CONSTRUCTION OF 100 BEDDED CRITICAL CARE UNIT BUILDING AT GOVERNMENT ERODE MEDICAL COLLEGE AND HOSPITAL AT PERUNDURAI IN ERODE DISTRICT

Amount

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering and bailing out water wherever necessary and refilling the sides of foundation with excavated earth in layers not more than 15cm thick wall rammed consolidated depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and refilling the sides of foundation with excavated earth in layers not more than 15cm thick wall rammed consolidated depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Cement Concrete 1:5:10 (One Cement, Five M-sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and filling in foundation, basement, etc with filling M-sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and FILLING GRAVEL in 'foundation and basement M-sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Refilling in basement with excavated earth other than M-sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Cement Concrete 1:5:10 (One cement, Five M-sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Brick work in Cement Mortar 1:5 (one cement and Five M-sand) using best quality Fly ash bricks of size 23x11x7cm for the following including curing etc.,complete complying with standard specification.

For Foundation and Basement

For Ground Floor

Brick work in Cement Mortar 1:6 (one cement and Six M-sand) using best quality Fly ash bricks of size 23x11x7cm for the following including curing etc.,complete complying with standard specification.

In Ground floor

In First floor

In Second floor

In Third floor

In Fourth Floor

Brick partition walls of 11.00cm thickness using best quality Fly Ash Bricks of size 23 x 11 x 7 cm in Cement Mortar 1:3 (One Cement and Three M-Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

In Ground Floor

In First Floor

In Second Floor

Damp proof course with Cement Mortar 1:4 (One Cement and Four M-sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc. complete complying with standard specification.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kg/m3 and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

For Super Structure in Ground Floor

For Super Structure in First Floor

For Super Structure in Second Floor

For Super Structure in Third Floor

For Super Structure in Fourth Floor

Cement Concrete 1:3:6 (One Cement, Three M-sand and Six broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three Sand and Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

For third Floor

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

50mm thick precast slab

75mm thick slab

Supplying, fabricating and placing in position MILD STEEL / RIBBED TOR STEEL grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. [Contractor has to make his own arrangements for the supply of steel and binding wire]

Plain Cement Concrete 1:2:4 (one cement, two M-sand and four hard broken stone jelly) using 10 -20 mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers. (In Foundation and Basement)

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

In Ground Floor

In First Floor

In Second Floor

In Third Floor

In Fourth Floor

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three M- Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best quality Double Charged Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M-sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Providing full nosing to the steps or platforms to the Granite slab of 20mm thick including neat finishing, polishing, cost of powder, tools etc as directed by the departmental officers

Paving the floor with best approved quality Using Fine polished Kota Stone Slab below 600 x 600 of 20mm size with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification

Flooring with Self design Joint free rectified Ceramic Tiles of size 305 x 305 x 8mm laid over 20mm thick cement mortar 1 :3 (One cement and Tree M-sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary , laying in position and and pointed with the Epoxy chemical filling and necessary spacer at the rate of 0.3kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK or Equivalent which has to be got approved by executive Engineer before use on works)

Dadooing walls with 300x450x8mm best approved quality, white / colour glazed tiles set in Cement Mortar 1:2 (One Cement and Two M-sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. /sq.mneatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.(The make, brand and colour should be got approved by the Executive Engineer before use on work)

Dadooing walls with 600x600x8mm best approved quality, white / colour glazed tiles set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. /sq.mneatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Dadooing with granite tiles of Jet black of suitable sizes with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.

Providing Polymer Coating (Water Proof Coating) for sunken Portion of toilet with following specification and the surface shall be cleaned to remove all dust, foreign, matters lose materials or any other deposits of contamination by rubbing with wire brush.Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred throughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes 160mm dia having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

One floor

Three Floor

Supplying wrought fixing Ornamental Teakwood entrance door as per the drawing and designs approved by the departmental officers. The size of the opening is 2.10X 2.40. The outer frame of the door is 150mmx125mm teakwood. The main door shutter opening size is 1.80 X 2.03m. The main door should be double leaves and each door shutter fully panelled. The door panells shall be of 50mm thick teakwood planks with ornamental designs approved by the Executive Engineer. The Lock rail and bottom shall be of 200 x 50mm tk teakwood, top rail 230x50mm tk teakwood. The door frames and shutters shall be given of cost of best approved quality melamine finish. The rate inclusive of cost of approved quality teakwood, 10mm thick designed toughedned glass Special type Heavy Brass Aldrop 300mm X 20mm. Special type heavy Brass tower bolt 300mm Length. Special type heavy Brass tower bolt 250mm Length. The cost includes cost of material, labour charges, conveyance charges, fixing charges, designing charges and glass design charges, electricity charges and all other incidental charges., etc. All materials should be got approved by the Executive Engineer before use on works.

supplying and fixing of Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using 304 Grade Stainless Steel Plate of 1.6mm thick)16 gauge of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc., The rate in inclusive of bottom thehold fasts and provision to aldrip tower bolt hinges and lock plate etc,with one coat of zinc chnomate yellow primer and filling the inside hallow portion with cement concrete 1:2:4 using 20mm HBG stone jelly etc,complete complying with standard specification.

Supplying and fixing Solid core Particle board flush shutter of nominal thick of 35 mm with Teak ply on both sides and with T.W. lipping alround conforming to IS 2302 including supplying and fixing cost of wind appliances and furniture fittings such as 1no .300 x 12 mm aluminium tower bolt 2 nos. 200x12 mm aluminium tower bolts 1no. 250 x 16 mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete as directed by the departmental officers. Single leaf

Supplying and fixing Solid core Particle board flush shutter of nominal thick of 35 mm with Teak ply on both sides and with T.W. lipping alround conforming to IS 2302 including supplying and fixing cost of wind appliances and furniture fittings such as 1no .300 x 12 mm aluminium tower bolt 2 nos. 200x12 mm aluminium tower bolts 1no. 250 x 16 mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete as directed by the departmental officers. Double leaf

Supply & fixing of WPC (Wood Polymer Composite) Frame extruded with size 75mm x 50mm. The single core door made of rigid WPC compound with minimum Bulk Density of 900 KG/ Cub.Mt. & shore hardness of 55. Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/ Cub.Mt. & shore hardness of 55. For the aesthetic appearance, the door shall be a printed digitally on one side of the shutter and the design is as decided by the Engineer in-Charge of the department. The WPC door shall be fixed onto the WPC frame with 3 Nos of 5” SS Hinges and the door shall have 2 towerbolt on one side and 1 towerbolt or aldrop on other side for locking system and 2 numbers of handle on the either side of the door shutter, all made of aluminium.

Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/ Cub.Mt. & shore hardness of 55. The door shall be a plain matt board as decided by the Engineer in-Charge of the department. The WPC door shall be fixed onto the Aluminium “G” type channel with Wheel and the door shall have 2 Hooks in SS, 2 Handles 4” in SS.(Sliding door)

Supplying, fabricating and fixing in position factory made Stainless Steel Flush Door Shutter 35mm thick using SS 304 Grade 1.6 mm thick, Stainless Sheets on both sides (Equivalent to IS 6911-04 Cr. 19, Ni 9) minimum 8-8.5% nickel and 18% chromium sourced from original stainless steel manufacturer with view panel size 30mm x 45mm made up of 6mm thick clear toughened glass fitted with double side adhesive tape and finished with dowconing silicon sealant, floor pring for each shutter, consealed tower bolt, suitable stainless steel locking arrangement and other necessary furniture fittings of approved quality. The vertical styles and other frame members and cross stiffeners shall be of same quality stainless steel box section of suitable size and thickness with proper core material as prescribed by the Departmental Officers.

