SPECIAL REPAIRS OF BUILDING NO P-848 HELO HANGER WITH ANNEX BUILDING AT INS ABHIMANYU AT NAVAL STATION KARANJA

Amount

Chipping, removing carefully concrete work by low impact hammer, breaker without damaging the structure and cleaning and disposal of debris out side the premises etc., complete all as specified and as directed by Engr-in-charge. Note: Hard concrete should not be removed by force.

Material and labour for clean existing reinforcement with wire/ rotary wire brush, making the surfaces free from loose material dirt etc., complete and applying two coats of alkaline rust converting primer on the rebars, including cleaning the reinforcement, wire brushing to remove loose rust spalls, wash the rebars with clean water within 3 min and wipe it dry complete all as specified and as directed by Engr-in-charge. Make: FEOVERT of Krishna Conchem /Roff rust cleaner of Piddilite /Dr. Fixit Rust removal /ShaliRust of STP Ltd

Material and labour for applying two coats of epoxy based zinc primer in a span of four hours over the treated rebars and allow to dry for six hours. The application shall be by brush complete all as specified and as directed by Engr-in-charge. Make: Corroseal-ZR of Krishna Conchem /Dr. Fixit Epoxy zinc primer

Material and labour for cleaning all loose laitance on the concrete substrate and applying one coat of epoxy bonding agent on exposed concrete surface to ensure bond between old concrete and new concrete by brush application complete all as specified and as directed by Engr-in-charge. Make: Monobond SBR of Krishna Conchem /Dr. Fixit epoxy bonding agent /Shalicrete URP of STP Ltd

Material and labour for building up the profile of structural members by using latex additives (MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 = 1 monobond- 5 Cement-15 sand) in damaged areas in 30mm thickness including leveling profiling etc., complete all as specified and as directed by Engr-in-charge.

Material and labour for applying concrete protection coating on finished structural members exposed to atmosphere complete all as specified and as directed by Engr-in-charge. Make: IPNET of Krishna Conchem /New Coat from Dr. Fixit

Material and labour for drilling and fixing rohibb teflon nozzles in RCC members, including drilling holes of 12mm dia, 50 to 100mm deep holes. Works shall be carried out as under complete all as specified and as directed by Engr-in-charge. (i) Cleaning of holes: Clean the holes by air blower prior to fixing nozzles. (ii) Fixing of nozzles: Insert 12mm dia. Rohibb Teflon nozzles in cleaned holes. External end of nozzles to be machine to receive outlet of grouting gun. Fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing. Cure the system for min.12 hrs. (iii) Cutting of nozzles: Cut the nozzles by chisel after completion of grouting without damaging structural elements. (iv) In case crack upto 2mm wide, fix the injection nozzles directly over the cracks, at intervals of 6 to 9 inches, using a drilling machine. Fix PVC/ MS nozzles in these holes with fast-setting epoxy putty and let it dry for 2 to 3 days. Also, seal the crack between the ports with epoxy putty. (v) In case where the crack is wider than 2mm upto 4 to 5mm, drill holes at the sides of the crack in a staggered fashion, at intervals of 6 inches and affix them with epoxy putty as mentioned above. (vi) Also seal the face of the crack with a liberal application of the epoxy putty.

Material and labour for injecting of site mixed cement slurry grout, mixed in specified proportion containing cement, sand water with addition of plasticizers (approved make) and migratory corrosion inhibitors, water cement ratio shall be varied between 0.5 to 1.0 for each hole, shrinkage compensating cement slurry mixed to a lump free fresh creamy consistency, Mixing shall be done by mechanical mixer continuously stirring mechanically to keep cement particles in suspension. Injection of approved/ specified grout by means of pump at a pressure of 3-5 Kg/cm2 etc., complete till the grout mix flows out from the nozzle indicating complete filling of grout in the holes drilled complete all as specified and as directed by Engr-in-charge. Make: Epoxy grout - Dr. Fixit Epoxy injection /EPCO KP-HP-250 of M/s Krishna Conchem /Shaligrout EI of STP Ltd

