PROVN OF STORE ROOM AND VEH PARKING SHED AT ASCON NODE OF SUB GP SECURITY WALL NEAR OTM AT NCCIU ADDN/ALTN IN BATHROOMS AND SEWAGE LINES WITH ALLIED INFRA IN BLDG NO P-03 BLDG NO NP-126 BLDG NO P-04 (UNDER GROUND OPS ROOM) AT HQ NORTHERN COMMAND

Amount

Taking down cement plaster and raking out joints, hacking for key, scrubbing down with water built in cement mortar complete all as specified and directed.

Rendering 15 mm thick in cement mortar 1:6 on fair faces of brick/concrete finished even and smooth without using extra cement complete all as specified and directed.

Preparation of new plaster surface of walls and applying two coats of oil bound distempers over one coat of primer and two coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 on vertical surfaces/backing coat complete all as specified and directed.

Glazed ceramic coloured tiles of size 600 x 300 x 7-8 mm wall tiles set and jointed in neat cement and in white/coloured cement to match with the colour of tile etc complete all as specified and directed.

Demolition of cement concrete any description and any position not otherwise specifically provided complete all as specified and directed.

75 mm thick PCC 1:4:8, type D-2 (by using 40 mm graded stone aggregate) as in sub base floor complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in level course on floor etc complete all as specified and directed.

15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor complete all as specified and directed.

Non skid coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Vitrified ceramic tiles (Double charge), area of each tile not exceeding 0.36 sqm, 10 mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

All as per ser item No 12 but in vertical surfaces such as skirting/dado etc complete all as specified and directed.

Vitreous china ware wash down water closet pan, (pedestal pattern) coloured including connection to drain and to flushing pipe, anti syphonage pipe etc.as in repair complete all as specified and directed.

WHB vitreous china (flat back or angle back type) any size, including cutting for pinning in ends size 550 x 400 mm including brackets, 32 mm CP waste fittings coupling, connection pipe 450 mm long and 15 mm dia CP piller taps fancy type complete all as specified and directed.

10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified and directed.

Plastic water closet seat, black or white closed pattern, solid type with flat bottom, and cover and mild steel chromium plated hinging device (Make : CERA) any type of EWC complete all as specified and directed.

Pillar tap cast copper alloy with capstan head, chromium plated screwed down high presure with or with out lettered fixed with iron pipe complete all as specified and directed.

Bib taps cast copper alloy with crutch or butter fly handle screwed for iron pipe of dia 15 mm fixed as in repair complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 1000 ltrs (cylindlerical verrtical with closed top) hoisted and fixed in position complete all as specified and directed in SSR part I including dismantaling of existing damaged water tanks.

Steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 15 mm bore including taking down old pipe complete all as specified and directed.

Steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 20 mm bore including taking down old pipe complete all as specified and directed.

Health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe complete all as specified and directed. Make : CERA Cat Part No F8030103 and equvalent in CERA.

Chromium plated toilet paper holder complete all as specified and directed. Make : Jaquar Cat Part No ACN 1153N and equvalent in CERA.

Glass shelf with chromium plated guard rails complete all as specified and directed. Make : Jaquar Cat Part No ACN-1171N and equvalent in CERA.

600 mm long brass chromium plated towel rail fancy type complete all as specified and directed. Make : Jaquar Cat Part No ACN-1111NM and equvalent in CERA.

Soap dish complete all as specified and directed. Make : Jaquar Cat Part No ACN 1131N and equvalent in CERA.

Gun metal globe or gate valves high pressure with polythene float and fly nut complete screwed for iron pipe or for unions of 20 mm bore and complete all as specified and directed.

Stop valves cast copper alloy chromium plated fancy type, screwed both ends for iron pipe 15 mm bore complete all as specified and directed.

Excavation in post holes each not exceeding 0.50 cum getting out, returning filling in and well ramming earth around in layers not exceeding 25 cm, watering and removing surplus soil to a distance exceeding 1.5 kilo mtr and making good distrub surfaces as in hard/dense soil complete all as specified and directed.

Plain cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in post hole, foundation and similar work etc complete all as specified and directed.

