Miscellaneous repairing work and other development work for Nutan School and other location under SR (EZ) unit, Mumbai

Amount

ABSTRACT SHEET

PART - I - CIVIL WORKS

PART II : PH WORKS

PART III : ELECTRICAL WORKS

Description of Work / Item(s)

Amount

PART - I - CIVIL WORKS

Plain cement concrete using graded stone aggregate of 20 mm max. size including consolidation, finishing, curing, cost of form work, shuttering, centering etc. at all level and locations complete all as per specification & as directed by the Engineer- in- Charge.

Brick work at all levels & location using Ready mix cement mortar 1:4 using well burnt locally available bricks of approved quality including scaffolding, raking out joints above ground level simultaneous pointing below ground level, curing, scaffolding etc. complete all as per specifications & as directed by the Engineer- in- Charge.

a) In foundation & plinth, drain walls, chambers etc.

Reinforcement with TMT bars of Fe500D grade reinforced cement concrete conforming to IS at all floors & levels including, supplying, cutting, bending, fixing and tying in position with 1.6 mm dia soft drawn annealed binding wire including cost of binding wire, labour and welding of new reinforcement bars with existing reinforcement bars wherever required etc. complete all as per specifications and as directed by the Engineer- in- Charge. Note:- Binding wire required for the work will have to be supplied by the contractor & the same will not be measured for payment.

Random rubble masonry at all levels & locations using spotless black trap or approved locally available stone using Ready mix cement mortar 1:4 including raking out joints, scaffolding simultaneous flush pointing using through bond stones at every 900 mm in horizontal & vertical courses of Each layer including PVC pipe 75 mm dia weep hole at 1.5m c/c in horizontal & in vertical, curing, scaffolding etc. complete all as directed by the Engineer- in- Charge.

Rubble stone supplied by the contractor

Rubble stone supplied by the Department

Providing & laying rubble stone soling using spotless stones of consolidated thickness (150 / 230 mm) with stones vertically handset interstices packed with smaller stone chips, binding with murrum/crushed sand, watering, consolidating & finishing to required levels etc. complete all as directed by the Engineer- in- Charge.

Providing IPS flooring of following thicknesses at all floors & levels, in cement concrete 1:2:4 using graded stone aggregateof 10 mm max. size laid to proper level or slope in alternate bays in panels of required sizes finished smooth including providing aluminimum strip of size 25 x 2 mm wherever required, curing, including removing carefully existing damaged/ worn out flooring and disposing off debris within colony etc. complete all as per specifications & as directed by the Engineer- in- Charge.

a) 50 mm thick

Providing and fixing second class teak wood in frames of required sections for doors, windows, ventilators, clear storey window, partition, railing, battens & rafters etc. wrought framed and fixed in position including providing and fixing M.S. hold fasts of size 200 x 30 x 3 mm embedded in concrete block of P.C.C. 1:2:4 and fixing frame in position, labour for removal of door shutter carefully and refixing the same including applying one coat of approved wood primer & two coats of synthetic enamel paint to the exposed surfaces and two coats of bituminous paint to the surfaces of frames in contact with masonry concrete etc. including removing the old damaged frames and transporting to Deptt. Stores and making the adjacent plaster good to match with existing surfaces etc. complete all as directed by the Engineer- in- Charge.

Providing & fixing ordinary plain/ frosted/ Bajara sheet glass/ for MS openable/ louvers or aluminium sliding windows, glass doors, vision panels etc. of approved make of following thickness in various sizes as required at site, using first class glass oil putty of approved quality and make including supplying & fixing glazing pins, teak wood or aluminium beading, EPDM gasket etc with necessary screws, nails etc. (as required). at all floors & locations including cutting the glass to required size, removing the existing broken/ damaged glass panes from windows/ doors/ partitions etc. along with its old oil putty/ gasket/ beading etc. carefully and disposing off the un-serviceable material with in colony including wastage in cutting, transportation etc. complete all as directed by the Engineer- in- Charge.

b) 4 mm thick Bajra glass for windows/ louvers.

