REPAIR TO PLUMBING, SANITARY WORKS, INTERNAL WATER SUPPLY AT ASTHA COMPLEX, REPAIR TO DOOR, WINDOWS, FLOORING, FALSE CEILING ETC IN CERTAIN BLDGS AND CERTAIN B/R WORKS AT ASTHA COMPLEX AND PERIODICAL SERVICES OF CERTAIN BLDGS AND REPLACEMENT OF CERTA

Amount

Demolition/Dismantling of Brickwork or stone/ boulder masonry, built in cement mortar incl all quoins, arches, pillars, etc complete all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with subclass 'B' bricks (old size bricks), straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

-ditto- all as per above here in but except bricks complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class ‘B’ bricks (old size brick) straight or curved on plan to any radius in half bricks thick walls, built in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas and brick walls, Ceiing etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick cement plaster in CM 1:6 on brick Work or concrete surfaces including finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L, Rendering 15mm thick in CM 1:4 on of brick work or concrete surface finish ever and smooth (w/o using extra cement) incl WPC as per user manual complete all as specified and directed by Engineer-in-Charge. (WPC will be measured and paid separately).

Supply only liquid WPC complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10mm thick in CM 1:3 over concrete surface as on ceiling, chhajja, shelves etc to match with existing surfaces finish even and smooth w/o using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for one layer of 3mm thick wall care compound of altek/birla putty on old scraped surfaces or new plasterd surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new plastered surface and applying two coats of oil emulsion distemper on wall over one coat of primer etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plaster surface & apply two coats of cement based paint over a coat alkali primer resistance and complete all as specified and directed by Engineer-in-Charge.

M&L for two coat of Acrylic smooth exterior emulsion paint over one coat of acrlic primer incl preparation of new plasterd surface complete all as specified and directed by Engineer-in-Charge. Note : Colour and make as approved by Engr-in-Charge.

M & L for preparation of new plastered surface and applying two coats of oil emulsion distemper on ceiling over one coat of primer etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces by removal of existing treatmen and applying two coats of oil emulsion distemper over a coat of primer on surface of walls through electrical operated grinder etc, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces by removal of existing treatmen and applying one coat of oil emulsion distemper over a coat of primer on surface of walls through electrical operated grinder etc, complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces by removal of existing treatment and apply two coats of cement based paint over a coat alkali primer resistance etc complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces by removal of existing treatment and apply one coat of cement based paint over a coat alkali primer resistance etc complete all as specified and directed by Engineer-in-Charge.

M&L for applying two coat of Acrylic smooth exterior emulsion paint on walls, pillars cornices etc surfaces by spray gun machine incl by complete removal of existing sureface & filling necessary putty where required as in pathces or nail holes obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed by Engineer-in-Charge.

M&L for applying one coat of Acrylic smooth exterior emulsion paint on walls, pillars cornices etc surfaces by spray gun machine incl by complete removal of existing sureface & filling necessary putty where required as in pathces or nail holes obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces by removal of existing treatment and applying two coats of distemper oil emulsion on ceiling over one coat of primer etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces by removal of existing treatment and applying one coat of distemper oil emulsion on ceiling over one coat of primer etc complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces and applying two coats of white washing on wall complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces and applying one coat of white washing on wall complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces and applying two coats of white washing on ceiling complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces and applying one coat of white washing on ceiling complete all as specified and directed by Engineer-in-Charge.

M&L for reparing of RCC projection, chajja, roof facia, celling by scrapping, cutting, derusting and cleaning exposed reinforcement surfaces of damaged loose RCC surface and applying neat cement slurry @ 3 kg/Sqm and filling the surface with cement plaster 1:3 one or two layer as reqd or PCC 1:2:4 as directed by Engr-in-Charge with or without facia and smooth finished and smotth edges incl two coats of finished to match with the existing surface at any height and in any situation including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L cement concrete type B-2 1:2:4 (40mm graded aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters buttreses columns, pillars, boundry pillars and posts and like for fixing of angle iron on top of boundry wall , including form work complete all as specified and directed by Engineer-in-Charge.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the mild steel wire (annealed) not less than 0.9mm dia or securing with clips and complete all as specified and directed by Engineer-in-Charge.