Material and labour for injecting low viscosity (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories till nozzles refuses to accept the grout, including, mixing of materials, mixing of material components (part a&b) in the required quantities as per manufacturer's instruction by weigh batching. Grouting: Fill the grouting gun with concrete penetrating corrosion inhibitor. Maintain desired pressure in the gun by air compressor; maintain the pressure at exit (2 to 3kg/cm2) by monitoring pressure gauge at exit. Grout the material through prefixed nozzles in the structural elements @ 100ml per nozzle. Repeat the process for all the nozzles complete all as specified and as directed by Engr-in-charge. Make: EPCO-KP-100/Protectsil CIT / Ferogard 903

Replacement of steel reinforcement with TMT bars of appropriate size where 30% of cross section is reduced including dismantling of rusted steel complete all as specified and as directed by Engr-in-charge.

Providing and fixing additional main steel bar or stirrups of designed diameter in various structural elements like column, beams and foundations including drilling, bending, welding and fixing the bars with epoxy putty etc., complete all as specified and as directed by Engr-in-charge. Note: Steel provided on the basis of 1% of volume of concrete.

Material and labour for providing and applying jacketing around columns with micro concrete (Molith-MC) M40 including all lifts, shuttering, drilling holes and fixing shear anchor as per specification complete all as specified and as directed by Engr-in-charge. Note: Reinforcement shall be measured and paid separately (Rates including jacketing, formwork and micro concrete).

Taking down cement plaster on brick walls or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc., including removing debris directed for a distance max upto 500m complete all as specified and as directed by Engr-in-charge.

Material and labour for rendering 20mm thick on fair faces of brick /concrete surfaces with two coats i.e (15 mm thick backing coat in CM (1:6) and 5mm thick finishing coat in CM (1:4)), finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge. Note: WPC shall be measured and paid separately.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces of walls in cement mortar 1:6 finished even and smooth (with out using extra cement) with using sagol finish complete all as specified and as directed by Engr-in-charge.

Material and labour for epoxy base joint filler paint on external surfaces of walls to fill the cracks with and including resin and hardener in proportion as per manufacturers instructions complete all as specified and as directed by Engr-in-charge. Make: Pidilite / Focrac / Chemistic

Material and labour for new or old wall complete removal of existing treatment on external wall surface by sanding machine or any other mechanical means thereafter washing, rubbing down the surface, in order to remove dust, dirt, loose particles etc., and fill the visible cracks /joints with crack seal caulking compound after cleaning the surface by clean water. Apply a coat of primer (water based primer) and allow to dry for six hours. Thereafter, apply two coats of water proofing treatment on wall (WB high build anti carbonation cum water proofing including a coat of exterior grade weather proof acrylic emulsion paint by using Airless Paint Sprayer machine at any height of the building by using scaffolding. The material used for the treatment must have crack binding ability, water proofing properties and flexible (i.e cover hairline cracks upto 2mm effectively) and be elastomeric complete all as specified and as directed by Engr-in-charge. Make: Pidilite/ Beregr/ Asian Paints /Chemistic Note: External water proofing treatment on wall at any height of the building including acrylic paint shall be applied by mechanically Airless paint sprayer machine only.

Material and labour for preparation of new or previously untreated plastered surfaces of walls and applying two coats of acrylic antifungal paint exterior grade paint plain or camouflage pattern on one coat of primer complete all as specified and as directed by Engr-in-charge.

Material and labour applying 3mm thick wall care putty on new or old plastered surface and prepare the smooth surface with sand paper and applying two coats of oil bound distemper on walls complete all as specified and as directed by Engr-in-charge.

Material and labour for 5mm thick rendering on ceilings in cement mortar 1:4 and finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge.

Material and labour for three coats of white wash on newly plastered surfaces of ceilings including preparation of surface complete all as specified and as directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) roof or chajja padding of any description and any position not otherwise specifically provided for complete all as specified and as directed by Engr-in-charge.

Material and labour for plain cement concrete 1:3:6 type C-1 (Using 20mm graded crushed stone aggregate) in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3m and at every change of direction and filling the same with and including bitumen and sand 1:3 by weight complete all as specified and as directed by Engr-in-charge.

