of size 15mm x 45 mm web height, having 0.36 mm gauge at every 600 mm centre to centre maximum and rotary stitched cross tee of size 15 mm x 45 mm, having 0.33 mm gauge at every 600 mm. c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 600mm c/c. in both directions using 2.0 mm. thick pre-straightened GI wire laying CLASSIC LITE RH 99 ceiling tiles with Silhautte grid manufactured by Armstrong , having Humidity Resistance of 99%, RH and size 600mmx600mmx16mm over the formed grid complete. including light fixtures cutting gala in ceiling.(Quotation attached)

Providing & fixing of Perforated Rollar blinds (Vista Aerolux or equilant, with head Rail and fabric connector with minimum gap of 6/8 mm if required as per specified. Panama 5% Gffebric tighter yarn 78 TEX with weighted composition, Glass Fabric 29% , PVC- 71%, Fabric openess factor is 5% with thickness 0.44mm with mass 345g/m2 yarns in warp/weft/cm 26/21, Fire rating is M2 , BS 5867 Colour Fastness minimum 7 (ISO.105B01), The control unit consists of clutch mechanism. The unit is made of high strength reinforced plastic. The clutch is of wrap spring design, high carbon steel springs are provided to transmit motion form the driven mechanism. Clutch is operated directionally by use of endless beaded chain to raise and lower the blind smoothly to decide height.Clutch never needs adjustment. Idler is high strength reinforced plastic, consisting of an outside sleeve and center shaft. Sleev provide bearing surface for center shaft and rotate freely, providing smooth, quiet and long wearing operation. Head rail is an aluminum extruded rail on which control unit and idler are mounted with help of brackets.Bracket for mounting control unit and idler for heavy duty mechanism, brackets are power coated. Operating chain is made of 4.5mm plastic beads moulded on 2.2mm th. Polyster cord. The pitch of the beads is 6mm. The chains drives the sprocket fixed in the end control unit to close and open the blind. The pitch of chain correspondes to the sprocket in perfect match for trouble free operation.

Laminated Flush door Providing & fixing laminated flush door made from 35 mm flush door size as per site condition, with 1 mm thick laminate from both side. & teak wood beading & door frame with mortice type locking system & Shutter to be fixed using 4 nos heavy duty hinges of approved brand & also provided S S handle, with all necessary hardware like door stoper, Sterling make Door closer, etc. Complete as per design (Quotation attached) For Toilets

Laminated Flush door (Double Shutter) Providing & fixing laminated Duble shutter flush door made from 35 mm flush door size as per site condition, with 1 mm thick laminate from both side. & teak wood beading & door frame with mortice type locking system & Shutter to be fixed using 4 nos heavy duty hinges of approved brand & also provided S S handle, with all necessary hardwarelike door stoper, Sterling make Door closer, etc. Complete as per design.(Quotation attached) For Hall

RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES :- Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100 volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- [CSR Item 34.02]

Wiring fan point (With fan box) [CSR Item 34.02 (i) b ]

Wiring light point [CSR Item 34.02 (ii) ]

Wiring call-bell point [CSR Item 34.02 (iii) ]`

Wiring 6Amp. wall socket point [CSR Item 34.02 (iv) ]

Wiring 6Amp. Plug control comprising wall socket point [CSR Item 34.02 (v) ]

Wiring 16/20Amp. power plug control point [CSR Item 34.02 (vi) ]

Wiring light point with double control switches. [CSR Item 34.02 (viii) ]

Wiring for UPS/Raw plug outlets points with three core, 2.5 sqmm FRLS PVC Insulated and PVC sheathed flexible cable with bright annealed electrolytic copper conductor , 1100 volt grade confirming to IS : 694/1990 with latest amendments, in existing Channels/conduit in ceiling/walls/floor including all cable termination accessories. (including body earth for GI boxes). Quotation attached

Wiring for UPS/Raw plug outlets points with three core, 4.0 sqmm FRLS PVC Insulated and PVC sheathed flexible cable with bright annealed electrolytic copper conductor , 1100 volt grade confirming to IS : 694/1990 with latest amendments, in existing Channels/ conduit in ceiling/walls/floor including all cable termination accessories) Earthing of GI Box to be included.(Quotation attach)

CONDUITING FOR TELEPHONE ,COMPUTER & CONDUITING AND WIRING FOR T.V. SYSTEM :-

Providing and fixing in position the following G.I flexible conduits including all fixing accessories on to the modelur furniture .25 mm dia flexible conduit with end couplers Quotation attached

Supply and Laying including numbering / ferruling of wire (8 digit) and the continuity test for each cable of Cat 6 - Telephone / Data cable in existing G. I. Channel Quotation attached

Providing and fixing in position suitable 1.6 mm thick G.I. outlet box for 2 Nos. RJ - 45 for Data outlet including with all fixing accessories as required. Quotation attached

S/I/T/C of EPBAX Box for the termination of Data & Voice cable Quotation attach

PVC INSULATED FR COPPERCONDUCTOR CABLES: Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- [CSR item 34.09 ]

Overall size 4sq.mm (Un-sheathed) [CSR item 34.09 (iv) ]

XLPE INSULATED ARMOURED CABLES (LOOSE): Supply, laying and erection of aluminum conductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:- [CSR item 34.10(B)]

Overall size 16sq.mm (4Core) Armoured (Loose) [CSR item 34.10 (B) (xxxvii)]

PVC, HDPE PIPES & PVC FLEXIBLE PIPES : Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- [CSR item 34.12]

Heavy Gauge PVC Conduit Pipe 25mm dia. (Flushed) [CSR item 34.12 (x) ]

Heavy Gauge PVC Conduit Pipe 32mm dia. (Flushed) [CSR item 34.12 (xi) ]

MINIATURE CIRCUIT BREAKERS/RCBO's/ RCCB's: Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- [CSR item 34.16 (A) ]

MCB Single Pole 6-32amp. (10kA, Curve-C) [CSR item 34.16 (A) (ii) ]

MCB Four Pole 50, 63amp. (10kA, Curve-C) [CSR item 34.16 (A) (xvi) ]

SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB's/ RCBO's/ RCCB's: Supply and erection of sheet metal Double Door distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, colorcoded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:- [CSR item 34.17]

TP&N Horizontal Double Door Distribution Board 12 way each [CSR item 34.17(viii)]

Receiving, storing, handling, assembling fixing in position, testing and commissioning of incandescent light fixtures on ceiling or fully/semi recessed in ceiling complete with all fixing accessories as required. Quotation attached

Supply and fixing of prewired LED type lighting fixtures with all accessories (Similar to Wipro Lighting LM17-411-XXX-57-XX Matrix LED Recess Mounted 2ft x 2ft LED Luminaire with Diffuser) Quotation attached

Supply and fixing of prewired LED type lighting fixtures with all accessories (Similar to Wipro Lighting - Cleanray CRDL11R023HP57 Halo - Recessed mounted LED. Down light) Quotation attached

Conference Table (26 seater) Quotation attached

Chairs (Quotation attached)

Providing and fixing curtains with accessories. required material. (Quotation attached)

Providing and fixing 1.5 ton Hot & cold inverter split AC and misc. required material. (Quotation attached)

Providing and fixing 12” exhaust fan with cable and misc. required material. (Quotation attached)

Providing and fixing 36” Ceiling fan with cable and misc. required material. (Quotation attached)

om namah shivay construction co.

vikram sachdeva