REPAIR TO RCC POST, FENCING, GI SHEET AND FILLING OF SAND DUST MIX SAND AT 24 ED AF STN MANAURI

Amount

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion of concrete above GL or below GL complete all as specified and directed

M & L for PCC 1:3:6 type B-2, using 40 mm graded stone agg as in foundation, complete all as specified and directed.

S&F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as complete all as specified and directed. (eachline wire to be measured).

Dismantling of AC (corrugated/semi corrugated) sheet /PGI/CGI in roof covering including ridges all as specified and directed by Eng-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and making good to disturb surface, all as specified and directed.

All as per item no 5 above but Except sheets (Note : Sheets obtained from dismanling against item No 5 shall be reused).

Dismantling wrought iron or mild steel work of any description (i.e wind tie etc) not otherwise provided for etc complete all as specified and directed.

S & F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Rolled Mild Steel Framed work as in doors or Gates, fencing post, support on wall of angle or other section confirming to Fe 410 -W (Gde-, E- 250) A quality-with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering and hanging and fixing complete all as specified and directed.

M&L applying two coats of synthetic enamel paints over a coat of red oxide primer on new steel surfaces over 10 cm width or girth including preparation of surfaces complete all as specified and directed by the Engineer-in-Charge.

M & L for preparation of old steel surface exceeding 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified & directed.

Taking down cement plaster on brick or stone surface of wall built in cement sand mortar including racking out joints, hacking for key, scrubbing down with water etc and M&L for rendering 15 mm thick on fair face of brick walls or concrete surface in CM 1:4 with liquid water proofing chemical @ 200ml per cement bag finished even and smooth without using extra cement complete all as specified & directed. Note:- water proofing chemical shall be measured & paid separately.

M & L for preparation of new surface and applying two coat of cement base paint over a coat of primer all as specified and directed

Taking down cement plaster or cement lime plaster, any description from wall including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

M & L rendering 15mm thick cement plaster 1:6 on other than fair faces of brickwork or concrete surface and finishing even and smooth without using extra cement all as specified and directed.

M & L for preparation of new surfaces and applying 2 coats of OBD over a coat of primer all as specified and directed.

M & L for preparation of old surface and applying two coat of cement base paint complete all as specified & directed by Engineer-in-Charge.

M & L for preparation of old surface and applying two coats of Oil bound Distemper on walls complete all as specified & directed by Engineer-in-Charge.

M & L for preparation of old painted surfaces and applying one coat of Oil bound Distemper on walls complete all as specified & directed by Engineer-in-Charge.

M & L for preparation of old plastered surface of walls including cornices and apply two coat of white wash complete all as specified & directed by Engineer-in-Charge.

M & L for saw dust and sand in 1:2 ratio for filling, spreading and levelling in layers n. exc. 300 mm thick and well ramming including watering as required, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness complete all as specified and directed by Eng-in-Charge..

M&L for PCC1:4:8 type D-2 using 40mm graded stone aggregate as in sub base to floor etc complete all as specified and directed by Engr-in-charge.

Dismantling of paver blocks of any desciption and any thickness in floors, laid dry complete all as specifed and directed.

M & L for rubber moulded precast concrete interlocking paver block any shape and size glossy finish with and including 50 mm thick sand filling as in sand cushioning below interlocking tilesconfirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and directed.

M & L for rubber moulded precast concrete interlocking paver block any shape and size glossy finish with and including 25 mm thick sand filling as in sand cushioning below interlocking tilesconfirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified and directed.

M&L providing chequered cement concrete coloured tiles 25cm x 25cm x 22 mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment laid over and including screed bed or bedding layer 20 mm thick in CM 1:4 as in floors complete all as specified and directed.

M&L for PCC1:2:4 type B-0 using 12.5mm graded stone aggregate , as in coping etc complete all as specified and directed by Engr-in-charge.

M&L for providing 75 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate, finished even and smooth with using extra cement etc complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete (reinforced ) of any description and in any position complete all as specified and directed by Engr-in-charge.

M&L providing pre-cast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slabs set in CM 1:4 including necessary form work complete all as specified and directed by Engr-in-charge.

M&L mild steel deformed TMT bar 10mm dia and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed by the Engineer-in-Charge

Demolition of Brick works masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M & L for brick work with subclass “B” Old size bricks, straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specified and directed

M & L for rendering 15 mm thick on fair face of brick walls or concrete surface in CM 1:4 with liquid water proofing chemical@ 200ml per cement bag finished even and smooth without using extra cement complete all as specified & directed. Note:- Water proofing chemical shall be measured & paid separately

S&F galvanised (zinc coating) concertina coil 610mm dia (in stretched position) hot dip galvanised strip of 2.5mm dia core wire, weight not less than 9.5Kg/coil, 22 mm blade length, 14mm barbed width medium blade barb, distance between barbs 35mm c/c, with hardened galvanized steel clip fixed over Barbed wire with existing angle iron including dismantling of existing coil complete & as directed. Note :- (a) Horizontal barbed wire and angle iron support will be measured and paid separately under relevant item. (b) Measurement will be made for stretch length.

S&F galvanised (zinc coating) concertina coil 1050 mm dia (in stretched position) with heavy galvanized strip of 2.6mm dia core wire, weight not less than 14.5Kg/coil, 22 mm blade length, medium blade barb, distance between barbs 35mm c/c, with hardened galvanized steel clip fixed over Barbed wire with existing angle iron including dismantling of existing coil complete & as directed. Note :- (a) Horizontal barbed wire and angle iron support will be measured and paid separately under relevant item. (b) Measurement will be made for stretch length.

S&F in repair for chain link fencing MS galvanized, 3.14mm dia 75x75mm mesh fixed to RCC/ MS Angle Iron post including securing or tying with GI MS wire, staples etc complete all as specified and directed.

Supply only liquid water proofing chemical.

HARSH ASSOCIETES

M/S R S Traders