Providing and fixing of 1.2mm thick Lead Lining Door for X-Ray Rooms, Scanning Rooms with Mild Steel Door Frames 105mm x 57mm X 18 G and 12 G x 50mm Shutter made of GI with PWG finish and honey wool insulations with SS 101mm x 75mm x 3mm SS 304 Ball Bearings Butt Hinges, Mortice Sash Lock ML 100A, 50mm BS, 85mm centre, CL 207 : Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make), Heavy Duty Door Closer, Frames fixed wih walls using Mortice Sash Lock ML 100A, 50mm BS, 85mm centre CL207: Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make) all neccesary accessories and fittings as per the required and as per the approval for the Department Officer

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.

Manufacturing supplying and fixing of STEEL DOOR Single leaf with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia. Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing.The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supplying and fixing M.S. Grill of approved design for open courtyard, grill, grill works to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification and as directed by departmental Officer

Bed Head Panel of size 1m, length, height 0-0.30cm and depth of 4". The aluminium powder coated with requirement colour for provisioin points of O2-2 No. Air 1 No. Vaccum 1 No. with double electrical socket with switch 2 Nos. with 2 set with IV - bottle holder fixing to the wall hanging including monitor stand etc., complete.

Supplying and fixing of SS False Ceiling

Supplying and fixing fine polished cuddapah slab of 40mm thickthickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct by the Departmental Officers.

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work..

Supplying and fixing of SS Wall Cladding

Supplying and laying of Rubber moulded Hydraulic pressed Paver block of 63mm thk. Over a base layer of sand filling incl. Cost of materials laying and Labour charges etc.,

Plastering with Cement Mortar 1:5 (One cement and Five P-sand), 12mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P-Sand) 10mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:3 (One Cement and Three P-Sand) 12mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:4 (One Cement and Four Sand) 20mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc., complete complying with standard s conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Providing Wall Putty including labour charges etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed Interior plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Providing expansion joint in RCC floor slab for 12.5mm width using polysulphide as sealent on the top and bottom for a depth of 7.5mm each and packing the inner space using compressible non-absorbent filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealent with necessary spatula etc., complete complying with standard specifications and as directed

Providing expansion joint 12.5mm width in RCC roof slabs between RCC twin beams using PVC water bar of 150mm wide centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with suitable non-absorbent flexible and well compressible filler materials of approved quality and covering the top surface with GI sheet 30cm wide and 1.6mm thick using phill plugs, GI screws, limpet cup washers, bitumen washers, etc., complete complying with standard specifications and as directed

Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed.

Supplying and erecting pull and push type (electrically operated exceeding 12 Sq.m area) rolling shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc.,

Supplying, laying and jointing CPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

25 mm dia CPVC Pipe

Supplying CPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements

25 mm dia CPVC Elbow

25 mm dia CPVC TEE

25 mm dia CPVC Union

25 mm dia CPVC Nipple

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.(Internal Water Supply Above Ground Level)

25 mm dia UPVC Pipe

32 mm dia UPVC Pipe

40 mm dia UPVC Pipe

50 mm dia UPVC Pipe

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.(External Water Supply Below Ground Level)

40mm dia

Supplying UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements

Union 25mm dia

Union 32mm dia

Union 40mm dia

Union 50mm dia

25mm dia UPVC Elbow

32mm dia UPVC Elbow

40mm dia UPVC Elbow

50mm dia UPVC Elbow

25mm dia UPVC TEE

32mm dia UPVC TEE

40mm dia UPVC TEE

50mm dia UPVC TEE

32 x 25 mm dia Reducer

25 x 20 mm dia Reducer

20 x 15 mm dia Reducer

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

25mm dia GM gate valve

32mm dia GM gate valve

40mm dia GM gate valve

50mm dia GM gate valve

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC low level flushing tank with a pair of CI brackets fixed on the wall, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supply and fixing in position of best Indian make colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position best quality and approved make Indian made colour glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position best quality Granite sink of 600 x 600 x 200mm size and complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing in position CP shower rose with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position 15mm dia brass of following type CP tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

screw down tap

Swan Neck Tap

Supplying, laying and jointing glazed stoneware pipes of 110mm dia of approved best quality with spigot and socket ends (in reverse direction) in dry condition and laid in loose joints (i.e.) without cement and spun yarn, so that the waste water can be drained to the trenches already available, excluding cost of earth work excavation, cost of re-filling with sand / earth, but including laying the pipe in true alignment and gradient and conducting required water supply test for draining with necessary tools and plants, etc., complete complying with standard specifications.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia PVC soil / waste pipe

110mm dia PVC soil / waste pipe

160mm dia PVC soil / waste pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

75mm dia Elbow

75mm dia TEE

75mm dia TEE with Single door

75mm dia Bend

110mm dia Elbow

110mm dia TEE

110mm dia TEE with Single door

110mm dia Bend

Supplying and fixing position PVC Nahani Trap / Floor Trap of the 100 x 75mm sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works.

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supplying and filling 20mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Supplying and filling 40mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Drilling of Borewell in sedimentary strata of clay and sand stone shale pebbles bolders etc., By first taking a pilot bore of 150mm dia and then enlarging to the required dia by direct or reverse rotary mud circulation method using rotary rigs, fuel labour and drilling bentonite and water required for dirlling at site. (As per TWAD rate)

upto 150m

Supply of 6" dia PVC casing pipe of best approved quality etc complete as directed by the departmental officers. The pipe should got approved by the Executive Engineer before use on works

Supplying and fixing of suitable PVC endcap (6kg/cm2) for 7" dia borewell of best quality with ISI mark

Supply and delivery Of 3Core copper conductor Flat Cable (4Sq.mm) confirming to IS 694/1990 with ISI marking sutiable for Submersible Pumpset etc., Complete

Supply and fixing of 40mm dia UPVC (Un-Plasticized Polyvinyl Chloride) Pipe (Higher pressure rating with higher pipe thickness) Standard Dimension Ratio of best and approved quality for delivery cum support pipe for submersible motor instal inside borewell etc., complete as directed by the departmental officers.

Supplying and fixing of Nylon rope for submersible motor of approved quality in etc.,complete complying with standard specifications.

Supplying and fixing erecting 5 HP ( DECCAN MAKE) ISI make bore well SUBMERSIBLE PUMPSET with required accassories for the 5HP ISI make3 phase electricmotar 2900rpm , 400/S.S. shaft cable of discharging 100 to 200 LPM against a total Head of 135m to 100m with ISI mark and an outlet of 50mm and suitable for 150mm dia bore well including supplying and fixing M.S. fabricated wall mounting Pannel board with internal wiring as per I.E. rules and necessary locking arrangements with suitable cutler and hammer type bush button automatic 10 HP texvel DOL starter - 1 no, suitable 15 Amp, TPIC switch, 0 to 500 v Voltmeter, 0 to 20 Amps Ammeeter, single phase preventer. pilot lamps with 3 bulps to indicate power supply and 50mm dia GI couplying - 2 nos, M. S. clamps - 2 nos, 2.5 Sq mm wire 3 core copper flat submergible cable, including Conveyance and Erection charges including required G. I. pecials, MR Tape Electrical connection charges., delivery pipe connection charges and other plumbing works including hire charges for Chain pully, tripod and other tools and trial run for three days etc., including labour charges complete complying as directed by the departmental officers.