Roof trusses (framed) trussed, purlins, crane gantries rails and fastenings and heavy brackets, post and similar work framing (beam, tee, channel or flat sections) including distance pieces cleats, MS plat including welding reavrign etc. complete all as specified and directed.

Pre-painted galvatume aluminum zinc coating GI vased corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

Taking down frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm Each including iron mangery complete all as specified and directed.

PVC moulded door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing complete all as specified and directed.

Butt hinges 100 mm size extruded aluminium alloy with galvanised mild steel hinge pin anodised complete all as specified and directed.

150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

150 mm length aluminium handles fabricated type anodised complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exceeding 15 cm thickness below and above ground level complete all as specified and directed.

Sand cushion 20 to 30 mm thick for laying and fixing interlocking tiles complete all as specified and directed.

Machine pressed precast concrete interlocking paver block (glossy finish) any shape and size (sample approved by GE) confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed by Engr-in-Charge.

Precast cement concrete (factory made) 1:2:4 type B-1 (20 mm graded stone aggregate) set in cement mortar as in road kerbs and similar work etc complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation or manholes etc and area not exceeding 10 Sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete type D-2 (1:4:8) for 150 mm dia pipe complete all as specified and directed.

SWG drain pipe grade 'A' of 150 mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:4) as in manholes, septic tank, filter bed, walls, drains etc complete all as specified and directed.

Cement concrete type D-2 (1:4:8) (using 40 mm graded stone aggregate) as in foundation filling and mass concerete complete all as specified and directed.

Rendering 15 mm thick on brick or concrete surfaces of walls in cement moratr (1:4) including finishing the surfaces even and smooth without using extra cement as in manholes, septic tank, filter bed out let drain etc complete all as specified and directed by Engineer-in-Charge.

Precast reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) for manhole cover septic tank covers slabs etc including necessary form work and set in cement moratr (1:4) complete all as specified and directed. Note:- reinforcement will be measured and paid seperately.

TMT bars 10 mm dia and over and cut to length bent to shape required including cranking, bending, hooking ends and bending with MS wire not less than 0.9 mm dia or securing with clips quality confirming complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls bore of the pipe 110 mm complete all as specified and directed.

PVC (SWR) vent cowl 110 mm dia complete all as specified and directed.

Soakage wells excavation,1.8 M dia x 3.0 M effective depth in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats. complete all as specified and directed by Engr-in-Charge.

Returning, filling in with approved soil obtained from excavation including spreading levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing excavated soil to a distance exceeding 50 m and not exceeding 1.50 km out side defence land complete all as specified and directed by Engr-in-Charge.

Excavation over areas not exceeding 1.5 m deep and getting out as in soft/loose soil complete all as specified and directed.

100 mm PCC 1:4:8 type D-2 (40 mm graded stone aggregate) as in foundations and mass concrete complete all as specified and directed.

Brick work with sub class "B" bricks straight or curved on plan exceeding 6 meter mean radius in cement mortar 1:6 complete all as specified and directed.

Form work to sides of footings, rough finished flat surfaces complete all as specified and directed.

Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars and similar work confirming to E-250 complete all as specified and directed.

Form work to sides of columns etc rough finished surfaces complete all as specified and directed.

RCC M 25 design mix (RMC) (using 20 mm graded stone aggregate) as in footing complete all as specified and directed.

Broken glass coping on top of walls, embedded in cement mortar 1:3 complete all as specified and directed.

RCC M 25 design mix (RMC) (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

Mild steel TMT bars 12 mm dia and over cut to lenth, bent to shapr required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Mild steel TMT bars 6 to 8 mm dia as in reinforcement cut to length, bent to shape required, including cranking, bending spirally for hooking for columns, hooking ends and binding with and icnluding mild steel wire (anealed not less than 0.9 mm dia) complete all as specified and directed.

Rendering 5 mm thick using cement mortar 1:4 on fair faces of brick work or concrete surfaces even and smooth without using extra cement complete all as specified and directed.

Applying two coats of cement base paint over a coat of white wash including preparation of old plastered surfaces complete all as specified and directed.