Material and labour for PCC 1:2:4 type B-1 (Using 20mm graded stone aggregate) as in roof /chajja padding /coving for maintaining roof /chajja minimum slope 1:6 complete all as specified and as directed by Engr-in-charge.

Material and labour for cutting opening through brick walls built in cement mortar for door, windows or enlarging existing opening, converting window into door openings, etc., or cutting out defective brick work for under pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, and rubbish not exc 50m and depositing where directed complete all as specified and as directed by Engr-in-charge.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) not exceeding 1.5 Sqm each, removing from the site including cutting holes required for taking out existing hold fast etc., complete all as specified and as directed by Engr-in-charge.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) exceeding 1.5 sqm not exceeding 4.0 Sqm each, removing from the site including cutting holes required for taking out existing hold fast etc., complete all as specified and as directed by Engr-in-charge.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm complete all as specified and as directed by Engr-in-charge.

Taking down shutters of any description not exc 1 Sqm complete all as specified and as directed by Engr-in-charge.

Supply and fix for solid PVC door frame of size 50x47mm made out of 5mm prelaminated PVC sheet and edges will be painted to match with prelaminated sheet, reinforced with MS square tube in opening complete all as specified and as directed by Engr-in-charge.

Supply and fix for factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face and 2mm prelam PVC sheet on back face in the frame at site complete all as specified and as directed by Engr-in-charge.

Supply and fix for second class hard wood plain solid straight chowkats and frame of wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed by Engr-in-charge.

Supply and fix for flush shutters 30mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete all as specified and as directed by Engr-in-charge.

Material and labour for painting to new wooden surfaces including preparation applying one coat of pink primer and two coats of synthetic paint complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise specified over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise specified over 10cm width or girth and applying one coat of synthetic enamel paint alongwith red oxide primer at any height including scaffolding complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of new painted steel surfaces of any description not otherwise specified over 10cm width or girth and applying one coat of synthetic enamel paint along with red oxide primer at any height including scaffolding complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs aluminium door /window /ventilator /partition, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame and necessary jointing cleats, glazing clips, powder coated aluminium snap beading, screws etc, complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts, hooks and eyes, peg stays and handles, concealed star lock for aluminium window, mortice lock vertical type size 100mm 04 lever for door, rubber beading suitable for fixing 4mm / 5mm thick glass in aluminium window / doors including connected items, with and including making good to the disturbed portion with its original specifications complete all as specified and as directed by Engr-in-charge.

Supply and fix 4 mm thick sheet glass, figured glass, pinhead type, glazing with oil putty area not exc 0.50 sqm each pane complete all as specified and as directed by Engr-in-charge.

Supply and fix Pre-laminated 18 /19mm thick particle boards, exterior grade, prelaminated both sides with decorative choice laminations complete all as specified and as directed by Engr-in-charge.

Supply and fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engr-in-charge.

Supply and fix 4mm thick sheet glass, ordinary quality, glazing with oil putty or with wooden or aluminium beads, area not exc 0.50 sqm each pane complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs aluminium anodised grill of design DG 104 pattern made out of 10mm dia rod fixed with and including standard aluminium frame of 'F' section of size 23.40mmx15.30mm & 1.4mm thick all as per manufactures instructions complete all as specified and as directed by Engr-in-charge.

Supply and fix in repair for aluminium body hydraulically door closer regulated, designation No.3 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix butt hinges size 100 extruded aluminium alloy with galvanised mild steel hinges pin anodised and fixed C-21 complete all as specified and as directed by Engr-in-charge.

Supply and fix aluminium handle, cast type anodized size of handle 150mm complete all as specified and as directed by Engr-in-charge.

Supply and fix aluminium anodized, barrel tower bolt of extruded section, length of bolt 150mm complete all as specified and as directed by Engr-in-charge.

Supply and fix 125mm brass double action spring hinges, with phosphor bronze wire wire spring, bright polished complete all as specified and as directed by Engr-in-charge.