Supplying and fixing wall mounting of Panel board with following accessories a.Suitable DOL type push botton automatic starter etc., complete.(3 phase panel board including labour charges)

Supplying and erecting 2 H.P monoblock with ISI mark with necessary accessories (motor should be got approved by Executive Engineer before use onworks) complete complying with standard specification.

Supplying and fixing of PVC ready made HDPE water storage tanks having 1000 litre capacity made of PVC matertials including necessary provision for conveying, jointing delivery line etc.

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Supplying and erecting in position of 250 liters capacity Industrial Model Reverse Osmosis Water-cum- Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No. Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact

Supplying and fixing in position of SS Sink of size 1200 x 550 x 180mm including fixing the sink in position and testing for leakages etc., complete complying with standard specifications [The sink and specials should be got approved by the Executive Engineer before use on works]

CURTAIN WORK Supplying and laying polyester, washable and stainfree cloth (Bio-Active fabric washable germfreesuitable for dialysis room) curtain system with maximum curtain cloth height 230cm (top 30cm white colour and 200cm light blue colour as per approval) stitching with stiffener tape, pleats, ironing and laying around Each bed using sliding wheels two nylon rollers, nylon axil and tangle free nylon swivel stem with chrome-plated steel hook, curtain track should be supported in roof using 20x20mm, 2mm thick sized aluminium tubes same spec with end caps in two sides using all necessary fittings. as per the direction of engineer in charge including conveyance to site, laying in line and level, sealing all cutting in false ceiling with powder coated MS cup, all leads and lifts including all labour charges etc. complete.(unpleated length of the cloth measurement will be considered for payment also the bottom and top folding will not be considered in cloth measurement)/ supplying and fixing powder coated 20mm dia. GI round tube hanging support of required length(app. length 1.10m) one end fixing from slab by using 6mm dia expansion bolt at a distance not more than 2m, c/c down end fixed to powder coated aluminium channel frame x 20mm x 1mm thick section by using SS screw as per the direction of engineer in charge including conveyance

Supplying, fabricating and fixing in position of Netlon Arrangement with Aluminium frame and SS mesh with shutter arrangement to the sizes 30mm x 13mm, wire diameter 027 Kg/m with necessary accessories such as best quality runner, lock, including cost of all materials, labour power consumption required for fabrication, drilling holes in necessary wall wherever necessary with power drills and made same to original condition after fixing.

Supplying and fixing polycarbonate sheet of 6mm thick and steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling wht rotating wheel to open and close the valve including MS flange of table 'E' bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, installation of Fire fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20 mm dia ball valve and open and close spray nozzie, warm clip, etc., as per the standard pattern of nay reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doiing the dismantled portions to its original condition wherever found necessary., etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire fighting application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. (MAKE: OMEX/KARTAR/LIFE GUARD/SAFE GUARD/EQUIVALENT

Supply of Fire fighting Application Application MS Hose Box to keep two number of hoses and 1 no. of branch pipe with nozzie having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, Shellac etc.,as per standard methods and including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.(Make: OMEX/KARTAR/SAFE GUARD/EQUIVALENT.

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1500mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1500mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.

Supply, erection, testing and commissioning of following MS 'C' Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10kg /sq.cm including necessary fittings like MS flange of table 'E' elbows, reducers, gaskets, bolt, nuts wth washerr & joints as per standard method of arc welding, including one coat of metal primer and two coat of Post Officer Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL/ EQUIVALENT.

200 mm dia ( Pump Room)

150 mm dia (Pump Room, Yard Hydrant, wet riser)

100 mm dia (Pump Room, Terrace, Wet riser, Yard)

80 mm dia (Yard hydrant stand pipe, Pump room)

65 mm dia (Ground Floor to 5th Floor corridor sprinkler)

50 mm dia (Pump Room, Drain, Ground Floor to 5th Floor sprinkler branch in to each floor rooms / wards)

25 mm dia (Ground Floor to 5th Floor sprinkler branch in to each floor rooms / wards)

Wrapping and Coating Anti-Corrosive Treatment for the following under ground MS pipe having one coat of anti-corrosive metal primer, one layer of asphalt tar tape wound over the MS Pipe as per standard methods as per standard specification and as directed by the Departmental Officers.

Supply, erection testing and commissioning of following sizes of Heavy Duty Foot Valve including all accessories, such as MS flange of table 'E' gaskets, bolts & nuts etc., installed at end of 150/200mm dia suction pipe line at sump i including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT.

200mm dia (Pump Room)

100mm dia (Pump Room)

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table 'E' gaskets, bolts & nuts including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT.

150mm dia (Pump Room, Terrace, yard hydrant)

100mm dia (Pump Room, Wet Riser, terrace)

65mm dia (All floor corridor)

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead, tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312. including conveyance, all incidental charges, necessary scaffolding and re-doing dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

150 mm dia (Pump Room, GF Yard Hydrant Fire Inlet, Terrace)

100 mm dia (Pump Room, Terrace)

Supply, erection, testing and commissioning of Gun metal Gate valve of size 50mm dia including necessary MS flange of table ‘E’ gaskets, blots & nuts, etc. installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. Make:LEADER/EQUIVALENT.

Supply, erection, testing and commissioning of Gun metal non-return valve of size 50mm dia including necessary MS flange of table ‘E’ gaskets, bolts & nuts, etc., installed at pump house delivery line for the purpose of priming to suction line so that to control one way including conveying, fixing and incidental charges etc complete as per standard specification and as directed by the departmental officers, Make: LEADER/ EQUIVALENT

Priming tank mounted with the supporting arrangement fabricated using MS angle for the height of 3.00 mtrs from the floor level, inlet, outlet, and drain arrangements inside the fire fighting pump room as directed by the department officers

Supply and laying of following sizes of armouredAluminium/ Copper cables for electrical motor. control Panel, Pressure switch, jockey motor etc. all incidental charges necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc. Make:POLYCAB/ PARACON/ FINLOEX/ EQUIVALENT

3 cores 185sqmm armoured aluminium cable (Pump Room)

3 core 10 sqmm armoured copper cable (Pump Room)

10core 2.5 sqmm armoured copper cable (Pump Room)

2 core 2.5 sqmm armoured copper cable (Pump Room)

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specifcation and as directed by the Departmental Officers.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14kg. Range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe ling in pump house to read the developing pressure including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motro including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supply, Installation, Testing and commissioning of Diesel engine driven main Fire Pump suitable for automatic operation and consisting of following complete in all respects as required.End suction, top discharge centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5Kg per sq cm at highest and the farthest at specified flow of 2280 LPM at 70 mtrs head conforming to IS 1520. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts 24 volts electric starting equipment like self Motor, Dynamo, Solenoid switches etc.110 ltrs capacity Diesel tank mounted over stand fabricated using 25mmx25mmx6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre filter, after filter etc.Exhaust system having flexible metallic muffler, 100mm dia MS heavy pipe extended upto 1m. Outside pump house duly insulated with 50mm thick glass wool with 1.00mm thick aluminium sheet cladding, residential silencer with necessary MS support arrangements from wall or ceiling as per site condition.Dash Board consisting the Instruments like Temperature Gauge, Galvano type DC Ammeter, Lub. oil Pressure Gauge , Ignition switch, Emergency Stop and all other protection equipment, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc as required.12 V / 24 V, storage battery, maintenance free tape, 180 AH rating. M.S fabricated common base plate, coupling guard, foundation bolts etc as required.Positioning the Pump over cement concrete foundation using suitable size Anti Vibration mounting arrangements.All works including conveying, fixing and incidental charges etc complete as per standard specification and as directed by the departmental officers. Make: KIRLOSKAR/ EQUIVALENT

Supply erection testing and commissioning of fire fighting application horizontal centrifugal type pump rated for 2850 LPM at 70 mtrs head with electrical motor of 60 HP of 415V, 3 phase connection, complete with base plate and accessories. Make : Kriloskar or Equivalent.The rate is inclusive of necessary vibration bed mounting, etc as per standard method as directed by departmental officers.