Roughening surfaces of old concrete floor by picking sweeping cleaning & washingg down with water to remove dust etc including removal of old treatment of any description and applying one coat of neat cement slurry @ 3.00 kg/Sqm complete all as specified and directed by Engr-in-Charge.

PCC 1:2:4 type B-1 (using 12.5 mm graded aggregate) as in level course on roof surface 25 mm thick etc complete all as specified and directed.

Rendering 10 mm thick in cement mortar 1:3 mixed with integral water proofing compound as per manufacture's instructions as in roof and chajjas, finished the surface fair and even with out using extra cement complete all as specified and directed. Note : Supply of water proofing compound will be measured and paid separately.

Applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide modified polymeric five layered APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polythylene film. Minimum weight of memebrane will be 3.5 kg/sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm blinded with fine sand in dry condition @ 0.5 kg/sqm including two coats of bituminious alluminium paint complete all as specified and directed by Engr-in-Charge.

110 mm PVC (SWR) bends any redius with access door complete all as specified and directed.

110 mm PVC (SWR) couplers for PVC pipe and similar work complete all as specified and directed.

105 x 60 mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer complete all as specified and directed.

Factory made 35 mm thick 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35 mm thick complete all as specified and directed by Engr-in-Charge.

Preparation of new wooden surfaces of any description, not other wise described over 10 cm width or girth applying two coats of synthetic enamel paint over a coat of primers complete all as specified and directed.

100 mm size mild steel butt hinges medium weight cold rolled complete all as specified and directed.

300 mm long aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

Dismantlling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverrings complete all as specified and directed.

Pre-painted galvatume aluminum zinc coating GI vased Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

Complete removal of existing treatment and applying two coats of oil bound distemper over a coat primers with two coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster on brick or stone masonry wall etc including racking out joints haking for key, scrubbing down with water etc as in external surfaces of man holes, septic tank, filter bed etc including removing of debrie complete all as specified and directed.

Vitreous China two piece EWCs water closet pedestal pattern colour (as approved by Engineer-in-Charge) with 'S' Trap 100 mm, flushing cistern, seat cover and twin flush fittings complete all as specified and directed by Engr-in-Charge. Make : CERA (Model - Cat Part No (EWC S 1013106S Trap 255 mm) or equivalent model of makes specified in PS.

Large urinal large 420 x 395 x 635 mm complete all as specified and directed by Engr-in-Charge. Make : CERA Cat Part No S4020102 or equivalent model of makes specified in PS.

Chromium plated bottle trap with internal partition complete all as specified and directed by Engr-in-Charge. Make : Cat Part No ALD 769L250X190 or equivalent model of makes specified in PS.

750 mm x 450 mm Urinal partition made up of 10 mm thick glass duly sand blasted including stainless steel holding clamps, complete all as specified and directed by Engr-in-Charge.

Bib cock with flange to 15 mm bore pipe, complete all as specified and directed by Engr-in-Charge. Make : Jaquar, Cat Part No KUB 35037F or equivalent of makes specified in PS.

15 mm bore brass CP angular stop cock with wall flange complete all as specified and directed by Engr-in-Charge. Make : Jaquar, Cat Part No - KUB35053F or equivalent of makes specified in PS.

Brass chromium plated toilet paper holder with flap complete all as specified and directed by Engr-in-Charge. Make : Jaquar, Cat Part No AKP-35753P or equivalent of makes specified in PS.

Sensor type pillar tap (Sensor faucet) for wash hand basin Square in shape with base flange complete all as specified and directed by Engr-in-Charge. Make : Jaquar Cat Part No SNR-CHR 51033 or equivalent of makes specified in PS.

15 mm bore center hole basin mixer with regular spout with pop up waste assembly with 10 mm dia 450 mm long braided hoses and brass nuts complete all as specified and directed by Engr-in-Charge. Make : Jaquar Cat Part No KUB-35169FB or equivalent of makes specified in PS.

