Construction of Auditorium cum Conventional Hall at JNCollege Pasighat, in East Siang District AP

Amount

SH:- Earth work

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Earth work in rough excavation, banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with 1/2 tonne roller or wooden or steel rammers and rolling every 3rd and top most layer with power roller of minimum 8 tonne and dressing up in embankment for road, flood banks, marginal banks and guide banks or filling up ground depressions lead upto 50 m and lift upto 1.50 m. (b) Hard Soil

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

SH:- Concrete

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in: (a) Foundations and plinth

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : (a) M20 (1 cement : 1.50 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars,post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. b) M20 (1 cement : 1.50 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. (a) M20 (1 cement : 1.50 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with M20 (1cement : 1.50 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in retaining wall (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets etc from top of foundation up to floor two level excluding cost of centring,shuttering and reinforcement in : (b) M15 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.50 : 3 (1 cement : 1.50 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 1.50 : 3( 1 cement: 1.50 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Column, pillars, posts and struts etc.

c) Lintels, beams, girders, bressumers and cantilevers etc.

d) Stairs (excluding landings) except spiral stair cases.

e) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

f) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Reinforcement of RCC work including bending, binding and placing in position complete. (b) Tor/ TMT steel

SH:- Walling

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) : For fixed portion. (1.3) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beading shall be paid in basic item) (4.3) With float glass panes of 8 mm thickness.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Door /Window / Ventilator Frames:- Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticalssides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineer- in-charge.

Window/Ventilator Shutters:Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),uPVC extruded glazing beads of appropriate dimension,EPDM gasket,stainless steel(SS 304 grade)friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100x8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.(Single/double glass panes and silicon sealant shall be paid separately)Note:For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. a)Casement window double panels with top fixed with S.S.friction hinges (350 x19x1.9mm) made of (small series) frame 47x50mm, sash 47x68mm & mullion 47x68 mm all having wall thickness of 1.9± 0.2 mm and single glazing bead of appropriate dimension.(Area of window upto 2.50 sqm).

Flush Door Shutters:- Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

WC/Bathroom and other Door Shutter:- 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For WC and bathroom door shutter).

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. (b) Ornamental grill.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete. (b) 250 x 10 mm

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete. (a) 125 mm

Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete. a) 300 x 16 mm

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone shingle 40 mm nominal size).

SH:- Roofing & Ceiling

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Providing Alumunium Troughed Sheet Roofing fixed with 'J' hooks,bolts,nuts, washer with bitumen (the 'J' hook,nut and bolt are as per IS:733 of 1983) and limpet washer filled with white lead complete excluding the cost of the purlins,rafters and trusses. a)Using 0.65 mm thick Alumunium Troughed Sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. (b) 0.63 mm thick GI sheet

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : (a) 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (b) 110 mm diameter

SH:- Flooring & Finishing

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete (c) Size of Tile 800x800 mm

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : (a) Makrana white second quality

Extra for pre finished nosing to treads of steps of marble stone.

Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre.

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

15 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Providing two coats of acrylic water based wall putty/ wall filler of Asian Paints/ Berger/Dulux over concrete/ cement plaster/ brick walls and ceilings both internal and external after removing all the loosely adhering material from the wall/ ceiling surface with the halp of emery stone, putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

SH:- Sanitary & Water Supply and Drainage

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x430x265 mm sizes respectively with CI automatic flushing cistern with fittings, RS or CI brackets standard size galvanized steel flush pipe and spreaders with brass unions and GI clamps complete including painting of cistern and fittings, cutting and making good the walls and floors where required. (a) One urinal basin with 5 Litres CI automatic flushing cistern

Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain in enamel led flush band, 20 mm over flow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required. (a) WC pan with white plastic seat and lid.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required. (b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). (a) 750 x 20 mm size

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes. a) 100 mm dia

c) 50 mm dia

Providing and fixing sand cast iron heel rest sanitary bend. a) 100 mm dia

c) 50 mm dia

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. (a) 100 x 100 x 100 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. a) Concealed work, including cutting chases and making good the walls etc. a) 20 mm nominal outer dia Pipes

b) 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. a) External work. a)50 mm nominal outer dia Pipes

b)62.5 mm nominal outer dia Pipes

Providing and fixing brass full way valve with wheel of approved quality. a) 40 mm nominal bore

b) 50 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (a) 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (a) 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. (a) 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. (a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Septic Tank

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in: (a) Foundations and plinth

Reinforced cement concrete in walls (any thickness) including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in :

Centring and shuttering including strutting, propping etc and removal of form work for : (b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Reinforcement of RCC work including bending, binding and placing in position complete. (a) Cold twisted bars.

SH : Electrical Installation

Proving 1.50 sqmm PVC insulated PVC single core copper conductor cable (91 meter per coil)

2.5 sqmm PVC insulated single core copper conductor cable

4 sqmm PVC insulated single core copper conductor cable

Providing black tape

5 Amp P/Type switch

Sunmica board 8" x 10"

5 Amp Socket with 5 Amp switch combined

PVC casing caping flat channel of size 1"

PVC (Elbow Tee & bent) 3/4" size

Screw 1-1/2"

CFL Bulb 20W

MCB D.B

T. P. & N main sqitch 100 AMP.

32 AMP single pole circuit breaker.

Fan clamp.

Celing Rose.

Hack saw blade ( 12 per packet ).