Supplying & fixing in position the 30/40 mm thick solid core block board flush door shutters with commercial ply on both side conforming to IS with external type teak wood lipping of section 30 X 20 mm/ 40 X 20 mm alround, fixing shutters in position to pressed steel door frames/wooden frames at all floors by cutting/ planning if necessary including supplying & fixing heavy duty MS oxidised hinges including cost of fixing the fittings, painting the shutters all over with two coats of synthetic enamel paint of approved make & colour over one coat of approved primer etc. including removing the old damaged shutter and transporting to Deptt. stores all as per specifications & as directed by Engineer- in- Charge.

b) For Door 40 mm thick.

Cement plastering using factory manufactured pre mix/ready mix mortar of approved make minimum composition of C:S is 1:4 suitable for internal plastering to wall and ceiling finished smooth over brick walls or concrete surfaces including acrylic based membrane curing of M/s. Anuvi Chemicals/ Fosroc/ Dr. fixit at all floors and levels including scaffolding, removing existing damaged/ worn out plastering and disposing off debris with in colony etc. complete all as per specifications and as directed by Engineer- in- Charge.

a) 12 mm thick.

b) 15mm thick.

Sand faced cement plaster 20 mm using factory manufactured pre mix/ ready mix mortar of approved make minimum composition of C:S :: 1:4 suitable for external plastering over brick walls or concrete surfaces with base coat of 12 mm thick and finishing coat of 8 mm thick final rendering, including acrylic based membrane curing of M/s. Anuvi chemicals/ Fosroc/ Dr. fixit at all floors and levels including removing existing damaged/ worn out plastering and disposing off debris with in colony etc. complete all as per specifications and as directed by Engineer- in- Charge. (Scaffolding shall be paid under relevant item) NOTE: The contractor must take full precautions that original brick work is not damaged while dismantling of plaster. Incase of any damage the same shall be made good with 25g chicken wire mesh at his own cost. No separate payment for any additional thickness of plaster if any will be made. Contractor must visit site and acquint himself with the condition of building.

Providing and applying one coat of white cement based wall care putty of approved make over entire surface including preparing old painted surfaces by thoroughly scrapping oil bound distemper /acrylic emulsion / white wash etc, filling up the cracks, crevices, depression, holes, including sand papering and making surfaces even and smooth dusting /cleaning, applying one coat of approved cement primer, scaffolding , covering the furniture etc with tarpaulins or eqivalent covering materials, cleaning of all surfaces etc.& disposing of debris outside colony etc.complete as per specifications and as directed by the Engineer-in-Charge.

Repainting of old painted surfaces with two coats of Oil bound distemper of approved make & shade over two coats of approved primer consist of thoroughly scrapping oil bound distemper/ white wash surface, applying a coat of approved cement primer, filling upthe cracks with approved crack filling compound, applying approved stucco putty to entire surface to fill up crevices, mild depression etc. thoroughly scrapping the surface, applying 2nd coat of approved cement primer over putty work, apply two coats of Oil bound distemper paint including necessary covering material and removal of splashing & droppings from floors, walls including scaffolding, ladder as required & disposing off debris within colony etc. complete all as directed by the Engineer- in- Charge.

Repainting of old painted surfaces with two coats Flat oil paint of approved shade and make over two coats of approved cement primer consist of thoroughly scrapping of all types of old painted surfaces , applying a coat of approved cement primer, filling upthe cracks with approved crack filling compound, applying approved stucco putty to entire surface to fill up crevices, mild depression etc. thoroughly scrapping the surface, applying 2nd coat of approved cement primer over putty work , apply two coats of Flat oil paint including necessary covering material and removal of splashing & droppings from floors, walls including scaffolding, ladder as required & disposing of debris within colony etc. complete all as directed by the Engineer- in- Charge.

Painting old wood/ steel work with two coats of Synthetic enamel paint of approved shade & make over one coat of primer including preparing surfaces, through scapping of MS work, filling with putty wherever required, scaffolding & cleaning etc. complete all as per specifications & as directed by the Engineer- in- Charge.

a) On wooden surfaces with two finishing coat over a coat of wood primer.

b) On steel surfaces with two finishing coats over a coat of steel primer.

Demolishing RCC works by chiseling at all levels including scaffolding,cutting of reinforcement bars by gas cutting, straightening and stackingof steel bars and disposal of unserviceable materials complete all per specification & as directed by the Engineer- in- Charge.