Hand shower (health faucet) brass CP with 8 mm dia 1.0 meter long flexible tube with wall hook with NRV (Back flow preventor) complete all as specified and directed by Engr-in-Charge. Make : Jaquar Cat Part No ALD - 577 or equivalent of makes specified in PS.

Brass CP waste coupling Clikc Clack 32 mm bore (half or full threaded) minimum weight 450 gms complete all as specified and directed by Engr-in-Charge. Make : Jaquar Cat Part No ALD -727 or equivalent of makes specified in PS.

Taking down chowkhats with shutter (without taking off from shutter) exceeding 1.5 sqm and not exceeding 4 sqm each complete all as specified and directed.

Aluminium powder coated frame suitable for sliding/openable/fix, doors, windows, ventilator, guard bar, grill and similar work with one or more rebates including joining cleat for fixing etc omplete all as specified and directed.

Sheet glass quality 5 mm thick in squares not exceeding 0.5 sqm each pane and glazing incl all fitting and obscured or frosted on one side fixed complete all as specified and directed.

12 mm thick toughened glass door with and including heavy duty floor spring top hinge including pivot clamps, side locking arrangement, stain less steel 300 to 400 mm long handles complete all as specified and directed by Engr-in-Charge.

Itching to toughened glass to required design complete all as specified and directed by Engr-in-Charge. Note : Glass has to be paid and measured for seperately.

Sand blasting to glass of approved design and pattern complete all as specified and directed by Engr-in-Charge. Note : Glass has to be paid and measured for seperately.

All as per ser item No 104 but as in skirting and similar work complete all as specified and directed.

75 mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement in repair complete all as specified and directed.

75 mm PVC (SWR) pipes single socket in any lenth with rubber ring joints fixed to wall complete all as specified and directed.

75 mm PVC (SWR) bends any redius with access door complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, settting and jointing with solvent cement in repair complete all as specified and directed.

1 mm thick stainless steel plate rack of size 900 x 750 mm of approved make and quality complete all as specified and directed by Engr-in-Charge.

Sinks with drainage board made of stainless steel 1 mm thick kitchan or laboratary with plugs washers and westes, including bedding in cement mortar to drawft wall or including fixing cantilevers bracket and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

20 mm ball valve high pressure with polythylene float valve and fly nut complete screwed for iron pipe PTMT complete all as specified and directed.

Gun metal globe or gate valve 15 mm, with iron wheel head screwed both ends for iron pipe and loud in repairs complete all as specified and directed.

WHB coloured 550 mm x 480 mm with Pedestal, Make : CERA Cat Part No (S2040115 & S2090111) (as approved and complete all as specified and directed by Engineer-in-Charge.

All as per ser item No 114 but exceeding 1.5 mtr and not exceeding 3 mtr deep complete all as specified and directed.

Septic tanks exceeding in ordinary soil, foundation in PCC 1:2:4 rick work in cement mortar 1:4, RCC slab covers including RCC precast manhole covers having 6 mm plat embedded all around/fiber reinforced cover with angle iron frame vent shaft and sludge chamber etc complete for 100 uses complete all as specified and directed.

Demolition of old existing septic tank/soakage well with and including of raw/dissolved sewage (if any) and removing the deberis out side the defence land and refilling the existing surface with soil to match the sorrounding area complete all as specified and directed by Engr-in-Charge.

Stone masonry random rubble un-coursed well bounded bedded and solidly hearted in cement mortar 1:6 complete all as specified and directed.

Cement concrete type B-1 1:2:4 (using 20 mm gradded aggregate) use in coping, hold fast and similar work including naccesary form work complete all as specified and directed.

Precast cement concrete louvres and jallies 50 mm thick set in cement mortar 1:6 type B-0 (1:2:4) (using 12.5 mm graded aggregate) etc sample as approved by GE. complete all as specified and directed by Engr-in-Charge.

Reinforced cement concrete (nominal mix) type B-1 1:2:4 (20 mm graded aggregate) using in beams, cantilevers, bressummers, lintels over 1.5 mtr span and similar work etc. complete all as specified and directed.

Form work to sides of lintels, beam haunching, girders lintal cantiliver including supports overhung etc complete all as specified and directed.