All as per item No 29 above but 6 to 8 mm dia and over and including in stirrups, spacers and binders and complete all as specified and directed by Engineer-in-Charge.

M&L for non skid ceramic coloiured tiles 7 to 8 mm thick (square/rectangular ) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor of shade & designed as approved by GE,set and jointed in neat cement slurry and pointed with white cement with colour pigment to match the colour of tiles,15 mm thick rendering in bedding layer or screed bed in cement mortar (1:6) in floors incl dismantling tiles etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 31 above but here- in area of each tile exe 0.11 sqm but n.exe 0.18 sqm, in floors & dado etc complete all as specified and directed by Engineer-in-Charge.

M& L for Glazed ceramic jointless light/coloured group of size 350mmx450mm, thickness not less than 6mm as in vertical surfaces such as skirting/dado etc., set and jointed in neat cement slurry and pointed with white cement and pigment to match, laid over and including 10mm thick plastering in cement mortar 1:4, incl dismantling tiles etc complete all as specified and directed by Engineer-in-Charge. Note : shade & design as approved by EIC/GE

M&L for Virified tiles light shade /dark shade 10 mm thick (square/ rectangular) polished, area of each tiles not exc 0.36 sqm , in floors, dado , skirting etc. set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer in CM 1:4 for laying floor finishes and pointed in white or coloured cement to match and incl dismantling tiles etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 34 above but here-in- area of each tiles exc 0.36 sqm but not exc 0.42 sqm, in floors & dado complete all as specified and directed by Engineer-in-Charge.

M&L for 20 to 25 mm thick Kota stone slab (Machine cut) of any size laid over and incl 20mm thick bedding layer in cement mortar 1:6 over neat cement slurry @ 3Kg/sqm over sub base , jointed and pointed in grey cement mixed with pigment to match the shade of slab including rubbing and polishing to achieve mirror finish complete as in flooring /steps/ riser / skirting incl dismantling stone slabs etccomplete all as specified and directed by Engineer-in-Charge.

M&L for Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrana white incl roundening the edge of stone complete all as spd and directed.

M&L for Granite 18-20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding ,rounding of edgeing and dismantling complete all as specified and directed by Engineer-in-Charge.

M&L for 25 mm thick PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) as in laying of floor finishes incl demolition complete all as specified and directed by Engineer-in-Charge.

M & L for 100mm thick PCC 1:2:4 type B-2 (using 40 mm agg. ) in hardstanding /base of flooring incl demolition complete all as specified and directed by Engineer-in-Charge.

M & L for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm agg. ) in sub base of flooring incl demolition complete all as specified and directed by Engineer-in-Charge.

M & L for 50 mm thick PCC 1:3:6 type C-2 (using 40 mm agg. ) as in plinth protection / path/ any paved area incl demolition complete all as specified and directed by Engineer-in-Charge.

M & L for chequered tiles of size 300 x 300 x 25 mm thick (colour and glazed approved by EIC) with grey cement and pigments laid over 15 mm thick screed bed in CM 1:6 bedded and jointed in neat cement slurry, incl dismantling complete all as specified and directed by Engineer-in-Charge.

M&L for machine pressed precast concrete interlocking paver block of 60mm thickness any shape and size confirming to IS 15658 -2006, with grey cement, pigment incl 25mm thick sand filling complete all as specified and directed by Engineer-in-Charge.

M & L broken stone hard core of gauge n.exc. 63mm, deposited, spread and leveled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

M & L for PCC 1:2:4 Type B-2 (using 40mm graded stone aggregate) as in flooring incl finishing the cement concrete surface even and smooth with using extra cement , rubbish off the primises and incl demolition complete all as specified and directed by Engineer-in-Charge.

