SPECIAL REPAIR OF BLDG NO 46 and 49 AT SOMNATH ENCLAVE AND PROVN OF TOILET BLOCK NEAR OR LINE IN STATION HQ UNDER GARRISON ENGINEER AMRITSAR CANTT

Amount

15 ID/SRW/BLDG/(ASR)- 02/2023-24 Taking down cement plaster on brick or stone or concrete surfaces of wall etc ,icluding raking out joints , hacking for key, scrubbing down with water etc. ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for rendering 15mm thick on fair face of brick works or concrete surfaces of walls with CM (1:6) finished the surface for even and smooth without using extra cement ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for rendering 15mm thick on other than fair face of brick works or concrete surfaces of walls with CM (1:4) finished the surface for even and smooth with WPC @100 ml per 50 kg of cement or all as per manufacturing instruction ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for Rendering 5mm thick in CM 1:3 to fair face of brick works or concrete surfaces of ceiling finished the surface for even and smooth without using extra cement ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for preparation of new plastering surfaces of walls and applying two coat of cement base paint over a coat of primer etc. ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for two coat of oil bound distemper over a coat of primer on newly plastered surface of wall incl preparation of surface ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for Complete removal of existing treatment of old decorated surfaces of wall including stipping nails, holes, filling the cracks with putty and applying two coat of oil bound distemper etc. ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for Three coats of white washing on new plastered surfaces of ceiling , chajjas after preparation of surfaces ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for one coat of white wash including preparation of old decorated surface of ceiling ; Complete all as specified and directed by Engineer-in-Charge

Demolition of Brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles ; Complete all as specified and directed by Engineer-in-Charge

Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) as in boundary wall, drain etc ; Complete all as specified and directed by Engineer-in-Charge

All as per Item No here-in-before, but except bricks. Note:- Serviceable bricks obtained from dismantling of brick work shall be reused.

Material and Labour for Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM (1:4) as in boundary wall, drain etc ; Complete all as specified and directed by Engineer-in-Charge

Demolition of Reinfoced cement concrete for roofs, floors,(other than ground floors) beams , stair cases, landing,chajjaa and similar suspended work ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for RCC with type B0 (1:2:4) (using 12.50mm graded aggregate ) in Slabs supported on walls , beams and columns in floors , roofs ., landings, balconies , canopies, deck slabs and cover slab in shelves and the like ; Complete all as specified and directed by Engineer-in-Charge

Formwork to the soffits of suspended slabs such as roof slabs , floor slabs , landings and similar work ; not exceeding 200 mm thick ( Horizontal or sloping ) and making flat rough finished surfaces of concrete ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for TMT bars 6 to 8 mm mm dia and over , cut to length , bent to shape required , including cranking , bending spirally for hooping ends and binding with and including mild steel wire ( annealed ) not less than 0.9 mm dia or securing with clips ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing 15 mm Bib taps, cast copper alloy fancy type chromium plated with capstan head screwed down screwed for iron pipe of 15mm bore and fixed in repairs ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs for 15mm dia Stop valves, , high pressure, with crutch or butterfly handle, chromium plated, fancy type, screwed both ends for iron pipe or for unions ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs 15mm bore stop valve fancy type chromium plated with long shank and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs 20 mm gun metal globe or gate valve with iron wheel head, screwed both end for iron pipe ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs for Vitreous China wash basin with Pedastal, white, flat back, size 500 X 400mm, excluding taps, waste, chain and plug and porcelain stopper but including padestal, complete as in repairs ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs for brass chromium plated shower rose 125 mm size with swivel joint including fixing to 15mm dia steel pipe or union ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs for 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete as in repairs ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing for vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe)including connection to trap, and to flushing pipe, anti-syphonage pipe etccomplete including making good to floors with PCC bedding (1:5:10) type E2 using 40mm nominal brick ballast and connection to trap with cement mortar all as specified, and making good to floor including demilition of PCC / Lime concrete bedding existing pan ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixingin repairs PVC waste pipe 32/38/40 mm dia, 600 to 750 mm long comlete all as specified and directed ; Complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs stainless steel plate rack of size 1m x 1m, with folded edge gloss finish fixed to wall ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs PVC connections 15mm size with PTMT nuts of length 450mm ; Complete all as specified and directed by Engineer-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable rubbish off the premises ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with cement @ 3.0 Kg/Sqm ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for 15mm thick Screed bed or beading layer of cement mortar (1:6) for laying floor finishes ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for 10mm thick Screed bed or beading layer of cement mortar (1:4) for vertical surfaces like dado, skirting etc. ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for Non-skid Ceramic colour tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ; Complete all as specified and directed by Engineer-in-Charge

