REPAIR TO TOILETS, BATHROOMS, SANITARY FITTINGS AND OTHER CONNECTED B/R WORKS INCL PVC DOOR OF MARRIED AND OTM ACCN AT MIL STN DAGSHAI UNDER GE KASAULI

Amount

Schedule 'A' Section - I

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.50 sqm each including iron mongries

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm but n.exe 4.0 Sqm each including iron mongries

Taking down shutter of any description exe 1 Sq.m but n.exe 2.0 Sqm each

Dismantling timber scantlings 40 sqcm and under in section, in any position framed / Unframed work complete all as specified by the Engr-in-Charge

Dismantling wrought iron or mild steel work of any description any position not otherwise provided complete all as specified

Dismantling posts or struts (Wood, steel or RCC) any section including taking out embedded portion in concrete, brick work, masonary etc, and making good disturbed ground complete all as specified and directed

M&L for brick work with sub class `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed including demolition of brick masonary built in cement mortar including all quoins arches pillars complete all as specified and directed

M & L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and fair without using extra cement including taking down cement plaster on brick or stone wall, Ceilling etc including racking out joints, hacking for key scrubbing down with water etc to receive new plaster all as specified and as directed

Ditto as per item 8.00 above but in CM 1:6.

M & L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and fair without using extra cement complete all as specified and directed all as specified and as directed

M&L preparation of new plastered surface of wall and applying two coat of oil bound distemper of any approved tint over a coat of primer complete all as specified and directed

M&L preparation of new plastered surface of wall and applying two coat of cement base paint over a coat of primer on walls complete all as specified and directed

M&L preparation of new plastered wall surfaces and applying two coat of exterior emulsion paint over a coat of primer of approved tint and make complete all as specified and directed

M&L Non skid ceramic coloured tiles 7mm to 8mm thick (squre/rectangular) area of each tile exc0.11sqm but not exc 0.18 sqm in floors , set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 20 mm thick screed bed with cement mortar 1:6 complete all as specified.including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 20mm thick screed bed in cement mortar 1:6 complete all as specified including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

Ditto as per item No 15.00 above but in skirting set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10mm thick backing coat on vertical surfaces of wall in cement mortar 1:4 complete all as specified and as directed.

Material and labour for Glazed ceramic coloured tiles in vertical surfaces exc 0.08sqm and n exc 0.16sqm, 7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10mm thick backing coat on vertical surfaces of wall in cement mortar 1:4 complete all as specified and as directed including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L for 16 to 18 mm thick granite stone machine cut (table rubbed & polished) in one piece as in steps,jambs,pillars,windows cills,cooking platform and similar work bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigments to match the shade of granite stone including grinding and polishing including making hole in platform and screed bed for bedding 20 mm thick in cement mortar 1:6 ,complete all as specified. including dismantling old unsv granite stone.

Rounding to edges of stone slabs to one edge, such as in steps and other similar situations

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm with plugs, washers and wastes; including waste coupling and waste pipe bedding in cement mortar to dwarf wall or fixing cantilever brackets and connecting union to pipe etc complete all as specified.and directed

S&F in repair stop valve 15 mm cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union etc complete all as specified.

ditto as per item 21.00 above but 20 mm dia

S&F in repair 15mm bore Bib taps, chromium plated cast copper alloy, fancy type, screwed down for iron pipe or for brass ferrule etc complete all as specified and directed.

Ditto as item No 23.00 above but long body

S&F in repair 15mm bore angle cock, chromium plated, brass, fancy type, screwed both ends for iron pipe or for union etc complete all as specified and directed.

S & F in repair for 15mm bore pillar tap fancy type, cast copper alloy chromium plated screwed down, high pressure with crutch or butter fly handle etc complete all as specified and directed.

S&F in repair chromium plated wall mixer 3 in one with crutch and multi flow hand shower with 1.5 mtr flexible tube (chrome) including fixing to steel pipe or unions three joints to steel pipes or union and plugging and screwing to walls etc complete all as specified

S&F in repair 15 mm bore brass Chromium plated wall/basin/sink mixer for mixing hot & cold water screwed down for iron pipe etc complete all as specified.

