Construction of pre-fabricated structure at western sector gate and at old PRO office etc. inside BARC, Trombay, Mumbai

Amount

From 0.00 to 1.50 m depth from Average Ground Level

From 1.50 to 3.00 m depth from Average Ground Level

From 0.00 to 1.50 m depth from Average Ground Level

From 1.50 to 3.00 m depth from Average Ground Level

Lead charges of soil for 1st 1 KM or part thereof, by mechanical transport including loading unloading, stacking / levelling etc. Note: Deductions for voids shall be made from truck measurements for soil, @ 20% from corresponding stack/truck measurement.

Providing and laying in position cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm)/ M-10 with minimum cement content 220 Kg/CuM including consolidation, finishing, curing etc. complete as per specifications and drawings but excluding the cost of Formwork shuttering, centering Complete at all levels.

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm)/ M-15 with minimum cement content 320 Kg/CuM including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels

Providing and laying in position Reinforced Cement Concrete of Grade M-30 using 20mm maximum size aggregates and crushed sand of approved quality including weigh batching, mechanical mixing, transporting , placing, vibrating, including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, consolidation,finishing, curing etc.complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications.

up to Plinth Level (Substructure)

Extra for RCC/PCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants . Note: (1) In view of limit on water-cement ratio for durability requirements, concrete admixtures shall be used after taking prior approval of Engineer-in-Charge and the rates quoted for these items shall be inclusive of the cost of admixtures, trial mixes, testing (at site & at approved labs), etc. complete. (2)All projections, fins etc. in the concrete surface formed at the joints in the formwork should be ground & flush and finished at no extra cost. (3)The minimum cement content for item nos. 4, 5 & 6.1 is given in the table below:

Providing, centering, shuttering Form work using PVC Film faced plywood to get a neat form finish surface for all types of structures including necessary strutting, proping, staging, supports etc and deshuttering the same after the specified time all as per drawings and specifications at all levels.

For Sub Structure Note: Abrupt changes in surface of concrete, mortars fins etc. at formwork joints shall be evened out by chipping, grinding and finishing with cement mortar curing etc. as directed by Project Engineer all at his own cost

Providing Reinforcement Steel of grade Fe 500D for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings. Steel supplied by the contractor Using TMT bars of specified grades of all sizes. TMT bars to be supplied by the contractor from the own plants of approved make and manufacturers only using virgin materials confirming to IS:1786 Note : 1. The contractor shall supply documentary evidence of purchase of steel, Test certificate from approved manufacturers and also testing third party from approved laboratories with out any extra cost. 2. Binding wire required for the work will have to be supplied by the contractor at their own cost and will not be measured for payment. 3. Cover blocks shall be of same grade of concrete.

Providing Structural steel work using angles, channels, joists and other sections, welded and / or bolted in built up sections for trusses, structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Engineer-in-charge.

Up to and including 300 mm Joists, 350 mm channels, and below sections using materials produced by approved make and manufacturers. All test reports to be provided along with the supply of the materials confirming to IS:2062

Providing Structural steel work in M.S Plain Plates and chequrred Plates for Embedded Parts, Trench Covers, Connection plates etc.including cutting, hoisting, fixing in position and applying a priming coat of approved zinc chromate steel primer etc.including cost of structural steel Plates, welding all labour charges etc. complete as per drawings and specifications. Using materials produced by the own plants of approved make and manufacturers only using virgin materials. All test reports to be provided along with the supply of the materials confirming to IS:2062

Providing, supplying, cutting, welding, fabricating, hoisting and fixing in position structural steel members like trusses, purlins, posts etc. using MS hollow / circular / square / rectangular tubular sections including appling a coat of Zinc chromate primer of approved make all as per specifications, drawings and as directed by the Engineer in charge

Supplying, fabricating and delivering and fixing at site MS anchor bolts as shown in drawing or as directed by Engineer-in-charge, including nuts/lock nuts, anchor bolt assemblies etc. complete.

Providing and constructing Random Rubble masonry using spotless black trap or approved local stone in foundation and plinth in C.M 1:6 (using 100% Manufactured Sand) including raking out joints or simultaneous flush pointing below ground level / plinth level, including levelling the masonry with cement concrete 1:6:12, curing etc. complete as per drawings and specifications.