All as per item No -36 but as in skirting ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour for Glazed ceramic colour tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour 20mm thick Granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick Screed in CM (1:6) ; Complete all as specified and directed by Engineer-in-Charge

Re-fixing for 15 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors etc) including cleaning, re-running the old screw threads etc ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs 15mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors , wall etc ( surface or concealed type) including taking down ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs 20 mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors , wall etc ( surface or concealed type) including taking down ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing for 500 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with manhole cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection including dismantling / taking down old PVC water tank, ball valve etc complete all as specified in SSR Part-I ; Complete all as specified and directed by Engineer-in-Charge

Taking down chowkats with shutters (without taking down of shutter from the frames) exc 1.50 Sqm and n.exc 4.00 Sqm each ; Complete all as specified and directed by Engineer-in-Charge

Taking down chowkats with shutters (without taking down of shutter from the frames)n. exc 1.50 Sqm each ; Complete all as specified and directed by Engineer-in-Charge

Taking down shutter of any description exc 1.00 Sqm and n.exc 2 Sqm each ; Complete all as specified and directed by Engineer-in-Charge

Refixing Shutter of any description exc 1 sqm but n exc 2 sqm each ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either toside and as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in M.S frame welded/sealed to stiles and rails with suitable PVC sheet beading and jointed together with solvent cement. Supplying and fixing in the frame at site as specified of drawing.

Supply and Fixing framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete FE -290 Gde E-165 ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing 25 mm thick flush shutter, soild core construction, with block board core and plywood face panel commercial type on both sides ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing 35 mm thick 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass/gangue (with sash bars) edges of forming plain chamfered or rounded fitted with cut and mitred bead for securing glass/ gauged etc size of member of shutter as per Pt-I, Section 8, Clause 8.20 (a) ; Complete all as specified and directed by Engineer-in-Charge

Taking down steel window / ventilator of any description & size n exc 1.50 sqm area ; Complete all as specified and directed by Engineer-in-Charge

Material and Labour box type steel window, ERW hollow P-Section size 60 mm x 25 mm, double rebated ERW section of 1.25mm thick, comprising of glazed skelton & gauzed shutter of ERW tube P-Section size 50mm x 20mm with one or two No openable leaf for each shutter consisting of two Nos Sashbar of T-section 20 x 3 mm welded to frame with one No verticle mullion of ERW box type T Section of size 60mm x 25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixture like as Handle, Tower Bolt, Stopper, Cleat, Pintal hinges, holdfast and guard bars etc as given below all as shown on drg No CEJZ/TD-06/07 incuding cutting holes and PCC 1:2:4, type B-1 in hold fast block, ; Complete all as specified and directed by Engineer-in-Charge as follows:- (a) Hold fast 150mm long of MS flat 12mm x 3mm - 4 Nos per Window (b) Handle of Z section 20mm x 25mm, 100mm long- 01 No per leaf (c) MS tower bolt 150mm long - 02 Nos per leaf (d) Z Section stopper 20mm x 25mm, 100mm long - 01 No per leaf (e) Cleat 55mm long of hollow square 15mm, 0.63mm thick- 01 Nos per leaf (f) MS pintol hinges size 75mmx12mm - 2 Nos per leaf (g) MS guard bar 10mm square bars @ 10cm c/c fixed horizontly Note:- Sheet glass, wire mesh and painting shall be measured and paid sperately.

