MLA_Fund 2025-26_Ettayapuram TP_ Auditorium

Amount

Earthwork excavation for foundation in all soils and sub soils in hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders and to full depth as may be directed,except in hard rock,requiring blasting including shoring and shuttering and bailing out of water wherever necessary,refilling the sides of foundation with excavated earth or sand in layer of not more than 15cm thick.well rammed and consolidated and depositing on bank with initial lead and lift of 10m & initial lift of 2m and depositing the surplusr earth within the compound in places shown by the departmental officers with iniital lead and lifts,clearing and levelling the site etc., complete as per SS20B and as directed by departmental Engineers(TNBP No.17,23,24).

Plain Cement Concrete 1:4:8 mix (One Part of Cement, Four part of Fine Aggregate and Eight part of Coarse Aggregate) Using 40mm ISS HBG metal for foundation and basement including dewatering if found necessary and laid in layer of not more than 15cm thick and consolidated including all cost conveyance of materials and labour charges etc. complete as per standard specifications and as directed by departmental Engineers(TNBP No.28).

Supplying and erecting centering for sides and soffits including supports and strutting uptp 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90cmx60cm and 10 gauge stiffened, welded with mild steel angles of size 25mmx25x3mm for boarding laid over silver oak (country wood) joist of size 10cmx6.5cm dia spaced about 90cm centre to centre and supported by casuarina props of 10cm to 13cm dia spaced at 75cm centre tocentre etc.complete complying with standard specification and as directed by the departmental engineers. TNBP No.30

A) For Beam, Lintel Roof Slab

B)Square column

C) Grade Beam

Supplying, fabricating and placing in position mild steel or TMT rods for all reinforced cement concrete works as per design given including cost of steel and binding wire with all conveyance and lead charges in all floors etc.complete complying with standard specifications and as directed by the deparmental engineers. TNBP No:30

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers -

Supplying and Filing in foundation and basement with Filling well Gravel in layers of not more than 15cm thick well rammed,watered consolidated including cost and conveyance of materials and labour charges etc., complete as per Standard Specification and as directed by departmental Engineers(TNBP No.24&25).

Brick work in following Cement Mortar using best quality of Fly Ash Brick of size 230x110x70mm for foundation and basement including curing, etc., complete complying with standard specifiction.

Random Rubble Masonry using CM 1:5 (One part of cement & five parts of sand) mix using rough stones and bond stones for foundation and basement and including pointing above G.L including cost and conveyance of materials to work site and including all labour charges for mixing, laying, curing the concrete etc., complete as per standard specifications and as directed by departmental Engineers.TNBP No:35H

Plastering with cement mortar 1:5(One Cement and Five Sand) 12 mm thick complying with water proof compounded with standard specification.

Finishing the exposed surface of RCC item of work such as slabs, beams, sun-shades, acia, eanopyslab, stair-case, waist slab, handing slab etc., with cement mortar 1:3 (one cement and three sand) 10MM thick including raking the surface. The rate is to include the cost of providing cement mortar or nosing for sun-shades and stair ease steps, landing slabs and etc., complete complying with standard specifications.

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Painting two coats with ready mixed Emulsion of first class quality paint and of approved color over a priming coat, including through scrapping, clean removal of dirt, etc., complete.

Wiring with 2x1.5sqmm (22 / 0.3) PVC insulated SC unsheathed Cu. Conductor of 1100v grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T switch and making good of the concealed portion with suitable colour for PVC concealed light point. SD 24 ISI Make with Standard specification .

Supply and run of 2 of 4 sqmm (56 / 0.3) insulated SC unsheathed Cu.Cconductor of 1100V grade on 7/20 GI bearer wire for service connection mains. SD 66 ISI make with standard specification.

Supply and run of 2 x 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in 25mm dia GI Pipe ( Class ‘B’) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 71 ISI make with standard specification.

Supply and fixing of single box type 4’40 w fluorescent fitting LED complete with copper choke and condenser with TW Round on wall and with tube with PVC unsheathed leads from tennauble to the nitting SD 88 ISI make with standard specification.

Wiring with 2x1.5sqmm (22 / 0.3) PVC insulated SC unscheathed Cu.conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3mm thick Hylem sheet cover for 5 A 3 pin non inter locking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. SD 38ISI make with standard specification

Finishing with top of roof with one course of machine pressed tiles of size 20cmx20cmx20cm of approved quality laid in cement mortar 1:3 (One cement and three sand) 12mm thick mixed with water proofing compound conforming to ISS by 2% weight of cement used and the joint pointed neatly to full depth of tiles with same water proofing compound mixed with cement motar ,red oxide, etc.complete complying with standard specification as directed by the departmental officers. TNBP No:44-I

Laying with first quality design ceramic tiles of all colours new ceramic tiles 305 x 305x 6mm tk for flooring and set in Cement Mortar 1:3 (one part of cement & three parts of sand)20mm thick and pointed with white cement including adding with suitable colouring pigments of match with the colour of tiles used and curing etc., complete.including cost and conveyance of all materials etc.and all labour charges etc.complete as per Standard specification and as directed by the departmental officers. TNBP No.special

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm Dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm Dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm center with 2 Nos. of 25mm Dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Arun Krishna Prasath (BID ID -1418508)

T SHANTHI (BID ID -1418506)