M&L for Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' in on concrete slab 100mm all as specified and directed.

M&L for anodised aluminium framed work for door, window / vent (powder coated) aluminium section weighting 0.55kg/RM with one or more rebated incl jointed cleat for fixing etc complete all as specified and directed by Engineer-in-Charge.

M&L for anodised aluminium powder coated door shutter , aluminium section weighting not less than 0.55kg/RM incl necessary 4.8mm th sheet glass ordinary quality / frosted glass or ACP sheet incl joining with cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, lock , 2 x 150mm aluminium handles, 3 x 100mm hinges aluminium, 2 x 150mm Aluminium tower bolts,1xdoor stoper,1xHydralic door closer with each shutter any type incl taking down complete all as specified and directed by Engineer-in-Charge.

M&L for anodised aluminium powder coated window and ventilator shutters, aluminium section weighting not less than 0.55kg/RM incl necessary 4.8mm th sheet glass ordinary quality glass/ frosted incl joining with cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, lock , 2 x 150mm aluminium handles, 3 x 100mm hinges aluminium, 2 x 150mm Aluminium tower bolts complete all as specified and directed by Engineer-in-Charge.

M&L for aluminium Anodized powder coated fixed frame of partiton or fixed window / ventilator , aluminium section weighting not less than 0.55kg/RM incl 4.8mm thick sheet glass oridinary quality ' frosted glass or ACP sheet joining with rubber beading , aluminium snap beading complete all as specified and directed by Engineer-in-Charge.

S&F aluminium wire guard mesh of 4mm nominal dia of wire and average width of aperture 75 - 85mm and fixed with aluminium frame / staples complete all as specified and directed by Engineer-in-Charge.

M&L for 4.8 mm thick float glass ordinary quality' frosted glass and glazing with aluminum beeding and gasket to aluminum framework in square exc 0.50 sqm in each pane in repair complete all as specified and directed by Engineer-in-Charge.

S & F for plain gypsum board panel 12.5mm thick on ceiling with and incl necessary GI frame used with ' T ' or any section accessories etc of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm incl dismantling of walls and ceiling board any type and two coat of OBD over a coat of putty complete all as specified and directed by Engineer-in-Charge.

M&L in repair for PVC hollow wall panelling 7 to 8mm thick any colour/design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site complete all as specified and directed

S & F for 10 -12 mm thick glass door, frosted with certain logo, fixed with floor spring, fixed on floor with two nos stainless steel handle of 300mm on each leaf and fixed partition arrangement incl necessary provision to lock the door complete all as specified and directed by Engineer-in-Charge.

M&L for providing and fixing 10 mm thick plaster of paris ceiling (Gypsum anhydrous) of approved design/ pattern to flat surfaces incl all necessary MS frame work, 12 mm thick board and fittings as per standard practice and as per manufacturer's instrs reinforced with GI wire mesh incl dismantling of walls and ceiling board any type complete all as specified and directed by Engineer-in-Charge.

M&L for providing & fixing False ceiling with Gypsum based ceiling tiles and frame work (with aluminum foil on one side) of size 595 x 595 mm of thickness not less than 9 mm including with GI powder coated frame angle /tee grid frame work for ceiling with following specfication (a) S&F Angle of side 25x25x1mm powder coated (b) 25x25x1 mm GI powder coated at Bottom tee as in main member (c) 25x25x1 mm thick GI powder coated at bottom tee as ibn cross members (d) S&F 1.6mm dia GI wire suspenders alongwith adjustable clamps to maintains leveling inculding fixing to ceiling fasteners & dismantling of walls and ceiling board any type complete all as specified and directed by Engineer-in-Charge.

