SPECIAL REPAIR TO CERTAIN B/R WORKS IN WATCH TOWERS ,IMPROVEMENT TO BATH ROOM OF CERTAIN MD ACCN AND PROVN OF TOILETS WITH SANITARY FITTINGS NEAR CULTURAL ACTIVITY GROUND AT AFS KANHERI HILLS UNDER GE AF THANE

Amount

Dismantling floor, hearth or wall tiling including cement morter beddind (but not backing removing seviceable tiles to store and rubbish off the premises , complete all as specified.

M&L for Glazed ceramic coloured (colour & shade as approved) tiles non skid of size 400x400x7mm thick as in floor set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

All as per Srl Item No-02.00 here-in-before but as on vertical surfaces such as skirting/dado over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified.

Material & labour for Glazed ceramic coloured tiles in vertical surfaces 350x250X7/ 350x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over including 10 mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces, complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortor complete all as specified.

M&L for Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platform sand like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to matchwith shade of granite including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed by Engr-in-Charge.

Demolition of un-reinforced cement concrete in any position complete all as specified.

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as directed by Engr-in-Charge.

Demolition RCC Roofs, flors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work complete all as specified.

M&L for use & waste wooden form work (rough finished surfaces ) to sides & soffits of Chajjas, parapets & facia and similar work n. exc 200 mm thick, complete all as specified.

M&L for RCC type B1, 1:2:4 ( using 20 mm graded Stone aggregate) as in Chajja, facia & RCC Slab etc , complete all as specified.

Mild steel TMT Mild steel bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips , complete all as specified.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified.

All as per Srl Item No 14.00 above here-in-before but size exceeding 1.5 Square metre and not exceeding 4 Square metre each , complete all as specified.

Taking down shutter of any description of exceeding 1 sqm but not exc 2 Sqm complete all as specified and as directed.

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

M&L for Pre-cast cement concrete block masonary with solid blocks type C1 (1:3:6), (using 20mm graded stone aggregate) exc 10 cm width and set in CM (1:4) all as specified and as directed by Engr-in-Charge.

M&L cement concrete 1:2:4 Type B-1 using 20 mm graded stone aggregate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating , complete all as specified.

S&F 35mm thick IInd class HW rail and style plain framed panelled factory made shutter (Two panel) with lock rail and panel of 9mm BWP,commercial ply or 12mm veneered particle beard with commercial veneering on both faces. The size of rail and stile as per IS :1003 (Part-I) kiln and chemically pressure treated , complete all as specified and as directed by Engineer-in-charge.

S&F in repair for 35mm thick IInd class hard wood glazed and skelton shutters divided into squares with plain chamfered or reounded miltred and related sash bars number to received glass gauze etc edges of framing plain chamfered or reounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I section 8 clause 8.20(a) supplied and fitted to chawkats , complete all as specified and as directed by Engineer-in-charge.

S&F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2020).

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Make: Rajshri or equivalent as approved.

S&F for 150 mm Aluminium anodised, barrel tower bolts of ex truded section and fixed complete all as specified.

S&F for 75 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified.

S&F for 100 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket tc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, luminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM Rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

M&L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved esign/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

S&F 4mm thick Sheet glass, ordinary quality and glazing with glazing clip and powder coated aluminium beading in square n exc 0.5 sq. m in each pane , complete all as specified.

S&F Stainless steel wire cloth 0.36mm nominal dia wire and average width of aperture 1.14mm and fixed with powder coated aluminium beading/wood beading , complete all as specified.

S&F in Repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames, glazed with putty or fixed with beads complete all as specified and directed

S&F 3 mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm in each complete all as specified.

M&L for cleaning and preparation of old painted surface of wall apply one coats of weather proof paint camouflage pattern complete all as directed.

S&F for 150 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed , complete all as specified.

M&L for Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

S&F Framed mild steel work of grade E-165 (Fe-290) as in framed work such as doors, gates or frame for cooler stand with gusset plates, rails, braces etc, drilled for fixing of sheeting or other covering of door etc, to be prepared for hanging or sliding etc including either hooks and hinges or steel hanging door fittings and hanging and fixing ,complete all as specified.