Providing and fixing 75 mm thick Non Asbestos Fiber Reinforced Aerated Cement Sandwich wall panels of minimum bulk density of 876 kg/cum of approved manufacturers , made out of Light Weight Fiber Reinforced Aerated Cement Concrete Core Composed of Portland Cement, Fly Ash Binders Etc. and 4 to 5 mm thick Non Asbestos Fiber Cement Boards on either Side of the Core having a Tongue and Groove on Longitudinal side of the Modules . These panel Modules are Erected / Installed using Galvanised Iron Steel Tracks of suitable section as per manufacturers specification at bottom and Top of the Wall respectively Including all Necessary Material Required for Erecting and Fixing the Wall Panel Complete as per the Direction of the Engineer in Charge. For Permanent and Exterior Joints the Paste of Sodium Silicate and Fly Ash / Cement to be Applied at Tongue and Groove Interlocking Joints and on Exposed Joints with Acrylic Putty and Fiber Tape on Both Side all as per design, drawing and specification and as directed by Engineer-in-Charge. (Structural steel used for support if any required shall be paid in relevant item) Note: Necessary cut-outs for Doors & Windows shall be made in the wall paneling. The rate shall be inclusive of all materials & Labour required for making cut-outs and additional GI channel frame work. No deductions will be made for the cut-outs for measurement purpose.

Providing and constructing Brickwork in cement mortar 1:6 using crushed sand with Flyash / Flyash Lime bricks with minimum 70 kg / Sq. cm strength of approved make and size in Sub structure including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings.

Providing and constructing Brickwork in cement mortar 1:4 using crushed sand with Flyash / Flyash Lime bricks with minimum 70 kg / Sq. cm strength of approved make and size in Sub structure including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings.

Providing and constructing Half brick masonry using Flyash/ Flyash Lime bricks in substructure with minimum 70 kg / Sq.cm strength of approved make and size in partition walls in C.M 1:4 using crushed sand including scaffolding, raking out joints, curing etc. complete and with stiffners of RCC 1:2:4 (105 X 75 mm size) at every 900 mm height including form work curing etc. complete as per specifications but excluding reinforcement. (Reinforcement will be paid under relevant item)

Providing 15 mm thick Internal plaster in cement mortar 1:4 without cement punning (using Crushed Sand) finished smooth, including sieving of sand to required fineness, preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete.

Providing Raised and cut pointing on stone with cement mortar 1:3 using crushed sand as per specifications and as directed at site by the Engineer-in-charge.

Providing 20 mm thick External plastering in two coats under layer 12 mm thick with C.M 1:4 (using crushed sand) finished with a top layer 8 mm thick in C. M 1:3 (using crushed sand) including approved water proofing compound @ 2% by weight of cement or as per manufacturer's specifications, sieving of sand to required fineness, scaffolding up to 10 meters height, finishing, curing etc. complete as per specifications and as directed by the Engineer-in-charge

Providing and fixing Glazed VITRIFIED Tiles in flooring and skirting of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge.

Extra for polymer mortar in place of cement mortar for skirting using Glazed VITRIFIED Tiles in Item no. 22

Supplying, stacking and laying of 230 mm thick rubble soling stones as under floor base including packing with smaller stone and compacting, ramming including spreading and consolidation of blinding material, moorum etc. complete all as per specifications and as directed by the Engineer-in-charge

Labour charges for murum filling under floors of specified thick in layers of not exceeding 150 mm thickness including consolidation etc. complete (using murrum available at site)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS 15622 of approved make. shade and colour of size ranging from 300 - 600 mm long and 300 mm - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor tiles of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm conforming to IS 15622 of approved make in all colours and shades as approved by Engineer-in-charge over a bed of 20 mm thick bed of cement mortar 1:4 (using crushed sand) and jointing with grey cement slurry including pointing with white cement based Tile grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P brass / stainless screws all complete as per drawings and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealant etc. (fittings glazing and paneling shall be paid for separately)

Anodized Aluminium sections (Minimum anodizing thickness of 15 micron)

Extra for colour anodizing

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc. with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