UG cable 95 Sqmm 3 1/2 core PVC insulated PVC sheated armoured alluminum cable conforming to IS : 1554/1976 (Part-II) as ammended upto date

UG cable 35 Sqmm 3 1/2 core PVC insulated PVC sheated armoured alluminum cable conforming to IS : 1554/1976 (Part-II) as ammended upto date

UG cable 25 Sqmm 3 1/2 core PVC insulated PVC sheated armoured alluminum cable conforming to IS : 1554/1976 (Part-II) as ammended upto date

Sunmica board 7" x 4"

5 Amp Socket

Wooden Screw 1"

Sunmica board 4" x 4"

200 Amps 4 Pole changeover switch

Providing GI Earthing Plate Size- 600 x 600 x 6mm as required

Providing 200 Amp Cut out

Providing 250 watts Sodium Vapour Lamp fitting with Lamp

Providing 8 SWG GI wire

4' - 0", 40 w flouroscent light fitting with 40 w tube light.

A. C. Ceiling fan 1400 mm sweep complete with regulator etc as required.

Wiring for light Fan point/3 pin 5 amp/15 amp socket out let with 5 sqmm/2.5 sqmm/4 sqmm and 6 sqmm PVC copper/Al. wire i/c earthing and connection etc as required. The work is to be carried out by a qualified wire man ( job work only ).

SH:- STAGE WORK

Light Bar: Providing and Fixing of Motorized light bar

LED PARrgbw 54 LEDs 3W 4 digital display. There dimmer manual mode, running, strobe, speed adjustable, adjust the data with a power saving, boot automatically recover data. DMX 512 protocol - 6 DMX channels Main dimmer , RGB color changing , Strobe effect, Auto play with internal programs , Master/Slave function, Stand alone mode . Power supply: AC 100V-AC240V 50/60 Hz. Make :Deftech

LED PAR Supply of 54LEDs 3W 15° (Warm white) portable, lightweight luminaries, high intensive light with low heat output, Very robust luminaries, suitable for indoor Public and commercial buildings, Music festivals, stadiums, theme parks, Stages, Exhibition halls. digital display, no fan required, light output: 4,200 lm , Up to 16.7 million colors, Dimming range: 0...100 % built-in control of statics, auto, sound,DMX512 monitoring, Strobe effect, Lifetime: up to 30,000 h with beam angle: 15°, 30°, 45°, 60°, IP20. Auto play with internal programs, aster/Slave function, Standalone mode. Power supply: AC 100V-AC 240V Make : Deftech

200W LED Profile Spot 19 Degree Light 200W LED Profile Spot 19 Degree Light complete with 3200K CCT Colour Tempreture, CRI & TLCI above 90, DMX512 dimming with 1or3 channel modes, Black finish housing IP20 protection having Lux@2 Mtrs above 27,000 suitable to illuminate the key presenter or talent on stage.Make : Deftech

LED Moving Head Spot- 230W . LED Moving Head Spot-230W, Pan Range-540* & Tilt Range-180*, 8 Bit/16 Bit High Precision Movement, 1 Static Gobo Wheel-7 Fixed Metal Gobos, Motorized Zoom from 12* ~ 18* and complete as per direction of Engineer-In-Charge complete etc as reqd.Make : Deftech

Blinder :4-Eyes white & warm white High-Power Warm white LED COB Lamps: 4 x 100W (400w) Optics: 80 degree Wide Flood Individual control of 2-Eyes DMX operation – with 10 DMX channels Wireless DMX ready – using special 3-Pin XLR socket with 5vdc Vertically & Horizontally expansion possible to build 4/8-way or more… Possible to create larger MATRIX for Pixel mapping effects. Powercon IN & OUT for mains (supplied with 1xMains & 1xLink cables) Power: 90 – 260VAC – 50/60 Hz, 220 watts Make Deftech

Light Point Light Point Wiring from Patch panel/ Distribution Board to be provided near stage to various stage light fixtures with 2.5sq.mm 3core PVC Insulated and PVC sheathed Cable (ISI Mark) including cable tray of suitable size for laying these wires on the tray including 20amps metallic clad sockets / 15amp socket to direct points with box at top.

DMX Splitter Supply and fixing of 1 in 6 Out DMX Splitter. Make : Deftech

Mini Pearl Lighting Controller2.Voltage:AC 110V-240V/50~60Hz. N.W(1piece):14 Kg Size(1piece):550×460×350 mm. Mini pearl 1024 can control 96fixtures at the same time. The controller can read the pearl's fixture library format(r20) Inside dozens of effect shapes,also can running 10 scenes Make : Deftech

DMX interconnection cable

Clamp

Main Curtain : made out of Velvet cloth with horizontal sliding arrangement complete with Gear box, Rolling Drum, fixing rails, brackets, sliding arrangement & motorized operation complete with nylon runners,master runners, pullies, 3 mm steel wire rope, 1 Flange type motor , 2 Nos. Air Breaker Contractor (deftech), 2 Nos.15 amps. Micro switches (deftech) for auto stop 3 nos push buttons for Forward, reverse and stop positions. The curtain should be draped to half area when in closed Position. Minimum overlap at Centre should be900mm and should be stitched in double gathering. Approx. Curtain Size 9mt x 4mt etc. complete with installation as per the site requirement.

Rear Curtain : made out of Black Glaze cotton cloth with horizontal sliding arrangement complete with Gear box, Rolling Drum, fixing rails, brackets, sliding arrangement & motorized operation complete with nylon runners,master runners, pullies, 3 mm steel wire rope, 1 Flange type motor , 2 Nos. Air Breaker Contractor (deftech), 2 Nos.15 amps. Micro switches (deftech) for auto stop 3 nos push buttons for Forward, reverse and stop positions. The curtain should be draped to half area when in closed Position. Minimum overlap at Centre should be900mm and should be stitched in double gathering. Approx. Curtain Size 8 m x 4 m etc. complete with installation as per the site requirement.

