GE/863/EWS-T-33 OF 2025-26 SPECIAL REPAIR TO BLDG NO T-25 AND T-180 AT AVERIPATTI

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed by Engr in Charge.

Demolition of precast concrete articles and precast concrete block walling, built in cement mortar or cement lime mortar for ashlar facings, dressed stonework, complete all as specified and directed by Engr-in-charge.

Demolition of stone/boulder masonry built in cement mortar or cement lime mortar for ashlar facings, dressed stonework etc complete all as specified and directed by Engr-in-charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid,bedded & pointed in any mortar complete all as specified and directed by Engr in Charge.

Dismantling of plain or corrugated steel sheeting, any guage, thickness from roof covering complete all as specified.

Dismantling wall and ceiling boards of any description or any thickness including cover fillets complete all as specified and directed by Engr in Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed by Engr in Charge.

Taking down cement or cement lime plaster any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr in Charge.

Taking down chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each.

Taking down chowkats or frames(without taking off shutters from the frame) area not exc 1.5 Sqm each.

Taking down shutter of any description exc 2 Sqm each.

Taking down shutter of any description exc 1 Sqm but n exc 2 sqm each.

Taking up or down steel tubing 15 mm bore, and connections, including cleaning for re-fixing or removal to store in repairs complete all as specified.

Taking up or down steel tubing 20 mm bore, and connections, including cleaning for re-fixing or removal to store in repairs complete all as specified.

Demolition of RCC work of any description and any position.

Demolition and breaking up drain pipes(salt, glazed ware,AC or reinforced concrete) 200mm/150mm internal dia) of any description set in cement mortar.

M&L 25mm thick cement concrete type B-O, 1:2:4 (12.5mm graded agg ) as in sub base complete all as specified and directed by Engr in Charge.

M&L for Non-skid ceramic tiles, coloured, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:4 complete all as specified and directed by Engr in Charge.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:4 complete all as specified and directed by Engr in Charge.

M&L for Vetrified tiles light shade of 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:4 complete all as specified and directed by Engr in Charge.

M&L chequered cement concrete tiles 30cmx30cmx25cm/ 20cmx 25mm thick,set, jointed & pointed in neat cement slurry in floors with grey cement and pigments over & including 20mm thick screed in cement mortar 1:6

M&L 100mm thick PCC 1:2:4 Type B-2 using 40mm crushed stone aggregate as in flooring finished even and smooth without using extra cement complete all as specified and directed by Engr in Charge.

M&L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone agg as in sub base of floor complete all as specified and directed by Engr in Charge.

M&L 75 mm thick PCC 1:3:6 Type C-1 using 20mm crushed stone aggregate as in plinth protection and finished even and smooth without using extra cement including providing joints not exc. 2.00m in length complete all as specified and directed by Engr in Charge

Bitumastic filling, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, as in plinth protection complete all as specified & directed.

M&L for PCC 1:2:4 Type B-1 using 20mm crushed stone aggregate as in surface channels and drains complete all as specified and directed by Engr in Charge.

Extra forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, mould, mitred/stopped ends etc., complete all as specified and directed by Engr-in-charge.

M&L for Machine cut kota stone slab flooring 595 mm x 595 mm x 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over 20mm thick cement screed bed in CM(1:4) including rubbing and polishing complete all as specified and directed by Engr in Charge.

M&L 1:3:6 type C-1 precast cement concrete (20mm graded stone aggregate) block masonary with solid blocks exc 10 cm in width and not exc 20cm in width and setting in cement mortar 1:6 complete all as specified & directed by Engineer-in-charge.

Providing precast cement concrete solid building blocks or slabs 10cm thick(with plain or interlocking joints as directed) , in wall type C1,1:3:6 using 20mm graded aggregate and setting in mortar 1:6 complete all as specified & directed by Engr in Charge.

M&L for 300 x200 x 6-7mm/450 x300x6-7mm thick glazed coloured ceramic tiles as in skirting / dado incl 10mm thick back coat in CM 1:3 etc. set and jointed in neat cement slurry and pointed in coloured cement with pigment complete all as specified and directed by Engr-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr in Charge.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr in Charge.

M&L for walling of random rubble stone masonry uncourced well bonded bedded and solidly hearted built in CM 1:6 for foundation wall,retaining wall,manholes,tank staging etc. complete all as specified and directed by Engr-in-Charge.