With clear float glass panes of 6.00 mm thickness

Providing and fixing in position suspended false ceiling using G.I. exposed ceiling suspension system of grid size 600mm x 600mm with main runner 38mm x 24mm, Cross Tee 27mm x 24mm and wall angle 22mm x 24mm. Using 4mm thick ( High pressure steam cured), pre-painted, self-embossed, reinforced designer cement boards (Ivory) of Lake and Hill/Oceanic/Cascade/Electra texture, conforming to IS 14862:2000 Type B Category III, to be placed in a grid of G.I. system duly suspended with 3m dia G.I./M.S bar hanger fixed with steel dash fasteners or iron Purlins from the roof with adjustment clip. The main runners to be secured to structural soffit by hanger @ 1200mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1200mm Cross Tee to be interlocked between main runners @ 600 c/c so as to form 600mm x 600mm or grid. Provide provisions for light fixtures, air conditioning ducts and diffusers, fire alarms, sprinklers or smoke detectors etc. as per the drawing and directions of engineer in charge.

Providing and fixing FRP door shutters flush door / paneled type with plain colour or wooden veneer finish of approved make, design & colour. made out of 1.5 mm thick FRP skin moulded over wooden frame work of 40 mm wide and required thickness wooden styles and minimum 100 mm wide lock rails and wooden blocks for door stoppers, tower bolts, baby latch, aldrop, handles etc. wherever required and core filled with Polyurethane Foam and fixing with 4 Nos 100 mm (ISI marked) stainless steel hinges with S.S. wood screws aluminium Bow handles, 2 Nos of Aluminium 75 mm Baby latch complete all as directed at by the Project Engineer. 35 mm thick paneled door type of approved colours including the cost of 100 mm ISI marked heavy quality stainless steel butt hinges with necessary screws.

Providing and fixing anodised aluminium aldrops ISI marked of size 300 X 16 mm transparent or dyed to required colour or shade with necessary screws etc. complete as directed by the Engineer-in-charge

Providing and fixing anodised aluminium tower bolts of size 300 X 12 mm (barrel type) ISI marked of approved make transparent or dyed to requried colour or shade with necessary screws etc. all as per specifications and as per drawings.

Providing and fixing aluminium handles 175 mm long Inner grip 125 mm with 12 mm dia rod plate type BOW handles ISI marked of approved make, anodised transparent or dyed to req. colour or shade with necessary screws etc. complete.

Providing, painting, finishing walls with two coats of anti-algae, weather proof acrylic smooth emulsion paint of approved make with silicon additives on sand face plaster/ plain plaster & concrete surfaces of required shade over new work over a base coat of exterior cement primer including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge.

Providing and applying wall painting two coats on new work with premium plastic emulsion paint of approved brand to give an even shade, including a coat of approved cement primer, including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and Painting two coats of synthetic enamel paint on steel surfaces of approved brand and manufacture to give an even shade over a primer coat. Including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Supplying, fabricating, testing, transporting, handling and erecting at required positions and levels metal roofing and canopy roofing including flashings and insulation etc. as per approved drawings and design complete as directed by the Engineer-in-charge including all consumables comprising of the following: Double skin insulated standing seam roofing system comprising of 0.50 mm thick colour coated / bare Al-Zinc Alloy coated steel 0.50 mm with overall width of 400 to 500mm by seaming for 100% water tightness on outer face and 0.50 mm thick inner linear sheet with galvalume sheet profile and physical material properties as specified. These sheets shall be fixed on specially reinforced polyamide or acetylate anti friction di electric brackets at every location for permitting unhindered, free sheet movement at all required locations. The profile shall have a special in built drainage joint at side laps to make it fully watertight even in fully submerged condition. It shall have overall depth of 100 mm from horizontal after fixing . The side laps shall be of interlocking type without requirement of any mechanical seamer. Insulation: This shall be comprising of two layers of Rockwool insulation each of 50 mm thick with density of 48 kg / Cu. M. Sub Grit (Top Hat) 1.5 mm thick Glavanised steel hat section fixed to main purlins, above first layer of insulation, to support the aluminium sheets. Inner linear sheet of 0.50 mm nominal TCT of physical material properties as specified. Vapour Control layer : The vapour control layer to reduce the movement of water vapour from inside the building through the roof construction to reduce the risk of condensation shall consists of 3 layer membrane to be laid continuous across its surface shall be fully sealed at laps, perimeters, penetrations to ensure effectiveness & aluminium foil of 0.50mm thick laid over insulation board.