Main Frill bar, fixed type, made out of 25mm dia GI pipe, supported from ceiling Structure, as required. Frill to be made out of Velvet

Subsiquent Frill bar, fixed type, made out of 25mm dia GI pipe, supported from ceiling Structure, as required. Frill to be made out of Blackglaze cotton

Wings: Providing and fixing cloth wings made out of black glazed cotton fixed on 6 mm thick commercial plywood fixed on one side of MS 50 mm x 25 mm x Pipe welded frame work. The pipe frame work made out 25 mm x 50 mm pipe C/o 1200 x 600 fixed with overhead pivot track complete with duly panted on both frame work. Size 1.2m X 6m etc. complete with installation as Per Site Requirement.

SH:- PLUMBING

Supplying, fixing, installation & commossioning of storage type electric water heater with necessary fiitings and accessories complete in all respect. Make: Racold, A.O. Smith 15 Ltrs.

Providing & fixing brass/ gun metal lever operated ball valve. Tested to a pressure of 15 Kg / Sqcm. Including flanges/union, nuts, bolts, washer etc. Complete as required. Make : Zoloto/SKS/NVR/Audco 32 mm dia

40 mm dia

50 mm dia

Providing & fixing in position 25 mm dia lawn hydrants consisting of 25 mm dia Ball valve, GI nipple and threaded hose receiver.Hydrant taped off from main CPVC pipe with G.I. Heavy class upto 0.6 mtrs. in length with P.C.C. base to provide strength to the hydrant, complete as required as per approved drawing.

Supplying,commissioning of SS vertical multistage centrifugal pump. Each pump shall have TEFC 2900 RPM three phase electric motor. The pump shall have cast iron head, base plate SS Shaft/ Impeller/ Intermediate chamber. Pump shall be provided with mechanical seal. The Panel shall include all required fuses, motor protection, main switch, float controls, all automation operations etc. complete in all respect. Water Transfer pumps (For OHT Filling) Flow rate : 5 M³/HR Head : 25 Mtr. Qty : 2 Nos. (1W+ 1S) Note: Vendor to submit proposed pump model with duty curve.

SH:- ELECTRICAL WORKS

Supply of below mentioned Items - Data Socket(RJ-45 CAT6) (Legrand Myrius)

Supply of following 1100 volt grade XLPE insulated PVC inner sheathed and FR PVC outer sheathed Aluminium conductor armoured LT cables .(Make: Cable- Gupta Power, Polycab, RR Kabel, Havells ) 3.1/2 core 35 sq. mm

3.1/2 core 50 sq.mm

3.1/2 core 95 sq.mm

3.1/2 core 70 sq.mm

3.1/2 core 120 sq.mm

3.1/2 core 150 sq.mm

Supply of following 1100 volt grade XLPE insulated PVC inner sheathed and FR PVC outer sheathed Cu conductor armoured LT cables .(Make: Cable- Gupta Power, Polycab, RR Kabel, Havells ) 4 core 6 sq. mm

4 core 10 sq. mm

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply, Installation, Testing and Commissioning of Surface mounted 2' x 2' (Nominal size) LED panel having lumens output not less than 3200, efficacy > = 100 lumens / watt and not higher than 32 Watt, THD should be less than 10%, luminaire power factor should not be less than 0.90 with minimum 50000 burning hours, CRI≥80 and CCT 5700-6500 K(as reqd.), with inbuilt electronic driver with efficiency should not be less than 85% with surge protection 2.0 KV, IP-20 rated made out of CRCA powder coated enclosure with suitable diffuser, i/c connection with suitable size of MS Chain and making connection with 1.5 sqmm. FRLS Copper conductor single core cable i/c earhting etc. as required.

P & F of IP20 LED batten type light fixture made from CRCA sheet stlle housing suitable for mounting LED tube system (integral driver), Power consumption of 18W/36W, 1500/3000 lumens, system lumen efficiency 80 lm/ watt output, life time of 50000 burning hours with 70% initial lumen maintained. CCT 3000° K, 4000° K and 6000° K. 4’ LED Tube shape fixture 18W

P & F of IP20 LED Recessed/ Surface Mounted Round/ sqaure Non Dimmable Downlight with die-cast aluminum housing & Heat sink for heat dissipation, high purity reflector with external driver having efficiency >85% and in compliance to IEC standards. ( supplied together with luminaire) Power consumption of =< 7w/10w/8w/12w/15w/18W with 100/500/750/1100/1250 lumens, system lumen, efficeancy of 70 lm / Watt or 100 lm / Watt output suitable to replace 1x18W/ 2x18w/2x26w CFL downlights, life time of 50000 Burning Hours with 70% of intial Lumen maintained. CCT 3000° K, 4000° K and 6000° K. Fixture shall be CE Compliance. Surface Mounting LED downlight 18/20 W

Make: Light- Philips , Fan -Havells Supply , Installation, Testing, Commissioning of 12 ft., 8 /5 anodized/ powder coated blades 400 W HVLS Fan working on 3 phase, 415 V, 50 Hz supply of brushless DC technology, IP 64 Protection , class F insulation, >98% efficiency with reinforced bearing etc., speed controlled by VFD of suitable rating, operated through Key pad at approachable location having keys for starts / stop, reverse/ forward & speed increase/ decrease option, control panel with VFD alongwith top or bottom cable entries with detachable cable glands sheet etc. confirming to IP 42, power and control cable of suitable rating in PVC pipe as required ,blades (aluminium HE 9 grade having suitable ribs for extra strength, with internal wire rope wrapping to prevent fall out in case of blade breakage ) alongwith with hub (single piece die casted LM 6 aluminimum grade material, radiography tested), tension wire, top safety ring , mounting rod, extension tube of stainless steel , metal guy wires, safety ropes, nut bolts etc. as required confirming to IS 2062 etc. as required as per site requirement.

