PROVN OF 01 TOILET BLOCK MALE AND FEMALE AT BLDG NO T 237 AND T 238 ADM BLOCK OF 4 TECH TRG BN SPL REPAIR OF ADM BLOCK BLDG NO 764 ARTIFICER SHOPS OF 21 CGSR A AND SPL REPAIR TO ROOF TREATMENT FLOOR AND TOILET OF P-450 ADM BLOCK OF 102 ENGR RE

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Taking down shutters of any description of area exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down chowkhats or frame n exc 1.5 sqm each with shutters (without taking off shutters from the frame) including fittings complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 sqm but n exc 4.00 sqm each with shutters (without taking off shutters from the frame) including fittings complete all as specified and directed.

S&F of powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters & frames of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket as required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc; aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, CP brass/ stainless steel screws complete all as specified and directed.

S&F of solid PVC door frame of size 50 x 47 mm, made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F of 3 mm thick aluminium composite panels (ACP), exterior grade, PE core, PVDF coated of approved shade and fixed as per manufacturer specifications complete all as specified and directed.

M&L for providing cement concrete, 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in coping, bed blocks, lintels, cills, steps, seismic and other similer bands, kerbs and like etc complete all as specified and directed.

S&F of 100 mm long mild steel butt hinges, medium weight, cold rolled and fixed complete all as specified and directed.

S&F of 150 mm long aluminium handles, cast type, anodised and fixed to shutters complete all as specified and directed.

S&F of 150 mm long aluminium anodised barrel tower bolts, extruded section and fixed complete all as specified and directed.

S&F of 200 mm long aluminium anodised barrel tower bolts, extruded section and fixed complete all as specified and directed.

S&F of 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F of 140 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc; laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 18 to 20 mm thick granite stone slab (any type) (table rubbed and polished) as in steps, jambs, pillars, window & door cills, cooking platforms, counter, shelves and like in cement mortar (1:4) over and including 15 mm thick screed bed in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including making the edges bullnosed complete all as specified and directed.

M&L for 18-20 mm thick machine cut kota stone slab flooring over and including 20 mm thick cement screed base in CM 1:6; laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

Refixing old retrieved Kota stone slab at any location in floors over and including M&L for providing 20 mm thick cement screed bedding in CM 1:6 including grinding and mirror polishing to achieve required finish complete all as specified and directed.

Refixing old retrieved Kota stone slab at any location in skirting over and including M&L for providing 10 mm thick cement screed bedding in CM 1:4 including grinding and mirror polishing to achieve required finish complete all as specified and directed.

M&L for reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) as in coloumns, pillars, posts, struts etc. complete all as specified and directed.

M&L for reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) as in beams, bands, cantilevers, bressummers, lintels over 1.5 m span etc. complete all as specified and directed.

M&L for reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) as in chajjas and similar work complete all as specified and directed.

M&L for reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns complete all as specified and directed.

M&L for reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) as in flooring and similar work complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter surface flat rough finished surface complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, coloumns etc. for flat rough finished surface complete all as specified and directed.

Use and waste of formwork to chajjas including edges for flat rough finished surface complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, bands, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat rough finished surface complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for flat finished surfaces complete all as specified and directed.

Demolition of cement concrete in ground floor (unreinforced) and paving n exc 15 cm thick (below or above GL) including tiling if any complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in sub base of floors to receive finish, finished even and rough complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in plinth protection, aprons, hard standing, path and like; finishing the surfaces even and smooth without using extra cement with and including making the grooves in bays n exc 2 m in length and joints filled with bitmuminous mastic filling in 1:3 complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge n exc 63 mm, deposited spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for anti termite treatment to bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for anti termite treatment to backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for anti termite treatment to top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for anti termite treatment to soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for anti skid ceramic coloured tiles 9 to 10 mm thick (square /rectangular) joint free, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors; over and including 15 mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square /rectangular) joint free, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors; over and including 15 mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified and directed.

M&L for premium double charge glazed vitrified wall tiles 9-10 mm thick (area of each tiles n exc 2.20 sqm each) fixed on vertical surfaces such as skirting, dado etc; set and jointed in neat cement slurry over and including 10 mm thick cement plaster in CM (1:4) and pointed with epoxy tile grout filling of approved make and colour complete all as specified and directed.

M&L for premium double charge glazed vitrified tiles 9-10 mm thick, area of each tiles exc 0.6 sqm but n exc 0.42 sqm each as in floors, fixed with 5 mm spacers set and jointed in neat cement slurry over and including 15 mm thick screed bed in CM (1:6) and pointed with epoxy tile grout filling of approved make and colour complete all as specified and directed.

M&L for designer coloured glazed ceramic tiles in walls/ vertical surface of size 300 x 450 & 7 mm thick over and including 10 mm thick rendering in CM 1:4 for backing of tiles, set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles complete all as specified and directed.

