Construction of Milk collection Centre Matho(Under Capex)

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30cm in depth, 1.5m in width as well as 10sqm on plan) including getting out and disposal of excavated earth lead upto 50m and lift upto1.5m, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) in foundation trenches or drains (not exceeding 1.5m in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift upto1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Dumping stone including cost of stones. in Horizontal on level

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C.work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for a) Foundations, footings, bases of columns, etc. for mass concrete

b) Lintels, beams, plinth beams, girders, bressumers and cantilevers

c) Suspended floors, roofs, landings, balconies and access platform

d) Columns, Pillars, Piers, Abutments, Posts and Struts

e) Edges of slabs and breaks in floors and walls Under 20 cm wide

Filling availableexcavatedearth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm indepth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement :6 coarse sand: 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete4.10.3 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with holdfast lugs or with dash fasteners of required dia & length (holdfast lugs or dash fastener shall be paid for separately). Second class Kail wood

Providing and fixing ISI marked flush door shutters conforming to IS:2202 (PartI) non-decorative type, core of block board construction with frameof 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35mm

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windowscomprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profilesduly reinforced with 1.60 ± 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes andsilicon sealant shall be paid separately). Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made. For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth& width of profile shall be acceptable.uPVC profile should be tested by BSI(UK) & SKZ(Germany) @25000 weathering hours Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Extra for brown colour wood texture weather resistance ISO certified quality.

Providing and fixing double glass unit of 20mm thick comprises of 5mm glass -10mm spacer -5mm glass thick filled with Argon gas between the two layer of glass is further finished on the side and is ready for installation. Type of glass is toughved and 90% transparancy.

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with; Budloo wood

French spirit polishing : Two or more coats on new works including a coat of wood filler

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : Newwork (two or more coats) over and including water thinnable priming coat with cement primer

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface Water thinnable cement primer

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete : a) 300x16x5 mm

b) 250x16x5 mm

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with floating coat of neat cement including cement slurry and curing complete but excluding coat of nosing of steps etc complete. 50 mm thick with 20 mm nominal size stone aggregate

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 5 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. With granite stone of area less than 0.50 sqm.

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.

Providing & fixing White vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. Orissa pattern W.C Pan of size 580x440 mm

Providing and fixing wash basin with C.I. brackets, 15mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a)White Vitreous China Wash basin size 550x400mm with a 15mm CP Brass single hole basin mixer

Providingand fixingwhitevitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes testing of joints complete as per direction of Engineer in Charge. (Internal work exposed on wall) a) PN - 16 Pipe, 25mm OD (SDR-7.4)

b) PN - 16 Pipe, 32mm OD (SDR-7.4)

Providing and fixing PVC waste pipe of required dia including bends,Tee door bend. L bend trap jointed with adhesive material ISI marked like prince, vector or equivalent brand all complete job. a) 110mm dia bore

b) 90mm dia bore

Providing and fixing of material for the insulation of pipe with nitrile tube , tapping with cello tape for inner wall fittings . complete job including carriage. 19 mm thick, 50 mm dia (OD) ( PPR 25 mmm)

Providing and fixing heat tape 33Watt on PPR pipes made of denforced or chromelox or equivalent make, as approved by Engineer InCharge , complete Job

Providing and fixing of material for the insulation of pipe with nitrile tube , tapping with cello tape , Rockwood 6 inch per side, wire mesh, polythene , tapping with cello tape aluminum sheet 26 gauge cladding with dia . complete job including carriage. a) 19 mm thick, 50 mm dia (OD) ( PPR 32 mmm)

b) 19 mm thick, 50 mm dia (OD) ( PPR 40 mmm)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing ball valve (PPR) of approved qulaity complete 32mm

Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 100mm sand cast iron grating for gully, floor or Nahani trap.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, out let and over flow pipes but without fittings and the base support for tank

Providing and fixing of material for the insulation of Water Storage Tank of with nitrile sheet , tapping with cello tape , Rockwood 6 inch per side, wire mesh, polythene , aluminum sheet 26 gauge cladding with dia of , complete job. 19 mm thick nitrile sheet

Providing and fixing automatic timer 30-35 watt including all complete job.