M&L for coral wall texture paint flasks type consisting of fiber natural gem, semi-precious pigmented granules, pearl and spary texture of high resistance, fire proof polymer alkali resistance, anti-corrosion and anti-condensation with natural stone, lime stone quartz etc. that given a scam less wall surface without joints, reples water ultra violet rays from sunlight including removing of, alage and fungus applied on wall or ceiling with trowel and roller complete all as specified and directed by Engineer-in-Charge.

M&L for Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm including removing of, alage and fungus applied on wall with trowel /roller complete all as specified and directed by Engineer-in-Charge.

M&L for box type steel window 1.25 mm thick made of ERW tube P-Section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter(two gauged shutters and two glazed shutter) of ERW tube P-Section size 50 x 20 mm and 1mm thick one/two Nos openable leaf consisting of two Nos sash bar of T-Section 20x3mm welded to frame with one No Vertical mullion of ERW box type T-Section of size 60 x 25 mm and 1.25 mm thick and FI 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like Handle, Tower Bolt, stopper, cleat, pintal hinges, hold fast etc. (i) Hold Fast, 150mm long of 120mm x 3 mm made to shape -04 Nos per window. (ii) Handle of Z sec 20mm x 25mm, 100 mm long -1 No per leaf (iii) MS Tower bolt 150mm long - 2 No per leaf (iv) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf (v) Cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge -1 No per leaf. (vi) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf . (vii) 8 mm square guard bar, 10 cm centre to centre. (viii) 40x6 mm flat iron all around for joint of both frame. (ix) stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples & 3mm thick, sheet glass ordinary quality and glazing with oil putty .(x) Two coat of synthetic enamel paint to MS window and guard bar , Incl taking down old steel / wooden window and making good dismantled portion with PCC 1:2:4 type B0 incl hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge.

M&L for pressed steel frames of size 105mmx60mm for doors with one or more rebates fabricated out of 1.25mm thick mild steel sheets including necessary fixing lugs, butt hinges (100mm medium weight-03 Nos), lock strike plate with and including filling of hollow portion in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and making good the existing surface in cement mortar 1:6, incl taking down old frame/chowkat complete all as specified and directed by Engineer-in-Charge.

All as per item No 62 above but here-in size of frame 125mmx60mm for doors complete all as specified and directed by Engineer-in-Charge.

S&F for factory made 35mm thick 2nd class hardwood plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F for 35mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match incl taking down old shutter complete all as specified and directed by Engineer-in-Charge.

S&F for 2nd class H.W. glazed and skelton door shutters 35mm thick, open rebated and prepared to received glass/gauge etc (without sash bars) edges of framing plain, chamfered or rounded and mitred , beads for securing glass etc the size of member of shutter as specified in SSR part-I clause 8.23(b) and fitted to chowkahts incl stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads & taking down old shutter etc complete all as specified.

S & F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube incl taking down old frame any type complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and raials with suitabale PVC sheet beading, and jointed together with solvant cement, fixing in the frame at side as per specification and drawing incl taking down old shutter & 3Nos- 100mm Aluminium hinges for each shutter complete all as specified and directed by Engineer-in-Charge.

S & F for Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge.

S & F for 3mm thick sheet glass ordinary quality glazing with oil putty in square n exc 0.5 sqm quality or description from steel frame and complete all as specified and directed by Engineer-in-Charge.

S & F for mild steel framed work as in grill, guard bars etc with ends of bars/FI shoulders and or riveted or forged in to spikes, framed guard bar and similar works confirming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge.

S & F in repair for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads complete all as specified and directed by Engineer-in-Charge.

S & F in repair 3mm thick sheet glass, ordinary quality and with oil putty in Square n. exc 0.5 sqm in each pane incl hacking out old broken glass from metal frame incl punching or drilling out old glazing pins/spring clips and glazed with oil putty complete all as specified and directed by Engineer-in-Charge.

S&F for MS butt hinges, medium weight, cold rolled mild steel 100mm long (ISI Marked) with welded or complete all as specified and directed by Engineer-in-Charge.