Providing and fixing precoated Galvalume roofing accessories using self drilling / self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete.

Roofing accessories of galvalume sheet above 600mm total width up to 1200 mm for ridges, gutters, aprons and flashings

Providing, laying , jointing, fixing and testing heavy quality ( (ISI Marked C-Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples, reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydraulic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing Teflon tape, chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint, all as directed by the Engineer-in-charge. Pipes with ISI marked 'C' -Class heavy quality pipes of approved make.

15 mm dia G.I pipe

20 mm dia G.I pipe

25 mm dia G.I pipe

32 mm dia G.I pipe

40 mm dia G.I pipe

50 mm dia G.I pipe

Providing & fixing in position heavy pattern screw down gun metal gate valve with handles and wheels of approved make including testing for 10 Kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-charge

Providing and fixing C.P brass bib cock of heavy quality of specified / approved make as per specifications and as directed by the Engineer-in-charge

15 mm dia bib cock of approved type and make

20 mm dia C.P brass bib cock of approved type and make

Providing and fixing C.P Brass open stop cock of Heavy Quality of specified / approved make as per specifications and as directed by the Engineer-in-charge

15 mm n.b CP Brass open stop cock of approved make and type

20 mm n.b CP Brass open stop cock of approved make and type

Providing and fixing C.P brass Angle cock of heavy quality of specified / approved make, for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-charge

15 mm n.b CP brass Angle cock of approved make

Providing and Fixing 15 mm CP brass Angle stop cock of approved make- quarter Turn

Providing and Fixing CP brass 100 mm dia shower rose with Shower arm of specified make as per specifications and as directed by Engineer-in-charge complete

Providing and fixing 15 mm C.P brass 2 in 1 bib cock and Angle cock combination of Heavy Quality of approved make as per specifications and as directed by the Engineer-in-charge

Providing and fixing C.P brass 2 way Angle cock (2 Angle cock combination in single fitting) of heavy quality of approved make as per specifications and as directed by the Engineer-in-charge.

Providing and fixing 15 mm C.P brass pillar cock of heavy Quality of approved make and specified type as per specifications and as directed by the Engineer-in-charge.

Providing and laying non pressure NP2 class RCC Hume pipes of approved make, with collars jointed with stiff mixture of cement mortar in the proportion of 1:2, laying to the levels, slopes and as per the drawings and specifications and as directed by the Engineer-in-charge including testing of joints etc. complete.

150 mm Dia RCC Hume pipe class Np2

Providing and constrctioning Inspection chambers of Internal size clear dimension of 900 x 600 mm in 230 thick brick masonry with cement mortar 1:4 over a bed of 150 mm thick 1:4:8 cement concrete foundation, plastering with cement mortar 1:4 20 mm thick on inside, out side and all exposed surfaces finished with a floating coat of neat cement, brick corbelling at top to provide opening of 900 X 450 mm, embedding the frame and cover with CC 1:2:4 concrete, and fixing cast iron steps if necessary at 300 mm intervals complete . Depth of chamber not exceeding 900 mm. (excavation, soling, cast iron cover and C.I steps will be paid separately under relevant item)

Extra depth over initial depth of 900 mm for chambers of 900 x 600 mm internal size. Including fixing cast iron steps (C.I steps shall be paid under relevant item)

Providing, supplying, fixing in position, under floors or in walls centrifugally cast iron pipes including required specials like bends, tees, 'Y' collars, cowl etc. for soil, waste and ventilation pipes conforming to IS.3989 of approved make including cost of jointing with spun yarn and molten lead of specified quantity, caulking the joints, including testing of pipes, painting with primer, fixing at walls with necessary approved type of clamps and brackets complete all as per drawings and specifications and as directed at site.