Supply, erection, testing and commissioning of 180 LPM 70 metres Head Pressurization pump with 10 HP electrical motor of kirloskar make with suitable base frame, Including necessary vibration bad mounting etc., including conveying, fixing and incidental charges etc complete as per standard specification and as directed by the departmental officers. Make: KIRLOSKAR / EQUIVALENT.

Supply , erection testing and commissioning of Fire Fighting 4 Way Fire Brigade inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT.

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia so as to release airlock in 100mm dia MS pipe at top most wet riser, ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR/ EQUIVALENT.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS 15683 with pressure gauge, discharge hose & control nozzie, wall mounting bracket, safety clip etc., ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT/ SAFETY FIRST / EQUIVALENT.

Supply and fixing Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS:15683., complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT.

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers

Providing, fixing pipe supports from coloumns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.

100 mm dia (Pump Room, Terrace, Wet riser)

80 mm dia (Wet Riser, All Floor Corridors)

50 mm dia (All Floor Corridors and Rooms)

Supply, Installation, testing and commissioning of Micro Processor based Conventional 12 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230/24 volt SMPS unit, 2 Nos. of 12 volt, 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.

Supply, Installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS junction box / false ceiling using fixing accessories llike screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers, (Make: Apollo / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers, (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers, (Make: Ravel / Equivalent)

Design,supply&fixing of Gas outlet points:(Self Sealing type-Single/Dinoutlet type) with S type bracket made up of copper and the out let of non-interchangeable for other gas.The outlet points are brazed with brass bracket with self sealing valve(stainless steel) with all accessories and complete set and are converted by plastic cover duly colour coated as per specific gas and button cover etc.,complete as directed by the departmental officers and as per IS Code 12827/1989 & ISO 7396/1987 specification.

Supply and installation of Medical gas copper pipe line arrangement for the following dia and thickness to hang on the wall of socket type connection installation of seamless cleaned and degreased non arsencial phosphorous gas copper pipe line with saddles complete with brazing work including all copper fitting (Tee,Elbow,Reducer,Coupling).The copper pipe lines should be tested suitable for a steam of working pressure of 17.34kg./cm2(17 bar) and confirm to BS 864 standard with specially made for brazed socket type connection.The medical gas copper pipeline should be tested as per standard and commissioning after painting as per international code no IS 2379/1963 Table-V.The pipe lines installed at the various wings and floors etc.,complete as directed by the departmental officers as per IS code 12827/1989&ISO 7396/1987 specification.

28mm dia Copper Pipe ODx0.90 thick

22mm dia Copper Pipe ODx0.90 thick

15mm dia Copper Pipe ODx0.90 thick

10mm dia Copper Pipe ODx0.90 thick

Brass Isolation valve. suitable for the copper pipe and should be of non lubricated 90 degree turn lever ball value of RB or Italy or reputed make,connected in line with medical gas pipe line system by using suitable size brass valve adopter union,ferrule,nipple,rubber "O" ring,taption lap and etc.All pipe line regulators shall be capable of controlling pipee line pressure and must compatible with the requirements specified in IS 12827-1989.All valves should be pneumatically tested for twice the working pressure for the gas line as per IS code 12827/1989&ISO 7396/1987 specification.

28mm dia Isolation valve

22mm dia Isolation valve

15mm dia Isolation valve

Oxygen Manifold arrangement of 2 banks x 12 cylinder each wing with semi automatic control panel which includes contact gauge 2 No., oulet pressure gauge, brass heavy dut IO x regulator 2 Nos., with suitable adopter, flexible SS Hose. Manifold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 12827-1989. Emergency alarms with illuminating display for low/ high pipeline pressure and malfunctioning of system. 1) Manifold top frame with provision for connecting 12 cylinders on right bank and 12 cylinder on left bank with high pressure interconnecting tubing, silver brazing, non return for claping 2 x 12 cylinders and related fastener. The O2 manifold should with stand a pressure of 140kg. / CM2 The installation is commissioned after testing as per standards and painted as per International Code and as directed by the Departmental Officers as per IS Code 12827 /1989 & ISO 7396/1987 Specification .

Nitrous Oxide Manifold Arrangements of 2 banks 3 Cylinder each wing, with automatic control panel which includes contact gauge 2 Nos. outlet pressure gauge, brass heavy duty IOX regulator 2 Nos. with suitable adopter, flexible SS hose. Manifold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 12827 -1989. Emergency alarams with illuminating display for low / high pipe line pressure and malfunctioning of system. 1) 6 x 6 cyliner Nitrus Oxide Manifold should be suitable with stand a pressure of 140kg/ Cm2 and above along with high pressure copper annealed tail pipes with end brass adapter suitable for Nitrous Oxide Cyliners and manifold. 2) Top frames comprising of high pressure copper pipe of size 12mm ID 1.5mm wall thick with high pressure brass fittings made of high tensile brass and connetions through non -return valves, high pressure copper tail pipes made of high pressure copper pipe size of 7mm ID 1.5mm thick. 3) The disign of middle and bottom frames should be provided to fit both round and flat bottom cylinders safely with fitted heavy duty regualtor. The Manifold should be tested at 3500 pig as per IS 12827/1989 & ISO 7396 / 1987 Specification.

Supply of Flow meter with humidifier bottle flow meter should be back pressure compressed flow meter should be accurate gas flow measurement with control range 0-13 litres per minute.It should meet strict permission and dumbling standard.The meter body should be made of unbreakable polycarbonate material and auto cleavable at 134 degrees centigrade.The rate includes flow meter and its accessories (Silicon tube with mask).The cost of materials including transport-taxes etc complete as standard as directed by the departmental officers and as per IS 12827/1989 and ISO 7396/1987 specification.

Supply of ward vacuum unit with gauge both mounted on a collection jar of capacity 600ml and with a wall bracket for mounting it on the wall. The collection jar should be made of unbreakable polycarbonate materials which is fully auto cleavable at 134 degrees centigrade as per standard specification and as directed by the departmental officers and as per IS 12827/1989 and ISO 7396/1987 specification.The rate includes cost of silicon hose with SS nipple on either side.

Supplying and fixing and testing of Theatre vaccum unit the unit should comprise of two reusable 2000ml shatter resistant bottle.Each made up of poly carbonate material and fully autoclavable at 134 degree centigrade,should have a vacuum regulator with instant ON/OFF switch and tree way Left/Right or both.All the above items should be mounded on a Trolley having free moving castor wheels.