Rendering 5 mm thick in cement mortar 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete all as specified and directed.

Raised pointing to random or polygonal rubble masonary coursed or un coursed in CM (1:3) complete all as specified and directed.

Preparation of new plastered wall surface and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Precast cement concrete 1:3:6 type C-1 (20 mm graded stone aggregate) as in bond stone complete all as specified and directed.

Framed work such as doors, gates of angle or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding eith and including either hooks and hinges or steel hanging door fittings including ornament and intricate design, including pintle hings, stops hand made sliding bolts etc confirming to Fe 290 Gde-E-165 complete all as specified and directed.

Preparation of new steel surfaces of any discripton not otherwise discribed over 10 cm width or girth and applying two coats of synthetic enamal paint over a coat of red oxide on steel surfaces complete all as specified and directed.

20 mm thick granite (of any type) machine cut as in dado etc laid over cement backing coat and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grainding and polishing complete all as specified and directed by Engr-in-Charge.

75 mm thick PCC 1:5:10, type E-2 (by using 40 mm graded stone aggregate) as in sub base floor complete all as specified and directed.

10 mm thick screed bed in cement mortar 1:4 for laying floor finishes under floor complete all as specified and directed.

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirm Fe 410 W (Gde-E-250) qty A complete all as specified and directed.

Taking down frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm Each including iron mangery complete all as specified and directed.

Aluminium powder coated door shutters, aluminium section weighing 0.55 Kg/m including necesssary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door hinges,&tower bolts powder coated aluminium snap beading screws etc complete all as specified and directed.

Aluminium powder coated window and ventilator shutters, fixed type without sash bar aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips rubber packing anodised alu snap beading screws etc complete all as specified and directed.

Sheet glass ordinary quality 4.8 mm thick (tinted/plain) and glazing with oil putty in squares exceeding 0.5 sqm each pane fixed complete all as specified and directed.

Galvanished mild steel wire cloth 0.56 mm nominal dia of wire and average width of apperature 1.18 mm complete all as specified and directed.

Vertical venetion blinds fancy type 100 mm wide light coloured fitted with connecting strings suspending steel plates and guide rails and sliding rollers complete all as specified and directed by Engr-in-Charge. Make : Vista or equivalent as approved by GE.

Complete removal of existing treatment from external surfaces of walls by wire brushing and washing, rubbing down and stopping of surfaces and leveling/edging the disturbed planes/edges using necessary filling compound of Altek putty to obtain smooth regular/even finish using sand paper and applying two coats of exterior emulsion paint 1st quality (Apex of Asian Paints or equivalent in Berger/Shalimar) paint complete all as specified and directed by Engineer-in-Charge. The tint/shade of the paint shall be as approved by the GE.

Door closer hydraulically regulated, designation no 2 universal type suitable for door shutter of 701 to 850 mm in width and of weight between 36 to 60 kg aluminium (extruded section) body complete all as specified and directed.

PVC wall lining consisting of 5 mm thick plain colour pvc sheet inclusive of solvent cement and fixing at site on pvc frame as per site requirement complete all as specified and directed by Engr-in-Charge.

10 mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing to wall to make pvc frame as per site requirement. complete all as specified and directed by Engr-in-Charge.

Cutting holes in brick wall exceeding half brick but not exceeding one brick built in cement mortar or cement lime morter and stone wall built in lime morter and making good with dismantled portion in cement mortar 1:3 or cemen concrete 1:2:4 type B-0 complete all as specifed and directed by Engr-in-Charge.

Collapsible gatew, top hung, consisting of channel pickets, pivoted flat bars. Top and bottom runners brass handles etc as specified, erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

20 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor complete all as specified and directed.

Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Rolled mild steel work of angle iron as in frames of doors & Cupboard etc confirming to grade Fe-310-O complete all as specified and directed.

