REPAIR/MAINT OF WOODEN AND STEEL FURNITURE ARTICLES AT MCEME UNDER GE MCEME SECUNDERABAD

Amount

M&L to repairs Bed plywood top by replacing the following unserviceable parts with first class teakwood/ plywood OSTF.Rest all as per drawings and directed by Engr-in-charge.(DRG NO. FD-246/247/213)

Long leg.

Short leg.

Long rail.

Stiffener.

3.5 thick teak face plywood, including half round teakwood beading if broken, of both side of head rest complete.

3.5 thick teak face plywood, including half round teakwood beading if broken, of both side of foot rest complete.

Plywood 12mm thick(9 ply) BWR Gde of suitable size in single piece.

M&L to repair Table Peg by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde).Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-384/277/236)

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners . Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Bottom rail made out of first class teakwood.

S&F PVC shoe 15mm dia of approved quality.

M&L to repair Teapoy by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawings and directed by engr-in-charge. (DRG NO. FD-382/278/232/34)

Top made out of 18mm thick pre-laminated exterior grade MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners . Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Bottom rail made out of first class teakwood.

S&F PVC shoe 15mm dia of approved quality.

M&L to repair Table Center by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-134/235/ 274)

Top made out of 18mm thick pre-laminated exterior grade MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners . Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Bottom rail made out of first class teakwood.

S&F PVC shoe 15mm dia of approved quality.

M&L to repair Hat stand with mirror by replacing the following parts with approved ones. Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-362)

Plywood 3.5/4mm thick OSTF.

First class TW beading at all around of frame.

Mirror 5mm thick.

Brass peg 115-120mm long.

Aluminium nail hook 50mm long.

M&L to repair Table dining 6 person by replacing the following unserviceable parts with teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawings and directed by engr-in-charge. (DRG NO. FD-273/239/30(M)/FD/MAP-II/03/TP)

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

S&F PVC shoe 20mm dia of approved quality.

M&L to repair Table dining 8 person by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-273/239/30(M)/TP)

Top made out of 18/19mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

S&F PVC shoe 20mm dia of approved quality.

M&L to repair Table writing by replacing the following unserviceable parts with first class teakwood/prelaminated MDF board (exterior gde)/plywood BWR gde.Rest all as per drawings and directed.(DRG NO. FD-275/249/33(M))

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood complete.

All as per item no 8.02 but front rail complete.

All as per item no 8.02 but side rail complete.

All as per item no 8.02 but side stiffener complete.

All as per item no 8.02 but center stiffener complete.

All as per item no 8.01 but side of cabinet complete.

All as per item no 8.01 but bottom of cabinet complete.

All as per item no 8.01 but shutter of cabinet complete.

Back of cabinet made out of plywood 6mm thick BWR gde.

Shelf of cabinet made out of plywood 12 mm thick BWR gde complete.

Drawer complete excluding knob.

Front of drawer made out of 18mm thick prelaminated MDF board and 4mmx18mm teakwood beading complete excluding knob.

Bottom of drawer made out of plywood 6mm thick BWR Gde complete.

Side/back of drawer made out of 12 mm thick (9ply) plywood BWR Gde complete.

MS lock of suitable size with duplicate key complete.

S&F PVC shoe 15mm dia of approved quality.

M&L to repair Sofa set 5/4 seater by replacing the following unserviceable parts with first class teakwood.Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-281/373/ FD/MAP-II/02)

Side rail.

Batton seat/back.

Front rail of single seater.

Front rail of three seater.

Back rest rail top/side of single seater.

Back rest rail side of three seater.

Back rest rail top of three seater.

Removing old foam cushion with tapestry cloth and S&F new P.U.Foam cushion of size 530mmx560mmx100mm (40 density) duly covered with approved quality of tapestry cloth.Make of foam cushion:- sleepwell (Feather Foam) / Kurl-on (Komfort universe goldline plus) / Corfom (Premium Foam) . Note:- Cost of tapestry cloth shall be between Rs 250/- to Rs 300/- per mtr.

Removing worn out tapestry cloth from old cushion and replacing the same with new tapestry cloth of approved quality. Note:- cost of tapestry cloth shall be between Rs 250/- to Rs 300/- per mtr.

M&L to repairs Chair dining MAP by replacing the following unserviceable parts with first class teak wood/approved ones. Rest all as per drawing & as directed.(DRG NO. FD/MAP-II/05)

Front leg.

Rear leg.

Stiffener.

Back rest.