Indoor Dome Camera 2MP IP Fixed Dome Camera: 1920 × 1080 resolution, Standard video compression with high compression ratio (H.265), ROI (region of interest) encoding, Lens-4mm@ F2.0, Angleof view: 85°(6mm, 12mm optional), Progressive scan CMOS, capture motion video without incised margin, Support dual stream, and the sub-stream for mobile surveillance, High-performance and long service life Infrared LED, up to 30 meters IR range, IR cut filter with auto switch PoE (Power over Ethernet), 3D DNR, Ingress Protection level: IP66, Electronic shutter for different surveillance environments Impact Protection: IEC60068-2-75 test, Eh, 20J; EN50102, up to IK10, Other functions: alarm, mirror, etc Support intrusion detection and line crossing detection, Support VCA, which is compatible with NVR for the second time of video searching and analysing,Operating Conditions: -30 °C to 60 °C (-22 °F –to 140 °F), Humidity 95% or less (noncondensing).

2MP IP Fixed Dome Cam 2MP IP Outdoor Bullet Camera: 1920 × 1080 resolution, Standard video compression with high compression ratio (H.265), ROI (region of interest) encoding, Lens-4mm@ F2.0, Angleof view: 85°(6mm, 12mm optional), Progressive scan CMOS, capture motion video without incised margin, Support dual stream, and the sub-stream for mobile surveillance, High-performance and long service life Infrared LED, up to 30 meters IR range, IR cut filter with auto switch PoE (Power over Ethernet), 3D DNR, Ingress Protection level: IP66, Electronic shutter for different surveillance environments Impact Protection: IEC60068-2-75 test, Eh, 20J; EN50102, up to IK10, Other functions: alarm, mirror, etc Support intrusion detection and line crossing detection, Support VCA, which is compatible with NVR for the second time of video searching and analysing,Operating Conditions: -30 °C to 60 °C (-22 °F –to 140 °F), Humidity 95% or less (noncondensing).

NVR 32 Channel Third-party network cameras supported, Up to 5 Megapixels resolution recording, HDMI and VGA output at up to 1920×1080P resolution, 32-ch network cameras can be connected with 100M/200M incoming bandwidth4 SATA interfaces 4 TB Each Plug & Play with 16 independent PoE network interfaces Support network detection, including network delay, packet loss, etc

HDD 4 TB SURVEILLANCE HARD DRIVE or According to 1 Month Backup

Patch Panel Cat-6 patch panel 24 port

Cat-6 patch panel 8 port

Switch 24 Port 10/100/1000 POE Switch

8 Port 10/100/1000 POE Switch

Patch Cord Cat-6 patch cords, 1 Mtr

Monitor 32" LCD 24X7 Surveillance Monitor

STREET LIGHTING Supply, Installation, Testing & Commissioning of Street lighting Two arm GI pole (6 mtr. above ground) along with necessary pipe-reducer / fixing-bracket for fixing the Luminaire, weather proof, FRP junction box with fixing brackets. Bracket shall be of GI pole Each pole to be provided with following as minimum. > Two no. 70W LED fixture Outdoor type (IP67). > Weather proof FRP Junction box with degree of protection IP55 with canopy. Each box shall be supplied along with 2 pole MCB . Boxes shall be provided with a hinged lockable door with neoprene gasket lining all over. Lock shall be operable with an allen key. The terminals in the junction box of the lighting poles shall be suitable for loop-in / loop-out of atleast 4Cx16 sq.mm aluminium armoured XLPE cables. Box shall be provided with 20 mm wire entry hole on the rear side. This entry hole shall have rubber / PVC bush. Two earthing terminals suitable for GI earthing wire shall be provided for each box. > Each pole to be provided with base plate, foundation bolt if required etc. all necessary hardwares required for installation & successful commissioning of pole. > Necessary FRLS Cu. wire of 1 Sq.mm from MCB to fixture. > Design, Supply and Execution of Civil work is in CONTRACTOR scope. > Warranty :- Complete White LED street Light must be warranted against any manufacturing / design / erection defects for a minimum period of 2 year from the date of supply.

STREET LIGHTING Supply, Installation, Testing & Commissioning of Street lighting Single arm GI pole (7 mtr. above ground) along with necessary pipe-reducer / fixing-bracket for fixing the Luminaire, weather proof, FRP junction box with fixing brackets. Bracket shall be of GI pole, Each pole to be provided with following as minimum. > One no. 70W LED fixture Outdoor type (IP67). > Weather proof FRP Junction box with degree of protection IP55 with canopy. Each box shall be supplied along with 2 pole MCB . Boxes shall be provided with a hinged lockable door with neoprene gasket lining all over. Lock shall be operable with an allen key. The terminals in the junction box of the lighting poles shall be suitable for loop-in / loop-out of atleast 4Cx16 sq.mm aluminium armoured XLPE cables. Box shall be provided with 20 mm wire entry hole on the rear side. This entry hole shall have rubber / PVC bush. Two earthing terminals suitable for GI earthing wire shall be provided for each box. > Each pole to be provided with base plate, foundation bolt if required etc. all necessary hardwares required for installation & successful commissioning of pole. > Necessary FRLS Cu. wire of 1 Sq.mm from MCB to fixture. > Design, Supply and Execution of Civil work is in CONTRACTOR scope. > Warranty :- Complete White LED street Light must be warranted against any manufacturing / design / erection defects for a minimum period of 2 year from the date of supply.

