PROVN OF ADDL STORAGE SHED FOR FURNITURE AT LIKABALI MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/ WORKS

Surface Dressing not exc. 15 Cm Deep and getting out in Soft/ Loose soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in Depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in Depth and getting out as in Hard/ Dense Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils), exc. 250.00 Metre but not exc. 500.00 Metre distance and depositing where directed at a level not exc 1.50 Metre above the Starting Point, complete all as specified and as directed.

M&L Sand (as approved) Filling under Floors, Foundations, Pre-cast Concrete Interlocking Paver Block, etc. including Spreading and Levelling, etc., complete all as specified and as directed.

M&L Hardcore Broken Stone or Boulders, Gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True Surface, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded aggregates) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) in Foundation including Raft, Footing, Foundation Beam for Column Basement Slab, under reamed Piles, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) Columns, Pillars, Piers, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) in Beams, Cantilevers, Bressummers, Lintels Over 1.50 Metre Span and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) in Chajjas and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flats, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides Pillars, Posts, Struts, Piers, Columns and Stanchions and Similar Work; Flats, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Chullah hoods, Chajjas, Weather Shades, Corbels, Water Troughs and Similar Items including Edges, Flats, Rough Finished Surface of Concrete, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200 mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregates), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregates) 40mm thick in Damp Proof Courses to Horizontal or Vertical Surfaces including mixing WPC and Use & Waste of Formwork and applying evenly a coat of Blown type Bitumen @ 1.50 KG/SQM and blinding with Clean Dry Sand @ 0.05 CUM/SQM, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured & Paid for separately under appropriate Item.

M&L Pressed Steel Sheet Frame for Door of Size 105x60mm with One or more Rebates including necessary Fixing Arrangement such as Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Projecting type Hinges with Steel Handle and Steel Peg Stay, complete With Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Projecting type Hinges with Steel Handle and Steel Peg Stay, complete Without Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of Size 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long (as approved) with Hasp, Staple (Bolt type) and Fixed Clips of Sheet, Cast or Extruded Sections and Fixed Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy, complete all as specified and as directed.

S&F Mild Steel Butt Hinge of Size 100mm and Welded to Pressed Steel Sheet Door Frame, complete all as specified and as directed.

S&F Aluminium anodised Handle of Size 150mm, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper having Overall length of Cover Plate 150mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixing in Floor and Fixed, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, Cut to length, Bent to Shape required including Cranking, Bending Spirally for Hooping for Columns, hooking Ends and Binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Rolled Mild Steel in Roof Trusses (Framed ), Trussed Purlins, Crane Gantries, Rails & Fastenings, Heavy Bracket Framing (Beam, Tee, Angle, Channel or Flat Sections) including Distance Pices, Cleats, etc., conforing to Fe-410-W (Gde-E 250), Quality 'A', complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or Notched (Ordinary and Counter Sunk) forming Holes, without any Aattachment, conform to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (Machine made) with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, Length of Bolt exc. 225mm but not exc. 300mm and Dia of Shank 16mm to 20mm, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregates) 100mm thick in Sub-base to Flooring, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregates) 75mm thick in Flooring, etc., Laid in Alternate Panels, finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Glass Dividing Strip 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregates) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Bitumastic Filling comprising 1 Part of Bitumen of Grade 85/25 and 3 Parts of Sand by Weight, complete all as specified and as directed.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/Top layer, finished Fair and Even, complete all as specified and as directed NOTE : Integral Water Proofing Compound (WPC) will be Measured and Paid separately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and Applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Ceiling and Applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and Applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

E/M SERVICES/ WORKS

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including Concealed PVC Conduit (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including Concealed PVC Conduit (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including Concealed PVC Conduit (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including Concealed PVC Conduit (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Run of 6.0 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable and 1-Run of 6.0 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn in and including Surface/ Recess PVC Conduit (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Run of Cable & 1-Run of PVC Conduit will deemed to be included in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Conduit only. Wires required for looping, etc. will deemed to be included in the Quoted Unit Rate.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp 3 Pin, 2-in-1, Flush type, 230 Volt AC, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp 3 Pin, 2-in-1, Flush type, 230 Volt AC, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F LED Bulkhead Light Fitting 1x10 Watt with LED Light Driver Holder and Connecting up with Flexible Copper Conductor Cable, 3 Core of suitable Size and Length from Ceiling Rose to Light Fitting, complete all as specified and as directed.

S&F LED Light Fitting 1x20 Watt, 220 Volt AC, Decorative Box type with Driver, Holder including LED Tube and Connecting up with Flexible Copper Conductor Cable, 3 Core of suitable Size and Length from Ceiling Rose to Light Fitting, complete all as specified and as directed.

S&F Exhaust Fan 450mm Sweep, Heavy duty, RPM 1360/1400, Copper Winding, Metallic Body complete with Louvers Shutter, 230 Volt, 50 Hz with Fixing Arrangement using Fastener, Connecting up with and including of suitable Size and Length Flexible Copper Conductor Cable, 3 Core, complete all as specified and as directed.