S&F PVC shoe 15mm dia of approved quality.

PVC Seat 4mm thick with 4x10mm thick RIBS moulded alongwith seat in single piece of approved quality. Make- AMKO/ BRITE

S&F teakwood stiffener of suitable size 20mmx20mm thick beneath PVC seat to support PVC seat. Rest all as directed by enge-in-charge.

Taking out carefully old existing Knob from side board, table dressing gents, table dressing ladies etc and S&F new decorative Knob 32mm dia of approved quality. Rest all as directed by Eng-in-charge.

Taking out carefully old existing handle from side board, table dressing gents, table dressing ladies etc and S&F new CP handle 100 mm long of approved quality. Rest all as directed by Eng-in-charge.

Taking out u/s Bearer from different type of furniture articles likes side board, table writing etc and S&F new Bearer of suitable size, made out of first class teakwood complete. Rest all as directed by Eng-in-charge.

M&L to repair Chair easy by replacing the following unserviceable parts with first class teakwood.Rest all as per drawing and as directed by engr-in-charge. (DRG NO. FD-229/201)

Frame front/back of seat

Frame side of seat.

Frame top/bottom of back.

Frame side of back.

S&F PVC shoe 15mm dia of approved quality.

M&L to repair Chair easy by replacing old plastic cane of seat and back with new cane of 2 to 2.5 mm width and 0.4mm thick of approved quality. Border of chair shall be caned with 4mm wide and 0.6mm thick cane.

M&L to repairs Chair dining by replacing the following unserviceable parts with first class teak wood/approved ones. Rest all as per drawing & as directed.(DRG NO. FD-1105/279/270/262/228/203)

Front leg.

Rear leg.

Stiffener.

Back rest.

S&F PVC shoe 15mm dia of approved quality.

M&L to repair Chair dining by replacing old plastic cane with new cane of 2 to 2.5 mm width and 0.4mm thick of approved quality. Border of chair shall be caned with 4mm wide and 0.6mm thick cane.

M&L to repair Chair writing by replacing the following unserviceable parts with first class teak wood. Rest all as per drawing & as directed by engr-in-charge.(DRG NO. FD-280/250)

Front leg.

Rear leg.

Stiffener.

Back rest.

S&F PVC shoe 15mm dia of approved quality.

M&L to repair Chair writing by replacing old plastic cane with new cane of 2 to 2.5 mm width and 0.4mm thick of approved quality. Border of chair shall be caned with 4mm wide and 0.6mm thick cane.

M & L for preparation of old wooden polished surface of Bed Hard (FD- 246/247/213) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table Peg (FD-384/277/236) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Teapoy (FD-382/278/232/34) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table Center (FD-134/235/274)by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table dining 6 pers (FD-273/239/30(M)/FD/MAP-II/03) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table dining 8 pers (FD-273/239/30(M)/FD/MAP-II/03) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Hat stand with mirror (FD-362) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table dressing gents with mirror (FD-230/31(M)) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table dressing ladies with mirror (FD-251/32(M)/378) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Side Board (FD-241/371) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table writing (FD-275/249/33(M)) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Sofa set 5 seater (FD-281/373/FD/MAP-II/02) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Sofa set 4 seater(FD-281/373/FD/MAP-II/02) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Book case wooden (FD-237) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till glossy finish is achieved complete all as specified and directed.

M&L for preparation of old wooden polished surface of Chair dining (FD/MAP-II/05) by rubbing down the old polish from the wooden surface with sand paper, removing pluck mark with wooden scraper cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, Fevicol, water and colour) and adding colour (Raw seina/Burnt Seina/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achieved, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till high gloss finish is achieved complete all as specified and directed.

M&L for preparation of old wooden polished surface of Chair dining (FD-279/270/262/228/203) by rubbing down the old polish from the wooden surface with sand paper, removing pluck mark with wooden scraper cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, Fevicol, water and colour) and adding colour (Raw seina/Burnt Seina/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achieved, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till high gloss finish is achieved complete all as specified and directed.

M&L for preparation of old wooden polished surface of Chair Easy (FD-229/201) by rubbing down the old polish from the wooden surface with sand paper, removing pluck mark with wooden scraper, cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, Fevicol, water and colour) and adding colour (Raw seina/Burnt Seina/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achieved, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till high gloss finish is achieved complete all as specified and directed.