M&L for Pre painted galvalume aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified.

M&L for Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer,complete all as specified.

S&F PVC cabinet mirrors of size 550x400x75mm incl necessary shelves made of PVC sheets of minimum 5mm thick and mirror fixed on the front side of shutter complete all as specified and directed.( Make - Neelkamal, Prayag, Supreme)

S&F ,in repair, Drapery curtain rod/ Harrison rails of anodised aluminium alloy complete with MS brackets golden colour rings and sode caps fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and as directed by Engineer-in-charge.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified.

Taking up or down existing steel water tubing, 20mm bore alongwith connections fixed/laid in any situation, complete all as specified.

Supplying and laying of CPVC pipes 20 mm outer dia of SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of CPVC pipes 25 mm outer dia of SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F for Brass Elbow of 20 mm outer dia , complete all as specified.

S&F for reducer Brass Elbow (3/4 X ½) of 20 mm outer dia , complete all as specified.

S&F for Female Brass Threaded Adaptor (FTA/ FBTA) of 20 mm outer dia , complete all as specified.

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified.

S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified.

Fixing only, after cleaning old serviceable steel water tubing, 15mm bore and connections in new or old position using new fittings complete all as specified.

Fixing only, after cleaning old serviceable steel water tubing, 20mm bore and connections in new or old position using new fittings complete all as specified.

S&F 300mm Mild steel helical door spring including roller and roller plate complete all as specified.

S&F Towel rail, 19mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs as in repair complete all as specified.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe of 32 mm dia and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified.

S&F in repair 500 litres capacity rotational moulded, triple layer polyethylene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings & dismantling existing water storage tank, complete all as specified.

S&F 20mm bore PTMT ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified.

S&F in repair stop cock 15 mm cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe etc.

S&F in repair Bib tap of CP brass, 15mm bore, fency type screwed down, screwed for iron pipe or for brass ferrule complete all as specified. .

S&F in repair, Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ or 'S' trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, complete all as specified.

S&F in repair Viterous China wash down water closet pan (pedestal pattern), white incl. Seat and cover (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S&F in Repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F 15mm bore stop valves of cast copper alloy, screwed down, high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) fixed in repairs complete all as specified.

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed complete all as specified.

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm etc suitable for 15mm bore of pipe complete all as specified.

S&F 50 mm Low density polyethelne (LDPE) pipes of pressure rating 6kgf/sq. cm complete all as specified and directed.

S&F 125mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass as in repair complete all as specified.

S&F for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Dismantling CI pipe alongwith fittings of 75/100mm dia, below or above ground level or laid in floors, jointed in cement mortar and taking out complete all as specified.

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified. (fitting measured separately).

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent including jointing to waste pipe in run lead as in repairs complete all as specified.

S&F 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and stack clamps as in rain water pipes as in repair complete all as specified.

S&F ,in repair,PVC (SWR) branch pieces, double 'Y' shape (equal or unequal) or with parallel branches 110 mm dia ,complete all as specified and directed by Engr-in-Charge.

S&F,in repair, PVC (SWR) junction, single 'T' (equal or unequal) 110 mm dia ,complete all as specified and directed by Engr-in-Charge.

S&F ,in repair, PVC (SWR) junction, double 'T' (equal or unequal) 110 mm dia ,complete all as specified and directed by Engr-in-Charge.

S&F 110 mm bore PVC (SWR) bends/shoe any radius fixed to walls including distance pieces and stack clamps complete all as specified.

S&F in repair grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed

S&F in repair grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40 gms) complete all as specified and directed

S&F in repair PVC cover for tanks of capacity 500 to 1000 ltrs including taking out old broken covers with GI nuts and bolts 3/16" dia and 1" long bolts with washers (8 Nos with each cover and 2 Nos hing bolts and nuts 8 mm dia 50mm long complete all as specified and directed.