Supply and fix extruded brass handles, fabricated type polished size of handle 150mm complete all as specified and as directed by Engr-in-charge.

Supply and fix rim latch with two levers, of brass body, stove enamelled finish; with brass knob or lever handle and fixed 150mm complete all as specified and as directed by Engr-in-charge.

Supply and fix in repair rim latch with two levers, of brass body, stove enamelled finish; with brass knob or lever handle and fixed 150mm complete all as specified and as directed by Engr-in-charge.

Material and labour 12mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative lamination fixed with screws to timber frame work complete all as specified and as directed by Engr-in-charge.

Supply and fix 50mm dia, polished, hardwood knobs fixed with screws complete all as specified and as directed by Engr-in-charge.

Supply and fix in repair 12mm thick vertical toughened glass as in door shutters/ partition with including stainless steel SS-304 patch fitting fixed with anchor fastener, stainless steel handles, each glass panes shall be exc 1.5 sqm, but not exc 2 sqm each, all edges of glass shall be diamond polished complete all as specified and as directed by Engr-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed by Engr-in-charge.

Supply and fix for framed work such as grills, gratings etc with ends of bars shouldered and riveted or forged into spikes, framed guard bars, barred iron doors ladders, framed balusters, walkways, railings frame work or water tanks and similar work at any height conforming to Fe-290 gde-E-16 complete all as specified and as directed by Engr-in-charge.

Supply and fix steel work in tubular trusses including special shaped washer etc., complete using ERW or induction butt welded tubes at any height conforming to IS-1161- 1998 at any height including scaffolding complete all as specified and as directed by Engr-in-charge.

Supply and fix roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., having Fe 410-W (Gde-E- 250) quality grade A at any height including scaffolding complete all as specified and as directed by Engr-in-charge.

Demolition of brick work or stone boulder masonry built in cement mortar or cement lime mortar complete all as specified and as directed by Engr-in-charge.

Material and labour for brick work with sub class 'B' bricks using old size bricks straight or curved on plan exc 6m mean radius built in CM (1:6) etc., complete all as specified and as directed by Engr-in-charge.

Material and labour for brick work with sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed by Engr-in-charge.

Complete removal of existing water proofing treatment of any description and in any position including cleaning, wire brushing, watering, removal of debris upto 1500m distance. Surface to be cleaned thoroughly using mechanical tools and tbe made free of dirt, oil. All cracks be repaired by cutting "V" groove and filling the gap using repair mortar Fibre Reinforced Polymer. Providing 75X75mm Coving/ angle fillet using the above repair mortar using Latex Based Bonding Agent as bond coat. All construction joints be opened 15X15mm and treated with repair mortar Fibre Reinforced Polymer. Honey combing to be pressure grouted with No Shrink cementatious Injection Grout. Water Proofing Application: The surface shall be free from standing water. Priming the surafce with UV stable Polyurethane water proof liquid membrane at 400gm/sqmt diluted with water 1:1. Applying 1st coat of ShaliPrime WP WB at 400gm / Sqmt. Then applying 1st coat of UV stable Polyurethane water proof liquid membrane White at 1Kg/Sqmt. Placing 40 Gsm Geotextile / FG Tissue as reinforcement followed by 2nd coat of UV stable Polyurethane water proof liquid membrane at 1kg/sqmt. Ensuring final curing of 36hrs before carrying any further work. Extending water proofing treatment and terminate at the top of the edge of the parapet wall. Sealing the Groove using repair mortar complete all as specified and as directed by Engr-in-charge. Note: In case of foot traffic for maintenance purpose, a separate walkway of 1m to be made with 40mm interlocking tile over Geotextile Make: ShaliUrethane BTD of M/s STP Limilted/ Sec-I PU500 of M/s SG Corporation/ Impermo 3002 of M/s Pratham Enterprises/ Opty D5HDPU of M/s Optimus Chemicals

Material and labour for screeding 10mm in CM 1:3 using sand on roof mixed with and including WPC @ 3% by weight of cement and finished the surface even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge. Note: Water proofing compound measured and paid separately.