All as per item No 35 above but except stone complete all as specified and directed by Engr-in-Charge.

M&L for providing precast cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in bond stone of retaining walls set in CM 1:6 complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in coping ,surfaces finished even and smooth without using extra cement complete all as specified.

M&L 15mm thick rendering on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement(with water proofing compound) complete all as specified and directed by Engr in Charge.

Supply only Integral waterproofing compound as per manufacturer instructions complete all as specified and directed by Engr in Charge.

M&L two coats of cement base paint on plastered surface including preparation of newly plastered surfaces complete all as specified and directed by Engr in Charge

M&L 10mm thick rendering on brick work or concrete surfaces on internal surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engr in Charge.

M&L for preparation of newly plastered surfaces of walls applying two coat of oil bound distemper over 2mm thick wall putty complete all as specified and directed by Engr in Charge.

M&L for preparation of old surfaces & applying one coat of oil bound distemper on wall complete all as specified and directed by Engr in Charge.

M & L for preparation of old plastered surfaces of wall including brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, and applying one coat of cement based paint complete all as specified and directed.

S&F in repairs 19/20 mm dia curtain rails mild steel chromium plated with fixing brackets, stops, roller etc, complete all as specified and directed.

S&F powder coated GI snap grid of size 605 X 605mm frame work for false ceiling including hangers 2mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long whereever required or tie on structural steel complete all as specified and directed.

S&F Exposed metal frame ceiling with 8mm thick decorative laminated calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mmX600mm grid (frame work for ceiling shall be measured and paid seprately) complete all as specified and directed.

M & L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed by Engineer-In-Charge.

M & L for Solid PVC Wall/ceiling wall Lining consisting of 5mm thick any colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame incl corner & edges complete as per specifications and drawing complete all as specified and as directed by Engineer-In-Charge.

S&F Anodised aluminium frame of doors, windows & ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engr in Charge.

S&F Anodiesed aluminium door shutters, aluminium section weighing 0.55 Kg/m incl. necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos(150mm) in each doors, hinges, anodiesed aluminium snap beading screw etc. complete all as specified and directed by Engr in Charge.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle 100mm (1 no.) complete all as specified and directed by Engr in Charge.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

S&F 4 mm thick Aluminium composite Panel for door including necessary joining cleats, glazing clips, ruber neoprene packing, anodised aluminum snap beading screws etc. complete all as specified and directed by Engr in Charge.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares n. exc 0.5 Sqm, each pane complete all as specified and directed by Engr in Charge.

S&F 35mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed by Engr-in-Charge.

S&F 2nd class hard wood 35 mm thick Glazed and sketon shutters, open rebeated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SS Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkat, complete all as specified and directed by Engr-in-Charge.

S&F solid PVC door frame of size 50 mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, in opening as per specification & drawing, complete all as specified and directed by Engr-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail on either side and as gap insert for top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to this stiles and rails with suitable PVC sheet beading and joined together with solvent cement, S&F in the frame at site as per specification and drawing all as specified in SSR Part-II 2020 section 8, complete all as specified and directed by Engr-in-Charge.

S&F 1.25mm thick pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs,hinges,lock strike plate etc. complete all as specified and directed by Engr-in-Charge.

S&F 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed by Engr in Charge.

S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr in Charge.

S&F 100mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr in Charge.

S & F in repair butt hinges, 100mm medium weight, cold rolled mild steel complete all as specified and directed by Engr in Charge.

Supply only butt hinges, 100mm medium weight, cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame complete all as specified and directed by Engr in Charge.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by Engr in Charge.

Hacking out old broken glass (any thickness) , size, quality or description ) from metal frame including punching or drilling out old glazing pins complete all as specified and directed by Engr in Charge.

S & F in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engr in Charge.

S & F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engr in Charge.

S&F in repair aluminium hat pegs, solid body, 125mm to 175 mm complete all as specified and directed by Engr in Charge.

S&F 150 mm Aluminium handles, cast type, anodised, complete all as specified and directed by Engr-in-Charge.

S&F mild steel 300mm ordinary rat tail rod pattern springs including roller, roller plate, complete all as specified and directed by Engr-in-Charge.