75 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 0.90 kg lead / joint

100 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 1.00 kg lead / joint

Providing and fixing cast iron nahani trap / floor trap of 100 mm inlet and 75 mm outlet, (weighing 5.80 Kg each), jointing with lead with the connection pipes, placing as per the drawings, embedding in cement concrete 1:2: 4 and making circular hole up to floor level using 110 mm O/D PVC pipes of 6 Kg / sq.cm pressure and fixing 1 No 125 mm dia C. P brass grating , complete all as specifications and drawings and as directed by the Engineer-in-charge

Providing and fixing white vitreous china European type Water Closet with 'P' or 'S' Trap with solid seat and lid of approved make, 10 liter low level white PVC flushing cistern with manually controlled device (handle lever) conforming to IS:7231, flush bend, fixing EWC with C.P brass screws, 15 mm PVC heavy quality inlet connection of 450 mm long, including testing , commissioning & cleaning etc. complete all as per drawings and specifications and as directed by the Engineer-in-charge

E.W.C. pan ordinary colour range with ISI marked white solid plastic seat and lid.

Providing and fixing Indian water closet (Orissa pan) of apperoved make with 100 mm China ware P or S trap, One no. 10 litre High level or low level white PVC flushing cistern with flush pipe & bend with manually controlled device (handle lever) conforming to IS:7231, PVC 15 mm Inlet connection with all fittings and fixtures complete including all connection, embedding in position commissioning, cleaning etc. all as per drawings and specifications and as directed by the Engineer-in-charge.

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china flat back half stall urinal size 580 x 380 x350 mm / 610 mm Aquaseal model of approved make with approved make 32mm C.P flush value with standard flush pipe and C.P. brass spreaders, 32mm urinal waste coupling with dome grating and clamp etc. including making G.I water line connection complete as directed by the Engineer-in-charge (Only G.I. pipes will be paid under relevant Item)

Single half stall urinal with C.P brass Flush valve. Note : For fixing flush valve 32 mm G.I water line provision to be made which will be paid under relevant Item .

Providing and fixing vitreous China wash basin of approved make and colour with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32 mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge

White vitreous China wash basin size 630 x 450 mm and equivalent sizes with single 15 mm C.P. brass pillar tap

Providing and fixing 6 mm thick mirrors of size 600 x 450 mm of approved make with beveled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete all as per specifications and as directed by the Engineer-in-charge .

Providing and fixing stainless steel toilet paper holder recessed type of approved make and type with S.S screws as directed by the Engineer-in-charge complete.

Providing and fixing 150X150 mm soap dish of white vitreous Chinaware, of approved make including chasing walls making good the same after fixing the China Soap dish etc. complete all as per specifications and as directed by the Engineer-in-charge

Providing and fixing heavy quality C.P. brass waste coupling of following dia for wash basin and sink of approved make, size and quality all as directed complete

C.P Brass Waste coupling 32 mm Dia of approved make Half threaded or Full threaded as per requirement.

Providing and fixing heavy quality CP brass bottle trap 31 / 32 mm of approved make single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the center of the waste coupling 77 mm breadth with 25 mm minimum water seal, of approved make for wash basins / urinal etc. all as per specifications and directed by the Engineer in charge.

Providing and fixing C.P brass towel rail of approved make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in-charge.

Providing and fixing Brass 15 mm C.P presstomatic series auto shut urinal flush cock of approved make and quality

Providing, transporting, lowering & laying in position at site at required elevation on prepared foundation concrete beds ready made RCC Hume pipe septic tanks of internal diameter as below, approved manufactured , constructing access shafts over the Hume pipe of internal clear size 600 mm x 600mm in brick masonry with cement mortar 1:6 raised up to ground level, plastering of the access shafts with cement mortar (1:4), 20 mm thick on in- side, outside & all exposed surfaces, finished smooth including providing C.I.steps weighing not less than 3.5 kgs. at 300 mm c/c of the access shaft chamber, depth not exceeding 1000 mm etc. complete including the cost of 1 No. of 75 mm dia. C.I. vent pipe about 3 meter long embedded in a PCC bed 45 cm x 45 cm x 30 cm & projecting 2 m above ground level & terminating with a C.I. cowl at top and providing & fixing 150 mm dia. SWG tee as per drawing & specifications.