S&F for aluminum anodized barrel tower bolts of extruded section 150mm long (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F for aluminum handles cast type anodized 200mm long (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F for 250mm long aluminium alloy, anodised, sliding door bolt of 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed by Engineer-in-Charge.

S&F in repair, 150 mm ordinay rat tail rod pattern springs incl roller and rabber plate fixed to chowkhats in repairs incl necessary welding if reqd. complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel or iron surfaces of any description not otherwise described over 10 cm girth or width and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for one coat of synthetic enamel paint on steel surface including preparation of old steel surface width or girth exc 10cm complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint over a coat of pink primer on wooden new surfaces of any description over 10cm width or girth incl preparation of new surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for one coats of synthetic enamel paint on wooden surfaces of any description over 10cm width or girth including preparation of old surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for viterous china squating pan of (Orrissa Pattern) size 580x440 mm white with 'P' or 'S' trap front or back inlet and integral foot rest (excluding flushing cisteern and flush pipe) fixed in repair including lime concrete bedding as required set complete all as specified and directed by Engineer-in-Charge.

Fixing only for viterous china squating pan of (Orrissa Pattern) size 580x440 mm white with 'P' or 'S' trap front or back inlet and integral foot rest (excluding flushing cisteern and flush pipe) fixed in repair including lime concrete bedding as required set complete all as specified and directed by Engineer-in-Charge.

S&F for Vitreous China wash down water closet pan (pedestal pattern) with trap, white (excluding fixing bolts, flushing cistern and flush pipe) incl connection to drain and flushing pipe in repairs complete all as specified and directed by Engineer-in-Charge.

Fixing only for Vitreous China wash down water closet pan (pedestal pattern) with trap, white (excluding fixing bolts, flushing cistern and flush pipe) incl connection to drain and flushing pipe in repairs complete all as specified and directed by Engineer-in-Charge.

S&F of PVC flushing cistem low level white with all accessories of 10 ltrs capacity incl flushing pipe, brackets and taking down of old CI/PVC flushing cistern in repairs complete all as specified and directed by Engineer-in-Charge.

S&F for Vitreous China wash basin (Pedestal pattern), White, flat back, size 550x400 mm incl brass CP waste coupling 32mm dia with long screwed shank and fly nuts,32mm dia, chain and plug, porcelain stopper with and including PVC collapsible waste pipe of suitable length, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

fixing only for Vitreous China wash basin (Pedestal pattern), White, flat back, size 550x400 mm incl brass CP waste coupling 32mm dia with long screwed shank and fly nuts,32mm dia, chain and plug, porcelain stopper with and including PVC collapsible waste pipe of suitable length, fixed in repairs complete all as specified

S&F for One piece water closet with bowl for cupled WC with PP soft seat cover, cistern hinges fixing accessories and accessories set of size 650x375x750mm, 3.S trap outlet with cistern fittings and necessary fixing fittings complete, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

S&F for wall mixer with provision for overhead showes with 115mm long bend pipe on upper side, connecting legs and wall flanges, in repairs complete all as specified and directed by Engineer-in-Charge.

S&F for CP brass Centre hole mixer without pop up waste system 15mm bore for mixing hot and cold water screwed down for iron pipe for WHB, in repairs complete all as specified and directed by Engineer-in-Charge.

S&F for Soap tray brass chromium plated and fixed to plugs on wall with brass screws, complete all as specified and directed by Engineer-in-Charge.

S&F in repair Soap dish, vitreous China white, ap?proximate size 160x 160x90mm fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed by Engineer-in-Charge.

S&F for Towel ring brass chromium plated, fixed with brass screws and plugs, complete all as specified and directed by Engineer-in-Charge.

S&F for Brass Chromium plated shower roses 125 mm size incl arm with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

S&F in repair Stainless steel sink without drainboard, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe incl sink coupling, 40mm waste fitting, overall size915mmx460mm with bowl size 410 mm x 330mm x 160mm, etc complete all as specified and directed by Engineer-in-Charge.