S&F in repair 40mm thick puff insulation panels sandwiched between 0.40mm pre painted galvalume sheet of white from inside & outside complete all as specified and as directed. (Note:- PUF should be density of 40 kg/cum)

S & F Mild steel roof trusses (framed), Trussesd, purlins, crane grantries, rails and framings and heavy bracket framing (Beam,tee, angle, channel or flat sections) confrming to Fe 410-W including welidng cleats,distance pieces etc., complete all as specified and directed.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified & directed by Engr in Charge.

M&L for preparing new or previously untreated steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr in Charge.

M&L one coats of synthetic enamal paint to steel surfaces of any discription not otherwise described over 10cm width or girth preparation of old surfaces complete all as specified and directed by Engr in Charge.

S&F 500 Ltrs capacity, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I, including 20mm ball brass valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed to 20 mm bore steel tube and dismantling existing water tank and removing complete all in repair as specified.

S&F 2000 Ltrs capacity, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I, including 20mm ball brass valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed to 20 mm bore steel tube and dismantling existing water tank and removing complete all in repair as specified.

M&L for preparing new or previously untreated surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S & F 15 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor in repairs complete all as specified and directed by Engr in Charge.

Fixing only 15 mm water tubes, any grade, to walls and ceilings or laying in floors using GI tubing retrieved from taking down of tubing complete all as specified and directed by Engr in Charge.

S&F 20 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor in repairs complete all as specified and directed by Engr in Charge.

Fixing only 20 mm water tubes, any grade, to walls and ceilings or laying in using GI tubing retrieved from taking down of tubing floors complete all as specified and directed by Engr in Charge.

S&F in repairs bib taps, cast copper alloy, chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm bore steel tube complete all as specified and directed by Engr in Charge.

S&F in repairs 15mm bore stop valve/angle valve cast copper alloy chromium plated fancy type screwed down, high pressure, with crutch or butter fly handles complete all as specified and directed by Engr in Charge.

Supply & fixing in repairs vitreous china wash basin, white, flat back of size 600mm x 400mm including 32mm dia PVC flush pipe with coupling and set of brackets including 15mm bore pillar tap fancy type cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule incl PVC connections 15mm size with PTMT nuts of legth 450mm complete all as specified and directed by Engineer-in-Charge.

S &F PVC valveless syphonic action type low level flushing cistern white of capacity 10 ltrs with inlet valve float and fixed to water closet with PVC flushing pipe 32mm dia complete all as specfied and directed by Engr in Charge

S&F in repairs vitreous china squating pan 'orissa patter' size 580mm x 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap concrete and to flushing pipe, anti syphonage pipe etc. complete inlcuding making good to floor complete all as specified and directed by Engr in Charge

S&F in repairs vitreous china wash down water closet pan (pedestal pattern) white, including flush pipe of polyethylene of low or high density or PVC 32mm dia, plastic water closet seat closed pattern with cover and hinging device and trap with connection complete all as specified and directed by Engr in Charge

S & F chromium plated jet for EWC complete all as specified and directed by Engr in Charge

S &F in repairs vitreous china urinal, half stall type, white with 32mm bore PVC waste pipe of length 900mm to 1200mm and including urinal spreader of PTMT any colour for fixing with 15mm dia pipe including connnection to flushing pipe and outgoing pipes with 32mm bore PVC waste pipe or length 900 mm to 1200mm complete all as specified and directed by Engr in Charge.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm in repairs complete all as specified and directed by Engr in Charge.

S & F in repair chromium plated shower rose 125mm size with or without swivel joint any size incl fixing to steel pipe or union complete all as specified and directed.

S&F in repairs CP tubular towel rail, 20 mm dia. 60 cm long between flanges complete all as specified & directed by Engineer-in-charge.

S&F in repairs Soap dish, cast copper alloy, chromium plated with screws complete all as specified & directed by Engineer-in-charge.

S&F 110 mm bore, PVC (SWR) pipes single socketed/ elbow/ tee, in any length with rubber ring joints, laid in trenches or in floors inclusive dismantling old one complete all as specified and directed by Engr in Charge.

S&F in repairs 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors after dismantling old one complete all as specified and directed by Engr in Charge.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engr in Charge.

S&F for 110mm PVC (SWR) bends complete all as specified & directed by Engineer-in-charge.