S&F in repairs Vitreous China wash hand basin white with pedastal flat back size 550x400 mm including brackets and waste coupling , complete all as specified

Supply and fix in repair vitreous china wash basin counter sunk type oval shape, star white including waste coupling ,chromium plated, waste pipe fixing brackets, cutting for and pinning in ends of brackets complete all as specified and as directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts,) complete incl PVC P or S trap 110 mm dia and making good to floor to match with adjoining surfaces including plastic water closet seat cover white closed pattern with flat bottom mild steel chromium plated of aluminium hinging device etc complete all as directed by Engr-in-Charge

S&F as in repair fixing WC Orissa pattern of size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) includung provision of lime concrete bedding and PVC S trap of 110 mm dia etc complete all as specified and directed by Engr-in-Charge

S&F in repairs Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement;including waste pipe, waste coupling and urinal spreader fixing with 15 mm dia pipe all as specified and directed

S&F in repair PVC bath cabinate with mirror ,complete all as specified.

S&F in repair 10 ltr capacity PVC valveless syphonic action type flusing cistern low level white with inlet ball valve float and handle including bracket fixed etc complete all as specified

S&F in repair PVC connection 15mm bore with PTMTnuts of length 450mm etc complete all as specified

S&F in repair 32mm dia PVC flexible waste pipe for urinals/WHB/sink all as specified

S&F in repair stainless steel soap dish of approved pattern all as specified and as directed

S&F in repair CP toilet paper holder all as specified and as directed

S&F in repair CP grating of 100 mm da including jointing with solvent cement all as specified and as directed

S & F in repair 20mm dia,D type, 60cm long aluminum anodised towel rail, complete.

S&F in repair for 15 mm ball valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or ferrule and fixed, complete all as specified..

S&F for 15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs etc complete all as specified. Including taking up or down steel tubing and connections upto 15mm bore.

ditto as per item 45.00 above 20 mmdia

S&F mild steel prepainted 4 pin cloth hook hanger fixed to wall complete all as specified and as directed.

M & L for 500 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including PTMT float valve of 15 mm dia and taking down old unserviceble PVC water tank all as specified in SSR Part-I completed and as directed by the Engr-in-Charge

ditto as per item 48.00 above but 1000 ltr capacity

M&L for precast RCC (1:2:4) type B-1 using 20mm graded mechanically crushed stone aggregate as in landing cover slab for kittchen platform manholes , septic tank set in cement mortor ( 1:6) including necessary form work complete all as specified and as directed. (Reinforcement shall be measured separately) including demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in position not otherwise specifically provided for complete

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including crancking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.5mm dia or securing with clips quality confirming to deformed or twisted bars complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors / wall complete all as specified and as directed including taking up or down waste and vent pipes of any type complete.

Ditto as per item 52.00 above but 110 mm dia PVC (SWR pipe)

S&F in repair 75 mm dia PVC(SWR) floor trap, with grating including jointing with solvent cement etc complete all as specified.

S&F in repair PVC(SWR) bend 110mm dia bore complete all as specified and directed by Engr-in-Charge

S&F in repair PVC(SWR) bend 75mm dia bore complete all as specified and directed by Engr-in-Charge

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F 35 mm thick factory made, 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated etc complete, all as specified .

S & F 35 mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass ,gauge etc ( without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8 clause 8.24(a), supplied and fitted to chowkats.

M&L 2nd class hardwood as in plain, solid straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed

S&F mild steel cupboard shutter with frame Godrej pattern, made out of 22 gauge mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type, size 65mm, 4 levers with escutcheon pushes and two keys) with & including two coats of spray painting with sysnthetic enamel paint with approved tint over a coat of red oxide primer including fixing with 6 Nos 12mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete all as specified and as directed.

S&F 100mm butt hinges, cold rolled mild steel medium weight

S & F for Aluminium anodized 150 mm long barrel tower bolt of extruded section and fixed.

S&F 100mm longth extruded aluminium alloy anodized handles febricated type

S&F 250 mm MS ordinary rat tail rod pattern spring including roller and roller plate fixed as in repair including taking down the unserviceable existing complete all as directed.

