Copper Control Cable South

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

Bid ENQUIRY NO: KPTCL/SEE/TR(Op)/Cir-South/EE(O)/AEE-1/JE-1/25-26/EPR-10 Dated: 25.06.2025

Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading

Guaranteed Technical Particulars

Please fill only in the light blue coloured cells.

Sl.No Particulars 2Cx2.5 sq.mm 4Cx2.5 sq.mm 4Cx4 sq.mm 4Cx6 sq.mm 19Cx2.5 sq.mm

a) Name of manufacturer

b) Place of manufacture

2 Cable Type & Category

3 Applicable specn & standards voltage Grade

4 Suitable for effective Earth/Unearth system

5 Continous current rating when laid in air in ambient temperature of 50°C and for maximum temp. of 70°C of PVC cables

6 Ration factors applicable to to the current ratings for various conditions of installation.

7 Short circuit Capacity

a) Shor circuit Amp. (rms) KA for 1 sec

b) Conductor temp. allowed for the short circuit duty (deg. C)

c) Cross sectional area (Sqmm)

d) No. of wires

e) Form of conductor

f) Direction of lay of stranded layer

9 Condutor resistance (DC) at 20° C per km-Maximum

a) Composition of insulation

b) Nominal Thickness of Insulation (mm)

c) Minimum thickness of insulation

11 Inner Sheath

b) Calculated diameter over the laid up cores (mm)

c) Thickness of sheath (minimum) mm

a) Type and materail of armour

b) Direction of armouring

c) Calculated diameter of cable over nner sheath (under armour), mm

d) Nominal diameter of round armour wire/dimensions of armour strip

e) Numbers of armour wires.

f) Short circuit capacity of the armour and duration

g) Dc resistance at 20° C (Ω/Km) & resistivity of armour

13 Outer Shaeth

a) Materail (PVC type)

b) Clculated diameter under the sheath

C) Min thickness of shaeth(mm)

d) Colour of shaeth

a) Guranteed value of minimum oxygen index of outer sheath at 27°C

b) Guranteed value of minimum temperature index at 21 oxygen index

c) Smoke density rating as per IEC 60754-1

d) Maximum HCL emission as per IEC 60754-1

e) All the factory acceptace test to be done as per relevant IS/IEC and KPTCL specification.

15 a) Overall diameter of cable

b) Tolerance overall diameter(mm)

16 cable drums (shall conform to IS 10418 & technical specification)

a) Max./standard length per drum for each size of acble (single length) with ±5% Tolerance (mtrs)

b) Non standard drum lengths

17 Whether progresive sequentail marking on outer shaeth provided

18 Indentification of cores:

a) Colour of cores

19 Whether cables offered are ISI marked

20 Whether cables offered are suitable for laying as per IS 1255

Note:- Deviations if any from the specifications given here (Schedule-I), which provides for improvement in the functioning of the equipment will be accepted. Such deviations and their advantages shall be clearly brought out in Schedule-II of the tender.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE- II TECHNICAL DEVIATION

Bid ENQUIRY NO: KPTCL/SEE/TR(Op)/Cir-South/EE(O)/AEE-1/JE-1/25-26/EPR-10 Dated: 25.06.2025

Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading

Please key in the Sl.No., Volume , Section , Clause , Desc as given in Booklet and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening.

For any further assistance for submitting your bids please call up KPTCL office. Please fill only in the blue coloured cells.

Please don’t insert your Bid values here or else your bid will not be considered for evaluation.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

TO, Superintending Engineer Ele., Transmission (Op) Circle-South, KPTCL, Bengaluru

The following are the Technical Deviations and Variations from and exceptions to the Specifications and documents Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading. Specification No……….These deviations and variations are exhaustive.Except these deiviations and variations, the material shall be supplied as per specification and documents.

SlNO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Date Name of the Firm, Address & GSTIN Number

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE- III COMMERCIAL DEVIATION

ENQUIRY NO. KPTCL/CEE/T&P/EE(P)/AEE(P1)/400/400KV CB/13-14 Bid ENQUIRY NO: KPTCL/SEE/TR(Op)/Cir-South/EE(O)/AEE-1/JE-1/25-26/EPR-10 Dated: 25.06.2025

Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading

Please fill Only in the Light Blue Couloured Box

Please key in the SlNo., Volume , Section , Clause , Desc as given in Booklet and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening. Please refer Vendor Manual attached for further details.

For any further assistance for submitting your bids please call up KPTCL Office.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

TO, Superintending Engineer Ele., Transmission (Op) Circle-South, KPTCL, Bengaluru

I have read each of the Clauses mentioned in INVITATION FOR BIDS , INSTRUCTION TO BIDDERS , GENERAL CONDITIONS OF CONTRACT, SPECIAL CONDITIONS OF CONTRACT and COMMERCIAL TERMS AND CONDITIONS.

The following are the commercial Deviations and Variations from and exceptions to the Specifications and documents Tender for Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading. No……….These deviations and variations the matrix shall be suppliedas per your specifications and documents.