M&L for preparation of old wooden polished surface of Chair Writing (FD-280/250) by rubbing down the old polish from the wooden surface with sand paper, removing pluck mark with wooden scraper, cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, Fevicol, water and colour) and adding colour (Raw seina/Burnt Seina/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achieved, wiping off the polish from other than wooden surfaces with polish thinner and applying french polish till high gloss finish is achieved complete all as specified and directed.

Preparation of old painted iron & steel surface of Chair writing Map (FD/E6/MAP/12) by scraping & rubbing down with sand paper, removing dents and scratches, if any filing the same with paste filler and applying a coat of synthetic enamel paint (Ist grade quality) by brush or by spray machine complete all as specified and directed.

Preparation of old painted iron & steel surface of Chair computer MAP/chair revolving by scraping & rubbing down with sand paper, removing dents and scratches, if any filing the same with paste filler and applying a coat of synthetic enamel paint (Ist grade quality) by brush or by spray machine complete all as specified and directed. (Drg No.FD/E6/MAP/01,TP)

Preparation of old painted iron and steel surface (externally & internally complete) of Almirah large steel/Almirah steel 1/2H 1/2shelf FD-1031/67(M)/FD/E6/MAP/18 by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed.

Preparation of old painted iron and steel surface (externally & internally complete) of Almirah medium steel FD-1032/243/67(M) by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed.

Preparation of old painted iron and steel surface of Table 900x600x760 mm with drawer FD-1008 by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed.Note - Wooden portion of table 900x600x760mm shall be french polished with high gloss finish.

M&L for preparation of old steel surface of Chair verandah and welding loose joints, if any including de-rusting the surface and painting with one coat of synthetic enamelled paint white colour (1st Grade Quality) and recaning with 4-5 mm half round 0.6 thick plastic cane made out of virgin plastic, in existing pattern complete.Rest all as specified and directed by engr-in-charge. ( Drg No. FD-359/256/19 )

S&F PVC shoe suitable for chair verandah of approved quality.

M&L to repair Chair Writing steel by replacing unserviceable parts with approved ones. Rest all as directed by engr-in-charg (Drg No.FD-360)

Rexine cloth of seat and back complete.

P.U. Foam cushion 75mm (40D) of seat complete.

P.U. Foam cushion 50mm (40D) of back complete.

Arm made out of 1st class teak wood.

Preparation of old surface of chair writing steel by de-rusting the surface and painting with one coat of synthetic enamel paint (Ist quality) black colour complete. Wooden portion of chair shall be french polished with high gloss finish.Rest all as specified and directed. Not:- Note:- cost of Rexine cloth shall be between Rs 300/- to Rs 350/- per mtr.

M&L to repair Chair Writing MAP (made out of tapestry cloth) by replacing unserviceable parts as per drawing. Rest all as directed by engr-in-charg (Drg No.FD/E6/MAP/12) Note:- sample and shade of materials will be determined as per actual requirement at site.Cost of tapestry cloth shall not be less than 150/-per meter.

Only tapestry cloth of seat and back complete.

Tapestry cloth and foam of seat/ back complete.

Only Plywood of seat /back.

PU handle of suitable size and approved quality.

M&L repairs to Chair computer/chair revolving (made out of tapestry cloth) by replacing unserviceable parts as per drawings/TP. Rest all as directed by engr-in-charge. Note:- sample and shade of materials will be determined as per actual requirement at site.cost of tapestry cloth shall not be less than 150/-per meter.

Only tapestry cloth of seat and back complete.

Tapestry cloth and foam of seat/ back complete.

Only Plywood of seat /back.

Hydraulic of suitable size.

Base nylon of suitable size and pattern.

Wheel of suitable size and pattern.

Arm as required by size and design.

Dry cleaning of chair computer/ chair revolving med/ high back complete by soda, sampoo, castic, urea, chemical etc to clear dust.Rest all as directed by Engr-in-charge. (TP)

Dry cleaning of auditorium chair complete by soda , urea, chemical etc to clear dust.Rest all as directed by Engr-in-charge. (TP)

M&L to repair auditorium chair by replacing old PU foam of arm with new PU foam . Rest all as directed by Engr-in-charge. (TP)

M&L to repair Almirah steel large/Almirah steel 1/2H 1/2shelf by replacing the following unserviceable parts with approved ones.Rest all as per the drawings and directed by Engr-in-charge. (DRG NO. FD-1031/ 67(M))/FD/E6/MAP/18) Note:- Pattern and shape of lock and handle will be determined as per actual requirement at site.

MS lock 6 lever with duplicate key.