S&F MCB 6 Amp to 32 Amp, Single Pole, 'C' Curve, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F MCB 10 Amp to 32 Amp, Single Pole & Neutral, 'C' Curve, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F MCB 32 Amp, Triple Pole & Neutral, 'C' Curve, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 4-way, SPN, 240 Volt, Double Doors, Epoxy Based Powder coated suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 8-way, SPN, 240 Volt, Double Doors, Epoxy Based Powder coated suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and not exc. 1.50 Metre in Depth for Laying of Water Pipe Line, Cable Line, etc., Forming Surfaces to required Foundation/ Gradient and getting out in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps with Surplus Soil along the Route of the Water Pipe Line, Cable Line, etc., in Soft/Loose Soil, complete all as specified and as directed.

M&L Cutting on Existing Road not exc. 0.50 Metre in Width and not exc. 1.00 Metre in Depth including Making Good the Same with Cement Concrete 1:3:6 (40mm graded stone aggregate) 100mm to 200mm thick on Top Layer after necessary Returning, Filling in, Well Ramming and Levelling in Layers to match the Existing Road Surface Levels, complete all as specified and as directed. NOTE : Cement Concrete will be Measured & Paid separtely under appropriate Item.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in Quoted Unit Rate.

M&L XLPE insulated, Armoured, Heavy duty, Electric Cable with Aluminium Stranded Conductor, 1100 Volt grade, Cross-sectional Area 35 Sqmm, 3½ Core, laid in Trenches/ Ducts or Passing through Pipe or Fixing on Poles, etc., complete all as specified and as directed. NOTE : Necessary Earthworks, Sand Cushioning, Bricks Protection, GI Pipe, etc. will be Measured and Paid separately under relevent Items.

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE: Punned thickness of Sand Cushioning Only will be Measured and Paid.

Supply & laying Sub-class ‘B’ Bricks of Size 230x115x75mm, Kiln burnt, for Covering to UG Cable as Protection, laid Flat, Transversally Width Equal to the Length of the Cable, complete all as specified and as directed.

M&L Galvanised Steel Tubing Pipe 50mm bore (dia), Light grade with Bend, laid in Trenches or under Roads/ Flooring/ Culverts and/or fixing to Electric Poles with suitable Size Mild Steel Flat Iron Clamps, Bolts, Nuts, Washers, etc., complete all as specified and as directed. NOTE : Cost of Mild Steel Flat Iron Clamps, Bolts, Nuts, Washers, etc. as required / directed will deem to be included in the Quoted Unit Rate.

Supply, Installation, Testing & Commissioning Factory made LT Feeder Pillar Box Outdoor type, Platform mounted of Size not less than 600x500x450mm suitable for 415 Volts 3 Phase, 4 Wire system, 50 Hz Supply having Copper Bus-bars 200 Amp for Phases & Neutral, installed on Porcelain/ Epoxy Insulator, Dust & Vermin Proof (IP54 Protection) and Painted with Two Coats of Syntheitc Enamel Paint over a Coat of Red Oxide Primer and made out of 3.15mm CRCA Sheet Self moulded type and 50x50x6mm Angle Iron Frame, Front and Rear Opening with Double Shutter and Locking Arrangement with 50mm Lock of Make Navtal/ Harrison and including grouting of Feeder Pillar Box with necessary Cement Concrete 1:2:4 (20mm graded stone aggregate) Work including necessary Connections, comprising following Accessories:- (a) MCCB 63 Amp, 4 Pole, 16 kA - 01 No. (b) MCCB 40 Amp, 4 Pole, 16 kA - 02 No. (c) Volt Meter 0-500 Volts, Square Flush pattern, Digital type - 01 No. (d) Amp Meter 0-200 Amps, Square Flush pattern, Digital type - 01 No. (e) Indicating Lamp LED type at Incoming Phases - 01 Set (f) Internal Wiring with PVC insulated Copper Conductor Multi-stranded Cable 1100 Volt grade, IS:694 marked of appropriate gauge with all Copper Lugs (g) MCCB shall be provided with suitable Spreader of Copper Conductor for fixing Incoming Cable.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregates) and Pre-cast RCC Cover Slab of Size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregates), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick burried directly in Ground (Earth Pit not less than 2.25 Metre below Ground Level) with Top edge of the Plate not less than 1.50 Metre below Ground Level, connected with and including Galvanised Earth Strip of Size 32x6.0mm by means of Bolts, Nuts, Check nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar with GI 40mm bore (dia) Light grade Protection Pipe, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc. 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion, complete all as per specified and as directed. NOTE : All Joints should be joined by Exothermic Welding or Brazing.

M/s A R Traders

M/S Raju prasad

B S ENTERPRISE

SHRI MANOJ KONWAR

M/S Build Tech

M/s United Builders