Supply, installation, testing and commissioning of equivalent to Intersoil Rand Receprocating Air Cooled Type (10HP + 5HP) rating Vaccum Pump as per following provsiions. As per IS 12827 /1989 & ISO 7396/1987 Specification. a) Vaccum pump -10HP- 1set b) Electric motor - 5HP - 1 No. c) DOL Starter with OLR - 1 No. d) Vaccum switch - 1 No. e) Vaccum Gauge - 1 No. f) Control frame wth Fittings - 1 No. g) Suction Scrubber - 1 No i) GI & MS fittings- 1 No. j) Brass fittings - 1 No. k) Exhaust Silencer - 1 No. l) Base frame for motro and vaccum pump - 1 set m Pilot line with fittings - 1 set, Vaccum Room & Air Compressor Room Inside

Supply, installation , testing and commissioning of Compressed Air System of Reciprocating Oil Free Air Compressor belt driven type air compressor with following provisions. As per IS 12827 /1989 & ISO 7396/1987 Specification. a) 10HP Air Compressor - 2 Nos. b) Electric Motor 10 HP - 2 Nos. c) Dol Starter - L&T - 10HP - 1 No. d) Base Frame Kit (for Motor and Compressor)-1set. e) Pressure Switch - 1 No. f) Pressure Gauge - 1 No. g) NRV and Pilot Fittings - 1No. h) Delivery Tube - 1 No. i) Foundation Bolts & Anchor Fasteners - 1 Lot j) Belt Guard - 1 No. k) Air Driver 50 to 60 cfm. capacity - 1No. Drain Ball Valve - 1No. Air Outlet Compressor Room Inside Accessories. Non-Return Valves, Air Pressure Switch, Pressure Gauge, Isolation Valves, Air Filters etc., Inter connecting piping: Mild Steel Pipe of 2" with fittings.

Supply,installation,testing,and commissioning of MS fabricated vertical mounted type 1000 liters capacity vacuum receiver tank with inlet and drain holes provided suitable to operate with vacuum pump,etc., as directed by the departmental officers.

Supply, installation, testing and commissioning of MS fabricated Vertical Mounted Type 1000 liters capacity Compressed Air Receiver with inlet and outlet and drain holes provided suitable to operate with vaccum pump etc as directed by the Departmental Officers.

ELECTRICAL: Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with frame and making good of the concealed portion with suitable colour for Concealed PVC Light point/ fan point (for electronic regulator) (5 points/ Coil) Higher End

Wiring with 2 x1.5sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with frame and making good of the concealed portion with suitable colour for Concealed PVC Light point/ fan point (for electronic regulator) (6 points/ Coil) Higher End

Wiring with 3x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with frame and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End.

Supply and fixing of 1no.6A two module 5pin socket, 1no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections.Higher End

Supply and fixing of 7W/9W LED Lamp for BH point.

Supply and fixing of 4'20W LED Tube light fitting with Batten (Make : Higher End) with TW round blocks on wall or ceiling with LED tube with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete (Higher end) with 2module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18").

Supply and fixing of 300mm (12")sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan.

Supply & Fixing of AC / DC 76mm Buzzer/call bell suitable for 230 Volts 50 c/s single phase AC supply on suitable TW Board with push switch.

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour

Supply and fixing of WT bulk head fitting with guard suitable for 9W LED lamp.

Supply and fixing of 3Nos. 6A two module 5pin socket, 3nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End.

Supply and fixing of 1No. 6/16A two module socket, 1no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End

Supply and fixing of 3Nos. 6A 5 pin universal socket 2 module, 1 No 16A 5 pin universal socket 2 module with 3Nos 6A 1way SP 1module switch and 1No 16A 1way SP 1module switch concealed in suitable module metal flush type box (GI) covered with module white cover plate with frame (Plastic) (Higher End ) in flush with wall with earth connection. (In Various Ward) (SD-524)

Supply and fixing of 20Amps DP plug and socket in sheet steel enclosure with 32A DP MCB in flush with wall with earth connection.[For AC Plug]

Supply and fixing of 1000W automatic electric water heater of 25 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire,but without plumbing work

Supply and fixing of 8way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1no. 32A DP MCB switch as incoming and 6nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End.

Supply and fixing of 12way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1no. 40A DP MCB switch as incoming and 10nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and fixing of vertical type 4 way triple pole neutral MCCB DB in sheet steel enclosure double door metal cover with IP 43 protection with 1No. 125A FP MCCB with Spreader Terminal as incoming and 4Nos. 63A TP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB, MCCB and MCBs should be with ISI mark and Higher end.

Supply and fixing of vertical type 8 way triple pole neutral MCCB DB in sheet steel enclosure double door metal cover with IP 43 protection with 1No. 125A FP MCCB 1No. 125A FP MCCB with Spreader Terminal as incoming and 8 Nos. 63A TP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCCB DB, MCCB and MCBs should be with ISI mark and Higher end.

Supply and fixing of 7Segment 4way TPN MCB Sheet Steel Distribution Board with metal/acrylic door cover flush type / surface type fitted with busbars and neutral links with single or three phase MCB outgoings and seperate 4way provision for accomodating 1No 4Pole incoming MCB/Isolator and another seperate 4Way provision for accodating 1No. 4Pole ELCB/RCD (Totally 8ways in one segment)(3x4 ways in each segment )and seperate provison for MCB/Isolators (Totally 12 Nos) for sub incomers in 3 segments with label holder an provison for taking of cable for size not less than 35 sq.mm with the following in flush with wall earth connection only. 1) 63A 4P MCB - 1No 2) 63A 4P 30MA RCCB/ELCB-1No 3) 63A DP MCB Isolator - 3Nos 4) 6A to 32A SP MCB - 12Nos (SD-714) (For Lighthing Each Floor)

Supply and fixing of 7Segment 6way TPN MCB Sheet Steel Distribution Board with metal/acrylic door cover flush type / surface type fitted with busbars and neutral links with single or three phase MCB outgoings and seperate 4way provision for accomodating 1No 4Pole incoming MCB/Isolator and another seperate 4Way provision for accodating 1No. 4Pole ELCB/RCD (Totally 8ways in one segment)(3x4 ways in each segment )and seperate provison for MCB/Isolators (Totally 12 Nos) for sub incomers in 3 segments with label holder an provison for taking of cable for size not less than 35 sq.mm with the following in flush with wall earth connection only. 1) 63A 4P MCB - 1No 2) 63A 4P 30MA RCCB/ELCB-1No 3) 63A DP MCB Isolator - 3Nos 4) 6A to 32A SP MCB - 12Nos (SD-714) (For Lighthing Each Floor)

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling and making good of the concealed portion with suitable colour. (for call bell & 6 A plugs)

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. [For 3x6A Computer Plug, UPS Line]

Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour.[SD-57] [For 8W SPNMCB DB,20A MC Plug,Socket 16A Power Plug and Set Plugs]

Supply and run of 2 of 6 sqmm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour.[SD-59] [For 12W SPNMCB DB]

Supply and run of 4 of 6 sqmm (84/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.(4W 7S TPNMCB DB for lighting)

Supply and run of 4 of 16 sq. mm (101/0.45) PVC insulated S.C unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.(4W and 6W TPNMCB DB for Lighting and Power )

Supply and run of 4 of 25 sq. mm (168/0.45) PVC insulated S.C unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.(4W and 6W TPNMCB DB for Lighting and Power )

Supply and fixing of 32A TPNMC switch on suitable angle iron frame work with MS cable entry box with earth connection only.(For Pump Set )

Supply and fixing of 63A TPNMC switch on suitable angle iron frame work with MS cable entry box with earth connection only. (SD-166) (For 2Nos Lift Control Switch, and 1Nos Pump set)

Supply and fixing of 32A DP MCB in Metal box DP enclosure in flush with wall and making good of the concealed portion with earth connection. (Higher end) (for 5KVA UPS, Waiting Shed)

Supply and fixing of 32A FP MCB in Metal box FP enclosure in flush with wall and making good of the concealed portion with earth connection. (Higher End make) (Autoclave,)

Supply and Fixing of 16A Two-way switch in suitable Modular type GI box on wall with suitable front cover plate with earth connection (Higher End) (For Lift well lighting Control)

Supply and run of 3 of 2.5 sqmm (36/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable heavy gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 14SWG TC wire with painting of suitable colour. (For Lift Well Light Control)

Supply and fixing of 8 way single pole and neutral MCB DB with metal door cover with IP 42 protection with 1No. 32 Amps DP MCB as incoming and 2 Nos. 10A SP MCB and 2 Nos. 10A DP MCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (and of Higher End make) (For 1No Lift Room Lighting Control)

Supply and fixing of 63A FP MCB is suitable in Sheet steel enclosure in flush with wall with earth copnnection (Higher end).