Supply and Fixing in repairs box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as stopper, cleat, pintal hinges, hold fast etc all as shown on drg No CEJZ/TD-06/07 dt 07.06.07 incuding cutting holes ; Complete all as specified and directed by Engineer-in-Charge. Note: Sheet glass and painting shall be measured and paid Separately.

Supply and Fixing framed work such as grill, framed guard bar and similer work conforming to FE 290, GDE E- 165 ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire staples in window and door as in new door/window ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples / wooden beads in wooden / steel window and door as in repairs ; Complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden & steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads exc 1.5 Sqm ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 3mm thick sheet glass in repairs , ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane including hacking out old broken glass ( any thickness, size , quality or description ) from wooden frames glazed with putty or fixed with beads ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 4.0mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane in any position ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing butt hinges 100mm size medium weight cold rolled mild steel, fixed with screws or welded to steel frame ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 150 mm aluminum , anodised, barrel tower bolts of extruded section ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 150 mm aluminum Handle Cast type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 250mm aluminum alloy, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing M.S. 300mm ordinary rat tail rod pattern spring including roller and roller plate complete including necessary welding to door frame ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new wood surface over 10 cm girth or width and apply two coat synthetic enamel paint over a coat of pink primer ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new steel surface and applying two coat of synthetic enamel paint over one coat of red oxide primer on new surface ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of old painted steel surfaces of any description, over 10cm in width or girth, not otherwise described for One coat of synthetic enamel paint ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for One coat of synthetic enamel paint after preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing for flat iron as in hold fast,including tarring or coal tar black paint conforming to Fe 410-0 or Fe 310-0 ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour PCC (1:2:4 ) type B1( using 20 mm graded aggregate ) Used as in Brick or concrete wall for fixing of holdfast ; Complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in ground floors and pavings (unreinforced) n.exc 15 cm thickness (below or above ground level) ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in 50 mm thick plinths protection and as in path ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing, in 25mm dia MS pipe PVC sheathed, decorative fancy type, curtain rod including brackets & a set of ABS finials ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs110 mm bore PVC (SWR ) pipes single socketed, in any lenth with rubber ring fixed to wall ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC (SWR) bend 110 mm size ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 110 mm bore PVC (SWR) single Tee ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for cup board shutter, frame made of angle iron 35x35x6mm, covered with 1.00mm thick MS sheet, welded to frame including suitable handle, lugs and locking arrangement ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC sheet 5mm thick, in backside of kitchen cabinets for support ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC board 18mm thick, in cupboard shelves and backside (for hanging) kitchen cabinet etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing solid PVC shutter 18mm thick with one side prelam of any shade plain colour as in cup board, kitchen cabinet shutter etc. ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 40mm long box type steel hinges spring action type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 75-80mm long stainless steel handle ; Complete all as specified and directed by Engineer-in-Charge.

Dismantling brick tiles or terracing tile, single/double layer on roof including mud phuska any thickness and leepng plaster, seggregating, cleaning and stacking servicable tiles for reuse ; Complete all as specified and directed by Engineer-in-Charge.

Demoliton of mud in roof any thickness including mud plastering and removing to distance exc 250m but n exc 500m ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for 40mm thick brick tiles, laid on and including 15 mm thick cement mortar 1:6 and joints grouted and pointed flush in CM 1:3 mixed with 5% crude oil by weight of cement ; Complete all as specified and directed by Engineer-in-Charge.

All as per Srl Item No. 87 here-in-before but except brick tiles. Note:-Old serviceable tiles shall be reused.

Material and Labour for PCC (1:3:6) type C-0 (using 12.5mm graded stone aggregate) averaging 50 mm thick as in roof padding mixed with WPC @ 100ml per 50 Kg cement finishing the surface even and smooth without using extra cement ; Complete all as specified and directed by Engineer-in-Charge. . Note : WPC shall be measured and paid separately under relevant item of Sch 'A').

Material and Labour for 15mm thick plaster in CM (1:3) on RCC roof surfaces as in vertical surfaces mixed with water proofing liquid compound finished the surface even and smooth without using extra cement ; Complete all as specified and directed by Engineer-in-Charge. (Note : WPC shall be mixed @ 100 ml / 50 Kg bag of cement or as recommended by manufacturer and the same shall be measured and paid seperately.