S& F for 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified & directed by Engineer-in-charge.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm incl 40mm Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm-45gms/40mm-60 gms)& PVC waste pipe complete all as specified.

M & L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified & directed by Engineer-in-charge.

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone agg as in cover slab and like axcept set in cement mortor 1:4 complete incl necessary form work all as specified.

M&L mild steel TMT bars 6-8mm dia bar cut to length, bent to shape required including cranking, bending spirally for hoping for fencing posts and binding with mild steel wire ( annealed) not less than 0.9 mm dia all as specified.

Excavation in trenches not exc 1.5 Mtr wide and not exc 1.5 Mtr in depth for pipe line drains, foundations of sewage lines or manholes , taking up/taking down of cables and like and getting out in soft/loose soil complete alla s specified and as directed by Engineer - in - Charge.

Returning, filling in incl spreading ,levelling watering and well ramming in layer n exc 25cm in soil each layer complete all as specified and directed by Engineer - in - Charge.

Removing excavated surplus material to a distance n exc 50m and depositing where directed at level n. exc 1.5m above the starting point in any type of soil complete all as specified and directed by Engineer - in - Charge.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone agg as in bed to drain pipe, incl packing under and haunching against the sides of pipe 150mm bore after they are laid and tested complete all as specified & directed by Engineer-in-charge.

M&L 150mm internal dia reinforced concerete pipes, class NP2, laid and jointed complete with collars and jointed complete all as specified & directed by Engineer-in-charge.

M&L three coats of white wash on plastered surface including preparation of newly plastered surfaces complete all as specified & directed by Engineer-in-charge.

Demolition of septic tank and soakage well (constructed by engineers unit) including desilting/desludging the septic tanks / soakage wells etc. by manual labour or mechanical means and removing the sludge in liquid or semi-liquid state out side defence land complete all as specified and directed.

Construction of 20 users Septic tank to carry sewage and sullage water, with RCC (1:1.5:3), B-1 Roof Slab all as per shown in Drg No. STD 1320 (C) Sheet 1/3 to 3/3 with following specification. Excavation in any type of soil, precast cement concrete (20mm graded stone aggregate) C-1 block masonary in Walls , Base Slab , Baffle walls of RCC (1:1.5:3), Vent shaft , manhole openings with cover connection Complete. Note:- (i) precast cement concrete (20mm graded stone aggregate) C-1 block masonary in Walls as 700/600/500/400mm in lieu of 690/575/460/345mm respectively wherever shown in drawing. (ii) Stone boulders filling will be done in lieu of brick bats filling in lieu brick bats where ever shown in drawings.

Construction of Soak well 1.80m dia and 3.0m effective depth as specified on STD 1173(C) sheet 1R/2 with following specification free board as per site requirement in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of precast cement concrete (20mm graded stone aggregate) block masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with Stone boulders of size, complete all as specified on STD 1173(C) sheet 1R/2. Note:- (i) precast cement concrete (20mm graded stone aggregate) C-1 block masonary in Walls as 700/600/500/400mm in lieu of 690/575/460/345mm respectively wherever shown in drawing. (ii) Stone boulders filling will be done in lieu of brick bats filling in lieu brick bats where ever shown in drawings.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, excluding fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engr in Charge.

M&L for point wiring using approved colour coding as per IS by using FRLS PVC insulated 1.5 Sqmm multistranded,1100 volt grade copper conductor cable unsheathed type, alongwith 1.5 Sqmm FRLS PVC insulated stranded copper conductor cable for continous earthing in & incl casing capping point wiring with accessories having ISI mark for one light/fan/bell point/5 amp indep/power point/same board controlled by one switch complete all as specified and directed.

All as per item No 112 here-in-before but for one multipin socket outlet 5 Amp but using 2x 1.5 + 1 x 1.5 sqmm multistranded FRLS copper cable on the independent board

All as per item No 112 here-in-before but for one multipin socket outlet 5 Amp on the same board with other switches

All as per item No 112 here-in-before but for one multipin socket outlet 15 Amp, but using 2 x2.5 +1 x 2.5 sqmm multistranded FRLS copper cable, independent board

S&F in replacement of switch piano type 5 Amp, 230 Volt, flush type single pole one way complete all as specified and directed.

S&F in replacement of socket outlet multipin 5 Amp 230 Volt flush type complete all as specified and directed.