SUPPLY AND INSTALLATION OF Street lighting panel with timer ckt. & photo sensor ckt. suitable for IPW55 , RYB LED phase indications, RAL 7032 paint shade, wall mounted suitable for flush mounting, bottom cable entry, suitable for pad locking arrangement with following: 1. Incomer(1 no.) - 63A, 415V AC,4P MCB, 10kA SC rating 2. Outgoing( 3 nos.) - 20A, 230V, 4P MCB, 10kA SC rating

SH:- INTERIOR WORKS

Wall Paneling Specification Upto -Providing and fixing A&T Make Grooved Slats Acoustical Wood based Fire Resistance panels with lineal perforations.The panels shall be melamine laminate panels 2430mm x 128mm x16 mm wirh as per nrc require, Toungue and Groove edges for seamless mounting having density as per nrc.. The back of the panels are perforated with 10mm diameter circular holes with a nonwoven fabric covering of 0.2mm for providing Sound absorption via the acoustic impedance method .Panel is to be fixed on Strut Keen18 framework with screw fixed horizontal / vertical to cross channel 25 mm at every 600mm c/c with centre & edge bracket in tongue & groove system on Strut Keen 18 framework. The cavity of framework should be inserted with As per rt require 50 mm with surface density of 1000 gsm and alongwith all accessaries and direction of Engineer in charge.The paneling work shall be done complete in all respects as per detailed working drawings. The panelling should be properly done in proper alingment and level as per satisfaction of the Architect/E.I.C all complete for all heights and levels. (Make : A&T)

Wall Paneling Above DADO Specification :- Providing and Fixing A&T made Polyster fiber acoustical penal with nrc .82 9mm Behind sheets of magnacium or cement Panel of size 1200x600x25 mm, With framing of alumimum section of 600*600 , having design of colurs and lights shades as per choice of drdo or authorise agency, need to cover .90 nrc of backing require glass wool and framing and screwing with standard requirement and as per Design by authorize agency (Make:A&T)

Stage Flooring : Providing & fixing 75x14 thick in random length, 2nd class teak wood planks flooring with T&G joints on a layer of 19 mm thick ply of approved make and manufacture fixed to hard wood, 50x50 mm at 600 mm c/c in on other direction, the framework to be filled with 50 mm thick rockwool density 48 kg/m3.PU polishing of teakwood on exposed surface in horizontal/vertical plane (rate for flooring shall include providing additional framework required for housing microphone and power outlet junction boxes including providing & fixing hinged 18 mm thick teakwood cover for junction boxes.(Make: Any standard, )

Wall Paneling Specification Upto -Providing and fixing A&T Make Grooved Slats Acoustical Wood based Fire Resistance panels with lineal perforations.The panels shall be melamine laminate panels 2430mm x 128mm x16 mm wirh as per nrc require, Toungue and Groove edges for seamless mounting having density as per nrc.. The back of the panels are perforated with 10mm diameter circular holes with a nonwoven fabric covering of 0.2mm for providing Sound absorption via the acoustic impedance method .Panel is to be fixed on Strut Keen18 framework with screw fixed horizontal / vertical to cross channel 25 mm at every 600mm c/c with centre & edge bracket in tongue & groove system on Strut Keen 18 framework. The cavity of framework should be inserted with As per rt require 50 mm with surface density of 1000 gsm and alongwith all accessaries and direction of Engineer in charge.The paneling work shall be done complete in all respects as per detailed working drawings. The panelling should be properly done in proper alingment and level as per satisfaction of the Architect/E.I.C all complete for all heights and levels. (Make : A&T)

Wall Paneling Above DADO Specification :- Providing and Fixing A&T made Polyster fiber acoustical penal with nrc .82 9mm Behind sheets of magnacium or cement Panel of size 1200x600x25 mm, With framing of alumimum section of 600*600 , having design of colurs and lights shades as per choice of drdo or authorise agency, need to cover .90 nrc of backing require glass wool and framing and screwing with standard requirement and as per Design by authorize agency (Make:A&T)

Stage Flooring : Providing & fixing 75x14 thick in random length, 2nd class teak wood planks flooring with T&G joints on a layer of 19 mm thick ply of approved make and manufacture fixed to hard wood, 50x50 mm at 600 mm c/c in on other direction, the framework to be filled with 50 mm thick rockwool density 48 kg/m3.PU polishing of teakwood on exposed surface in horizontal/vertical plane (rate for flooring shall include providing additional framework required for housing microphone and power outlet junction boxes including providing & fixing hinged 18 mm thick teakwood cover for junction boxes.(Make: Any standard, )

CARPET FLOORING: Auditorium Area Carpet -- Carpet/carpet tile on floors as per make, shade, texture, type for specified area over necessary base & as per approval. All complete as per approval & instruction of Architect

SH:- HVAC WORKS

To design & supply air cooled DX type airconditioning system (one to one) complete with outdoor units comprising condenser, scroll/rotary comresssors, etc. and indoor units comprising various types of evaporative blowers, expansion device , microprocessor based remote controls, etc. 17.0 TR DUCTABLE UNIT (We have consider 16.7TR with R22)

11.0 TR DUCTABLE UNIT

2.5 TR DUCTABLE UNIT

2.0 TR WALL MOUNTED UNIT

1.5 TR WALL MOUNTED UNIT

DX SYSTEM INSTALLATION: Lifting/ shifting, installation, testing, and commissioning of outdoor/indoor units including M.S. stand,refrigarant charging/top up, fixing of remote control etc.complete in all respect of following capacity unit: 17.0 TR DUCTABLE UNIT

11.0 TR DUCTABLE UNIT

2.5 TR DUCTABLE UNIT

2.0 TR WALL MOUNTED UNIT

1.5 TR WALL MOUNTED UNIT

Supply and installation of copper refrigerant piping of required sizes duly insulated with closed cell elastomeric insulation thickness as specified by manufacturer,as per pipe size and cabling between indoor and outdoor complete with proper supports etc for following capacity unit. All related civil work such as making hole, chasing in wall, shall be inclusive in the quoted price. 17.0 TR DUCTABLE UNIT

11.0 TR DUCTABLE UNIT

2.5 TR DUCTABLE UNIT

2.0 TR WALL MOUNTED UNIT

1.5 TR WALL MOUNTED UNIT

To supply, install, test and commission UPVC drain pipes duly insulated with 6 mm thick nitrile rubber and 'U ' traps from indoor units to nearest drain point. 32 mm dia.