Supply and fixing of 100A TPN sheet steel double break switch with HRC fuse and Neutral on suitable angle iron frame work with MS cable entry box with earth connection only.(In X Ray and CT Scan)

Supply and fixing of 200A TPN sheet steel double break switch with HRC fuses and neutral on suitable angle iron frame work with earth connection only

Supply, Erection, Testing & Commissioning of 630A capacity Dust & Vermin proof cubicle panel made out of 16SWG CRCA sheet steel enclosure with supply & fixing of the following interior mounting fuse switches with HRC fuses with a central bus bars chamber & two numbers of Horizontal cable chamber at top and bottom. 1 No 630A FP SDF Double Break switch withHRC fuse units(EB Incomer) and1 No. 400A FP SDF Double Break switch withHRC fuse units (DG Incomer) with Interlock system Outgoings: 200A TPN SDF Double Break switch with HRC Fuse units - 2Nos. 100A TPN SDF Double Break switch with HRC Fuse units - 2Nos. 125A TPN SDF Double Break switch with HRC Fuse units -7 Nos. 63A TP SDF Double Break switch with HRC Fuse units - 6 Nos. The bus bar chamber consist of 4nos. of 1"x 3/4" Copper flat for three phases and 1"x 1/2" neutral and also for interconnection for 630A switch. The interconnection with the bus bars to the 400A SDF DB Switches with 1" x1/2" Copper flat. The interconnection with the bus bars to the 200A SDF DB Switches with 1" x1/4" Copper flat and that 125A SDF DB Switches with30mmx 3mm copper flat & No.8 SWG Copper Conductor for 63A TPN Switch Interconnection.. And Double earth connection to all the switches should be done using No.8 SWG Copper conductor. The buses should be mounted on the SMC bus insulator at proper & sufficient spacing between the buses as per IE rules. The bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of 6mm thick as partition 2 runs of 1"x1/8" copper flat should be provided all around the panel for earth connection. Phase & Neutral copper buses should be provided with heat shrinkable sleeves using RYB & Black colours. Indicator lamps should be provided with toggle switches & Bakelite fuse unit.

Supply and laying of 2Run 3 ½ x400 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75m putting 0.15mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. (From MV Panel - 630A Sub Panel)

Supply and clamping of2 RUNS 3 ½ x 400 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 1/2 x 400 sq.mm PVC armoured LTUG cable, with earth connection.

Supply and providing cable end termination of 3.5 x 400 sq mm PVC LTUG Aluminum armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Supply and laying of 2Run 3 ½ x185 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75m putting 0.15mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. (For 250KVA Gen. Set)

Supply and clamping of 3 ½ x 185 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.(2 RUNS)

Supply and fixing of brass cable gland for 3 ½ x 185 sq.mm PVC armoured LTUG cable, with earth connection.

Supply and providing cable end termination of 3 ½ x 185 sq mm PVC LTUG Aluminum armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Supply and laying of 3½ x 25 sq. mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75metre putting 0.15mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. (For Lift)

Supply and clamping of 3 ½ x 25 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps. (SD - 222) (for Lift)

Supply and fixing of brass cable gland for 3½ x 25. sqmm PVC armoured LTUG cable with earth connection.(for Lift)

Supply and providing cable end termination of 3½ x 25 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete. (for Lift)

Supply and fixing of 5000VA UPS with 8Nos 12V 150AH tubular battery [Exide IT 500] with 1hour backup and 48months warranty for mentioned capacity on full load operation and the following features. [V- Guard/ APC/ equivalent] a) Inverter shall be free from workmanship defects, sharp edges, nicks, scratches, burs etc, all fasteners shall be fixed properly. The equipments shall be complete with all parts and all parts shall be functional. b) Enclosure shall conform to protection requirement of IRL to IS 13947 (part 1) 1993. c) Switching device shall be MOSFET (or) IGBT. d) Switching frequency shall be about 50HZ. II. Input ; 120V to 260V 50 HZ single phase AC III. Output : The variation in output voltage from NO- load to full load expressed as a percentage of no load voltage shall not exceed +1.5% over + 10 % and 20 % variation of the rated DC input voltage. The frequency of the output voltage shall be 50 HZ ± 1.3%. IV). Inverter efficiency minimum 85% as per CI.T.93 of ISS. v) Over load: inverter shall withstand 10% overload for at least 10 minutes. V).Protections. VI). a) When the Input voltage goes outside the range 120 volts and 260 volts the system shall switch over to inverter mode. b). Against over voltage, short circuit and over load at inverter output terminals. C). Battery reverses polarity. d). Protection against over discharge, The load shall be cut off as soon as the voltage of the battery terminal falls below.

i) 10.5V for 12V and ii) 21V for 24V battery system. e). The inverter shall incorporate an arrangement for automatic change-over of load from main supply to the inverter AC output in case of failure of mains supply with correct pending indication as per CL; 5.6 of IS 13314/ 1992 f). inverter should have surge protection also VII indicators. a) Following indicators shall be provided. i) Mains presence ii) Mains mode. iii) Battery charging. iv) INVERTER MODE v) Battery low. 4 battery bank; 12 Volts lead battery to IS 7372(1995 ) with amdts.No1,2&3 shall be reputed makes with ISI. 9) Battery stand with wheel angle iron frame arranged. (SR) [For OT, ICU, NICU and Dialysis ward] XIII - Part 'M' - 12 M - 2103

Design, Engineering, Supply, Fabrication, Erection, Testing, Commissioning and Handing over of 1No. 26 persons 1768kgs. Capacity Passenger cum Bed Lift (Gearless) With Machine Room as per the following specifications. 1. Location : 100 Beddded Critical Care Unit Building at Govt.Erode Medical College and Hospital at Perundurai 2. No. of Lift : One No 3. Type of Lift : Passenger cum Bed Lift with machine room - Gearless model 4. Capacity of Lift : 26 Persons / 1768kgs 5. Speed : 1.0 mtr / sec 6. Type of Drive : V3F Drive with enhanced ride comfort and near Zero Level Functions. 7. No. of Floors : Ground floor + 2 Floors 8. Total Travel : 10.8 Mtr / Pit 1800mm / Head room 4800mm 9. Leveling accuracy : High level accuracy with smooth and jerk free stopping. 10 Construction of Lift well : RCC with brick masonary/ Brick well. 11.Car : 1.5mm hairine finish High Quality S.S. Car and Hand rail, Granite flooring and Stainless steel False Ceiling. 12 Position of Machinery : Directly above the Lift well – Gearless with machine room. 13 No. of Landings : 3Nos in the front side. 14 No. of Car Entrance : One in the front side. 15 Car Entrance : Power operated V3F Drive, side opening Sliding Stainless Steel (1.5mm) Hairline finish door. 16 Landing Entrance door : side opening Sliding Stainless Steel (1.5mm) hairline finish door with provision for Emergency Exit key at All landings.