Supply only water proofing compound complete all as specified and as directed by Engr-in-charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks, etc, removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed by Engr-in-charge.

Supply and fix for PVC (SWR) pipes single socketed in any length with rubber ring joints of 75 mm bore fixed in trenches or floor complete all as specified and as directed by Engr-in-charge.

All as per item No.67 here-in-before but as fixed on walls.

All as per item No.67 here-in-before but dia of pipe 110 mm.

All as per item No.67 here-in-before but dia of pipe 110 mm fixed to walls.

Supply and fix PVC (SWR) bends of (any radius) with access door of 75mm bore complete all as specified and as directed by Engr-in-charge.

Supply and fix PVC (SWR) bends of (any radius) 110mm bore complete all as specified and as directed by Engr-in-charge.

Taking up or down steel tubing and connections 15mm bore complete all as specified and as directed by Engr-in-charge.

Taking up or down steel tubing and connections 20mm bore complete all as specified and as directed by Engr-in-charge.

Supply and fix 15mm dia unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix 20mm dia unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., complete all as specified and as directed by Engr-in-charge.

Dismantling of stone slabs and tiles of any description or thickness in floor aprons, cills etc laid bedded and pointed in any mortar complete all as specified and as directed by Engr-in-charge.

Material and labour for non skid coloured ceramic tiles 7 to 8 mm thick (Square /rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, as in floors over screed bed or bedding layer of mortar 15mm in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed by Engr-in-charge.

Material and labour for glazed ceramic tiles in vertical surface 350x250x7mm/ 450X350X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering or bedding layer in cement mortar 1:4 complete all as specified and as directed by Engr-in-charge.

Supply and fix green marble 17/ 18mm thick machine cut, jointing and pointing with white cement slurry including 20mm thick screed bed or bedding layer of mortar in CM 1:6 complete all as specified and as directed by Engr-in-charge.

Material and labour for granite tile of 20mm thick on vertical surfaces such as skirting, dado, steps, wash basin table top, flooring, kitchen slab, machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing over and including rendering 15mm thick back coat in CM 1:6 complete all as specified and as directed by Engr-in-charge.

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete all as specified and as directed by Engr-in-charge.

Supply and fix for false ceiling with armstrong XL 24mm grid system of grid size 600x600mm with 14mm thick ceiling board of RH-90 of Armstrong. Grid shall be suspended from ceiling using 4mm dia pre straighten GI wire with 6mm nylon rawl plug and screws at 1200mm intervals at any height including scaffoldings complete all as specified and as directed by Engr-in-charge.

Dismantling asbestos cement sheeting, any gauge, thickness, including ridge/ transculant sheets complete all as specified and as directed by Engr-in-charge.

Supply and fix for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as at any height including scaffoldings complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs steel rolling shutters (thickness of laths 1.00 mm), push pull or manual type without ball bearing including top cover bottom plate, anchoring rod, mild steel handle and one shop coat of primer; erected in position complete all as specified and as directed by Engr-in-charge. Note: Net area of opening shall be measured for the purpose of payment, lock shall be measured and paid separately.

Supply and fix mild steel lock plate and handle made out of MS flat iron of size 35x5mm including welding to lath and painting with two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified and as directed by Engr-in-charge.

Supply and fix mild steel helical wire spring as per IS 6248–1979 for shutters exc 12 sqm but not exc 25 sqm complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs mild steel gear assembly complete including connecting and fixing the gear box to wall with 2 Nos hexagonal bolts 10mm dia, 10 cm long complete and grouting the bolts in cement mortar 1:3 complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs mild steel hood cover made out of mild steel sheet, 1.00 mm thick including bending the sheet to the required shape and fixing the same to the rolling shutter bracket plate including one coat of red oxide primer and two coats of synthetic enamel paint complete all as specified and as directed by Engr-in-charge.

Supply and fix gear worm set for gear operating gear shutter including re-alignment to connecting rod complete all as specified and as directed by Engr-in-charge.

