REPAIRS TO ROAD, CULVERT, FOOTPATH AND ROAD SIDE FURNITURE AT ZONE-II UNDER GE BRICHGUNJ, SRI VIJAYA PURAM

Material and labour for repair to potholes any depth, not exceeding 1sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in roads, paths etc. cutting around edges to at least 25 mm in depth making good by applying tack coat with bituminous primer @ 5 kg per 10 Sqm, putting in premixed bituminus mecadum , well rammed and sealed with binder for thin bituminous carpet (2cm thick) well rammed and sealed with premixed and sand seal coat(6.8kg of binder with 0.06 cum of sand ) again well rammed (including supply of premixed binder and sand ), depth of potholes n exc 30mm

Material and labour for repair to potholes exceeding not exceeding 1.0sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in roads, paths etc. cutting around edges to at least 40mm in depth making good by applying tack coat @ 5kg per 10 sqm, putting in premixed bitumenous macadam well rammed and sealed with binder 9.80 kg per 10sqm .blinded with 0.09cum of stone chippings, 6.3mm size and again well rammed (including supply of premixed macadam,binder and chippings ), depth of potholes exc 30mm

Scarifying or picking gravelled , macadam or bituminus macadam surfaces in area not exceeding 400 Sqm and exceeding 50mm and n exc 100mm depth including removing to a distance not exceeding 50m complete all as specified and as directed by the Engineer -in- charge.

Material and labour for one layer 75cm thick (compacted thickness 75mm) WBM, with coarse aggregates of grading 2 (63 to 40mm size) ,granite trap or basalt spread, rolled and consolidated to gradient and camber required

Preparing new WBM surface by brushing with wire brushes for removing caked mud etc sweeping with broom and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc by cleaning the WBM surface with power compressor and applying evenly priming/tack coat with bituminuos primer of VG-10 grade paving bitumen @ 10 Kg / X Sqm complete all as specified and as directed by Engineer-In-Charge.

M&L for preparing old black top surface by brushing with wire brushes for removing craked mud etc, sweeping with brroms with finaly fanning the clean surface with gunny bags to remove all loose dirt etc and applying evenly at a tack coat with and including paving bitumen of VG-10 at the rate of 5 Kg per 10 sqm of surface complete all as specified.

M&L, bituminous premix aspaltic semi dense concrete, 40mm consolidated thickness with 5.5% binder paving bitumen VG-30 content by weight of total mix, by hot process and laid by meachanical paver, rolled and compacted to required camber and gradient complete all as specified and directed.

M&L for premix bituminus macadam (consolidated thickness 75mm or less ) , with binder (Paving bitumen of VG -30) content at 4% by weight of total mix , laid rolled and compacted with 8 to 12 tonne power roller to required gradient and camber using mechanical paver complete all as specified.

S&F solar cat eye aluminum alloy shell(100% water proofing design according to 65) ofsize 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/0.3 watt one NI-ed rechargeable battery (1.2V/1600MA) consisting of super bright LED with10,000 to 18,000 mcd completed as per manufacturers instructions etc.complete all as specified and as directed.

M & L for Road Painting lines, dashes, arrows, letters,etc. on roads pavements and the like n exc 10cm wide with road marking paint, white or golden yellow as required at site complete all as specified and as directed by Engr-in-charge.

S&F in repairs Poly Carbonate Convex Mirror outdoor type 1000mm dia with , Reflective Pole mounted and fixed to 80mm bore Medium Grade MS Pipe of required length complete and embedded in PCC 1:3:6, Type C1, including necessary earth work required for post holes complete all as specified.

S&F in repairs Poly Carbonate Convex Mirror outdoor type 1200mm dia with , Reflective Pole mounted and fixed to 80mm bore Medium Grade MS Pipe of required length complete and embedded in PCC 1:3:6, Type C1, including necessary earth work required for post holes complete all as specified.

S&F in repairs Road Stud , Two way reflective type, ABS body with retro reflective panel of Amber, Red or white colour complete all as specified and as directed.

Demolition of PCC block masonry built in cement mortar all as specified and as directed.

Demolition of cement concrete of any description and in any position complete all as specified and as directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and as directed by Engineer-in-Charge.

M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade over 50mm thick sand cushion all as specified and as directed by Engg-in-charge.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate in Cement concrete in foundations, filling and mass concrete completes all as specified & directed.

M & L precast cement concrete block masonry (1:3:6) type C1 (20mm graded stone aggregate) masonry with solid block exc10cm in width and setting in CM 1:6 etc complete all as specified and directed.

M&L for PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in coping etc , rounded or chamfered on edges all as directed

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work/block masonry or concrete surfaces finished even & smooth without using extra cement complete all as directed.

Extra for forming fair finished drain or channel over 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc.

M&L for Precast RCC Type B1, 1:2:4 (20mm graded stone aggregate) as in cover slabs set in cement mortar 1:6 etc

M&L mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips

Please Enable Macros to View BoQ information