Demolition of brick work, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with fly ash bricks (modular size bricks) straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for brick work with fly ash bricks (modular size bricks) straight or curved on plan any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces, including racking out joint, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:3 on brick/concrete ceiling surfaces, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:6 on brick/concrete surfaces, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:6 on brick/concrete surfaces, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:4 on brick/concrete/stone masonary surfaces, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on brick/concrete/stone masonry surfaces, finishing the surfaces even and smooth without using extra cement including taking out old plaster complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on brick/concrete/stone masonry surfaces, finishing the surfaces even and smooth without using extra cement including mixing water proofing compound complete all as specified and directed. Note: WPC will be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

Complete removal of existing treatment of wall surfaces with and including M&L for preparation of old decorated surfaces of walls and applying two coats of oil emulsion distemper complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper over a coat of wall primer complete all as specified and directed.

M&L for applying a coat of 2 mm thick white wall care cement based water proof putty in two layers on walls/ ceiling, finshed even and smooth complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic smooth exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS: 15489 : 2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new wall surfaces complete all as specified and directed.

Complete removal of existing treatment from walls with and including M&L for applying two or more coats of 100% premium acrylic smooth exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS: 15489 : 2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over wall surfaces complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceilings and applying two coats of white wash complete all as specified and directed.

S&F of 4.8 mm thick sheet glass, ordinary quality and glazing with rubber gasket in square exceeding 0.5 Sqm in each pane for aluminium window, door, ventilator complete all as specified and directed.

S&F of aluminium (Extruded section body) door closer hydraulically regulated, designation No. 3, universal type suitable for door shutters of 851 to 1000 mm in width and of weight not more than 61 to 80 kg and fixed complete all as specified and directed.

S&F in repairs stainless steel toilet paper holder, D type and fixed with screws complete all as specified and directed.

S&F of stainless steel soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F of vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including white plastic seat cover with aluminium hinging device complete all as specified and directed.

S&F of syphonic action type PVC low level flushing cistern 10 ltrs capacity with 32mm dia flush pipe and fixing to supply pipe including PVC connection 600 mm long 15 mm bore with brass heads & washers and fixed complete all as specified and directed.

S&F in repairs syphonic action type PVC low level flushing cistern 10 ltrs capacity with 32mm dia flush pipe and fixing to supply pipe including PVC connection 600 mm long 15 mm bore with brass heads & washers and fixed complete all as specified and directed.

S&F of PVC connections 15 mm dia and 600 mm long with PTMT nuts and fixed complete all as specified and directed.

S&F of tubular towel rail brass chromium plated 20 mm dia D type 60 cm long between flanges complete all as specified and directed.

S&F of rotational moulded polyethylene water storage tanks, 3 layers (cylindrical vertical with closed top) of capacity 500 litres, hoisted including all fittings as required and 20 mm dia PTMT float valve (Min wt 20mm-210gms) and fixed in position complete all as specified and directed.

S&F of rotational moulded polyethylene water storage tanks, 3 layers (cylindrical vertical with closed top) of capacity 1000 litres, hoisted including all fittings as required and 20 mm dia PTMT float valve (Min wt 20mm-210gms) and fixed in position complete all as specified and directed.

S&F of vitreous china urinal, full stall type, white (excluding flushing cistern) but including CP waste fitting, PVC waste pipe and CP urinal spreader complete all as specified and directed.

S&F of vitreous china wash basins (flat back or angle back type) of size 630 x 450 mm, white incl cutting for & pinning in ends of brackets or erecting stand, brackets, CP brass waste coupling, 15 mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nut including waste pipe of standard length complete all as specified and directed.

S&F in repairs vitreous china urinal, half stall type, white (excluding flushing cistern) but including CP waste fitting, PVC waste pipe and CP urinal spreader complete all as specified and directed.

S&F of 100 mm dia stainless steel grating doom with or without hole complete all as specified and directed.

S&F in repairs 125 mm dia stainless steel grating with or without hole complete all as specified and directed.

S&F in repairs 32 mm bore LDPE waste pipe for WHB/ sink of length not less than 1 m upto floor trap and fixed complete all as specified and directed.

S&F of chromium plated shower rose 125 mm size with or without swivel joints, with shower arms any size including fixing to steel pipe or union of 15 mm bore complete all as specified and directed.

S&F in repairs 15 mm bore wash basin mixer, centre hole for mixing hot & cold water, brass chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferulle and fixed complete all as specified and directed.

S&F in repairs for health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F of 15 mm bore bib taps, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferulle and fixed complete all as specified and directed.

S&F of 15 mm bore stop valves, cast copper alloy, chromium plated, fancy type with long shank and cup (concealed type) with capstan head, screwed down, screwed for iron pipe or union complete as specified and directed.