Material and Labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces etc ; Complete all as specified and directed by Engineer-in-Charge.

Material & Labour for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( Wt not less than 150 gms /sqm ) laid on bituminous surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Supply only water proofing compound liquid type (ISI Marked) ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Removing of nails, making good holes, cracks, etc and applying 1 mm thick wall care puty on walls including finished the surface even and smooth ; Complete all as specified and directed by Engineer-in-Charge.

Excavating in post holes in soft/loose soil each not exc. 0.50 cum and getting out , returining filling and ramming earth or broken rubble mixed in layer not exc 25 cm ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour PCC (1:3:6) type C-2 using 40 mm graded aggregate as in foudation Filiing Etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing rolled mild steel sections ( angles, tees etc ) as in post fixed with angle cleats, MS plate etc including necessary welding etc ; Complete all as specified and directed by Engineer-in-Charge. ( Fe-410 w gde E-250)

Supply and Fixing MS work ( MS angle ) as in roof truss (framed), purlins, rafters including distance pieces, cleats etc including necessary cutting, welding etc ; Complete all as specified and directed by Engineer-in-Charge. Fe-410 w gde E-250 quallity A.

Supply and Fixing for pre-painted galvalume aluiminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws ; Complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre deep for foundation, manholes,sewage line etc exc 10 sqm on plan and getting out in soft/loose soil ; Complete all as specified and directed by Engineer-in-Charge.

Returning,filling in,spreading,levelling,watering and well ramming in layers not exc 25cm thick each ; Complete all as specified and directed by Engineer-in-Charge.

Removing excavated material to a distance exc 250mtr but n.exc 500 mtr and depositing where directed at a level not exc 1.50 metre above the starting point ; Complete all as specified and directed by Engineer-in-Charge.

Demolition and breaking up existing unserviceable 150 mm bore SGSW pipe and haunching against the sides of pipe at any depth including removing rubbish to a distance exceeding 100m ; Complete all as specified and directed by Engineer-in-Charge.

Supply,laying in trenches, jointing and testing 150 mm bore salt glazed stoneware pipe grade 'A' drain pipe ISI marked ; Complete all as specified and directed by Engineer-in-Charge..( Excavation and earthwork shall be measured and paid for separately under appropriate items of Sch. 'A'.)

Material and labour for PCC 1:4:8 type D-2(using 40mm graded crushed stone aggregates)for bed of sewage lines of 150 mm bore including packing under and haunching against the sides of pipe after they are laid and tested ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 1.00 mm thick back sheet in steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for Sand filling under floors or in foundations including watering and consolidation ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade ; Complete all as specified and directed by Engineer-in-Charge.

AC/REV/20/2023-24 Material and Labour for surface dressing n exc 15 cm deep soft/loose soil ; Complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft soil ; Complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm ; Complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n.exc 50 m and depositing where ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Cement concrete type D2, 1:4:8 (40 mm graded aggregate) in foundations, filling and mass concrete ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for RCC (Nominal Mix) type B1, 1:2:4 (20mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for RCC (Nominal Mix) type B1, 1:2:4 (20mm graded aggregate) in column, pillars, piers, post and struts ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for RCC (Nominal Mix) type B1, 1:2:4(20 mm graded aggregate) as in Beams, canatilivers, bressummers, lintels over 1.5m span etc ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for RCC (Nominal Mix) type B1, 1:2:4 (20mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of rough finished surfaces of concrete in foundation and plinth beams; and similar work; vertical or to batter ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Formwork to sides of pillars, posts, struts, piers, columns and stanchions of rough finished surfaces of concrete ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) of fair finished surfaces of concrete ; Complete all as specified and directed by Engineer-in-Charge.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for TMT Mild steel bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips ; Complete all as specified and directed by Engineer-in-Charge.