Demolishing brick/ stone masonry in cement mortar and plaster at all floors & levels including scaffolding, stacking of serviceable materials & disposing off unserviceable materials etc. complete all as per specification & as directed by the Engineer- in- Charge.

a) Brick/ Stone masonary work.

a) Supplying and erecting M.S. tubular scaffolding using 'H' frames of M/s. Acrow India (or) equivalent with horizontal and vertical rows @ suitable spacing as per I.S. specification which should be suitably overlapped at junctions and cross braced wherever required and securely tied, supporting the scaffolding with building members as permitted by the Engineer-in-Charge, including all pipes of scaffolding shall be atleast 40mm n.b. dia heavy class seamless pipe, providing necessary safety belt and helmet to the workers and dismantling & taking back the scaffolding, safety belt and helmet after the repair works are completed all as per specifications and directed by the EIC.

a)M S Steel scaffolding

Repairs to damaged RCC structural members at all locations/ floors using polymer modified cementatious mortar, for strengthening the existing RCC structural members using acrylic based polymer and comprising the following operations: 1. Breaking cracked / spalled concrete members along the cracks with plaster, including removing and stacking of all unserviceable material at site,simultaneous transportation and disposed at a location in Anushaktinagar as identified by EIC. complete all as per specifications and as directed by the Engineer-in Charge. 2. Exposing and cleaning the reinforcement thoroughly by light tapping / wire brushing of using strong emery paper and finally by acetone /rust remover of Dr. Fixit / Anuvi chemicals / Fosroc or other eqivalent. 3. Applying a coat of polymer and cement slurry in the ratio 1:1 by volume to the reinforcement bars. 4. Polymer required for the work shall be procured by the Agency from approved Manufacturers Like M/s Astra , M/s Anuvi, M/s Apcotex or other approved equivalent manufacturer confirming to technical requirements as below and the invoices/challans etc to be submitted to EIC for record. Appearance: Milky white Ph- value : 9-10 Specific gravity : 1.055+/-0.005 Solid contents(%w/w)-: 44+/-1 Viscocity at 25 degree C temperature (in sec): 15-20 Testing of the material as per relevant codes at NABL approved third party Lab. is to be done by the Agency for every batch/lot of supply. 5. Bond coat should be applied @ 0.37 ltr./layer/sq.m. 6. Minimum FM of silica sand should be 2.10

a) Building up with polymer modified cementatious mortar for RCC structural members etc. in layers not exceeding 20 mm in a day (proportion – cement 50 Kg. : Silica sand 125 Kg. : polymer liquid 10 ltrs.) with necessary bond coat (polymer : Cement = 1:1 by volume) for tack coat and also for subsequent layers using polymer including curing, covering the flooring /window with tarpaulins or equivalent covering material to avoid deposition of polymer mortar and cleaning of floor / windows thoroughly on completion of repair work etc. complete all as per specifications and as directed by the Engineer-in-charge. Note : Polymer used for this work in Kg shall be measured for payment.

b) Repairing with polymer bonded mortar up to 35mm thick in layers of not exceeding 20mm (with out chicken mesh) in a day (proportion- cement 50 Kg : silica sand 125 Kg) with applying protection coat / bond coat to reinforcement, bond coat to old concrete and bond coat for every successive layers of 20mm thick in proportion polymer : Cement-1:1 by volume as per specification including covering the floor/windows with tarpaulin or equivalent covering material etc., and cleaning after repair etc., complete all as per specifications and as directed by the Engineer in charge. The rate is inclusive of supplying and applying protection coat /Bond coat of polymer.

c) Repairing with polymer bonded mortar average 70 mm thick in layers not exceeding 20 mm in a day (proportion – cement 50 kg : silica sand 125 Kg. ) with applying protection coat / bond coat to reinforcement and bond coat for every successive layers of 20 mm thick in proportion Polymer : cement – 1:1 by volume as per specification including one layer of Chicken mesh 22 gauge, including covering the floor / windows with tarpaulin or equivalent covering material etc. and cleaning after repairs, curing etc. complete all as per specifications and as directed by the EIC. The rate is inclusive of supplying and applying protection coat /Bond coat of polymer.