900 mm Internal dia

Providing & Fixing 304 Grade Stainless steel wire fabric mesh 30 Swg thick & 625 Holes per Sq. Inch for windows/ ventilators etc. beading will be paid seprately .complete all as directed by the Engineer In charge.

Providing and fixing square mouth S.W. gully trap complete with CI grating brick masonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design

150 x 100 mm size gully trap "P" type

Providing and fixing Minimum 15 mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut Granite of Telephone Black colour for kitchen platforms, vanitiy counters, Wash basin Counters, Door Frames, window sills, facias and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete as directed by the Engineer-in-charge at all levels

Supplying and fixing Cast Iron Man hole or Cast Iron Steps cover of approved make and weight as specified in the drawings and as directed by the Engineer in charge.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix cement plastered on both sides with cement mortar 1:3 finished with a floating coat of neat cement and making necessary channels for the drain etc. complete.

For pipes 100 to 230 mm diameter

Lead charges for lead Exceeding 2 KM but not exceeding 3 KM, by mechanical transport including loading, unloading, stacking / levelling etc.

Debris Beyond 2 Km but up to and including 3 km Note: The rate is applicable for NET Quantities arrived at after making deduction for voids @ 30% from corresponding TRUCK Measurement

Providing and Fixing column encasement which includes fixing of one layer of 9mm thick (High Pressure Steam Cured) Heavy Duty Fiber Cement Board confirming to IS 14862: 2000 Type A Category IV are screw fixed on MS Square Hollow Section frame of size 25 x 50 x 2mm or as specified with 38mm fully threaded self drilling self tapping countersunk fiber cement screws at 300mm c/c to form the MS grid maximum of 610 x 610mm. Finally the square and beveled edges of the board are to be jointed and finished so as to achieve flush seamless finish, which includes special jointing compound & joint tape as per the recommended practices of manufacturer's specifications and as directed by the Engineer-in-charge.

Supply and fixing of Fiber cement Board with accessories Note: Structural steel will be paid in relevant item.

Providing and Fixing Chajja which includes fixing of one layer of 12mm thick (High Pressure Steam Cured) Heavy Duty Fiber Cement Board confirming to IS 14862: 2000 Type A Category IV are screw fixed on MS Square Hollow Section frame of size 25 x 50 x 2mm or as specified with 38mm fully threaded self drilling self tapping countersunk fiber cement screws at 300mm c/c to form the MS grid maximum of size 610 x 610mm. Finally the square and beveled edges of the board are to be jointed and finished so as to achieve flush seamless finish, which includes special jointing compound & joint tape as per the recommended practices of manufacturer's specifications and as directed by the Engineer-in-charge.

Supply and fixing of Fiber cement Board with accessories

Providing and fixing heavy quality health faucet with 1.50 metres long flexible hose (hand shower) of approved make and quality with wall brackets and type as per specifications and as directed by the Engineer-in-charge

Providing, hoisting and installing at required elevation moulded HDPE cylindrical vertical water storage tanks of approved make and quality of 1000 litre capacity with suitable S. M. C cover at top including the cost of labour for making hole in the storage tank for inlet, outlet, scour and overflow, providing and fixing necessary G.I Nipples ranging from 15 mm to 50 mm n.b of average 150 mm length with double check nuts, washers etc. complete as directed by the Engineer-in-charge.

Providing and grouting the joints of rubble stone pitching with cement mortar 1:3 and pointing the surfaces as directed complete as directed by the Engineer-in-charge

Providing and fixing dry stone pitching 22.5 cm thick laid in required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete as directed by the Engineer-in-charge

Providing and Fixing 3 layer PP-R ( Poly proplylene Random co Polymer) Pipes (as per I.S 15801/2008) of specified Grade and size, U.V stabilised & anti- microbial fusion welded, having thermal stability for Hot & Cold water supply including all PP-R Plain & Brass Cp threaded PP-R fittings including chasing the walls , Concealing the Pipes with fixing arrangements. This includes testing of joints & pipe lines complete all as per specifications, drawings and as directed by the Project Engineer.

PP-R pipes PN-16 / SDR 7.4 - 16 mm O/D

PP-R pipes PN-16 / SDR 7.4 - 20 mm O/D

PP-R pipes PN-16 / SDR 7.4 - 25 mm O/D

Meena Enterprises