All as per item No 123 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for broken bricks Hardcore of gauge n exc. 63 mm, deposited , spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for 75mm thick Cement concrete type D2, 1:4:8 using 40mm graded agregate as in sub base of floor ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for brick work with sub class 'B' bricks straight curved on plan exc 6 mean radius built in CM 1:6 ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Rendering 15 mm thick on fair/unfair faces of brick work or concrete surfaces in CM 1:6 and to be finished even and smooth ( without using extra lime or cement) ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Rendering 15 mm thick on fair/unfair faces of brick work or concrete surfaces in CM 1:4 and to be finished even and smooth ( without using extra lime or cement) ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:3 as on ceiling and to be finished even and smooth ( without using extra lime or cement); Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing pressed steel frames 1.25mm thick for door size of frame125 X 60mm with double rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) and for filling of hold fast and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges and two coats of synthetic enamel paint to outer surface with red oxide primer after prepration of surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for box type steel window, ERW hollow P-Section size 60mm x 25 mm, double rebated ERW section of 1.25mm thick, comprising of glazed skelton & gauzed shutter of ERW tube P-Section size 50mm x 20mm with one No openable leaf for each shutter consisting of two Nos Sashbar of T-section 20 x 3 mm welded to frame with one No verticle mullion of ERW box type T Section of size 60mm x 25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixture like as Handle, Tower Bolt, Stopper, Cleat, Pintal hinges, holdfast and guard bars etc as given below all as shown on drg No CEJZ/TD-06/07 incuding cutting holes and PCC 1:2:4, type B-1 in hold fast block complete all as specified and directed as follows:- (a) Hold fast 150mm long of MS flat 12mm x 3mm - 4 Nos per Window (b) Handle of Z section 20mm x 25mm, 100mm long- 01 No per leaf (c) MS tower bolt 150mm long - 02 Nos per leaf (d) Z Section stopper 20mm x 25mm, 100mm long - 01 No per leaf (e) Cleat 55mm long of hollow square 15mm, 0.63mm thick- 01 Nos per leaf (f) MS pintol hinges size 75mmx12mm - 2 Nos per leaf (g) MS guard bar 10mm square bars @ 10cm c/c fixed horizontly Note:- Sheet glass wire mesh and painting shall be measured and paid sperately.

Material and labour for box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD-06/07 dt 07.06.07 incuding cutting holes and making good ; Complete all as specified and directed by Engineer-in-Charge. Note:- Sheet glass and painting shall be measured and paid separately.

Supply and Fixing of Rolled mild steel in framed work (Fe 410W Gde-E-250, Quality A) as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Flush shutters in existing chowkhats, solid core construction , with block board core and plywood face panels, commercial type on both sides ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Galvanised mild steel wire cloth, 0.63 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 100mm longe Butt Hinges, medium weight, cold rolled mild steel and fixed ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 150mm long aluminium, anodised, barrel tower bolts of extruded section and fixed ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Aluminium handles, 150mm size cast type anodised ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 200mm Aluminium alloy. Anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour preparation of newly plastered surface of wall and applying two coats cement base paint over a coat of primer to match the existing treatment ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new plastered surfaces and applying two coats of oil bound distemper on walls ; Complete all as specified and directed by Engineer-in-Charge.

All as per item No 142 above but on ceiling surface ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new wooden surface over 10cm width or girth and applying 2 coats of synthetic enamel paint (ordinary tint) over a coat of pink primer ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new steel or iron surface over 10cm width or girth, not otherwise desribed and applying 2 coats of synthetic enamel paint (ordinary tint) over a coat of red oxide, zinc chrome primer ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour Cement concrete 75 mm thick type C-2 (1:3:6) using 40 mm graded stone aggregate as in plinth protection etc finished even and smooth using extra cement ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing (SWR) pipes of 110mm dia single socketed, in any length with rubber ring joints, laid in trnches or in floors ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Factory made single extructed WPC but frame size 65x 125 mm (wood polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum,screw withdrawel strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2,modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Factory made single extructed WPC (wood polymer Composite) solid Plain flush door shutters of 35 mm thick comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minumum dencity of 650 kg/ cum and screw withdrawa strenth of 1800 N (Face )&900 N (Edge), minimum compressive strength of 50 N/mm2,modules of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/moisture proof and fire retardant and fixed with steelness steel butt hinges of requred size with necessary full body threank SS screw all as direction of engr in charge ( steelness srew and butt hinges and necessary SS Screw shall be paid separatly) ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing bib taps cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm dia fixed in repairs ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 20mm dia fixed in repairs ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing plastic water closet seat coloured closed pattern with flat bottom cover and mild steel chromium plated or aluminized hinging device ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing for 15mm bore stop valves, cast copper alloy, concealed type, chromium plated with long shank and cup ,screwed down,handles, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge.