Providing & laying at all floors & levels first quality ceramic tiles of minimum thickness as specified by the manufacturer of M/s. H & R JHONSON (INDIA) Ltd. or euqivalent approved make of approved colors, shade and texture in flooring/ dado/ skirting as per approved pattern incluidng cost of all materials including of cutting the tiles to required shape, wastage, pointing the joints with white cement mixed with matching pigments to match the colour of the tiles, finished to line, level, slope & plumb, final cleaning of surface as required, curing, making necessary opening cutouts etc. and including removing existing flooring/ dado and disposing off debris complete all as per specifications, relevant IS code & as directed by the Engineer- in- Charge.

a) In flooring with tiles of size 300X 300 (approx size) similar to white/ ivory/ other approved colour quartze series of M/s. H & R Johnson or equivalent approved make with 20 mm thick 1:4 ready mix Cement mortar bedding.

c) In Dado/ skirting with tiles of size 300 X 450 mm (approx size) similar to Digital HD series tile Linea blue/ snow white of M/s. H & R Johnson (India) Limited or euqivalent approved make fixed over 12 mm thick ready mix cement mortar 1:4 backing/ fixed directly over existing tile with polymer cum cement based adhesive (Type-II) manufactured by Roffe Construction or M/s. Bal Endura Chemicals or other approved equivalent jointed with cement slurry & grouted with pigment of matching shade & finishing the top of skirting/ dado etc. complete.

Supplying & fixing 25 mm thick PVC integral free foam sheet in form of flush finish door shutter, manufactured by M/s. Jain Irrigation Systems Ltd. (Ex-cel sheet) or other equivalent approved make of white colour, solid section, extruded rigid, light weight sheet with fine & homogeneous closed cell structure with smooth, glossy, hard surface finish on both sides including providing recessions for hinges and providing & fixing 3 nos. 100 mm heavy duty S.S. hinges and 2 Nos. 100 mm heavy duty Aluminium baby latches, 2 nos. of 100 mm Aluminium Bow handles with back plate and including providing a vision panel opening of size 300 mm X 200 mm including providing and fixing PVC moulded louvers on both faces in the opening of vision panel with ss screws, all edges to be smooth finish with mixture of PVC powder & solvent etc. complete all as per specification and as directed by the Engineer- in- Charge. Note:- 1) The entire door shall be jointless shutter. 2) The sizes shall be approximately 650 mm x 2000 mm, owever exact dimensions shall be measured at site before manufacturing.

Providing and fixing in position at all floors, levels/ heights 18 mm thick mirror polished marble stones for door & window framing work in single piece of approved shade, finished sizes as directed including machine cut/ hand cut, final cleaning, moulding and polishing of exposed edges, in line, level, plumb including removing existing window/ door frame, shutter & fittings etc. and depositing the same at Deptt. store etc. complete all as per specifications, drawings & as directed by the Engineer- in- Charge.

a) 18 mm thick marble stone in overlapping & stepped pattern fixing the stone with ready mix cement mortar 1:3, 20 mm backing & overlapping of 20 mm shall be fixed with Araldite adhesive. (For door frame sides & top and window frame bottom cill) ( Note: Exposed surface on Elevation & exposed vertical finished face shall be measured for payment in Sqm. Overlapping & edges etc. shall not be measured.)

b) 18 mm thick machine cut and single side machine polished Baroda green marble stone for window jamb, bottom of lintel, door cill in single piece laid over 20 mm thick 1:4 cement mortar including half round moulding & polishing of exposed face etc. complete.

Supplying, fabricating and fixing in position at all floors Aluminium sliding/ top hung/fixed/ adjustable louvered windows & ventilators with rivit joint of specified size, made of integrated bronze anodised matt finished (15 micron thick) aluminium section (extruded) including for making exhaust fan frame work, handles of specified size etc. of approved manufacutres for following types with extruded sections of Jindal / Hindal/ Aluminax or other approved equivalent make of approved sections with size and wights as directed for frames and shutters (including wastages if any) confirming to relevant IS specifications with all approved Bronze anodised aluminium fittings and accessories, latching fixture, 2/3 rollers with ball bearing of superior quality all as shown in the drawing including providing and fixing aluminium channel beading/ glazing clips fixed with necessary bronze anodised screws, grouting the gap with sealant and including dismantling of existing window frame and shutter, glass and depositing same to Deptt. store etc. all complete generally as per drawing, specifications etc. all as directed by Engineer- in- Charge.