M&L for machine cut cudappa stone slab 20-25 mm thick over cement screed base as in jambs and soffits of lintel laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing including 10mm thick rendering in CM 1:3 ,complete all as specified ans directed by Engineer-in-Charge.

M&L for Surface preparation of non structural part by gentle chipping by manually to make the surface rough and thoroughly cleaned with air as per standard practice and directions of Engineer -in-charge (including removal of external plaster, wherever exists) COST inclusive of transportation, labour, conveying debris away from the out side of MD land, tools and tackles, lead and lift etc including necessery scaffolding ,form work etc, complete all as specified and as directed by Engr-in-Charge.

M&L for Providing and laying Renderoc SP-40 shrinkage controlled polymer modified single component, alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortor supplied in 25 kg moisture resistant bag when mixed with clean water at w:p ratio 0.18, achieves compressive strength (BS 1881 Pt. 116) -> 20 MPa at 1 day & > 45 MPa at 28 days. Tensile strength (BS 63199 Pt7)>2.5 Mpa at 28 Days, Flexural strength (BS 6319 Pt.3)>7 Mpa at 28 Days, During Shrinkage to ASTM C157-93, 28 days<1000 microstrain. Typical application inclues mixing entire bag with clean water about 4.25 ltr to 4.5 ltr, mixed with suitable container with heavy duty slow speed mixer machine to achieve lump free mortor consistency, placing and finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slab, piles etc, where tha thickness of application is less then 50 mm in patch as per specification after applying bounding coat item rate is inclusive of materials all labour tools and tackles, scaffloding and transportation etc. complete as per specification and as directed by Engi-in-Charge.

Taking down cement plaster or terrazzo from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M&L for Rendering/plastering, 15 mm thick in cement mortar (1:4) on brick or concrete surfaces including WPC, surfaces finished even and smooth without using extra cement complete all as specified. Note: WPC measured seperately

M&L for 15mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for 10mm thick rendering in cement mortar (1:3) on concrete surfaces, finished even and smooth without using extra cement as in ceiling complete all as specified.

M&L for preparation of newly plasterd surface of concrete or brick surfaces and applying Two coats ( having proportion @1.67 Litr/10 Sqm) of acrylic smooth exterior paint of required shade and including priming coat of exterior primer applied @ 2.20 Kg / 10 sqm, complete all as specified and as directed by Engr-in charge.

M&L for Preparation of newly plastered surfaces of walls & applying two coats of OBD on chalk whiting on plastered surfases complete all as specified.

M&L for Preparation of newly plastered surfaces of Wall & applying two coats of white wash complete all as specified.

M&L for Preparation of newly plastered surfaces of ceiling & applying three coats coats of white wash complete all as specified.

M&L for Preparation of old decorated surfaces of wall and applying one coat of white lime wash (white washing) on walls including corneces, pillars complete all as specified and directed.

M&L for Preparation of old decorated surface of wall and applying one coat of oil emulsion distemper complete all as specified.

M&L for Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for preparation of old surface of wall in any position washing down with water and cleaning the surface from all loose dirt, chalk, grease, fungal etc and finishing wall with one coat of weather proof acrylic paint etc ,complete all as specified and as directed by Engr-in-Charge.

M&L for Preparation of old decorated surfaces on ceiling and applying one coat of white lime wash including cornice and pillars etc complete all as specified.

M&L for Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for Preparation of old decorated surface of steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Demolation of unreinforcement cement concrete of any description and in any position not otherwise specially provided for or as in Sunken complete all as specified and directed.

M&L Cement concrete (1:5:10) type E-2 using 40mm graded stone aggregate in foundations, filling and mass concrete, as in filling under sunken floor portion complete all as specified.

M&L APP modified polymeric membrane with mineral finish on top min 3 mm thick & weighing n. less than 3.5kgs/sqm with mineral reinforced with polyster non-woven fabric(wt n.less than 150gm/m2) laid over cold bituminous primer by torch application method with min overlap of 75mm on longitudinal direction & 100m in the transverse direction complete all as specified and directed.