Material and labour for greasing and easing in position of mild steel rolling shutter of area exc 20 sqm and not exc 50 sqm each for full movement and for easy operation for shutters complete all as specified and as directed by Engr-in-charge.

Taking down carefully copper /aluminum point wiring (light, fan, socket or power) complete, with wiring accessories such as bend boards elbows only, ceiling fittings etc., and removing material to store for safe coustody or for taking credit and making good disturbed surfaces of walls, floors, etc., complete all as specified and as directed by Engr-in-charge.

Material and labour for point wiring with 1.5 sqmm (nominal area) FRLS PVC insulated and unsheathed multistranded copper conductor cable (using colour code as per IS) 1100 volts grade drawn through and including 20mm dia medium grade rigid PVC conduit (ISI marked) concealed on wall surface with all accessories including concealed sheet steel terminal/ CI box with 3mm thick hylam/ masonite sheet top cover including 1.5 sqmm size PVC insulated unsheathed copper conductor multistranded cable for continuous earth conductor (using green colour) to common earth and connecting to earth dolly for the following complete all as specified and as directed by Engr-in-charge.

One light / buzzer point controlled by one switch 5 Amp, SP, one way 240 volts.

One 5 pin socket outlet 5 Amps on independent board.

All as per item No.94 here-in-before but with 2.5 sqmm multi stranded copper conductor 1100 volts grade FRLS PVC insulated sheathed cable with FRLS PVC 1.5 sqmm multi standard insulated unsheathed copper wire for continues earth on independent board.

All as per item No.94 here-in-before but using 4 sqmm (nominal area) for three phase and 4 sqmm PVC multistanderd FRLS copper conductor cable for earth continuity (green colour) for one power point.

Supply and fix switch piano single pole one way, 6 Amp (ISI marked) complete all as specified and as directed by Engr-in-charge.

Supply and fix switch socket combination 2 in 1, 3 pin, 6 Amp flush type (ISI marked) complete all as specified and as directed by Engr-in-charge.

Supply and fix switch socket outlet 15 Amp, 5-in-1, controlled by one switch (ISI marked) complete all as specified and as directed by Engr-in-charge.

Supply and fix in replacement MCB distribution board TPN, 4 ways, 415 Volts, 50 Hz, AC, double door made out of sheet metal phosphatised and painted with epoxy polyster based powder paints with 200 Amps rated bus bar and earth bar, ISI marked complete all as specified and as directed by Engr-in-charge.

Supply and fix in replacement MCB distribution board SPN, 8 ways, 415 Volts, 50 Hz, AC, double door made out of sheet metal phosphatised and painted with epoxy polyster based powder paints with 200 Amps rated bus bar and earth bar, ISI marked complete all as specified and as directed by Engr-in-charge.

Supply and fix in replacement MCB SP 240 V, 50 Hz, 10 KA conforming to IS 8828 of rating 5 to 32 Amps, 'C' series complete all as specified and as directed by Engr-in-charge.

Supply and fix in replacement RCBO DP 240 V 50 Hz 10 KA, 100mA confirming to IS 8828 of rating 40 Amps as per as in repairs all as specified and directed.

Supply and fix in replacement TPN MCB 415 V 50 Hz 10 KA confirming to IS 8828 of rating 40 TO 63 Amps complete all as specified and as directed by Engr-in-charge.

Supply and fix triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB 63 Amps complete all as specified and as directed by Engr-in-charge.

Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB complete with one single pole MCB 20 Amps complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED recess mounted 2x2 luminarie 36w fitting complete all as specified and as directed by Engr-in-charge.

Preparation of old or previously treated plastered surfaces of wall and applying one coat of acrylic antifungal paint exterior grade paint camouflage pattern complete all as specified and as directed by Engr-in-charge.

Supply and fixing of wiring for circuit/ submain wiring alongwith earth wire of size 2x4 sqmm for phase and neutral, 1x2.5 sqmm earth wire FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit of suitable size as required at site complete all as specified and as directed by Engr-in-charge.

BALAJI TRADERS

Har Siddhi Buildcon