S&F in replacement of switch piano type 15 Amp, 230 Volt, flush type single pole one way complete all as specified and directed.

S&F in replacement of socket outlet multi pin 15 Amp 230 Volt flush type complete all as specified and directed.

S&F In replacement of for Lamp holder, PVC/Polycarbonate type with back plate suitable for Angle/batten fittings complete all as specified and directed

S&F of rechargeable led bulb minimum 4 Hrs Battery backup 9 Watt B-22 Base complete all as specified and directed.

S&F in replacement of Ceiling rose, 3 terminal, PVC isolated body complete all as specified and directed

S&F in replacement of LED light fitting 20W, 220 volt AC, having colour temperature daylight (6500K), Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in replacement LED light fitting 1x10W/1X12W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

S & F including flushing in wall MCB distribution board vertical TPN 4 way 415 volt AC double door sheet with bus bar neutral earth bar including provision of MCB TPN 63 amp conforming to IP 43 as incomer complete all as specified and directed.

S&F MCB TPN 63 amp 415 volt with bearing capacity of 16 KA complete all as specified and directed.

S&F in replacement of sheet metal enclosure double door distribution board single pole and neutral, 12 way 240 volt with 100 amps rated bus bar complete with bus and neutral link complete all as specified and directed.

S&F in replacement of MCB 6 to 32 amp rating 240V, 10KA 'B' curve, Single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F in replacement of MCB SPN 40 amp2 amp rating 240V, 10KA 'B' curve, Single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply & laying LT UG XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 Volts grade cross-sectional area 10 sqmm 4 core as per IS specification laid through GI pipe/on floor/wall complete all as specified and directed

Supply and laying of GI pipe light galvanized with all fitting laid in trenches for cable proctection of 50 mm bore all as specified and directed.

M&L in replacement of Earthing complete with galvanised steel earth plate electrode 600×600×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as directed.

Supply and fixing Building LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. all as specified and directed.

Supply, laying and drawing in and including 20 mm dia casing caping including cutting of chases for laying conduit making good the surfaces as per existing surfaces or as directed on walls 02 runs of IC x 6.00 sqmm (Main Cable and neutral) and one run of IC x 6 sqmm (as earth wire) of stranded copper conductor PVC insulated unsheathed cables of 1100 volts grade conforing to IS : 694 of 1990 complete including connection all as specified and directed. (From AC Box to DB) (Note:- Three run of 6 sqmm cable & 1 run of 20mm PVC casing caping shall be measured as one length.)

Supply and fixing of exhaust fan, steel body AC single Phase 230V of size 450m sweep heavy duty 1400 RPM with, blades, and frame and louvers complete all as specified and directed.

M&L for sand filling floors or in foundation including watering and compansation.

M&L for old size bricks common burnt clay building bricks sub class B designation 75

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with servicevalue 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed

S & F in replacement of stepped type electronic fan regulator flush type, complete all as specified and directed

S&F for fixing of GI pipe (light grade) bracket of 40mm bore size of 1.2 mtr long bent to shape for fixing of LED street light fittings and fixing to pole, walls etc including fixing of clamp, nut, bolt etc as specified and directed.

S&F single pole and neutral enclosure with a two pin plug and socket complete with one single pole MCB 32 Amp complete all as specified and directed.

S&F highly BEE star rated energy efficient water heater storage type, electric supplied and installed complete incl all,NRV, PVC connections pipe capacity 25 Litres all as directed By Engr-in-charge

Taking down ceiling fan, ceiling cable end, dismantling blades and removing fan and deposited to MES Yard blades to store complete all as specified and directed.

M&L for rewinding of ceiling fans of any type and make complete with super enamelled copper wire (HTP) in the workshop wire with appropriate gauge suiatble for existing make including necessary lathingmon shaft, capacitor,Bearing, both sides of rewinding covered with high quality varnish, replacement of ball bearing of SKF/NBC make and provisions of new nuts and pins for 1200/1400 mm sweep including taking out old burnt wind of copper/aluminium complete all as specified and directed.

Schedule of Credit

Pankaj Builders (BID ID -3413882)

M/S J.S.ENTERPRISES (BID ID -3411857)

M/S SHIV NATH ENTERPRISES (BID ID -3407547)

M/S Shamsher Negi Dewa (BID ID -3409726)