S&F of 15 mm bore angle/ stop valves, cast copper alloy, chromium plated, fancy type with long shank and cup with capstan head, screwed down, screwed for iron pipe or union complete as specified and directed.

S&F in replacement 20 mm GI tubing medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F of 15 mm GI tubing medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors (Concealed type) complete all as specified and directed.

S&F of 20 mm GI tubing medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors (Concealed type) complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc; and making good, cutting exc 20 cm girth complete all as specified and directed.

M&L for precast cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in landings, cover slabs, precast man hole covers etc; and set in CM 1:4 complete all as specified and directed.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in any type of soils complete all as specified and directed.

Excavation over areas n exc 1.5 m deep and getting out in any type of soils complete all as specified and directed.

Excavation in trenches n exc 1.5 m deep and n exc 1.5 m wide for foundation, manholes, pipes, cable, etc; and getting out in any type of soils complete all as specified and directed.

Returning, filling in any type of soil including spreading, levelling, watering and well ramming in layers n. exc 25 cm complete all as specified and directed.

Removing excavated material to a distance n exc 50 m and depositing where directed at a level n exc 1.5 mtr above starting point all as specified.

Removing excavated material to a distance exc. 500 m but n exc. 1.5 km and depositing where directed at a level n exc 1.5 mtr above starting point all as specified.

M&L for drilling holes for re-barring mild steel TMT bars 6 to 8 mm dia upto 80 mm depth in existing plinth beams using chemical Hilti HY 200 R or equivalent make as approved by GE complete all as specified and directed.

M&L for 150 mm bore reinforced concrete pipes, class NP-2, laid in trenches and jointed with collars in cement mortar 1:3 including demolition of existing pipe and concrete complete all as specified and directed.

M&L for cement concrete 1:4:8, type D-2 (uisng 40 mm graded stone aggregate) as concrete bed to 150 mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) floor trap plain with SS grating, fixed and jointed with solvent cement complete all as specified and direcetd.

S&F of 125/110 mm bore PVC (SWR) gully trap, set and jointing with solvent cement complete all as specified and directed.

S&F in replacement 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/floors complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/floors complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/floors complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bends of any radius and jointed with solvent cement complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bends of any radius and jointed with solvent cement complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal and jointed with solvent cement complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal and jointed with solvent cement complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) vent cowl and fixed complete all as specified and directed.

S&F of mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F of mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F of mild steel TMT bars 5 mm dia and over upto aand including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for preparation of old painted steel or iron surfaces of any description, exceeding 10cm width or girth and applying two coats of synthetic enamel paint of approved tint complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8, type B-1 (using 40mm graded stone aggregate) as in sub base concrete complete all as specified and directed.

M&L for providing of water proofing roof treatment to non accessible roof with APP modified membrane with non woven polyster reinforced of wt not less than 3 Kg/Sqm and thickness not less than 3 mm uniformely embedded during manufacturing process complete comprising of following activities:-

(a) Applying 10 mm thick plaster in CM 1:4 mixed with and including water proofing compound @ 3% by weight of cement applied over roof slab. After the plaster is cured the roof will be tested for water tightening by ponding with water for 72 Hrs for any seepage / leakages etc. and if any seepage is oberved the rectification will be carried out by pressure grouting under the pressure of 5 Kg/Sqcm using cement based cement grout. After the surface is repaired the slab will again be tested for water tightness against before processing further treatments.

(b) The surface of the roof, parapet and gutters, drain mouths etc. over which water proofing treatment is to be applied shall be cleaned of all foreign matters such as fungus, mass, dust etc. by wire brushing and dusting. For cast iron drain outlets the groove shall be cut around to tuck in the treatment as pipes, chimney stacs etc. and other similar situations to ease up about corners.

(c) Applying hot blown bitumen VG-10 as primer conforming to IS : 3384-1965 @ 0.30 Kg/Sqm on prepared surface till the surface is properly impregnated.

(d) All joints & changes in direction should be curved with cement morar 1:3 mixed with SBR latex @ 200 ml per bag of cement and cured well before laying the membrane.

(e) Fillet of PCC (1:2:4) type B-0 of 100 x 100 mm shall be provided at all junctions of vertical and horizontal surfaces and wherever there is a change of direction. The membrane should not be taken over at any steep turns and hence all corners /junctions should be rounded.

(f) Applying APP modified water proofing membrene as specified shall be laid by torch application method laid on hot bitumen 85/25 grade (bonding material) at the rate of 1.2 kg/sqm as per manufacturers instructions. The overlaps while torching shall be 100 mm in both directions (longititudinal and transverse directions). All overlap joints shall be sealed throughly by thermofusing both the membrene layers and sealing it with the help of hot trowel. The overlap joints shall be made as monolithic layer.

