Special Repair / Renovation of Sub Health Centre at Village Jalbhera in District Kurukshetra (Under Health Wellness Centre Scheme) (Excluding EI)

Amount

Dismantling brick work, tile masonry or tile lining & tile tracing. (b) In Cement (HSR 8.5 (b)

Dismantling concrete Reinforced cement concrete with cleaning (HSR 8.6 (e) )

Scraping White & Colour wash (HSR 8.32 (a))

Scraping Cement plaster (HSR 8.32 (c) )

Cement concrete 1:1.5:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel einforcement, but including centring and shuttering, laid in position complete in all respects. (HSR 10.82 +10.95(a).

First class brick work laid in cement sand mortar 1:4 in first storey up to 4 meters above plinth level.(HSR 11.9)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm, laid over 87.50 mm mud filling, on a layer of 25 mm mud plaster and an other layer of mud mortar for laying the tiles including two coats of bitumen laid hot at 1.65 kg per sqm on top of RCC slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Pdg. & fixing Ist quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge etc. (HSR 14.92) (b) 300mm x 450mm

Plastering on walls12 mm thick cement plaster 1:4 (HSR 15.5)

Applying pink primer or aluminum priming coat on wood work including preparation of surface, knotting and stopping etc. (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete urfaces to give an even shadeas. (HSR 16.3)

Painting two coat with synthetic enamal paint in all shades on old wood work metalic or plastered surface. (HSR 16.6)

Distempering with washable oil bound distemper (of approved manufacture ) two coats over one priming coats on new work. (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint (b) 1st quality (HSR 16.79 (b)

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (JK/ Birla make) (HSR 16.81)

Chowkats of commercial hard wood such as hollock, champ, chikassy and chaplash etc.(HSR 17.32 (b)25 mm thick )

Supplying & fixing glass panes with moulding of commercial hard wood such hollock, champ, chikrassy, and chaplash, etc. (c ) 4mm thick (HSR 17.36 (c ))

Supplying & fixing hydraulic door closer, I.S.I. mark with necessary screws etc complete (HSR 17.82 (b). ISI designation No.II (size of door 701mm to 850mm) )

Factory manufactured panelled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other than teak,conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 12 mm thick commercial veneered both sides particle board or plywood of B.W.R. grade, hot-presses, including cost of iron hinges,screws,chocks/cleats,stops, and nails etc., complete,fixed in position (excluding the cost of any fittings,other than specified above,but including labour for fixing the same in position).( HSR 17.91) (b) 35 mm thick (-) note .

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other teak, conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail, and wire gauze of 140G or 120G designation including cost of iron hinges,screws,chocks/cleats,stops nail etc.,complete fixed in position (excluding the cost of any fitings,other than specified above,but including labour for fixing the same in position)- (style and rails of windows shutter shall be 75 mm wide) (ii) 35mm thick (HSR-17.92(ii) ) - Note

Wrought iron and mild steel ladders, framed grills, gratting etc. with ends of bars rivetted or forged framed window guards, barred iron doors, etc., including fixing in position. (HSR 18.10 )

Steel reinforcement TMT bars FE-500 EQR / FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights / depths / storeys / basements etc. Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 18.22 )

Pressed steel sheet frames (chowkats) , consisting of 2 mm thick steel sheet of the specified section, including iron lugs (Holdfast), iron hinges, confirming to PWD specifications, including bolts for fixing stops etc. (HSR 18.34 ) (a) Door and window frame of size 89 mm x 50 mm with 40 mm wide single rebate )

Laying of GI./PVC Pipes and Specials Labour for laying, jointing, fixing & testing G.I. pipe i/d cost of specials (HSR 28.18 (b) (ii) 20mm dia

Providing and fixing in position best Indian make European type water closet suite with concealed 'P or 'S trap with or without vent (as approved by the Engineer-in-charge) and all other necessary fittings as fully described in item no. 30.3 above (Approved make are only Cera & Hindware) (i) White (HSR- 30.6)(i)

EXTRA OVER item nos. 30.1 TO 30.4 AND 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY VITREOUS CHINA HIGH LEVEL CISTERN COMPLETE with internal brass fittings instead of 12.5 litres capacity high level C.I. eistern complete (as approved by the Engineer-in-charge). (HSR 30.8) (i) White

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY C.I. LOW DOWN CISTERN flush bend and all other necessary fittings instead of 12.5 litres capacity high level C.I. flushing cistern with flush pipe complete (as required by the Engineer-in-charge). (HSR 30.9)

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY C.I. LOW DOWN CISTERN flush bend and all other necessary fittings instead of 12.5 litres capacity high level C.I. high level flushing cistern with flush pipe IN WHITE ENAMEL SPRAY PAINT after making smooth the C.I. surface by rubbing, scrapping etc., complete. (HSR 30.10)

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY C.I. LOW LEVEL CISTERN complete with flush bend and all other necessary fittings instead of C.I. high level cistern complete with flush bend and all other necessary fittings IN WHITE STOVE ENAMEL PAINT. (HSR 30.11)

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY LOW LEVEL VITREOUS CHINA WARECISTERN complete with flush bend all other necessary fittings instead of C.I. high level cistern complete with fittings. HSR 30.12. (i)

EXTRA OVER item nos.30.3 to 30.6 FOR PrOVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid. (HSR 30.13) (i) White

EXTRA FOR PROVIDING AND FIXING VITREOUS automatic flushing CISTERN INCLUDING FITTINGS and brackets instead of C.I. flushing cistern COMPLETE (HSR 30.37 (b) 10 Litres capacity cistern (i) White

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75]. (a) Bib cock long body.

Providing and fixing in position 15 mm i/d C.P. brass bib cocks of best quality (c ) Bib cock (HSR 30.75 (c ) )

Providing and fixing in position Best Indian make flexible tube connection (b) C.P. brass (i) 15 mm x 300 mm (HSR 30.82 (b ) (i) )

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. [HSR 30.119 (C). 1000 Ltrs. Capacity Water Tank

Providing and Fixing of Zet Connection (N.S)

Recovery of Items:- Good Tiles, Reserve price @ Rs. 5/- Each

Tiles Bats, Reserve price @ Rs. 500/- Cum

THE GYATRI COOP. L&C SOCIETY LTD. GEONG

SUS MANPOWER AGENCY