Supply and fixing vitreous china squatting pan ( Orissa Pattern) size 580 x 440 mm (white), with PVC P or S trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 including taking down/dismantling old unserviceable WC ; Complete all as specified and directed by Engineer-in-Charge.. Note :- Flush pipe and flushing cistern to be measured and paid separately.

Supply and fixing in replacement pillar tap long body 15mm dia cast copper alloy with capstan head chromium plated fancy type, screwed down high pressure, with or without letters ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe; Complete all as specified and directed by Engineer-in-Charge.

Supply & fixing vitreous china wash down water closet pan (padestal pattern) white with flush pipe for low level flushing cistern including plastic water closet seat white with jet, closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device fixed in repairs ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing white PVC valve less syphonic action type low level flushing cistern of 10 ltrs capacity with inlet ball valve, float valve, push button type handle including pipe 32mm dia of PVC(Heavy duty) flush pipe including brackets and taking down/dismantling old unserviceable cistern ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fix viterous chinaware wash hand basin light colour/white of size 550x 400cm flat back or angle stay, brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets,32mm bore PVC waste pipe of appropriate length ilcluding taking out of old WHB & making necessary connections ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing glazed ceramic coloured tiles 450x300mmx6mm thick, etc. on vertical surfaces such as skirting , dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Coloured/printed non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 15 mm thick screed bed or bedding layers in CM 1:6. ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC(SWR)single socketed in any length with rubber ring joint fixed with wall of 75mm ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Supply and Fixing PVC (SWR) pipes 110mm dia bend any radius ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 110mm bore PVC (SWR) branch piece , single, equal fitted with oval access doors ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing rotational moulded polythene, triple layers, water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in position including Supply and Fixing 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs CP brass towel rail of 20mm dia and 600mm long ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs 125mm CP shower rose fancy type with CP arm ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing galvanized iron steel tubing medium grade 20 mm bore with all fittings and fixed Complete all as specified to walls, ceiling or laid in floor ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing galvanized iron steel tubing medium grade 15mm bore with all fittings and fixed Complete all as specified to walls, ceiling or laid in floor ; Complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre deep for foundation, manholes,sewage line etc exc 10 sqm on plan and getting out in soft/loose soil ; Complete all as specified and directed by Engineer-in-Charge.

Returning,filling in,spreading,levelling,watering and well ramming in layers not exc 25cm thick each in soft/loose soil,; Complete all as specified and directed by Engineer-in-Charge.

Removing excavated material to a distance exc 250mtr b anut n.exc 500 mtr and depositing where directed at a level not exc 1.50 metre above the starting point ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for brick work with sub-class 'B' bricks straight or curved on plan exceeding 6 metres mean radius built in cement mortar 1:4 including flush bricks straight or curved on plan exceeding 6 metres pointing as the work proceeds(Except internal surfaces of manholes and other surfaces where plaster is to be done) ; Complete all as specified and directed by Engineer-in-Charge.