Providing & laying machine cut machine polished Cuddapah stones as mentioned followings for kitchen platform top, vertical support/ shelves/ facia, beading etc. and including necessary cement mortar for backing/ bedding, close jointed and grouted with matching cement slurry and finished to line, slope, level, plumb, curing etc. as required including cutting of stone slabs, wastage, making cut outs wherever required etc. all as per specifications and as directed by the Engineer- in- Charge.

a) For kitchen platform top, upto 750 mm wide and upto 1800 mm length in single piece consisting machine cut machine polished on one side, 30 mm thick Cuddapah stone (Kitchen pltform top) fixed with 20 mm thick 1:4 ready mix cement mortar including providing cut out if any, moulding and polishing the edges etc. complete.

Providing assistance to the departmental technician for attending the complaints of various nature on working days/ holidays/ beyond office hours viz etc. in various flats and buildings including neccessary tools and manpower, loading, unloading etc. complete all as directed by the Engineer- in- Charge. (Working hours should be 8.30 Hours with 30 minute lunch break)

a) Supply of skilled Labour (Plumber & Carpenter).

a) Supply of un-skilled Labour.

Carrying out miscellaneous welding work at all levels & location for MS windows, ladders, fencing, gate etc. including required peg stay, cleat, louver cleat, hinges, member, hook, bolt, nut other required materials, labour, welding machine, welding rod etc. complete all as per specifications & as directed by the Engineer- in- Charge.

Repairing existing damaged PVC Sintex tank (overhead & loft tank) at base, side, top & outlet portion by welding using special quality heavy duty PVC material including all plumbing work ( disconnection, connection, & restoration), testing for water leak proofness etc complete all as per specifications & as directed by the Engineer- in- Charge.

Providing chemical based water proofing treatment of approved make (Indofil/ Pidilite/ Asian) over bath/ WC brick bat coba & other locations as per the following procedure: a) Cleaning completely the existing surafce to remove all dirt with wire metal brush. b) Applying a primer coat of water proofing compound (diluted with clean water as per recommendations of manufacturer) over the entire area to be treated including filling up of cracks, if any with CM-1:3 mixed with waterproofing compound. c) Applying a first coat with water proofing compound with cement in 1:1 ratio. d) Providing and spreading of polycon based fibrous water proofing net for entire area including lapping as per manufacturer's specifications immediately after applying first coat and curing. e) Applying second coat with water proofing compond with cement in 1:1 ratio over the polycon based fibrous net. f) Applying top coat with undiluated water proofing compound. Notes: i) The entire work shall be carried out a per manufacturer's specification and as directed by the Engineer- in- Charge. ii) The contractor shall furnish guarantee bond on appropriate stamp paper in the proforma as per Appendix 'D' for the entire waterproofing treatment for maintaining the surroundings and under side surfaces of the waterproofing treatment in bone dry condition for 5 years. During the guarantee period the contractor shall attend all leakages, defects etc. if noticed, free of cost, starting the work of checking up and rectification within a week's time from the date of intimation about such leakages/ defects.

Providing and fixing Hydraulically pressed factory made kerb stones full bull nose /half battered from approved manufacturers like M/s Sneh Tiles or other approved equivalent , made up of cement concrete grade not less than M-30 and having size 600 X 450 X 125 mm , of approved including removing the existing kerb stone stacking at designated place by EIC, necessary foRm work, compaction, finishing, curing, fixing with CM 1:3, jointing and pointing in cement mortar 1:3 including earth work and 75 mm thick & 200 mm wide PCC 1:3:6 for foundation below kerb stone etc. complete all as per specification and as directed by the Engineer in charge

Providing and fixing 60 mm thick (min.) factory made interlocking paver blocks of approved make (M/S.Super tile or other Equivalent), approved colour, shade, size, shape semi reflective paver blocks manufactured with cement concrete grade not less than M-35. including supplying & laying 50 mm thick well graded stone dust evenly spread over the sub base including consolidation of sub base properly vibrating with th surface vibrator, finishing to line, level and slope, finally filling the joints with fine clean sand and cleaning the surface including removing existing shahabad stone and storing serviceale materials and disposing off the debris out side of the colony, including taking permission from statutory authority etc complete all as per specification and as directed by the Engineer in charge.