S&F for Toilet paper holder,stainless steel, fixed with and including chromium plated brass screws and and wooden/plastic cleats on walls, complete all as specified and directed by Engineer-in-Charge.

S&F for Health faucet brass CP with 8mm dia 1.2 mtr long flexible pipe and wall hook fixed with brass chromium plated screws, complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/40mm-270 gms), complete all as specified and directed by Engineer-in-Charge.

S&F for 25 mm dia decorative/fancy type stainless steel curtain rod with brackets and knobs at both ends as per site requirement incl taking down old existing pipes with accessories complete all as specified and directed by Engineer-in-Charge.

S & F for Bib tap CP fancy type long body 15 mm bore with will crutch or buttewrfly handle screwed down screwed to iron pipe in repairs complete with all fittings complete all as specified and directed by Engineer-in-Charge.

S & F in repair Stop cock /angle CP fancy type 15 mm bore screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for Unions complete all as specified and directed by Engineer-in-Charge.

S & F in repair Stop cock concealed long shank chromium plated fancy type 15 mm bore screwed down high pressure with crutch or butter fly handle complete all as specified and directed by Engineer-in-Charge.

S& F for swan neck pillar cock fancy type chromium plated screw with iron pipe incl all fittings in repairs complete all as specified and directed by Engineer-in-Charge.

S&F for PVC connections 60cm long superior quality with PTMT nut on both side complete all as specified and directed by Engineer-in-Charge.

S&F in repair grating round 125mm size of CP complete all as specified and directed by Engineer-in-Charge.

S&F in repair 32 mm dia Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm?45gms/ 40mm-60 gms )complete all as specified and directed by Engineer-in-Charge.

S&F in repair 32 mm dia Waste coupling of PTMT (half or full threaded) suiotable for urinal . (Minimum weight 32mm?45gms) complete all as specified and directed by Engineer-in-Charge.

S & F in repair vitreous china urinals, half stall type (635x450mm) , complete including providing and fixing , bedding urinal against wall in cement mortar 1:2 , pointing around urinal back in cement , grating and union for discharge pipe, CP urinal spreader and fitting with bottel trap & CP waste coupling complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC water tank lid with locking arrangement complete capacity (500 ltr -1000 Ltr) complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15 mm dia bore steel tubing and connection including cleaning for refixing or removed to store complete all as specified and directed by Engineer-in-Charge.

S&F for GI tubing 15mm bore medium grde with all fittings and fixed complete to wall and ceiling or laid in floors etc incl cutting chases in brick wall pinning in making good in CM 1:3 to facings where required complete all as specified and directed by Engineer-in-Charge.

S&F GI tubing 15 mm bore medium grade medium grde with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Fixing only in repair steel tubing and connection 15 mm dia bore to wall and laid in floors complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection including cleaning for refixing or removed to store, 20 mm dia bore complete all as specified and directed by Engineer-in-Charge.

S&F GI tubing 20 mm bore medium grade medium grde with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Fixing only in repair steel tubing and connection 20 mm dia bore to wall and laid in floors complete all as specified and directed by Engineer-in-Charge.

S&Fin repair for Gun-metal globe or gate valves of 20mm bore , with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair 25 mm PVC float valve incl ball and rod complete all as specified and directed by Engineer-in-Charge.

S&F in repair 20 mm PVC float valve incl ball and rod complete all as specified and directed by Engineer-in-Charge.

S&F in repair cast iron body Door closer hydrau?lically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete unreinforced in of any desciption and in any position not otherwise specifically provided for (sunken floor) and concrete debris and rubbishoff to a distance n exc 100m complete all as specified and directed by Engineer-in-Charge.