25mm dia.

AIR DISTRIBUTION SYSTEM Supply, installation, testing and commissing of INLINE FANS for Exhaust air system. Each fan shall be complete with totally enclosed fan cooled motor, drive, motor mount & vibration isolators With Flexible connection. Fan static pressure shall be 20 mm WG. (make: Air Flow) 150 CFM

300 mm dia 1400 RPM fan suitable for 220 +(-)6% volts 50 cycles, 1 Phase AC supply

450 mm dia 1400 RPM fan suitable for 220 +(-)6% volts 50 cycles, 1 Phase AC supply

SMOKE EXTRACTION FAN Supply, installation, testing and commissing of TUBE AXIAL FANS for SMOKE Extraction. Each fan shall be aerofoil impeller, adjustable pitch angle, Suitable for operating temperatures of up to 400°C/120 min.complete with Motors IP55 insulation class H With Flexible connection. Motor shall be suitable for 415 +(-)10% volts, 50 cycles, 3 Phase AC supply and shall be mounted outside air stream. Fan static pressure shall be 20 mm WG. Make- Maico, Lau, Kruger, Nikotra. 12000 CFM

DUCT Supply, fabrication, installation, and testing of site Fabricated ducts of following thickness including necessary supports flexible hangers with isolators, nut bolts, gasket, splitter damper,duct dampers, vanes, etc. complete as per specifications in accordance with the approved shop drawings. AC DUCT 24 gauge galvanised sheet (0.63 mm)

22 gauge galvanised sheet (0.80 mm)

VENTILATION DUCT 24 gauge galvanised sheet (0.63 mm)

22 gauge galvanised sheet (0.80 mm)

FLEXIBLE CONNECTION Supply, fabrication, installation, and testing of canvas flexible connection constructed of fire resistant material as per the drawings /specifications.

GRILLE / DIFFUSER Supply, installation, testing and commissioning of terminal air distribution equipment as per approved shop drawings, colour and specifications. Powder Coated aluminium linear/square grille with aluminium damper.

Powder Coated aluminium linear/square grille without damper.

Exhaust/ fresh air louvers with gravity & bird screen.

Fire Damper Fusible linked type

Aluminium powder coated air grille with damper for exhaust of 100 x 100mm

THERMAL INSULATION ACOUSTIC LINING (DUCTS) : Supply, installation & testing of nitrile rubber/sound absorbing sheet (Density 140-180 kg/m³ ) in supply air ducts , as per specifications. 10 mm thick

DUCT INSULATION Supply, installation & testing of duct insulation with 9mm thick Nitrile Rubber insulation (Density 50-60 kg/m³ ) on supply air ducts. 9 mm thick

SH:- FIRE FIGHTING WORKS:

Supply, Installation, Testing & Commissioning of: Single headed, SS/ Gun Metal ISI marked oblique pattern hydrant landing valve with 80 mm dia flanged inlet and 63mm dia instantaneous type female outlet complete with Gun Metal cap and G.I. chain, twist release type plug and all accessories as per 13:5290-1983 (Type 'A')

Supply, Installation, Testing & Commissioning of: First-Aid Fire Hose Reel wall mounting swinging type complete with drum, bracket, ball valve and 20mm dia.x 30M long high pressure Hose Reel tubing as per IS:444 with Gun Metal shut-off nozzle having 5mm dia. orifice. The Hose Reel shall strictly confirm to IS : 884-1985

Supply, Installation, Testing & Commissioning of: Non-percolating flexible hose (RRL type-'A') ISI marked (IS:636) 63 mm dia x 15 M long complete with instantaneous type SS/ Gun Metal 63 mm dia. IS marked Male and female couplings (IS:903) bound and riveted to hose pipe with Gun Metal rivets and 1.5 mm Gun Metal wire

Supply, Installation, Testing & Commissioning of: SS/ Gun Metal 63mm dia short size branch pipes with 20 mm dia nozzle with 63mm instantaneous coupling ISI marked (IS: 903)

Providing & fixing standard fireman's axe with heavy insulated rubber handle.

Supply, Installation, Testing & Commissioning of:M.S. hose door fabricated from 16g M.S. sheet with full glass door and locking arrangement, suitable to accommodate 1 Hydrant landing valve, 1fire hose reel, 2 nos.15m long 63mmdia hose,1-branch pipe. The door shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx. size 1.2m x .6m x 2.1m )

SUPPLY, INSTALLATION, TESTING & COMMISSIONING of Mild Steel pipe (IS:1239 Part-I) heavy class including cutting, threading, welding etc. bends, elbows reducers, clamps, hangers etc.including cutting holes in brick or RCC walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including all steel work. 80 mm dia IS 1239

100 mm dia IS 1239

150 mm dia IS 1239

Supply, Installation, Testing & Commissioning of slim seal dual type non-return valves (PN 1.6) complete with matching flanges, rubber insertion, nuts, bolts and washer etc. of following sizes. 100 mm dia

Providing and fixing Slim seal Butterfly valves (PN 1.6) complete with matching flanges rubber insertion, nuts. bolts and washer etc. of following sizes 100 mm dia nominal bore

Supplying, Installation, Testing and Commissioning of orifice plate made of 6 mm thick stainless steel with orifice of required size in between flange & landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 kg/cm2 complete with rubber gasket, GI bolts, nuts, washers etc. as required.

Providing and fixing of automatic air vent valve for vertical risers & pipelines.