33 Provision for Intercom : To be provided in the Ground Floor & Machine Room with Phone (Press & Speak). 34 Lift License : Preparation of Drawings, payment of inspection charges to CEIG and insurance policy and Obtaining CEIG approval for the Lift as per Lift act should be done by the Lift contractor. 35 Floor Position : Included with LED display and floor annunciator. 36 Special Features: a. Infra red door sensor with full height screen b. Full width half height rear panel mirror c. S.S. hair finish hand rail in car d. Stainless steel signal features e. Vandal proof SS button with SS cover f. S.S. hairline finish door frames for landing doors g. V3F door operator h. Call register signal i. Stainless steel facio plates for car operating panel and landing fixtures j. Steel ladder for Lift machine room in lift pit. k. On / Off switch for fan and light l. Over-load warning indicator with audio Announcer m. Voltage stabilizer for control circuit. 35 Over Speed Governor, Phase failure and Phase reversal Relay, alarm bell, T guide brackets for car and counterweight, Rubber padding under the winding unit, Motor of adequate capacity, Electromagnetic brake with compression springs, Car safety gears, Buffers, Electro mechanical locks, Emergency key, side supporting angles, Motor over - load protection devices, Final limit switch main, suspension ropes, Counter weights, Lifting joist for mounting the Machineries.

36. Guarantee : Guarantee at least for one year for the materials and workmanship of equipments should be offered by the Lift contractor. 37. Site testing in accordance with IS 14665 should be carried out at the time of Handing over to the User department. 38. Supply, operation and maintenance manual and necessary tools for operation and a set of spare parts required for one year to be provided.(Johnson/Kone/OTIS)

Supply,testing, commissioning and handing over of 1No, 250KVA Diesel generator set of 0.8PF, 3phase, 415/ 420Volts, 50Hz, 1500 RPM complete in all respects as detailed below. A) ENGINE : Water cooled diesel engine suitable for generator application with a shaft out put of 199BHP suitable at 1500 RPM under NTP conditions . The engine shall comprise the following standard scope of supply: 1) Dry type Air cleaner 2) Expansion bellow 3) Radiator, radiator fan and mounting 4) Air to air charge cooler 5) Exhaust gas turbo charger 6) Lube oil cooler and lube oil filter 7) Fuel filter (pre and micro) 8) In-line mono-block fuel injection pump with governor and fuel feed pump 9) Electronic governor 10) 12V / 24V battery charging alternator 11) 12V / 24V Volt electric starter motor 12) Engine test certificate 13) Residential Mufler 14) Fly wheel with starter ring. Engine instrument panel/mounting: Engine control panel consisting of ON/ OFF/ START/ KEY, lube oil pressure gauge, oil temperature gauge, high water temperature gauge and electronic hour meter and RPM indicator. Safety system of Engine: The engine shall trip for the following conditions with Visual alarm device. 1) Low lubricating oil pressure 2) High water temperature 3) Vee - belt failure and over speed 4) Low battery indication. The Engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load.

26) 1set pilot lamps of 3Nos 27) MCCB of 250A capacity with magnetic thermal over load release, instant short circuit trip and under voltage release switch. 28) Rectangular copper bus bars (1No for each phase, neutral and earthing terminal) of adequate capacity duly colour coded with heat shrinkable PVC sleeves. 29) 1No mains voltage monitor 30) Hooter/Audio alarm for indication set fails to start and for DG O/L 31) 1set timers 32) Audio and visual indication arrangements for a) Low lubricating oil pressure b) High water temperature c) Over speed 33) 1No Earth fault relay 34) Isolator to Isolate the neutral Note: 1. The control panel should be complete with necessary fuses, cables, labels, other accessories with neutral isolation arrangements. 2. The engine should trip for the following conditions. a) Low lubricating oil pressure b) High water temperature c) Over speed 3. Supply and fitment of Auto mains failure panel to EB service with 250Amps switch and 250A contactors SCUF control relays timers etc.

D) ACOUSTIC ENCLOSURE : Acoustic enclosure shall be powder coated and fabricated of 16SWG CRCA MS sheet. The silent canopy shall be nut bolt type construction. Critical processes of punching are done on CNC machine to maintain dimensional accuracy of hole within 0.1mm powder coating done after seven-tank surface preparation process of sheet metal. Canopy panel and door shall have inside lining of FIRE-RETARDANT 64kg/m density mineral wool of 100mm thickness as acoustic material. Four hinged doors shall be provided to canopy. The maximum permissible sound pressure level should be as per the norms prescribed by the Central Pollution Control Board / State Pollution Control Board/ Competent Authority concerned or should be within 75 db(A) at 1 meter from the enclosure surface whichever is advantageous to the department. The emergency stop should be available on the enclosure panel. The enclosure provided shall be duly approved by the Engine Manufacturer of the Engine provided for Diesel Generator Sets mounted inside and should be to the satisfaction of inspection / testing authority concerned. SURFACE TREATMENT – PAINTING : The enclosure shall be suitably treated for degreasing, de-rusting and phosphating. The canopies are passed through seven-tank treatment thoroughly.

ADDITIONAL FEATURES OF CANOPIES : Canopy fabricated on CNC machines with dimensional accuracy of 0.1mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if any. WORLD CLASS COOLING PACKAGE: Canopies shall have cooling package for which it can perform at 45 deg c/ambient temperature. No grounding required on the ground, only a level surface capable of withstanding the DG weight. Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. The Gen set frame shall also be provided with hooks for unloading. Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well with in 5-7 deg centigrade. D) Base Frame Base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall have provision for mounting of acoustic enclosure on it. The supply of Gen set includes loading, unloading and transportation charges.

E) Fuel Tank Fuel tank of atleast 440 Ltrs capacity shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for cleaning or any maintenance. First charging of fuel oil to full capacity and first charging of battery while handing over to the department. Also supply of fuel oil to run the genset for a minimum of 8 hours on load or by using rheostat. F) Battery 2Nos 12V 180 AH battery Tools: Supply of tools like 15" cutting plier - 1no, screw driver 9" & 6" - 2no, DE spanners (6Nos) - 1set, Adjustable spanner - 1no, 1/2 lb Hammer - 1no, spanner for removing engine oil plug - 1no, Line tester - 1no for the maintenance and operation of Generator. (Make : Ashok Leyland/ Kirloskar/ Cummins/ Greaves/ Equivalent)

Supply and installation of exhaust piping of sufficient length with suitable MS pipe so as to extend outside the generator with necessary thermal insulation.

Erection of Gen set: Providing suitable concrete foundation with cement concrete 1:2:4 with a mainmum height of 3 feet from the floor level with sand cushion all around the foundation for erection of 250KVA Diesel Generator set over the existing fountation and erection of generator set with proper alignment over the existing fountation.