(g) Applying two coats of heat reflective bitumen-compatibe aluminium paint over membrane after cleaning.

S&F of LLDPE (Linear Low-Density Polyethylene) septic tank conventional designed for 25 Usres to carry sewage and sludge water not less than 3000 Ltrs capacity including necessary excavation in any type of soil, PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation bed, vent shaft and making connections complete all as specified and directed.

M&L for construction of soakage well of size 1.8 m dia x 3.00 m depth with and including necessary excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete type C-2 including intercepting chamber and screen chamber made of brick masonary in CM 1:4, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of suitable size complete all as specified and shown in drawing No. CEBZ/TD/78 revised upto date and as directed.

M&L for point wiring for one light / fan / bell point with multi-stranded copper conductor stranded copper conductor 1.5 Sqmm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable, 1100 volts grade in and including medium grade, PVC concealed conduit and conduit accessories of not less than 20 mm dia, concealed in wall/ floor etc, ISI marked with sheel metal mild steel flush box, white cover plate with frame for fixing modular switches, sockets and fan regulators etc. including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

All as per item No. 132 here-in-before but one 3 pin 5 Amp socket outlet on same board.

S&F of modular switch piano, one module, single pole, one way, 6 Amps, 240 volt, 50Hz, AC, ISI marked complete all as specified and as directed.

S&F of modular socket outlet, 2 module multipurpose having provision for 2/3 pin, 5/16 Amp, 230 volt AC complete all as specified and as directed.

S&F of ceiling rose surface bakelite, three terminals, 230 volt AC complete all as specified and as directed.

S&F of lamp holder, PVC/ polycarbonate body with back plate suitable for batten fittings with 9 Watt LED bulb complete all as specified and directed.

S&F of exhaust fan, rust proof steel body, 230 Volts AC, single phase of size 300m sweep with blades, frame and louvers and all necessary fittings with and including drilling of hole and repair of disturbed surfaces complete all as specified and directed.

S&F of building security light fitting 35 Watt, made up of pressure die cast aluminium housing with high efficient LED as lighting source and pc over having top opening separate driver compartment with IP-66 protection and impact resistance of IK-07 including suitable galvanized iron light grade pipe brackets of 1 mtr length, bent to shape to obtain required shape including clamps, nuts, bolts, washers etc; and making connection with suitable copper wire of size 23/0.0076 complete all as specified and directed.

S&F of sheet metal enclosure for SPN DB (single pole and neutral) single door type, surface mounted, concealed in wall, 4 ways, 240 Volts, IP 43, ISI marked with 200 Amps rated bus bar, dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed. Note:- MCB shall be measured and paid separately.

S&F of MCB, SP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 6 to 32 Amps including making connection with suitable size aluminium / copper lugs complete all as specified and directed.

S&F of MCB, SPN, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 32 Amps including making connection with suitable size aluminium / copper lugs complete all as specified and directed.

M&L for sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core PVC insulated FRLS cable 1100 V unsheathed with stranded copper conductor of 4.0 sqmm nominal cross section area and drawing into rigid non metallic PVC conduit, ISI marked, medium grade inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples, lock outs, etc. of 20 mm external diameter and PVC insulated stranded copper conductor of 2.5 sqmm nominal cross section area as earth wire complete all as specified and directed. Note: Two runs of 4.0 sqmm cable, one run of 2.5 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length.

M&L for earthing complete with galvanised steel plate earth electrode 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to earthing lead of size 32x6 mm galvanised mild steel wire by means of bolts, nuts, check nuts and washers of galvanised iron from earth plate to test point upto 7.5 metre including all as shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete chamber in cement concrete M15 (Nominal Mix) using 20 mm nominal size coarse aggregate, precast RCC cover slab in cement concrete M15 (Nominal mix) using 20 mm nominal size coarse aggregate of size 40 x 40 x 5 cm reinforced with 8 mm dia TMT bars @ 150 mm c/c both ways with one handle for lifting made out of 8 mm dia bar, GI funnel, GI wire mesh filter, 20 mm dia GI pipe medium grade for watering, 40 mm dia GI pipe medium grade for protection of earthing lead, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil/ strata and testing complete all as specified and directed.

S&F of LED light fitting mirror type with high out put diffuser of 2 feet long, 10 watt, 220 Volts AC, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and laying 20 mm bore GI tubing medium grade (as per IS 1239) inclusive of all fittings laid in trenches with and including provision of tapping to main water pipeline complete all as specified and directed.

Supply and laying 25 mm bore GI tubing medium grade (as per IS 1239) inclusive of all fittings laid in trenches with and including provision of tapping to main water pipeline complete all as specified and directed.

S&F of Gun-metal gate valves of size 25 mm with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 16852.00

Please Enable Macros to View BoQ information