M&L, for rendering 10mm thick in CM 1:3 with WPC in sunken slab complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of roof surface & applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced wih polyster non wove fabric (wt not less than 150 gms/sqm) land on primed surface by forced application, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed by Engineer-in-Charge.

M&L, cement concrete 1:7:12 F-2 (40 mm graded aggregate ) in lean concrete complete all as specified and directed by Engineer-in-Charge.d.

S&F for 110mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with dash ture nut and bolt at every 2 mtrs length complete , incl taking up/down old pipe with all fittings complete all as specified and directed by Engineer-in-Charge.

All as per ser item No 131 above but laid in trench or in floor complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm bore PVC Gully Trap setting / jointed with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm bore PVC bends/junction any radius complete all as specified and directed by Engineer-in-Charge.

Easing andAdjusting aluminium door and window including refixing beading after replacement of defective portions such as door closer, aluminium handles, hinges, locks, new rubber gasket, aluminium beading, preleminated prarticle board, sheet glass etc complete all as specified and directed by Engineer-in-Charge. Notes : Door closer, door spring, aluminium beading, preleminated gasket, aluminum beading, preleminated particle board, sheet glass shall be measured and paid separately under respective item of schedules.

S&F of 12 mm thick particle board preleminated on both side decorative choice etc complete all as specified and directed by Engineer-in-Charge.

S&F of floor door spring etc complete all as specified and directed by Engineer-in-Charge.

S&F of door closer hydraulically regulated design No 2 etc complete all as specified and directed by Engineer-in-Charge.

S&F of Mortice lock vertical type 4 lever etc complete all as specified and directed by Engineer-in-Charge.

S&F of Neoprene/EPDM Rubber gasket for fixing aluminium door and window shutters etc complete all as specified and directed by Engineer-in-Charge.

S&F of aluminium beading for fixing of aluminium door and window shutter etc complete all as specified and directed by Engineer-in-Charge.

S&F of 150 mm long aluminium tower bolts for aluminium door and window shutter etc complete all as specified and directed by Engineer-in-Charge.

S&F of aluminium handles 150 mm long for aluminium door and window shutter etc complete all as specified and directed by Engineer-in-Charge.

S&F of aluminium handles 100 mm long for aluminium door and window shutter etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair 2nd class hard wood beading straight (any size) for glazed/gauged joinery, renewed incl mitered etc complete all as specified and directed by Engineer-in-Charge.

M&L for repairs to sliding door bolt, hinges, pintel, locking arrangment, spike, roller, roller rails etc of steel gate/Wicket gate including welding /reveting to bring the steel gate /wicket gate in service condtions etc complete all as specified and directed by Engineer-in-Charge.

M&L for repairs to rolling shutter including necessary gressing, welding, locking arrangement including serviceing to gear box etc complete as to bring in service condtions etc complete all as specified and directed by Engineer-in-Charge.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., incl welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-Charge.

M&L for repairs to collapsible steel gate including necessary gressing, welding, locking arrangement including serviceing etc complete as to bring in service condtions complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm bore Twin one angle valve/ bib tap cast copper alloy chromium plated, fancy type, screwed down high pressure, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge.

S&F in repair corner shelf with CP railing 300mm x 300mm complete all as specified and directed by Engineer-in-Charge.

S&F in repair CP jet for EWC along with pvc connection complete all as specified and directed by Engineer-in-Charge.

S&F CP brass Health faucet with 15mm bore pipe complete all as specified and directed by Engineer-in-Charge.

S&F for liquid soap container of PTMT fixed with and incl CP brass screws and wooden/plastic cleats complete all as specified and directed by Engineer-in-Charge.

S&F in repair door seals made of aluminium strip powder coated 20 mm wide and provided rubber/ cotton mat lining fixed with screws to door shutters up to 1m width opening complete all as specified and directed by Engineer-in-Charge.

S&F double legged door stopper of aluminium alloy with rubber complete all as specified and directed by Engineer-in-Charge.

M/S CHANDER MUNI