Painting top of roofs with bitumen of approved quality @17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : With residual type petroleum bitumen of grade VG -11

11 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @35 kg per cum of earth and gobri leaping with mix 1:1 (2clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: With common burnt clay F.P.S.(non modular) brick tile of class designation 11

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : 1st class kail wood

Earth work in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up inembankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m : All kinds of soil

Steel work welded in builtup sections/framed work, including cutting, hoisting, fixing in position and Instringers, treads, landings etc.of stair cases, including use of chequered plate wherever required, all

Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cemen tmortar 1:4 (1cement : 4 coarse sand) : 25 mm thick

Carriage of material from source to site including loading, unloading and stacking complete job. a) Cement/Steel an avg lead 01km

c) Sand an avg lead 20 km

e) Stone agg. an average lead of 20 km

f) Soiling stone an average lead of 20km

g) Earth an avg. lead of 07km

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

b) 2 X 10 sq. mm + 1 X 6 sq. mm earth wire

c) 2 X 16 sq. mm + 1 X 6 sq. mm earth wire

d) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. A) 1 x 1.5 sq. mm

b) 1 x 2.5 sq. mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. A) 5/6 A switch

b) 3 pin 5/6 A socket outlet

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supply, installation, testing & commissioning of GI Electrode Earthing with 84mm dia and 3 meter length, with 40mm x 6mm thick the electrode should be hot-dip galvinised. The GI Electrode shall be pre-filled with Cristaline Conductive Materila (CCM). The GI electrode shall be surrounded with BEE MOIST compound to provide maximum contact betwen the electrode and compound should be eco-friendly GI Electrode Earthing should be maintinance free and does not require regular manual addition of water . The earthing pit should be covered with PVC cover.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supplying and fixing MCCB in cubical panel board Providing and fixing following rating and breaking capacity MCCB FP in existing cubical panel board including drilling of holes in cubical panel and making connections etc. As required ( Make as per annexure enclosed) Change over switch FP 63Amp

Providing and fixing following rating and breaking capacity and pole MCCB wit thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 250 A,36KA,FPMCCB

Fabrication ,supplying ,installation testing and commisssioning of following pannel made out of 2mm thick M.S sheet, wall mounted ,vermin & dust proof ,indoor type with lockable type hinged doors,duly painted with provision for fixing of 1 no incomer MCCB . type change over switch including supply and fixing 2 set of Aluminium Bus bar ,and strip for housing MCBs 12 Nos , MF Digital Meter and and other allied accessories as required .(Make as per annexure)

Supplying and fixing following rating, 240/415 V, "C" curve, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning (above to 32 amp) TPN 63 Amp

Supplying and fixing of 1.1 KV PVC insulated and PVC sheathed XLPE Power Cable of following sizes on surface/surface cable tray,0.50 mtr bleow ground level etc. as required including carriage upto site of work. (Make as per annexure enclosed) 50 sqmm 3.5 Core-Armoured

Supplying and fixing of 120 watt LED Street Light complete with GI pipe bracket duly embeded along the paraper/ wall Wipro LRO2-501-XXX-57-1 or equivalent approved make.

Supplying and fixing following luminaries as required 10watt LED tube light fitting LL20-111-XXX-65NE3 wipro or equivalent make and model Philips/crompton greaves

20 watt LED tube light fitting. Model / equivalent make and model Philips/Crompton greaves.

Supplying and fixing of musica bell including making complete connections etc. as required (Make as per annexure).

Supplying and fixing of following electrical items suitable for operating on 240/230Volts AC, 50 Hz supply. including connections etc. as required. Exhaust fan 300 mm size (Heavyduty) CG transair or equivalant approved make

Supplying and fixing LED type down lighter round 15 watt LD 95-141-XXX-65-G1 of wipro or equivalent

Supplying and fixing LED type down lighter round 12 watt LD 95-141-XXX-65-G1 of wipro or equivalent

Supply, installation, testing & commissioning of LED 2'x2' recess mounted fixture that delivers at least 3000 lumens and wattage not more than 36 watt. The luminaries shall have a CRCa power coated body and a high efficiency diffuser. WIPRO CRCO10RO 38HP57GL OR equivalent approved make.

Supplying and co-axial drawing TV cable RG-grade 0.7 mm solid copper conductor PE insulated shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/recessed steek/PVC conduit as required.

Please Enable Macros to View BoQ information