Supply,Installation,Testing & Commissioning of fire pump on terrace as per specification horizontally mounted centrifugal type for building and capable to deliver approax 900 LPM against a total head of 35M having cast iron body.Bronze impeller, stainless steel shaft and complete with 'Y' strainer on the suction side,butterfly valve on suction and delivery side,non return valve on delivery side and Pressure Gauge with stop G.M. Stop Valve etc. for periodical testing of the working of the pumping set and Suitable RCC Pump foundations as per manufacturer's design 4 Nos Dunlop Anti-vibration (cushy foot) heavy duty mounting pads including all kinds of accessories & valves required for terrace pump installation complete in all respect.

Supply and fixing of ISI marked ( IS : 15683 ) ABC (Dry Powder) fire extinguishers cap 10 kg (9Kg) in seamless HP steel cylinders ISI marked and approved by CCE Nagpur fitted with pressure indicating gauge, internal tube squeeze level type valves fully charged with ABC powder and pressurized by Nitrogen complete in all respects including wall suspension bracket.

Supply and fixing of ISI marked (IS:2878) Portable fire Extinguisher, Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia. 1m long & complete in all respects including initial fill with CO2 gas conforming to IS:307-1966 filled to a filling ratio of not more than 0.667and wall suspension bracket. Capacity 4.5 Kg

SH:- LOOSE FURNITURE:

Providing & Fixing of Push Back Auditorium Chairs suitable for installing in 900mm tread, made as per Fire Safety Norms and Standards, with maximum lumbar support for fatigue free healthy seating, engineered for ergonomic shape, environment friendly with no wood used & CFC free, having 25mm x 5mm MS Flat made back inner frame with 3 serpentine springs, PPCP Plastic molded one-piece inner seat frame, Molded Polyurethane foam cushioned seat back, Upholstered with Flame Retardant Fabric with Scothgard for Stain Resistance, Zipper attached to seat back fabric for easy removability, epoxy powder coated paint for all steel parts, Integrated skin type PU foam made arm rest without cup holder, Maintenance free Synchronized Push back system, with seamless seat supporting tray, Heavy gauge CRC Sheet made side stand covered with fabric - 4.5 Kg, Back side of the back covered with PPCP Plastic back cover, Chairs installed to the floor with expanded anchor fasteners including accessories like Seat number, Gangways & Aisle light boxes etc. complete is all respect as directed and in color shade approved by the consultant (Make: Any Standard)

Providing & supplying Factory Made Two Seater Sofa in composite Leather. The Vendor needs to show one Mock up for approval to proceed further. (Make: Any Standard)

Providing & supplying Factory Made Three Seater Sofa in composite Leather. The Vendor needs to show one Mock up for approval to proceed further. (Make: Any Standard)

Providing & supplying Factory Made approved center / side table. The Vendor needs to show one Mock up for approval to proceed further. (Make: Any Standard) Dia: 600mm

Providing & fixing custom made conference table (design as per drawings) with 19 mm & 12mm board of green/century/Austin make to be with century/green laminate finished with MS leg support . Inside surfaces to be finished with laminate (Make: Any Standard make allow)

Conference Chairs ( (Make: Any Standard) : Kareena High Back

Single seater sofa (Make: Any Standard)

SH:- AUDIO VISUAL WORKS:

Supply, Installation, Testing & Commissioning of Main FOH 2-Way, Bi-amp/Passive Dual Concentric Driver Speaker Cabinet having Transducer Size :Transducer Size : 1 x 12" LF; Power Handling : HF - 80 Watts Continuous, 320 Watts Peak | LF - 350 Watts Continuous, 1400W Peak ; Freq. Range : 80 Hz - 25 kHz; Dispersion : 75 degree conical ; Sensitivity : Passive - 97 dB | LF - 98 dB : HF - 106dB, Max Peak SPL - 129 dB. Approved Makes: Martin Audio/ Music Tribe/ D&B Audiotechnik

Supply, Installation, Testing & Commissioning of 1x18" Subwoofer having 18" long excursion transducer; TTransducer Size : 1 x 18" Power Handling : 800 Watts Continuous, 3200W Peak; Freq. Range : 38Hz - 220 Hz Dispersion : Omni-directional; Sensitivity : 97 dB; Max SPL : 126dB continuous, 132 dB peak Approved Makes: Martin Audio/ Music Tribe/ D&B Audiotechnik

Supply, Installation, Testing & Commissioning of Line Array Frames for the aforementioned speakers

Supply Installation Testing Commisioning of a Gooseneck microphone with table stand : Cardioid Condenser Gooseneck Microphone. with Frequency Response 100 - 16,000 Hz; Open Circuit Sensitivity: -43 dB (7.0 mV) re 1V at 1 Pa, Impedance 250 ohms or better completew with Foam Windscreen. Anti-Shock Microphone Stand with on/off Switch . Approved Makes: Audio Technica/ Sennheiser/ Earth Works

Supply, Installation, Testing & Commissioning of UHF Wireless Cardioid dynamic handheld microphone system with Frequency Response of 100 Hz to 15 kHz (+1 dB, -3 dB), RF Sensitivity 20 dBuV at 60 dBA S/N ratio (50Ω termination), Total Harmonic Distortion <1.0% (at 1 kHz, ±20 kHz deviation) , Dynamic Range > 110dB , on/off switch, RF Power Output High: 30 mW, Low: 10 mW (switchable) at 50 Ω , Multiple band with 10 channels on each band ; maximum Output level XLR / Balanced: +9 dBV & 6.3 mm (¼"") / Unbalanced: +4 dBV. Approved Makes: Audio Technica/ Sennheiser/ Earth Works