Chromium plated handle 130mm long.

Leg made out of 1mm thick MS sheet duly painted with one coat of red oxide primer.

Pane glass 3.5/ 4mm thick of almirah glazed large steel.

M&L to repair Almirah medium/small steel by replacing the following unserviceable parts with approved ones.Rest all as per the drawings and directed by Engr-in-charge.(DRG NO. FD-1032/243/67M)) Note:- Pattern and shape of lock and handle will be determined as per actual requirement at site.

MS lock 6 lever with duplicate key.

Chromium plated handle 130mm long.

Leg made out of 1mm thick MS sheet duly painted with one coat of red oxide primer

Pane glass 3.5/ 4mm thick of almirah small glazed steel.

M&L to repairTable 900mmx600mm with drawer by replacing the following parts with approved ones as mentioned below and as per drawing and directed by Enginner-in-charge(Drg No. FD - 1008)

MS lock of suitable size with duplicate key.

PVC handle of approved quality suitable for drawer.

Making the drawer functional by removing dents from MS sheet align and leveling the drawer and greasing it grooves so as to achieve smooth sliding complete.

Top made out of 18mm thick pre-laminated MDF board (exterior gde) one side classic walnut face and balancing white on other side duly teakwood beading 4x18mm all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

S&F PVC/hard rubber toe of approved quality and suitable size.

M&L to repair Desk executive by replacing the following parts with approved ones as mentioned below and directed by Engineer-in-Charge

Top of size 1375mmx510mm made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side lassic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

All as per item no 50.01 but shelf of size 1240mmx400mm complete including verticle portion.

All as per item no 50.01 but front of size 1290x400mm complete.

Rectangular PVC cover of suitable size

Nylon buffer of sitable size.

Preparation of old surface of desk by de-rusting the surface and painting with one coat of synthetic enamel paint (Ist quality) dark brown colour complete.Rest all as specified and directed.

M&L to repair Teapoy verandah by replacing the top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of lacquer polish. Rest all as per the drawings and directed by Engr-in-charge. (DRG NO. FD-255 /208/ 35 )

Preparation of old surface of teapoy verandah by de-rusting the surface and painting with one coat of synthetic enamel paint (Ist quality) white colour complete. Rest all as specified and directed by Engr-in-charge. (DRG NO.FD-255 /208/ 35)

S&F PVC/ rubber toe for teapoy verandah of approved quality and suitable size.

Repair to Billiard Table 12ft x 6ft (TP) (Spl item)

M&L to repair Billiard Table 12ft x 6ft by removing old unseviceable/ torn cloth of billiard table and supply and fixing new cloth of suitable size and make: 6811 west of England 32ozs of approved shade along with alignment checking and also net railing leather adjustments complete.Rest all as specified and directed.

Replacement of old billiard ball set of above said Billiard table with new ball set of make:ARAMITH 1G Ball set of approved quality.Total no of balls 22 nos.

Replacement of old short rest with cue of above said Billiard table with new short rest ( made out of brass) with cue (made out of ashwood) of apporoved quality.

Replacement of old short spider with cue of above said Billiard table with new short spider ( made out of brass) with cue (made out of ashwood) of apporoved quality..

Replacement of old long rest with cue of above said Billiard table with new long rest ( made out of brass) with cue (made out of ashwood) of apporoved quality..

Replacement of old long spider with cue of above said Billiard table with new long spider ( made out of brass) with cue (made out of ashwood) of apporoved quality.

Replacement of old long cue of above said Billiard table with new cue( made out ashwood) of apporoved quality.

Replacement of old cue stick of above said Billiard table with new cue stick (made out ashwood) of apporoved quality.

Removing of U/S Plywood from Charpoy GI Pipe Plywood Top (FD-220) and S&F new Plywood 12mm thick ( 9 ply) of BWR Grade ISI Maked of Size 1990x915mm with Nut & Bolt as required. Make of Plywood shall be Archidply (Silvi)/Duro (Duromac)/Centuryply (Sainik)/Greenply(Ecotec) BWR Gde . Rest all as specified and directed by Engr-in-Charge.

Welding of loose joint of flat Iron of charpoy GI pipe plywood top.

Tightening of complete frame & welding loose joint of GI pipe with frame of charpoy GI pipe plywood top.

M&L for preparation of old surface of flat iron (02 Nos) and painting the same with one coat of synthetic enamelled paint black colour (Ist grade quality) complete.

sandhya enterprises

Anjana corporation