SlNO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/ VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Date Name of the Firm, Address & GSTIN Number

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE- IV QUALIFYING REQUIREMENT DATA

ENQUIRY NO. KPTCL/CEE/T&P/EE(P)/AEE(P1)/400/400KV CB/13-14 Bid ENQUIRY NO: KPTCL/SEE/TR(Op)/Cir-South/EE(O)/AEE-1/JE-1/25-26/EPR-10 Dated: 25.06.2025

Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading

SHEET FOR TECHNO-COMMERCIAL OPENING

Please don’t insert your Bid values here or else your bid will not be considered for evaluation. Please fill only in blue coloured cells.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

TO, Superintending Engineer Ele., Transmission (Op) Circle-South, KPTCL, Bengaluru

Bidders Name and address :

Following (mentioned below) is the list of earlier order for……………... Complete in all respects executed by us,details of which are being furnished by us in the support of qualifying requirements for Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading.

Capacity as in qualifying requirements.

Supplies done over the past 5 years.

Sl. No. Manufacturer Parameters of equipment desired as per qualifying requirements Qty. Purchaser P.O Ref and Date of Order Date of Supply Date of commissioning Remarks

Date Name of the Firm, Address & GSTIN Number

SCHEDULE V Bid Form

Bid ENQUIRY NO: KPTCL/SEE/TR(Op)/Cir-South/EE(O)/AEE-1/JE-1/25-26/EPR-10 Dated: 25.06.2025

Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading

TO, Superintending Engineer Ele., Transmission (O) BMAZ(S) Circle, KPTCL, Bengaluru

Having examined the Bidding documents including Addenda Nos.

(Insert Number of sheets), the receipt of which is hereby duly acknowledged, we, the

undersigned, offer to supply and delivery

(description of goods and services in conformity with the said bidding documents and as

We undertake if our bid is accepted, to commence delivery within

(number) days and to complete delivery of all the items specified in the contract within

(numbers)days calculated from the date of receipt of your notification of Award

we agree to abide by this bid for a period of 180 days from the date fixed for bid opening under

clauses 17 of the instructions to bidders and it shall remain binding upon us and may be

accepted at any time before the expiration of that period.

until a formal contract is prepared and executed, this bid together with your written

acceptance thereof and you notification of award shall constitute a binding contract .

Date Name of the Firm, Address & GSTIN Number

SCHEDULE VI ASSESSEMENT OF FINANCIAL CAPABILITY OF THE BIDDER

Bid ENQUIRY NO: KPTCL/SEE/TR(Op)/Cir-South/EE(O)/AEE-1/JE-1/25-26/EPR-10 Dated: 25.06.2025

Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading

1 Name of the Bidder

3 Details of Material/ Work to be executed

4 Quantity tendered

Sl.No. Particulars

1 Annual Turnover for the last three years Sl No. Year

2 Liquid Assets

3 Capital assets for the last three years

4 Current Ratio for the last year

5 Current Assets

6 Current Liabilities

7 Documents to be enclosed. 1 Audited Balance sheet for the last five years

2 Banker's /Financial Institutions endorsement for limit of Financial leading.

Date Name of the Firm, Address & GSTIN Number

Place Desgination

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

Bid ENQUIRY NO: KPTCL/SEE/TR(Op)/Cir-South/EE(O)/AEE-1/JE-1/25-26/EPR-10 Dated: 25.06.2025

Design, Manufacture, Testing and Supply of Copper Control cable of the various sizes, required at various sub-stations in Tr (Op) Circle-South, KPTCL Bengaluru conforming to Technical Specifications. F.O.R.D at Store/Site basis, including insurance, transportation and unloading

Sl. No. Terms & Conditions As per tender As per Bidder

1 Name of the Firm To be furnished by the bidder

2 Place of Manufacture To be furnished by the bidder

3 Scope of the proposal Whether bidder agrees for the complete scope of proposal as per clause 2.0 of ITB

4 Power of Auttorney for signing the Documents To be furnished by the bidder

5 Bid Form To be furnished

6 Bid Security/EMD As per clause 9 of NIT

7 Bid Validity 180 days from the date of opening of Technical Bids (Excluding the date of opening of Technical Bids)

8 Manufacturer /Supplier Should be Manufacturer as per Clause-7.0, of IFB

9 Experience As per Clause-7of IFB.

10 Quantity Tendered / offered 1. 2Cx2.5 sq.mm- 150mtrs 2. 4Cx2.5 sq.mm- 1255mtrs 3. 4Cx4 sq.mm- 790mtrs 4. 4Cx6 sq.mm - 4040mtrs 5. 19Cx2.5 sq.mm- 5485mtrs

11 Prices The tenderer shall quote Firm Price only

12 Taxes & Levies as pe tender condition

13 Payment Terms As per Clause 25 of ITB

14 Warranty/Guarantee 24 months from the date of commissioning or 36 months from the date of supply as per Clause-26 of ITB

15 Penalty for delay in supplies ½ % per week, subject to a maximum of 10% Clause 33 of ITB

16 Delivery/Completion Schedule As per Section III of IFB

17 Termination of contract As per Clause 35 of ITB

18 Performance Security Clause 19.0 of ITB 5% of the value of order.

19 Guaranteed Technical Particulars To be furnished by the bidder as per Technical Specification

Date Name of the Firm, Address & GSTIN Number

Place Desgination