M&L for Rendering/plastering, 10 mm thick in cement mortar (1:3) on concrete surfaces of sunken floor and applying bitumen blown any grade applied two coats to concrete surface / rendering at the rate of 1.5 kg per sqm per coat and treating the sunken floor complete all as specified and directed.

Supply only integral water proofing compound (ISI Marked) complete all as specified.

M&L for Glazed ceramic coloured (colour & shade as approved) tiles non skid of size 300x300x7mm thick as in floor set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Glazed ceramic tiles, coloured (colour as approved), of size 300x200x7mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry over 10mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates,rivetting, etc., n exc 10 kg each brackets, conforming to FE 410-0 or FE 310-0 (Brackets over 10 kg each to be measured under `Structural Steel') complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 15cm and n. exc. 22.5 cm long and dia of bolt 11 to 15 mm , complete all as specified.

S & F MS Plate (Plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes with riveted bolted or welded attachment Fe-410-W(Gde-E-250) , complete all as specified.

M&L MS work flat iron, MS plates as in brackets, cleats, fasteners, wind ties, supports, base for posts etcwith riveted, bolted or welded attachment complete all as specified and as directed by the Engr- in- Charge.

Excavation in trenches in hard/dense soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and getting out complete all as specified.

M&L Hardcore of broken bricks of gauge n. exc 63mm, deposited spread and leveled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified..

M&L Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling as mass concrete or in sub base of floors complete all as specified.

M&L for Mild steel 8mm dia TMT bars as in reinforcement cut to length bent to shape required including cranking, hooking at ends and binding with mild steel wire (annealed) not less than 0.9mm dia as in stirrups complete all as specified.

Use & waste wooden form work (rough finished) to sides of footing, Beams, etc complete all as specified.

Formwork to sides of pillars, posts, struts, piers,columns, and stanchions Square, rectangular or polygonal etc. complete all as specified.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified.

M&L Reinforced cement concrete nomonal mix type B-1 (1:2:4) using 20mm graded stone aggregate as in columns, Footings and the like complete all as specified.

M&L Reinforced cement concrete nomonal mix type B-1 (1:2:4) using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 metre span and chajjas complete all as specified.

M&L Reinforced cement concrete nomonal mix type B-1 (1:2:4) using 20mm graded stone aggregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves , complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified.

Removal of surplus soil to a distance not exc 50 metre and depositing where directed at a level not exc 1.5 metre above the starting point complete all as specified.

M&L rendering/plastering, 5mm thick in cement mortar (1:3) on concrete surfaces, finished even and smooth without using extra cement as in ceiling complete all as specified.

S&F 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane glazing clip and powder coated aluminium beading in square n exc 0.5 sq. m in each pane , complete all as specified.

M&L for Cement concrete type D-2, 75 mm thick 1:4:8 (40mm graded aggregate) as in sub floors, sub bases, floors etc, complete all as specified.

S&F 100mm dia cast iron soil, waste and vent pipe, sand cast, in any length with or without ears with connections are fitted/sealed with M-seal including joints fixed to wall complete all as specified.

All as per Srl Item No 131.00 above but size 75mm.

S&F cast iron Nahani trap 100 mm dia with gratting including jointing to waste pipe fixed with concrete cement in (1:2:4) type B1 using 20 mm graded stone aggregate etc complete all as specified.

S&F Cast iron floor trap of 100 mm dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified.

S&F 15mm bore pillar tap, cast copper alloy, fency type with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified.

S&F bib taps, fancy type CP, screwed for 15mm bore of iron pipe or for brass ferrule and fixed complete all as specified.

S&F Stop/Angle Valve 15mm bore fancy type CP, Screwed down high pressure, with high pressure crutch or butterfly handle, screwed both ends for iron pipe or union complete all as specified.

S& F 15 mm dia Gun-metal, golbe or gate valves, with iron wheel head, screwd both end sor iron pipe and fixed ,complete all as specified.

