Renovation of gate and gearing system of cross and Head Regulators at R 110468 Fatehabad Branch, H.R of New Samaini Minor at RD 129000/L Fatehabd Branch and Cross Regulator at RD 157000 Sidhmukh Nohar Feeder

Amount

Replacement, Supply & Fabrication of Old Gate as per sizes complete in all respect of size 5922L/2850H mm or size 3502/3572L/3450H mm as per design and specification approved

Fabrication, Supply, Erection & Commissioning of M.S. Columns, Staircase and Platform including chequard plate complete in all respect.

Supply, Fabrication & replacement of channnel and girder ot make it Suitably heavy for winch machine arrangment complete in all respect.

Replacement of Chequard plate 8mm as per exisiting sizes

Supply & Insttallation of 30 KVA Generator set comp. In all respect.

Replacement of J – Type Musical Rubber seal 100 x 12 x 44 with G.I. Nuts and Bolts complete in all respect.

Replacement of Flat Type Bottom Rubber Seal 80 x 12 with G.I. Nuts and Bolts complete in all respect.

Replacement of Wheel Assembly set as per existing sizes complete in all respect.

Provinding rope drum hoist having 16 ton capacity complete in all respect

Provinding rope drum hoist having 8 ton capacity complete in all respect

Replacement of Old Hoist with new winch machine hoist having 1/1.5 ton capacity complete in all respect

Replacement of old gate as per existing sizes with heavy structure and Girders complete in all respect having size 1956x1400mm or 2658x1400mm as per design and specification

Replacement of old gate as per existing sizes with heavy structure and Girders complete in all respect having size 2700x1350mm or 1800x1000mm or 2550x1350mm as per approved design and specification

Electrification & Modification of Gates to operate Electrically with electric motor 5 H.P. (960 RPM) with extended shaft, Horizontal foot mounted in due on motors, continuously

Installation of Gates and Hoisting System with the help of hydraulic movable crane complete in all respect.

Dismantling of Old Gate and Structure winch machine with the help of hydraulic movable crane complete in all respect of size 5775x2850 mm or size 2650x3450mm .

Dismantling of Old Gate and Structure winch machine with the help of hydraulic movable crane complete in all respect of sizes 1956x1400 mm, 2658x1400mm, 1454x2700mm, 1158X1800mm & 1354X2550mm .

Dismantling of Old winch screw machine double spindle type with the help of hydraulic movable crane complete in all respect.

Alignment, Oiling and Greasing of Gates and Gearing Arrangement complete in all respect.

Scrapping, Cleaning and Painting of Gates & complete structure arrangement with CA-50 Black Epoxy & Smoke Grey Paint complete in all respect.

Replacement of Single Spindle Hoist as per existing sizes complete in all respect.

Modification & Renovation of existing embedded parts 270 x 275 x2.56mtr (avg.ht.) complete in all respect.

Providing and laying in position machine batches and machine mixed design mix cement concrete M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. All works upto plinth level (Note :- Cement content considered in this item is@ 330 kg/cum. Less cement used as per design mix is recoverable. However no extra payment shall be made if excess cement is used as per design mix). Unit 6.25.1 All works up to plinth level

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D or more. As per new HSR 2021 item no.6.33.6

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete. As per new HSR 2021 item no.6.30.1.

Demolishing brick work manually/by techanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar.As per new HSR 2021 item no.5.7.4.

All works up to Plinth Level. M-15 grade plain cement concrete. (cement content considered @ 240 kg/cum).As per new HSR 2021 item no.6.22.2.2

Pointing on brick work or brick flooring with cement mortar 1 :3 (1 cement : 3 fine sand): Raised and cut pointing.As per new HSR 2021 item no.11.25.2.

Brick masonry 1:3 in foundation & plinth. (-) brick bats

Recovery of steel scraps

Recovery of brick bats (HSR item No. B0146)

TEJWANT RAI GOVT CONTRACTOR