PVC modular Kitchen & Cupboard Shutter of 18 mm thick consisting of panel of hollow PVC profile of 12 mm thickness consisting of M.S. tube of 16 gauge thickness and size 10 mm x 10 m inserted all around the hollow profile section and lipped with 8 mm (4 mm x 2) thick and 12 mm wide on stiles and rails using solvent cement including chromium plated settel handle, magnetic catches including running hinges. The inner panel shall consist of 4 mm/prelam moulded PVC sheet of density 600 kg/cbm density manufactured by an ISO-9000 certified company on the front side & 2 mm Plain/Prelam PVC sheet of density 700 kg/cbm using solvent cement on both side of the panel. The thickness of the shutter is edge lipped by 18 mm width x 1 mm thick PVC sheet using solvent cement etc. complete all as specified and direction of Engr-in-Charge. (Manufacture's specification and drawing) Make : Rajshree/Sintex.

PVC rigid foam sheet wall panelling of 5 mm thick stuck on inner frame work of 35 mm wide strips of 5 mm thick rigid foam sheet. The strips should have a groove of 6 mm width and 2 mm depth for sinking the head CF screw used to fixed the strips to the all and should be placed vertically at intervals of 600 mm c/c. The PVC strips to be fixed to the all using 65 mm long MS screw through the groove in the strips by using PVC fasterners complete all as specified and directed. Make : Rajshree/Sintex.

Stainless steel as in framing for fixing of glazed partition/windows or doors as per site requirement confirming to Gde 304 complete all as specified and directed by Engr-in-Charge.

12 mm thick toughened glass partition work and similar work including SS clamps (as per requirement) side complete all as specified and directed by Engr-in-Charge.

Taking down carefully, copper/aluminum point wiring (light, fan, socket or power/LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and directed. Keeping the LED lights in safe custody.

Point wiring for one light/fan/bell point controlled by one switch using 1.5 Sqmm FRLS copper conductor cables (multistranded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with Modular metal flush boxes thickness (1.25 mm) & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts copper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed.

All as per ser item No 153 but for 3 pin 6 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 153 but for 3 pin 6 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 153 but for 3 Pin 16 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

All as per ser item No 153 but for 3 Pin 15 Amps socket outlet independent with cable 4.0 Sq mm including copper PVC insulated PVC unsheathed 2.5 sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

Switch Piano flush type 6 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed.

Switch Piano flush type 16 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed.

Socket 2-in-1, 3 Pin 6 & 16 Amps (Modular Type) with outer strip complete all as specified and directed.

Ceiling rose surface bakelite 3 terminals complete all as specified and directed. Make : Cona Cat Part No 2126/SSK Cat Part No 572 or equivalent of make in Havells/Anchor/Kolors.

Single pole and neutral enclosure surface mounted 240 volts with 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator of make wipro/equivallent in Havells/Bajaj complete all as specified and directed.

New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 20 W Make - Havells Cat Part No LHEXBXPNIN1W020 or equivalent to Polycab/HPL/Bajaj complete all as specified and directed by Engineer-in-Charge.

30 W LED Flood light Orion 1.0 Series with presure die-cast aluminium housing complete with all accessories Cat Part No LTEFI30WHPLED 30 W Make: C&S or equivalent to Polycab/HPL/Bajaj complete all as specified and directed by Engineer-in-Charge.

Exhaust fan Ventil Air-DB 300 mm including louver complete all as specified and directed. Make - Havells/Polycab/Bajaj.

Replacement of LED bulk head luminaire, 10 W (ENDURA RUGBY) Cat Part No. LHEOAOP7UZ6W010 230 Volts wall/surface mounted complete with with LED lamp 10 watt, with all accessories, pre-wired, including providing flexible copper wire, twin core cable complete all as specified and directed by Engineer-in-Charge.

Surface mounting, 20W, dome shaped pendant in finishes including 7 watt LED bulb complete all as specified and directed by Engr-in-Charge. Make : Havells, Cat Part No -LHFHDPE1TN1G020

Replacement of New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 10 W complete all as specified and directed by Engineer-in-Charge. Make- Havells, Cat Part No LHEXBXPNIN1W010 or equivalent to Polycab/HPL/Bajaj complete all as specified and directed by Engineer-in-Charge.

Socket 2-in-1, 3 Pin 6 Amps (Modular Type) with outer strip complete all as specified and directed.

s l sharma and sons