S& F 20 mm dia Gun-metal, golbe or gate valves, with iron wheel head, screwd both end sor iron pipe and fixed, complete all as specified.

Surface excavation n. exc 30cm depth and averaging 15cm deep getting out in hard dense soil complete all as specified.

M & L 50mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in floor, fair finished , complete all as specified.

M&L for Sand filling under floors or in foundation including watering and consolidation , complete all as specified.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade ,complete all as specified.

S&F 150m dia SWG drain pipes laid in trenches and jointed, complete all as specified.

M&L for concrete bed to drain pipes of 150mm bore dia including paving under and haunching against the sides of pipes afrter they are laid and tested complete all as specified.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundating tiling and mass concrete ,complete all as specified.

M&L for providing precast cement concrete type B-1 1:2:4 using 20mm graded stone aggregate in manhole cover including necessary form work excluding reinforcement and set in CM 1:4 , complete all as specified.

M&L for cement concrete type B-2, 1:2:4 using 40mm graded stone aggregate in surface channels and drains , complete all as specified.

M&L for Point wiring with 1.5 sqmm copper conductor single core core , cable (multistrand) PVC insulated FRLS(unsheathed) concealed tdrawing in and including PVC conduit 25 mm dia, having wall thickness not less than 2 mm for one light pont, controlled by one , one way switch , including 1.5 sqmm PVC insulated FRLS (unsheathed ) copper conductor continuous earth wire complete all as specified and as directed.

All as per Srl Item No 149.00 above, but for One fan point controlled by one switch .

All as per Srl Item No 149.00 above, but with 2.5 sqmm for One 3 pin 16 amps socket outlet point controlled by one 16 amps switch on on Independent board.

Supply & fix modular switch 6 Amps, one way, one module complete all as specified and directed.

Supply & fix modular switch 16 Amps,one way, one module complete all as specified and directed.

Supply & fix modular socket 6 A/16 Amps, 6 Pin combined, two module complete all as specified and directed.

Supply & fix ceiling rose, 3 terminal, PVC/polycarbonate body complete all as specified and directed.

Supply & fix LED lights 1x20 watt ,220 V, AC decorative box type with driver,holder including LED tube light connecteing up with three core flexible copper conductor cable of suitable size from ceiling rose including connector block etc.and necessary fixing arrangement at any height and removing old unserviceable item complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size , complete all as specified and directed.

Supply and fix LED light fitting 1x10 W bulkhead minairs including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fix MCB distribution board SPN 8 way 240 volts, double door with IP 42 protection duly painted with epoxy based powder coated painting suitable for mounting MCB DP/SPN as incomer and MCB SP/DP as outgoings complete with 200 Amps rated busbar, neutral bar, earth bar connecting cable links with top and bottom removable gland plate including removing old unserviceable item complete and making good the disturbed surfaces to match with existing complete all as specified and directed.

Supply and fix MCB SP 6 to 32 Amps,10 KA, "C" series, 240 volts complete all as specified and directed.

Supply & fix MCB SPN 32 Amps 10 KA, "C" series, 240 volts complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & RCC cover all as specified & shown in elect plate No. 3 of SSR part I of 2020 including testing on completion complete all as specified.

M&L for Galvanised steel water tubing medium grade with complete all fittings such as elbow, unions, nipples, tees, bends, short pieces, connectors, back-nuts, caps, plugs, diminishing pieces and sockets etc as per site requirement of 25mm dia GI pipe line complete all as specified and directed by Engr-in-charge.

Supply, installing and testing Gun metal glove or gate valve, with iron wheel head, complete with suitable for 25mm bore pipe, screwed both side ends for GI pipe or unions and fixed in size 25mm dia complete all as specified and directed by Engr-in-charge.

Supply and fix XLPE insulated heavy duty electric cables with alluminium conductor, 1100 volt grade , cross sectional area 16 sqmm, 2 core, complete all as specified and directed.

PICON ENTERPRISES

Vinod Enterprises