Painting the Kerb stones of both existing and new ones in pattern with two coats of flat oil paint of approved colour and shade over one coat of approved primer including preparing the surface by brushing manually/washing with water jets wherever required and complete all as per specification and as directed by the Engineer in charge.

Supplying, laying and formation of water boundmacadam (WBM) subbase with 90-40 mm singlestone aggregate, stones screenings 12.5 mm insingle layer of 150 mm thick laid loose andconsolidated to 115 mm thickness includingbreaking stone if required, screening, sorting,spreading to regular line, level template andsupplying and binding with murrum, watering, consolidating each layer properly with 8 to 10 tonnes Hydralic vibrator roller including cost of all materials, labour, finishing to proper gradients, camber etc. complete all as per speciications and as directed bythe Engineer-in-Charge.

Providing, laying, spreading and comapcting Factorymade Wet Mix macadam using 50mm I.R.C. hard trap metal & blended with 25% lime including premixing of material with water in mixing plantfor Wet mix macadam, carraiage of mixed material by tipers to site and sprading mechanically and compacting it by 8 to 10 ton Hydralic vibrator rollerwateringall etc. complete all as directed by the Engineer-in-Charge.

Providing and laying hot mixed hot laid 38 mm averageconsolidated thickness premixed bituminous macadamover existing surface including filling pot holes and roadcuts using approved graded I.R.C. metal 32 mm down 3.7% to 4.7 % bituminous of grade 60/70 (VG20) including theW.B.M. road by removing loose material from potholesand existing road surface with wire brushing, brooming and mechanical spreading, machine laying, (sensor paver) bituminous course to correct line and grade, camber etc. complete compacting thoroughly with 10/12 Tone hydrolic roller including applying a tack coat of bitumen 60/70 (VG20)grade @ 7.5 kg./10 Sq.M. specifications all as directed bythe Engineer-in-Charge

Providing and laying hot mixed hot laid premixedbituminous seal coat of 12 mm consolidated thicknessover asphalt macadam as wearing course on road surfaces using 7.5% bituminous grade 60/70 (VG20) including machine mixing, laying by mechanical spreading machine (sensor paver) and compacting thoroughly by 10/12 Tone Hydralic vibrator rolleretc.to correct level and line, grade, camber applying a tackcoat of bitumen 60/70 (VG20) grade @ 7.5 Kg./10 Sq.M.etc. complete all as per specifications and as directed bythe EIC.

Description of Work / Item(s)

Amount

PART - II - PH WORKS

Providing & fixing on Exposed or concealed surfaces the following dia Chlorinated Polyvinyl Chloride (C-PVC) pipe of specified class of M/s. SUREME/ PRINCE or other approved equivalent consisting following items of work:- i) Supplying & fixing C-PVC pipes including necessary all fittings conforming to IS 15778. ii) Laying and fixing the pipe and specials on exposed surfaces to correct line, level and plumb for water supply line, overflow and vent using M.S. nails/ screws, rawl plugs, wooden gutties and branded clamps of Supreme/Prince make to the pipeline as per the site requirement. iii) Testing the pipe line to a hydraulic pressure as per manufacturers cataglouge for leak proof joint or as per relevant code. iv) Making leak proof threaded/ solvent joints. including cutting the pipe, Joint preparartion, cleaning, marking, application of solvent, assembling, curing etc. and the cost of jointing cement solvent materials. v) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. proof joints. vi) Providing and fixing C-PVC jointable/ threaded fittings such as Union, Nipples, Bendes, Elbows, Tees, Reducers, End caps, Couplers, Adaptors, Saddles, Plugs, Tank connectors, Expansion loops, Bypass bends, etc. vii) Including removing existing GI pipe line with fittings and specials etc. Note:- All brass threaded elbows and fittings shall be with additional support type of M/s. Prince, Supreme or other equivalent approved by Engineer- in- Charge including necessary fixing arrangement such as screws, plug etc. complete. (Mode measurement:- The measurement shall per Unit RM length of pipe line laid or fixed. The measurement shall be taken along centre line of pipe. No measurement shall be recorded saperately for fittings etc. ) SDR 11 Pipes and Fittings

a) 15 mm n.b.

b) 20 mm n.b.

c) 25 mm n.b.

d) 32 mm n.b.