Supply,laying in trenches, jointing and testing 150 mm bore salt glazed stoneware pipe grade 'A' drainpipe ISI marked all as specified & directed.( Excavation and earthwork shall be measured and paid for separately under appropriate items of Sch. 'A'.) ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for PCC 1:4:8 type D-2(using 40mm graded crushed stone aggregates)for bed of sewage lines of 150 mm dia including packing under and haunching against the sides of pipe after they are laid and tested ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for PCC 1:4:8 type D-2(using 40mm graded crushed stone aggregates) as in foundation and mass concrete incl nessary form work if required for drain bed / foundation of manholes etc ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for PCC 1:2:4 type B-0(using 12.5mm graded crushed stone aggregates) as in benching for manholes, bands, coping, bed plate etc including necessary form work, if any and finishing exposed surface even and smooth using extra cement ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with modular metal flush boxes of suitable size & modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly all as directedNOTE: Cost of modular metal flush boxes with a coat of synthetic enamel paint over a coat of red oxide to steel surface to avoid rust, concealed in wall with suitable white cover plate for mounting switch/sockets, regulator, bell push etc and Cost of cutting chases & making good to distrubed surface with cement mortar, if required any shall be deemed to be included in the quoted rate (a) One light point/Fan point controlled by one switch

Material and labour for Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with modular metal flush boxes of suitable size & modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly all as directedNOTE: Cost of modular metal flush boxes with a coat of synthetic enamel paint over a coat of red oxide to steel surface to avoid rust, concealed in wall with suitable white cover plate for mounting switch/sockets, regulator, bell push etc and Cost of cutting chases & making good to distrubed surface with cement mortar, if required any shall be deemed to be included in the quoted rate (a) One 5 Amps outlet point on same board with other switches/sockets

Material and labour for Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with modular metal flush boxes of suitable size & modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly all as directedNOTE: Cost of modular metal flush boxes with a coat of synthetic enamel paint over a coat of red oxide to steel surface to avoid rust, concealed in wall with suitable white cover plate for mounting switch/sockets, regulator, bell push etc and Cost of cutting chases & making good to distrubed surface with cement mortar, if required any shall be deemed to be included in the quoted rate (a) One 3 pin 5 Amps socket outlet on independent board.

All as per ser item No 183 here in above but point wiring with 2.5 Sqmm FRLS cable and 4.0 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing modular switch 1 way 6A, 240 volts, 1 module ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing modular switch 1 way 16A, 240 volts, 1 module ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing modular socket, 6A, 240 volts, 3 pin combined 2 module, ISI marked flush type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing modular socket, 6A/16A, 240 volts, 2/3 pin combined 2 module flush type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65x50 mm three terminal ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Lamp holder angular type, PVC/Polycarbonate type with back plate suitable for batten fittings ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 8way, 240 volts grade with 200 Amps insulated rated bus bar, earth bar IP- 43 & IK-09, door earthing flush to wall, including testing suitable for fixing MCB SPN, SP etc, including taking down existing unserviceable one and removing from site ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing MCB of SP 5 to 32 Amps current carrying capacity, 240V, 10KA 'C' curve, ISI marked, fixed in the MCB DB complete conforming to IS/IEC-60898-1 2002 with connection testing and commissioning including taking down old unsv one from the site ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing MCB of SPN 32 Amps current carrying capacity, 240V, 10KA 'C' curve, ISI marked, fixed in the MCB DB complete conforming to IS/IEC-60898-1 2002 with connection testing and commissioning including taking down old unsv one from the site ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sub main wiring with 2 runs of 4.0 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, suitable size with conduit fittings and accessories concealed in wall/ceiling/floor including 1 run of 4.0 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly incl taking down old unsv one from site; Complete all as specified and directed by Engineer-in-Charge. NOTE: Two runs of 4.0 sqmm copper cable and one run of 4.0 sqmm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length

Supply and Fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, double sided connection, holder including LED tube light connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose, including taking down existing unserviceable one and removing from site ; Complete all as specified and directed by Engineer-in-Charge

Supply and Fixing LED street light 35 Watt, 230 V AC outdoor type with epoxy black powder coated sheet, high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket of suitable size with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting complete and testing, including taking down existing unsv one and removing from site ; Complete all as specified and directed by Engineer-in-Charge

Supply and fixing fresh air fan 250mm size including making of hole/opening in wall ; Complete all as specified and directed by Engineer-in-Charge

Munish Kalia

m/s. gopal krishan

S S CONSTRUCTION COMPANY

GEE EMM ASSOCIATES

Sai Construction Co.

Mahajan Builder

Hindustan Industrial Equipment Co.