Supply and demonstration of the following safety accessories. a) 1 meter x 1 meter x1/2 inch 11kv rubber mat - 5Nos. b) one set of 4 nos. 9 liters fire buckets with metal stand frame - 1set c) first aid box with medicine - 1no d) 11 kV rubber hand gloves - 2 nos. e) 2 Kg capacity dry powder type fire extinguishers -1No f) Hand operated pump to transfer fuel from standard barrel to fuel tank-1No g) First aid chart in Tamil and English -1No h) Battery water acidity tester -1No i) Earth discharge rod -1No j) Danger board-1No k) PL lamp -1No

Preparation of site plan, physical layout, electrical line schematic diagram in 10 sets getting drawing approval from CEIG preparation of completion report, rectification report and arranging CEIG inspection and obtaining safety certificate preparation of 1 set of approved drawing and acopy of safety certificate in a neat frame work to be fixed in generator room and payment of CEIG inspection fees.

Supply erection testing commissioning of 2.00TR (6000 KCal/Hr) ABS Plastic split type Air Conditioner conforming to IS1391[Part 2] 1992 with Rotary compressor operating on refrigerant Non CFL suitable for wall mounting for operating on 230V 50HZ single phase AC supply with Three star rating Model as per BEE Specification and capable of performing the following functions. A) Cooling, B) dehumidifying C) Air circulating D) Filtering the installation work for the above split type AC units includes the following. 1. Mounting /fitting indoor and outdoor units at their respective locations. 2. Laying refrigerant pipe line of 6mtrs distance and connecting both units after drilling hole in the wall if required thickness of the copper tubing shall not be less than 0.80mm 3. Insulating the suction pipe with expanded polythene foam 5mm thick tubing. 4. Laying 15mm dia flexible PVC drain pipe of 6mtrs length to throw out the condensate water being formed in the indoor unit. 5. Leak testing the entire gas unit. 6. Charging refrigerant gas in the unit. 7. suitable electric wiring to be provided with 2.5sq.mm PVC insulated copper wire between indoor and outdoor units up to 4mtrs length and up to switch within 3mtrs of location of indoor unit.(Make -Carrier/voltas /Blue star make only)

Supply and fixing of 5KVA Automatic voltage stabilizer of wall mounting type with Automatic time delay switching arrangements suitable to operate on 230V Single phase supply.

Supply and laying of 5/8'' and 3/8'' copper pipe (Extra beyond 3Mtrs supplied with AC Unit)

Supply and fixing of MS Stand for fixing outdoor unit.

Supply, installation, testing and commissioning of 11TR factory assembled double skin AHU with 100mm-45kg/cum PUF Insulated detachable panels ,extruded thermal break aluminium profiles filled with PUF,panel external skin with 0.6 mm preplasticized sheet, panel internal skin with 0.6mm galvanized sheet, AMCA tested DIDW backward/ forward curved centrifugal fan with EFF1 rating motor, drive arrangement with taper lock pulleys for fan and motor, vibration isolators out of heavy duty rubberized mounts, prefilters with 3ply HDPE 50mm thick filters having an efficiency of 90% 10 Micron and 5 Micron, 6row /12FPI deep DX copper cooling coil with copper header and aluminium fins, GI mist arrestor, condensate coil trough with SS-304-20G insulated with 9mm closed cell elastomeric foam, guard for inspection door, out let damper of aerofoil blades & PVC gears, and flexible fire retardant canvass complete with galvanized hardware. Each of the cooling coils will have independent distributers, electronic expansion valve kit, catch all drier, independent DX coil circuit to connectivity to each ODU circuit. Appropriare devices to be installed to monitor the Temperature, Humidity and Diff. Pressure inside the Operation Theatre. (Carrier/ Voltas/ Bluestar make/ Equ.) (MR)

Design, supply, installation, testing and commissioning of DX 11TR nominal capacity factory assembled Air-cooled Condensing unit fixed with energy efficient scroll compressor along with grooved copper tube or aluminium fins air cooled condensor coil with anticorrosion coatings, liquid, accumulator, low noise alumimium propeller condenser fan with Fan motor etc all suitably assembled neatly in heavy duty GSS sheet metal cabinet and duly powder coated as per specification. the unit to include built in safety controls like HP/LP switch power quality protector, in built thermal/ temperature protection. (carrier make)

Supply and fixing of Laminar Air flow Plenum for SS304 - 1.0 mm Thich casing, Mini Pleat Hepa Filters for 100mm Thick- Flange type, OT Pendant Light provision for 600X600, With SS304-1.2mm Thick perforated sheet. PLENUM SIZE: 1800L X 2400W X 350HHigh Efficiency particulate Air (HEPA) filter specification: Filter Size : 8 feet x 6 feet x 1 feet Classification : H-13 Construction :Panel Type Efficiency :99.97% Optical efficiency at .3 micron Cleanliness level: Class 100 As per NABH Standard Spacers: Aluminium Initial pressure drop:25 mm W.C Final pressure drop : 75 mm W.C Duct holding capacity:4750gm/Sq.mtr Framing :Aluminium (Box type) Washable : No Test reports to be furnished from approved Government External Quality Assurance Lab/ Agency to meet the testing parameters after commissioning of the AC system with HEPA filter as per NABH standards.

Supply and filling of non-CFC Refrigerant Gas.

Supply & fixing of hard drawn copper Refrigerant piping of suction line of Size 7/8” inches with necessary fitting and clamp etc…

Supply & fixing of hard drawn copper Refrigerant piping of liquid line of size 5/8” inches with necessary fitting and clamp etc…

Supply and fixing of flexible canvas connection between indoor unit and ducting and rubber pads, with ceiling Support angle rods etc...

Supply and fixing of 50mm thick anti vibrating rubber pads

Supply, Fabrication and Installation of 22 G Sheet GI Ducting for both suction and Return arrangement insulate with for Operation Theatres with inter linking arrangements with necessary angle supports, anchor fasteners and threaded rods etc... as required.

Supply and Providing Thermal Insulation of 9mm thick Class ‘O’ Fire Retardant –XLPE with aluminium foil.

Supply & fixing of Acoustic insulation for Supply air duct using 12 mm thick class 1 rating Open cell nitrile rubber /XLPE insulation.

Supply and fixing of powder coated Extruded aluminium supply air grilles/diffuser with MS volume control damper for supply.

Supply, fabrication and fixing of Volume control dampers individually across the duct.

Supply and fixing of 1 inch PVC water drain pipe line on wall with suitable Clamp as required.

Supply, fabrication and fixing of suitable MS angle support frame for mounting the out door Units.

Supply, fabrication and fixing of suitable MS angle support frame for mounting the in door Units.

Supply and providing civil concrete block for mounting the air coditioning unit

Supply and providing of pipeline nitrile rubber insulation for suction line Refrigerant pipe as required.

Supply and fixing of microvee filter 600x600mm size fine microwave mesh filter with efficiency of 5 micron level for return air.

Supply, fabrication and fixing of Fresh air Louver made of extruded aluminium with bird screen provided with intake louvers.

Sand cement plastering (1:3) of 20mm thickness with chicken mesh for external exposed portion of duct

Supply and run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/ supports on wall/ floor/ ground for earth connection

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps/ supports on wall/ floor/ ground for earth connection.

Supply and Laying of 4 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 4 x 10 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps. (for St.Light)

Supply and fixing of brass cable gland for 4 x 10 sq mm PVC armoured LTUG cable, with earth connection. (for St.Light)

Supply and laying of 3½ x 50 sq. mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75metre putting 0.15mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and clamping of 3 ½ x 50 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3½ x 50. sqmm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3½ x 50 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Earthing as per the ISI specification with an earth electrode of 2.1 mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

vivek vijay and company

LOTUS CONSTRUCTION