Supply, Installation, Testing & Commissioning of UHF Wireless Cardioid Cardioid condenser lavalier microphone with 55" cable terminated with locking 4-pin HRS-type connector, Frequency Response of 100 Hz to 15 kHz (+1 dB, -3 dB), RF Sensitivity 20 dBuV at 60 dBA S/N ratio (50Ω termination) , Total Harmonic Distortion <1.0% (at 1 kHz, ±20 kHz deviation) , Dynamic Range > 110dB , on/off switch operating range 100 mtrs , RF Power Output High: 30 mW, Low: 10 mW (switchable) at 50 Ω , Multiple band with 10 channels on each band ; maximum Output level XLR / Balanced: +9 dBV & 6.3 mm (¼"") / Unbalanced: +4 dBV. Approved Makes: Audio Technica/ Sennheiser/ Earth Works

Supply, installation, testing and Commissioning of Digital Mixer : Compact 40-Input, 25-Bus Digital Mixing Console with 16 Programmable Midas Preamps, 17 Motorized Faders, Channel LCD's, 32-Channel Audio Interface and iPad/iPhone* Remote Control, 8 XLR outputs plus 6 additional line in/outputs, 2 phones connectors and a talkback section with integrated or external mic, High-resolution 7" day-viewable Color TFT , Main LCR, 6 matrix buses and all 16 mix buses each featuring inserts, 6-band parametric EQ's and full dynamics processing, plus 8 DCA and 6 mute groups. Approved Makes: Behringer/Digico/Midas

Supply Installation Testing & Commissioning of a 2.5 Sq. mm, 2 Core Speaker Cable having Core Arrangement : 2,Gauge : 2.5 sq. mm,Material : Stranded Bare Copper - Oxygen Free,Shielding : Unshielded, Jacket Material : TPR, Bend Radius: 4x Diameter Approved Makes: Krystal/Netmass/ Klotz/Belden/A&T

Supply , installation , testing and commissioning of UL Listed Connectors as per the tender specifications

Supply Installation Testing & Commissioning of Mic Stands Big, with boom arm

Supply Installation Testing & Commissioning of Mic Stands Small, with boom arm

Supply, Installation, Testing & Commissioning of of 18 U Rack with wheels. Approved Makes: Valrack/Rittal/Equivalent

SH; VISUAL WORKS

1-chip DLP LASER Phosphor Multimedia Projection system having, 7000 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3D ready, 1200000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 1.25-2.0 lens & projector mountin bracket etc. Approved Makes: Christie/Barco/NEC

25x16 ft Fixed Screen CInema White Perforated Fabric. Cyclorama Screen should in accordance with DIN 4102-1 Class B2 materials, Screen Can Sustain temperature of 23 ± 2 °C, and a relative humidity of 50 ± 6 % and have a Mild Dew Resistant property. The Frame Should Be Made up of High Grade Aluminum with Velvet Coated, Screen Fabric should be 100% Seamless and have Perforation, The Frame Should have Lungs installation system for Fabric Placement and should not use any Spring usage to avoid damage to Screen, Screen Fabric should meet the requirements of Class B2 of building materials. Approved Makes: Suvira/Equivalent/Swastik

SITC of Wallplate TX/RX kit HDMI Over HDBaseT TX Wallplate/RX with USB, Control, PoE and HDMI, 2K and 4K support, HDTV Compatible, HDCP Compliant complete as required. Approved Makes: Extron / Kramer/ Lightware

SITC Distribution amplifier : 1×4 HDMI® distribution amplifier, 4K/UHD capability @ 60 Hz with 4:4:4 chroma sampling, plus support for HDR formats, HDCP 2.2 compliant, EDID management. Approved Makes: Extron / Kramer/ Lightware

SITC of Wireless Presenter moduleAllows simultaneous present upto 4 or more screens at the same time,Allows a user to manage on-screen presenters as well as queued presenters ,AES67 Networked audio interfacing for integration with DSPs and audio over IP systems,Integrated WI-FI Access Point – can be segregated from the facility LAN for security reasonsShall be having provision for being used as a digital signage media player (additional hardware and software may be added to achieve the same)Shall have functionality to support streaming like Youtube streaming for archival and viewing purpose,Dynamic Layout Mode - automatically adapts to incoming or disconnected source contentWireless screen casting through native AirPlay, Google Cast, or Miracast protocols Approved Makes: Extron / Kramer/ Lightware

SITC of Controller : Hardware server gateways for AV system control, room scheduling, and AV asset management, Access from a web browser for setup and management, Simplify system or device configuration, deployment, and management with the interactions, flow, and visual elements of a web or mobile app GUI, Atlona Management System (AMS) for configuring Atlona devices over the network, Velocity Cloud, Lite remote configuration and management, Dual Gigabit Ethernet ports for isolating a dedicated AV LAN from the facility or corporate network, Supports industry-standard, network security features and protocols. with RS232 and Relay controlls. Approved Makes: Extron / Kramer/ Lightware

SITC of 10" Tablet. Approved Makes: Apple / Samsund or equivalent

SITC of PTZ Camera with HDMI Output and USB : Designed for video conferencing and other applications such as lecture capture and distance education, HDMI output, USB 2.0 interface for video and camera control, Universal PC compatibility through standard UVC (USB Video Class) driver, High performance imaging, fine detail, and color rendering with 1/2.8″ low-noise, HD CMOS sensor, Multi-element zoom lens with 10x optical zoom and a 60.9° horizontal field of view. Approved Makes: Extron / Kramer/ Lightware

SITC of Wi-Fi router, 4 LAN ports, 1 Gbps bandwidth, with power adaptor.

Supply and Laying of 4.6 Metres HDMI patch cord in existing conduit.

Supply and Laying of 1.8Metres HDMI patch cord in existing conduit.

Supply and Laying of 1.8Metres HDMI to DVI patch cord in existing conduit.

Supply and Laying of HDBaseT recommanded 23 AWG shielded CAT6A Cable with appropriate connectors in existing conduit.

Supply and Laying of sheiled connector for 23 AWG shielded CAT6A Cable.

M/S Agam Constructions