Providing & fixing European water closet/ Anglo Indian WC of approved make with 'P' or 'S' trap wash down pattern European water closet best indian make in white glazed vitreous of size 460 mm X 330 mm and including cost of removing the existing one & disposing off debris etc. complete all as per specifications and as directed by the Engineer- in- Charge.

Providing & fixing Orissa pattern W.C. of approved make comprising of Orissa pattern W.C. with 'P' or 'S' trap best Indian make in white glazed vitreous china ware of size 580 mm X 400 mm including the cost of removing the existing damaged/ broken and making good the surrounding with cement mortar/ concrete tiles maching to the existing finish & disposing off debris etc. complete all as per specifications and as directed by the Engineer- in- Charge.

Providing & fixing wash basin of approved make with plain rims in white glazed vitreous chinaware supported on suitable wall brackets and of size mentioned below, including cost of removing the existing wash basin and necessary C.I. brackets shall be provided by the contractor including fixing the existing fittings such as pillar cock, inlet connection, stop cock, waste coupling, bottle trap etc. & disposing off debris, complete all as per specifications and as directed by the Engineer-in-Charge.

i) 550 mm x 400 mm.

Providing and fixing approved quality 10 Ltrs. capacity (PVC flushing cistern) SLIMLINE or CERA or approved equivalent flushing cistern High/ low level conforming to relevant IS:7231 including all internal fittings, pull chain/ Knob, heavy duty PVC pipe/ bend connecting with existing concealed/ open pipe leading to water closet and reinstating/ making joint leak tight etc. mounted on brackets including cost of removing the existing one depositing to Deptt. stores etc. complete all as per specifications and as directed by the Engineer- in- Charge.

Providing & fixing large flat back half stall urinal of size 610 mm X 400 mm X 380 mm of M/s. Hindustan Sanitaryware/ CERA Brand/ Neycer orapproved equivalent supported on suitable wall brackets with 32 mm n.b. heavy quality Dripless/ Kingston make C. P. brass bottle trap with extension piece and wall flange suitable heavy C. P. brass wasteincluding C. P. dome grating etc. complete all as directed by Engineer- in- Charge.

Kitchen sink waste coupling of 100 mm nominal size with 32/ 40 PVC reducer cum adaptor, PVC cup having minimum wall thickness 1.5 mm, stainless steel dome cup having minimum wall thickness of 0.8 mm, stainless steel strainer cum jali having miniumum wall thickness of 0.8 mm, SS screw, the minimum weight of SS dome cup with stainer cum jali & base nut shall not be less than 125 grams, suitable for S.S kitchen sink of FRANKE/ NIRALI / BPI make.

Providing & fixing large flat back half stall urinal of size 610 mm X 400 mm X 380 mm of M/s. Hindustan Sanitaryware/ CERA Brand/ Neycer orapproved equivalent supported on suitable wall brackets with 32 mm n.b. heavy quality Dripless/ Kingston make C. P. brass bottle trap with extension piece and wall flange suitable heavy C. P. brass wasteincluding C. P. dome grating etc. complete all as directed by Engineer- in- Charge.

15 mm dia. CP brass screw down, non fancy BIB TAP having full turn of M/s. TECHNO or other approved make conforming to IS 781-1984 and its latest amendments and ISI marked. (Minimum weight 400 gms).

15 mm dia. CP brass screw down, non fancy Pillar tap having full turn of M/s. TECHNO or other approved make conforming to IS 1795-1982 and its latest amendments (Minimum weight 650 gms).

15 mm dia. CP brass screw down, non fancy STOP COCK having full turn of M/s. TECHNO or other approved make conforming to IS 781-1984 and its latest amendments and ISI marked. (Minimum weight 400 gms).

Description of Work / Item(s)

Amount

PART - III- ELECTRIRAL WORKS

900 mm Sweep similar to samrat ES model of M/s Havells with safety chain

1400 mm Sweep similar to samrat ES model of M/s Havells with safety chain

Light point wiring

Fan point wiring

5A socket point

Exhast fan

63A 4P RCBO

32A DP switch

10 Way SPN DB