Upgradation of interiors with modular work station/partition along with electrical works, painting, false ceiling at CWC, RO, Hyderabad

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 kg/10 sqm)

Providing and fixing MS grills of required pattern in frames of windows etc. with MS flats, square or round bars etc. all complete. A) Fixed to openings/ wooden frames with rawl plugs, screws etc.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mmwide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mmshall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side ofthe panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick bot the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick plain PVC door shutters

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

125 mm size

100 mm size

Providing and fixing aluminium sliding door bolt ISI marked anodised ( anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with nuts and screws etc. complete a) 250x 16 mm

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32mm dia

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing brass stop cock of approved quality:20 mm nominal bore

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand Cast iron S&S as per IS: 1729.

Providing and fixing square mouth SW gully trap grade 'A' complete with C I grating, brick masonary chamber with water tight CI cover with frame of 300x300mm size (inside), the weight of cover not less than 4.50 kg and frame to be not less than 2.70kg as per standard design. (a) 100x100mm 'p'type With F.P.S. Bricks class designation 75

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 398

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc., 20 mm nominal outer dia .Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc., 25 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 32 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 50 mm nominal outer dia .Pipes.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, by mechinical / manual means ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:Pipes, cables etc, not exceeding 80 mm dia.

Providing and fixing G.I. Union in Existing GI/PVC pipe line including cutting and threa-ding the pipe and making long screws etc; complete (a) (25mm nominal bore)

Providing and fixing on wall face unplasticised- Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes a) 110 mm diameter

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 75 mm diameter

Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised- Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110 mm bend

Shoe ( Plain ) - 110 mm shoe

Providing and fixing unplasticised - PVC clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with MS screws of required length including cutting brick/ laterite work and fixing in cement mprtar 1:4 ( 1 cement: 4 coarse sand) and making good the wall etc. complete. a) 110 mm

Painting with synthetic enamel paint of approved brand and manufacture to give aneven shade. (a) Two or more coats on new work

Description

Provide and fix 70 mm thick internal partition comprising a powder coated aluminium framework of rectangular hollow/section members 2"X 1" forming a modular grid of nominal 600 mm × 600 mm centres, fixed to floor and roof with suitable anchorage. Fix 8 mm thick commercial plywood (Greenply / Archit / Merino or equivalent) on both faces, edges trimmed with aluminium L-section where indicated. Both faces to be laminated with 1.0 mm decorative laminate (as approved shade) fixed with contact adhesive and rolled to avoid air entrapment. Provide all necessary screws, rivets, mechanical fasteners, adhesive, sealants, edge profiles, touch-ups and make good complete. Include mineral wool infill of 25–50 mm thickness in cavities for acoustic performance unless otherwise specified. Excludes doors, glazed panels or electrical cutouts which shall be measured separately

Size : 1200 mm x 1200 mm x 600 mm x 1200 mm H (Four Seater)

Size : 1500 mm x 1200 mm x 600 mm x 1200 mm H (Three Seater)

Size : 1500 mm x 1500 mm x 600 mm x 1200 mm H ( Four Seater)

Size : 1500 mm x 1200 mm x 600 mm x 1200 mm H ( Two Seater)

TABLE with STORAGE UNIT Table Size : 1800 mm x 750 mm x 750 mm H Top & Legs - Fabricated out of 25 mm thick Pre-laminated particle board (Merino) duly edge banded with thick PVC beeding. Modesty Panel- Fabricated out of 18 mm thick Pre-laminated particle board (Merino) duly edge banded with thick PVC beeding. Storage Unit Size : 900 mm X 400 mm X 750 mm HT fabricated out of 18 mm & 9 mm thick prelaminated particle board (Merino) duly edge banded with wooden beeding with swing type door and provided with handle & lock.CPU TROLLY MS Powder Coated (Ebco Brand) and KEYBOARD TRAY Size : 600 mm x 300 mm Fabricated out of 18 mm thick prelaminated particle board (Merino) edge banded with PVC strip. (EBCO Slide)

KEYBOARD TRAY Size : 600 mm x 300 mm Fabricated out of 18 mm thick prelaminated particle board (Merino) edge banded with PVC strip. (EBCO Slide)

Description

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required : 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (25 MM)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

Description

Supply, Installation, Testing and Commissioning of Torpedo 400 mm fan 125 Watts chorded electric 400 mm blade length with 2100 RPM speed remote controlled fan BLDC motor type. (Orient / Crompton/Havells) (5 years warranty)

Supplying installing testing and comissioning of prewired Recess mounting 2’x 2’LED Luminaire of System Wattage 36W, Luminous flux (±10%) 3600 lm,Luminaire efficacy 125 lm/W,Correlated Color Temperature 5700K ±355K,Color Rendering Index ≥80, Maintenance of lumen output 50000 hrs. Operating Temperature Range -10C to 40C, Input Voltage 150 to 270V AC, Input Frequency 50 to 60 Hz, System Current in Amp. @240V AC 0.12A, Power Factor ≥ 0.95,THD (@240V AC) <10%, Ingress Protection IP20) built driver complete with all accessories for hanging the fixuters from the truss as required as per the instructions(Equivalent to model:BZRSQL 36L XE WH OD SD Bajaj) Note: the Led Fixuters are complete under warantty for 5 years.

Supplying installing testing and comissioning of amiciSmart Automatic Over/Under Voltage and Over Load Protection (Adjustable Setting) with Auto Re-Connect LED Display Standard Din-Rail Mounted Single Phase 220V, 63A (13.8kW) including the IP 66 Protection weather proff box and wiring per the instructions of the Engineer Incharge

Supplying installing testing and comissioning of AC SPD Single Phase 2 Pole 320V, Surge Protection Device AC SPD - Type 2 in the Exisitng DB as per the instructions of the Engineer Incharge

Total Amount (in Rs.)

Total Amount (in Rs.)

Total Amount (in Rs.)

Total Amount (in Rs.)

Items of works

All Items of Civil works based on DSR Civil 2023

Market Rate