S&F 250 mm long Aluminium alloy anodised sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed etc complete

M & L for two coats of synthetic enamel paint over coat of pink primer on new wooden surfaces of any description not otherwise described over 10 Cm width or girth including preparation of surfaces complete all as specified and as directed by the Engineer-in-Charge

S &F Powder Coated Anodised aluminium frame for doors, windows, parttions , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S &F powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S &F powder coated aluminium window and ventilator shutters, side hung type without sash , aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws anodised aluminium fittings such as peg stays 150 mm long (1 no) hinges type B-1 100 m long(2 Nos) suitable handle(1 Nos). and tower bolt 150 mm (2 No) complete al as specified.

S&L for sheet glass ordinary quality 4.80mm thick in aluminium windows of area of each pane n.exc 0.50 Sqm including glazing clips , rubber beading etc,,or fixed portion complete all as specificed and directed by Engr-in-Charge

S&L for Figured glass 5 mm thick pin head type in aluminium windows of area of each pane n.exc 0.50 Sqm including glazing clip and rubber packing complete all as specificed and directed by Engr-in-Charge

S & F for galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed by the Engineer-in-Charge.

S &F powder coated aluminum grill of approved pattern / design with approved standard section and fixed to the existing window frame with aluminum U clip of appropriate size and CP brass / stanless steel screws @200 mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodiesd aluminium standard section around the opening all complete all as specified and all as directed.

S&F in repair 9mm thick pre-laminated particle board interior grade, both side lamination of approved colour and pattern fixed to wooden / aluminium frame work as in door/cupboard shutters and necessary fittings complete all as specified including dsmantling of wall and ceiling board (fibre, pulp, insulation, etc) or insulationboards, and cover fillets etc,, any thickness complete

M & L for 6 mmPlywood, grade BWR, type BB, fixed with screws to timber frame work all as specified including dsmantling of wall and ceiling board (fibre, pulp, insulation, etc) or insulationboards etc,, any thickness etc. including cover fillets complete

M& L for PVC edge strip of 18/19 mm wide, colour and pattern as approved fixed with adhesive as per specified and as directed

S&F in repair Continuous (piano) hinges,mild steel, bright finish or elec trogalvanised , , bright finish width of flaps(when open) 30 mm complete all as specified.

S&F 100 mm long extruded stainless steel handle fabricated type anodised, complete all as specified.

S&F Hasp and staple, safety type,of aluminium anodised including bolt to hinge plate and fixed with screws 100 mm size complete all as specified.

S&F magnetic steel stopper catcher holder for cup board of approprite shape and size all as directed

M&L for 18/19 mm Pre laminated particle boards,interior grade,prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with nails and fixed to wall with scews or necessary fixing arrangent complete all as specified and as directed including dsmantling of wall and ceiling board (fibre, pulp, insulation, etc) or insulationboards, kitchen cupboard including piano hinges and handle and cover fillets etc,, any thickness complete

M&L in repair for PVC tiles / sheets 1.50 mm thick laminated plain coloured, marbled mosaic or motled finish, laid with approved rubber based adhesive in floors incl taking down old sheet complete all as specified & directed

M&L for cement concrete 1:2:4 type B-1 ( using 20mm graded stone aggregate) as in hard standing including necessary form work and finishing surface even and fair without using extra cement complete all as specified and directed including demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials and

Material and Labour Framed work such as grills, gratings,railing etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified.

Material and Labour for Welded steel wire fabric n.exc 4 Kg/Sqm supplied and fixed complete to wood or steel members complete all as specified.

M&L for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified & directed complete all as specified and directed by Engr-in-Charge

M&L for cement concrete 1:4:8 type D-2 ( using 40mm graded stone aggregate) as in sub base floor and in foundation including necessary form work complete all as specified and directed.including demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials )

M&L for PCC Type B1 1: 2:4 (20 mm graded stone aggregate ) Providing, cement concrete in mud stops, rounded or chamfered on edges as in coping ,kneelers , appex stone, etc .including demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials )

M&L Machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade and incl laid over 50 mm thick sand cushioning .all as specified and as directed

Ditto as per item 91.00 above but interlocking pavour block with pigmnet .

M&L for Chequered cement concrete tiles 30 cmx 30cm x 25 mm thick, with grey cement and pigment set jointed and pointed in neat cement slurry over and including 20 mm thick screed bed in CM 1:6 in floors with grey cement and pigments complete all as specified and directed.

Amount of credit of Rs. 71066.41 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender.

Sagar Builders

Durga Construction

RR Builders

R B TRADERS

R. P. Suppliers and Construction Co.